SATELLINE Pro A200: When headphones are plugged in sound comes through the speakers + headphones

Similar Questions

• Audio comes through the speakers and headphones plugged headphones

  Audio sound plays through the headphons and speakers when headphones are connected.

  Any advice appreciated

  Hello again Nervuz,

  Thanks for the quick response!

  Based on the information you have provided, I recommend to uninstall and reinstall the audio driver for your desktop. To do this, please follow this document on follow-up with the IDT High Definition Audio Driverdownload and software uninstaller (Windows 8). If this does not work and you hear again audio to both the speakers and earphones, please follow the next step.

  The next step is to run a diagnostics using Automated Troubleshooting (Windows 8)program. This should help with the audio in question.

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• Sound comes through the speaker and headphones at the same time

  Why is the sound that passes through the speakers and the headphones simutaneouly?

  Hi MariaDuncan

   

  Are the headphones connected correctly?

  I suggest you refer to the link below and use the provided troubleshooting utility. Check if it lists and solves the problems-

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  I hope this helps.

• Skype comes through my headphones, but all other sounds come through my speakers on my laptop.

  I know there are a lot of discussions about this, but none of the solutions have worked for me. I can hear all the sounds on my helmet until all the sounds from Skype, music, that I would be listening out of my speakers up until Skype is quiet. It also occurs when someone calls me or I call them. It's really annoying please help.

  Please note that I've added some attatchments to illustrate some of the reasons why the other solutions did not work. My sound is divided between my speakers and the headphones and in Skype options it is no "headphones/speakers" as they are separated.

  
  

  Have you tried that?

  http://community.Skype.com/T5/Windows-desktop-client/Skype-audio-splits-to-both-headphones-and-speak...

• After XP downgrade, sound comes through the headphones and speakers

  Hi family Forum,.

  Recently, I've killed my dv2615nr Pavilion from Vista to Windows XP. Managed to install all the drivers and then followed the advice of CherylG (to whom I owe my ability to do something with this laptop, frankly) for the operation.

  My problem is that connect my headset does not cut the sound on my speakers.

  I tried reinstalling the drivers by following the advice of Cheryl G but it returns me to the same problem.

  Can someone help a newbie?

  @Kobby

  Your sound chip is Venice, that so difficult to find it running under XP,

  Try to use the related CherylG, modded by silver driver files almost a year, but replace this file WiSVHe5.inf

  Perform the same procedure to install it.

  Please, remind you that you need to Uninstall the driver before running all the new drivers, go to control panel, uninstall the audio driver from Add/Remove Programs, restart.

  If this mod does not work, try to use other models of HP that use chips from Venice, however, the pilot did not smartaudio ability.

  BTW, when he was to do Vista sound have smartaudio option in the Panel?

  These models are 520 HP and HP 530

  You can try to play with him, but my guess ports setting best are different.

  here

  FTP://ftp.HP.com/pub/SoftPaq/sp41501-42000/sp41836.exe

  You must manually extract and force it to run by using the Device Manager.

  The

• My iPhone think that my headphones are plugged when they are not if will not play music or alerts through the speakers. What should I do?

  My iPhone randomly started thinking my headphones are plugged when they are not. As a result, it won't play music or message/call alert through the speakers. What should I do?

  Try to push the helmet a few times to move the switch. If not, then please post something here and I'll be happy to help you further.

  AppleMan

• Always sound coming from the speakers when headphones are connected

  When I plug my headphones, the continuous sound coming out the speakers with no sound at all through the headset. When I go on manage audio devices, the helmet will appear, but it says that they're disconnected even if they are connected. I know the headset works very well because they work with my phone. I have Windows 8. What can I do?

  Hello. This is usually a driver problem, especially on models having Realtek audio.

  If you need more help please give the complete model name of the laptop.

• I "dragged" a folder of a drive on the DESKTOP so I could copy on a new disk. When they are copied to a new disk, the file is empty. The file is recoverable?

  I "dragged" a folder of a drive on the DESKTOP so I could copy on a new disk.  When they are copied to a new disk, the file is empty.  The file is recoverable?

  Hello

  You can try this program for recover data:

  http://www.Piriform.com/Recuva

  See you soon.

• Re: Satellite C660: Sound through the speakers when the headset is connected.

  I have a brand new 258 C660, running on Windows 7.
  Playback device: Realtek High Definition Audio

  * Whenever I have headphones or external speakers connected via the 3.5 mm jack plug, sound still comes through the built-in distant.*

  Here's what's happened so far:

  When I plugged the external speakers were first, I was asked to choose if I had plugged a headphone or speakers. I selected "speakers" and then also, perhaps foolishly, choose "do not ask me again".
  Now, I can't to this selection again.

  Here's what I've tried so far:
  -Reboot
  -Try different headphones, try them on other devices
  -System Restore (not, for some reason any)
  -all settings via the sound control panel

  Basically, I think that I am looking for a way to disable the internal ATAPI Jack when the external Jack 3.5 mm is used.

  I am aware, there was a similar thread some time ago, but the problem may be slightly different and perhaps due to the fact that I chose "do not ask me again". At least, I hope this isn't a hardware problem...
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=241409𺼁

  Thanks in advance for any advice

  Don t think there s hardware issue.

  Try this:
  Connect the headphones.
  Go to the control panel-> Sound-> playback tab
  Here, you should see the speakers and headphones.
  Now choose the headphones and set this default value.

  This help you?

• I can't hear sound in my headphones on my laptop but I can hear the sound through the speakers

  I have a laptop Toshiba A210, he has a lot of Windows Vista. When I watch a video and listen to the speakers I can hear it. But when I put my earphones in I cannot hear any sound. I went to control panel > sound > playback > in this screen the peripheral headphones appears as a disconnected device.

  I can not configure or test it and when I right click on it I can not set as default device.
  Help, please.

  Hello

  1 have had any changes made on the computer before the show?

  2. what happens when you try to set as default device?

  3. do you get an error message? If Yes, what is the full and exact error message?

  Method 1:

  I suggest you to make sure that the helmet is well plugged into the headphone jack.

  I also suggest you to test the issue with a different headset.

  Method 2:

  See the article and try to run the Troubleshooter:

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

• When I plug my headphones, the sound always pregnant. What should I do to get the sound to come through the headphones?

  I have a laptop HP with Windows 2007.  I can not access my helmet.  I have Plug and always sound speakers.  What I am doing wrong?

  Hello

  ·         The headset works on different computers?

  ·         When is - this problem started?

  Check if your headset is set to use as the default value * Communication * device instead of the default device, or if the two devices are configured by default. If so, do the default headphones, so that Windows will use only when they are connected to follow the steps below:

  Check volume settings.

  a. right click on the speaker icon in the taskbar, then select volume control options.

  b. put a check mark on "all devices evolving sound.

  c. make sure you have "Default uncontrolled communication device".

  d. place a check on the speakers and headphones.

  Also, follow the steps described in the following link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

• Tecra R850 - internal MIC does not work when earphones are plugged

  I factory reset my laptop yesterday and all since the internal mic only works when nothing is plugged into the Jack, including the headphones without a microphone and speakers. This was never a problem before resetting factory and I was able to plug in headphones to hear from people and can use the microphone to talk... now I can only talk to people when nothing is plugged in the sense that I have not heard from people on the speakers of the laptop...

  Any ideas guys? I don't want to have to buy new headphones :/

  See you soon

  It's really crazy. With the factory settings, everything should be OK.
  Theoretically, internal microphone can be blocked if you connect headphones into the microphone port.
  If please check al and don't forget your helmet is connected on the right audio output port.

• Restart problems with my Satellite Pro A200 when my dynadock is connected

  Help!

  I m a little frustrated when I try to restart or shut down to the bottom of my Satellite Pro A200 with my dynadock connection. I always turn off my 1st printer, as this used causes an error message, but the laptop crashes with the XP window...

  I have analog external (I know, anawhat?, but they work) speakers connected to the front, makes no difference whether they have or not. Drive external DRIVE is connected via USB2 port back and my LAN cable. I think I've tried everything, however continue to suffer Frost :)))

  Any ideas?

  Lot

  There may be some compatibility issues with your printer software and software dynadock
  Who knows. A thorough investigation would be necessary.

• 12.4.1.6 iTunes will not display my iPhone and iPad over wifi when they are plugged in

  Since I updated iTunes to 12.4.1.6 none of my devices, iPhones and iPads appear in iTunes when they are connected and the setting is correct, to synchronize this device via wifi. Any help would be great.

  Thank you

  iOS: device not recognized in iTunes

  see: http://support.Apple.com/kb/TS1591

• Win 7 Pro 32 bit time material plug unplug sound several times with no connection to install new

  Win 7 Pro 32-bit o/s, 3.06 ghz processor, 4 GB of RAM and nothing plugged in, clean and fresh install. There is a game repeated (constantly) connection / disconnected material 'sound' that repeats itself about every 6 seconds. There is nothing connected to the USB ports or something and that a single HD is connected and powered. There is no related tasks on demand for this activity, no programs are installed and no customization of what either just a new installation. I moved the HD to another PC and saw the same event. An another clean install of the o/s was the same. With or without additional programming, the problem is obvious.

  I've eliminated all services by toggle, but the sound continues its repetition. Event and error logs do not display anything.

  Please, comments or any souutions will be appreciated as soon as possible... Microsoft had no entry.

  All I can do to stop the sound to repeat is to turn off the sounds is select 'no sound' in the sound options.

  Hi KJ6I,

  You can check in Device Manager if there are unknown devices that are not getting detected.

  To open the device manager follow the link below.

  Open the Device Manager

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  In addition, scan for any change of hardware in Device Manager

  Open Device Manager, click Action, and then click on Search the hardware changes. Follow the instructions

  Now, restart the computer and check what is happening.

  Also see the wire that connects the hard drive to the computer, because this could be the reason for the sound.

  You also try to run a check disk to disk and let it repair.

  1. Click Start, type cmd in the start search box, right-click cmd.exe in the list programs and then click Run as administrator.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  2. at a command prompt, type the following command and press ENTER:

  CHKDSK X: /R

  Note: In this command, x is a placeholder that represents the drive letter of the volume you want to check.

  3. press y when you are prompted to check the drive the next time the system restarts.

  4. close all applications and restart the computer.

  Note: When you restart, Windows checks the drive for errors, and then Windows starts.

  5. after the computer restarts, repeat steps 1 through 4 for the other volume and try the backup operation again.

  For more information, follow the link below.

  Check a drive for errors

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.