Latitude D410 (Win 7), cannot activate wireless

Similar Questions

• Latitude D410 (Win 7), WLAN 1350 Code 10

  As a result of this post, I bought a Dell Wireless 1350 WLAN mini-PCI card and installed this morning.

  I followed the instructions of Philip to download the driver from Microsoft in the catalogue, but after the installation, I get an error Code 10 (this device cannot start).

  Then I tried the driver Dell here (for XP), but now I get an error Code 35 (your computer's system firmware does not enough information to properly configure and use this device. To use this device, contact the manufacturer to obtain a firmware or an update of the BIOS of your computer). The BIOS is updated.

  SysInfo reports the following (this does not bring the mini-PCI card):

  Host name: LATD410
  Name of the operating system: Microsoft Windows 7 Home Premium
  OS version: 6.1.7601 Service Pack 1 Build 7601
  OS manufacturer: Microsoft Corporation
  OS configuration: Standalone Workstation
  OS Build type: multiprocessor Free
  Registered owner: Stephanie
  Registered organization:
  Product ID:
  Original installation date: 09/11/2013, 12:27:29 AM
  Starting system: 11 23, 2013, 11:37:13
  System manufacturer: Dell Inc..
  System model: Latitude D410
  System type: X 86-based PC
  Processor (s): 1 processor installed.
  [01]: x 86 family 6 Model 13 Stepping 8 GenuineIntel ~ 1600 Mhz
  BIOS version: Dell Inc. A05, 28/09/2005
  Windows directory: C:\Windows
  System directory: C:\Windows\system32
  Starting device: \Device\HarddiskVolume1
  Local system: en - us; English (United States)
  Input locale: en - us; English (United States)
  Time zone: (UTC-05:00) Eastern (U.S. & Canada)
  Total physical memory: 1 015 MB
  Available physical memory: 709 MB
  Virtual memory: Max size: MB 2 039
  Virtual memory: available: 1 434 MB
  Virtual memory: in use: 605 MB
  Office (s) swap file: C:\pagefile.sys
  Domain: workgroup
  Logon server: \\LATD410

  Network adapters: 1 card installed.
  [01]: Broadcom NetXtreme 57xx Gigabit Controller
  Name of the connection: connection to the Local network
  DHCP enabled: Yes
  DHCP server: 192.168.1.1
  IP addresses
  [01]: 192.168.1.6
  [02]: fe80::88c5:13f6:2106:6db4

  Again, all my apologies that I realized that the card was not properly seated in the slot of the mini-PCI card. He pulled out, re-sitting there and voila! Operational wireless!

• Satellite Pro L10 - cannot activate wireless

  Just installed 2 new maps memory of 512 MB to L10 up to 1 GB maximum memory. A basic 256 MB before and became really slow.
  However, now cannot access the internet without wire - worked very well before, although slowly.

  I get the message "wireless communication switch is turned off", despite press the silver on the front and try Fn + F8. Seems turns a second then turns off again. I've never had to do before.
  Everything else seems fine. Running XP OS.

  Anyone has any ideas please?

  Hello

  To be honest, I doubt that this has something to do with the RAM upgrade. This doesn t usually affect the function of your laptop wireless.

  Anyway, first of all, I would try reinstalling the WLAN driver. You can get the latest version on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Also, be sure that the BIOS version is the most recent.

• Satellite Pro L450D-12 x - cannot activate wireless

  I recently installed Windows 7 Home Premium 32 - bit clean and am currently unable to connect to any wireless network. I went to control panel > network & Internet > manage wireless networks and it says "Wireless is not currently enabled.

  There is no switch to turn it on on this model. I also tried to go to the mobility Center Windows, but the option "turn wireless on" does not appear. An option to activate the wireless is not anywhere in summer as seen in the Network & Sharing Center or Device Manager. I also tried holding down the FN key and pressing F8, but it is not seen not work that the WiFi light is still orange.

  Any help would be appreciated and thanks in advance.

  Maybe stupid question now but why you installed Home Premium when your laptop was offered with the original Toshiba Win7 Professional recovery image?
  As you know recovery image contains all the necessary drivers, tools and utilities and all in working order.

  In your case, I can only imagine cards flash don't work correctly, but why this happens, I can't say with certainty.
  Is the card properly installed wireless (Device Manager)?
  Have you installed all the stuff from Win7 from Toshiba download including value added package (VAP) page?

• Re: Satellite L450D-128 - cannot activate wireless LAN

  Hello

  This laptop specific doesn't have a wireless to turn on/off switch. I can't seem to be able to locate the "wireless" on the Control Panel, in order to enable it.

  Help, please!

  Hi lil_red_rose,

  The laptop doesn't have a WIFI hardware switch, but you can use the combination of keys FN + F8 to disable/enable the feature WLAN.

  Also if the wireless network adapter is not recognized, press the key combination mentioned above to activate the wireless network card.

  Check this box!

• Satellite P755-S5393 - cannot activate wireless using Fn + F8 keys

  I have Toshiba P755-S5393 (PSAY1U-05W027) itfacing WIFI problem is not activate using the Fn + F8 keys.
  Initially I was facing problem with auto power-off, I diagnose and disconnection of the electric connection of the media Panel since then my wifi is not activate even using the Fn + F8 key combination.

  Solutions and suggestions are welcome!

  Aamir Malik

  Hi Aamir Malik

  Satellite P755-S5393 has been preloaded with Win 7.

  If you still use this system, you should first check if the other next to the combination FN + F8 function keys work correctly.
  If the keys n t work, you must install additional Toshiba as software
  TOSHIBA Value Added Package and Toshiba Flash cards support utility

  Drivers & updates for this model is located on the Toshiba USA support page:
  http://support.Toshiba.com/support/modelHome?FREETEXT=3167433

  Where only the combination FN + F8 does not work, I recommend reinstalling the WLan driver.

• HP Elitebook p 8460 - cannot activate wireless. the pilots checked and setting. Wireless disabled

  HP Elitebook 8460p - is there another way to turn on the wireless on an HP laptop?  I checked the settings, bios and made sure the wireless card in the laptop works. The drivers are installed correctly. When troubleshooting, it comes up with "activate the wireless. Nothing happens when you press the button. There is orange.

  Hey ATL,.

  I want to come and hard reset the computer. This usually solves problems of this kind. Here is a link with more information and how to perform the hard reset: http://h30434.www3.hp.com/t5/Notebook-Hardware-e-g-Windows-8/How-to-perfom-a-Hard-Reset-to-resolve-Hardware-Software-Issues/m-p/1965747#M84778

  Let me know if it helps!

  Thank you

  Sean S

• Cannot activate wireless home router N. WRT120N model number

  The problem is that I have Vonage phone service that requires the internet service.  I spoke with several agents of Linksys, none seem to understand the problems or know how I connected.  In short, with the Linksys modem, the modem from Comcast and the Vontage, I need help on how to get the router to work without messing up my phone service.  Thank you.

  bohochic323 wrote:

  That might work... but who could slow the VOIP connectivity.  but you can fix this by configuring the QOS.  Click this link for the steps.

  VoIP requires a tiny amount of bandwidth and download speeds Comcast offers, I highly doubt that would be a problem. Latency and jitter are the things that require the most attention.

• I can see the webcam on my Dell Latitude D630 laptop, but cannot make it work on Skype... This isn't seeit. How to activate the webcam to use?

  I can see the webcam on my Dell Latitude D630 laptop, but cannot make it work on Skype... This isn't seeit. How to activate the webcam to use?

  Hello markward4905

  You should be able to download the drivers from the website of the manufacturer of your web cam.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Expert - consumer:www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com

• Satellite L300-01:00 - DVD in PIO mode, cannot activate DMA mode

  Hello everyone,

  Recently, I have a laptop Toshiba L300-01:00 and I have a little problem with the DVD-ROM drive. Maybe some of you can help me with their knowledge. So here's the problem:
  The DVD runs very slow, I guess in the PIO mode. I can't switch to DMA mode because there is no options.

  On ' Device Manager / IDE ATA/ATAPI controllers ' options are a single - 'Intel(r) ICH9M-E/M SATA AHCI Controller' where you cannot activate DMA mode.

  I have WinXP SP2, SATA and all the other drivers installed.

  So my question is, how can I enable the DMA mode for the DVD player?

  Thank you very much.

  Hello

  I have a laptop with installed U400 XP OS and I the primary IDE channel entry into the IDE ATA/ATAPI controllers.

  Main channel that you can switch to the PIO or DMA is available in IE.

  Now the question is; How do you install XP on your laptop?
  Usually, the SATA mode must be set to AHCI in the BIOS, and you must include the SATA drivers to install Win XP on this laptop.

  Then a primary IDE channel should if poster in devices and the PIO or DMA settings manager should be there.

• Cannot activate XP Repair, installation ID does not work on the phone

  Hi all, I recently had to run a repair of Windows XP Edition family due to a driver issue and finally managed to return to the start screen and try to log in, but it wont let me connect you without activation (I suppose some confusion because it is installed on my computer for more than 30 days, but the repair made me have to reactivate).  So, I tried to start safe mode and was able to connect here in the version without networking.  Unfortunately, when I try to activate by phone (no network connection, the default ethernet driver was the cause of all this to start), the automated thing will not take the installation ID that is displayed in the activation page.  I know that I have a valid product key and the original disk, as I used it a year ago to re - install on a new hard drive, but I have no way to actually enter the product key!

  Assumptions on how I can try to work around this problem for long enough to activate online (I use a USB wireless, but the computer must be started in order to establish the connection), or why the crazy long installation ID does not work?

  Thank you very much

  Eric

  Hi EWool,

  • Have you tried to activate the normal mode?

  You cannot activate Windows XP safe mode and most of the drivers does not work in safe mode.

  I suggest that you contact the support of Microsoft telephone activation to reactivate Windows XP.

  How to find a phone number for a Microsoft Product Activation Center

  http://support.Microsoft.com/kb/950929

• I have a dell latitude d600. I use proset/wireless wifi intell. I want to spend to 87112 wzc. How can I do this?

  I have a dell latitude d600. I use proset/wireless wifi intell. I want to spend to 87112 wzc. How can I do this

  original title: 871122 wzc help
  Hello!
  I made a goof my wireless configuration to try to resolve a bad connection to the local network at home.  This response of Amnah_95 solved problem by following the instructions and a reboot.  Thanks Amnah_95.
  I think you've got the third-party software installed on your laptop to configure the wireless adapter. Third-party software seems to have disabled the Wireless Zero Configuration (WZC) Microsoft service. You will need to reactivate it.

  Follow the steps below to activate the automatic configuration on your laptop.

  1. Click Start, click Run, type % SystemRoot%\system32\services.msc/s, and then click OK.

  2. double-click on Wireless Zero Configuration.

  3. in the startup type list, click Automatic, and then clickApply.

  4. in the Service status area, click Start, and then click OK.

  Software configuration of certain wireless adapters removes the automatic configuration service. If this is the case, you can try this fix by changing the registry value.

  WARNING: Editing the registry can be dangerous, use it at your own risk.

  1. click on start - run and type reg. And then click OK.

  2. browse this registry key: HKEY_LOCAL_MACHINE es\WZCSVC

  3. next, create a DWORD value and name it 'Start' and set it to 2.

  • Proposed as answer byAmnah_95, Tuesday, July 6, 2010 13:32
  • Marked as answer bysupport Cody - engineerMicrosoft SupportModeratorThursday, August 19, 2010 12:41 AM

• PROBLEM! Cannot view wireless networks!

  Hi, I am currently running Win 7 Ultimate 64 bit on my office and cannot view wireless networks!

  I tried to use two wireless adapters and both show active although they cannot show all networks.
  LAN works perfectly well and when I try to add a wireless network, it is said "an unexpected error has occurred."
  I have updated drivers for two adapters to the correct version wireless and little. No yellow icon in the Device Manager.
  I also checked to see if power saving has been enabled for the device and power options that are disabled.
  Two wireless adapters are using a USB port, not PCI. I abandoned everything simply! I need some advice on how to solve this problem! I can provide more information if necessary. But please help me with this problem :(
  I also disabled anti virus software and my firewall!
  The wireless adapter, I am using is the:
  TRENDnet TEW-649UB Wireless USB adapter N speed

  UPDATE! :
  We have some progress I uninstalled all the previous windows updates and can now see wireless networks (such as firewall/AV). The problem I have now is that when I try to connect it said "Windows could not connect. He also says in the settings of cards tab my wireless adapter is "authentication attempt.

  Hi Tatiana,

  ·         Have you tried to install the drivers from the manufacturer's Web site?

  ·         Have you checked if the network card works on another computer?

  Download drivers card network from the manufacturer's website and check manually.

  http://www.TRENDnet.com/downloads/list_subcategory.asp?SUBTYPE_ID=1353

  Alternatively, you can deal with this problem due to security software. I suggest that disable you the security like anti-virus and firewall software and check if the problem persists.

  http://Windows.Microsoft.com/en-in/Windows7/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Call the helpline for the manufacturer of your network adapter. It is likely that neither Windows nor the router have problems, it's just a matter of getting the configuration on both put in place settings to work properly together. The manufacturer of the router will be the best resource to learn how to configure their device.

  http://www.TRENDnet.com/support/

  For more information, please see the following links:

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-a-network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

  Hope this helps

• My office wireless icon is x'd - cannot detect wireless networks.

  My computer screen suddenly went black this evening - the monitor was still, the fans were still humming, but it was totally insensitive.

  I forced a stop, and when I rebooted the computer, my wireless icon has been x'd out. My computer cannot detect wireless networks (there are a half-dozen or more in my building). I tried a good stop and restart, but the problem was still there.

  The Network Diagnostics tool told me to check the router, so I did--but all other devices in the House are connected very well. I thought it would be a malware, so I ran a MalwareBytes scan, which turned up nothing. Then I reinstalled the drivers from the card WLAN - no luck there.

  System Restore has not solved the problem. ipconfig says "media state: disconnected ' for my WIFI adapter, but I don't know how to fix this. In the devices, the Broadcom WLAN card Manager, he says "this device is functioning correctly.

  I work from home, so it is important that I can access my wireless. Help, please!

  Hello

  I imagine the inconvenience that you are experiencing.

  1. What is the brand and model of the computer network adapter?

  2. This error message with him modeling icon?

  3. do you have a code error message when you try to connect to the internet?

  Here are some steps you can follow to resolve the problem:

  Step 1:

  Check if the network adapter is enabled, if not, please go ahead and enable the network adapter. Please follow the steps:

  a. open network connections by clicking the Start button, then Control Panel. In the search box, type adapterand then, under center network and sharing, click view network connections.

  b. right click on the network card and do one of the following:

  -To disable the network adapter, click disable. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  -To enable the network adapter, click Activate. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, please see the link below:

  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-a-network-adapter

  Step 2:

  Try to reset the TCP/IP settings:

  Reference:

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357/en-us

  Step 3:

  Flush the DNS and request a new IP address of your ISP server by following these steps.a. Click Start
  b. click on run
  (c) in the Run dialog box type cmd.exe and click OK
  d. in the command prompt, type the following.e. ENTER after each new line.
  ipconfig/flushdns
  ipconfig/release
  ipconfig / renew
  output

  See also:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• Satellite T135D - cannot detect wireless networks

  I bought a T135D early January.
  Everything was happy until one day my laptop decides it cannot detect wireless networks, and even less to connect to one.
  I don't think the T135 came with a manual switch, while in the BIOS it says it's on.

  The graph with the antenna and 4 bars charge is no longer at startup, or the light that lights up on the front of my laptop. It's frustrating to have this kind of problem so early in the game with the T135D.

  Any help would be appreciated.

  Hello

  The wireless network must be activated by pressing the FN + F8 key combination.
  Have you tried that?

  If not, please check it

  Of course, you must make sure that the WLan card driver is always up to date.
  Here you can find the most recent:
  http://APS2.toshiba-tro.de/WLAN/

  Welcome them