Legs of connection using the Intel 4965AGN network card

Similar Questions

• Satellite A210 - 27 M (PSAELE) cannot use the new wireless network card

  Hi all

  I changed my wi - fi for Atheros AR5b91 and hardware network card is locked.
  I can't remove this lock of wi - fi switch or fn + F8 probably it's the lock of the bios.

  I tried to unlock it on Windows Vista, Windows 7, Ubuntu, so it is not caused by software.
  I tried the card WiFi on another laptop (toshiba not) and it's ok.

  If anyone can help?

  Thank you

  Hello

  To me, it seems that you used is not compatible Wlan module.
  But I found this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=79237

  A user was unable to activate new update Intel Wlan card.
  According to some information, its possible to enable the Wlan card by covering pin 13 on the wireless Mini-PCI network card.
  But to be honest I've ever tried and I would use this workaround with caution.

• Get rid of the current wireless network connection so that I can set up a new connection using the same IP address.

  Here's my problem: I got a new computer and a wireless network connection has been set up and I could get on the internet. My daughter then wanted to try her new computer and somehow his computer is defined as the network and I can no longer connect to the internet via my computer.

  The second part of my problem is that when I try to configure my computer, I get the message that I need to go to the Micro knowledge base and article 871122.
  I did it.  By following the instructions for Windows configure my wireless, I get as far as the stage of network connections - go to change the settings for this network connection.  It is said that I had to go to the wireless network tab.  There is no tab wireless network I can say to use Windows to configure my network connections...

  I know it is long, but can someone help.  I use Windows XP Prof 2002 with service pack 3 version. Thank you adpotate

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• Satellite A300 - code 31 with Intel 4965AGN network adapter

  Need help with an error code 31 of fixation with my Intel Wireless WiFi Link 4965AGN network card. I restored the PC from scratch and installed the drivers, but still have the same problem. I also have a 6 AX88772A USB 2.0 Fast Etherner Adapter as part of a Toshiba port replicator that works very well. I spent the registry of all errors.

  Any advice on what I could do to finally solve this problem?

  Hello

  What drivers you have reinstalled exactly? Normally if the 31 error code appears in the Device Manager, it should be enough to reinstall the driver only. You can find it here:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  You can install the driver if you go into Device Manager and select the WLAN card. Right-click on it and select Update driver. Don t forget to choose the Advanced installation where you can choose the driver yourself.

  Welcome them

• Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Why can't connect using Apple Airport WIFI of my remote security cameras but can connect using the Xfinity WIFI Modem/Router open?

  Two possibilities:

  (1) your airport WiFi might have a network name that is not in line with best practices, wireless

  A good wireless network name is...

  ... In short no more than 20 characters

  Simple... no special characters like an apostrophe, dollar sign, asterisk, etc.

  Compact, without spaces in the name

  For example, a wireless network network name as... red .dfedoryk Apple wireless network... .is not what you want. Something like... .dfedorykwireless. .. masse are much more likely to connect to non-Apple devices.

  Same guidelines your password

  (2) Apple gives the same name to network 2.4 GHz and 5 GHz network that produces double router band.  Some non-Apple devices are confused by the present, you may need to use the option to assign a different name for the network of 5 GHz on the router from Apple. Then, 'point' your device to the network name specific to which you want to connect.

• TCP/udp connection via the private wifi network

  I want to develop applications using the wireless private network with tcp/udp connection for my Blackberry 8320 (Version 4.2.2.180 without SIM), do I need authorisation from RIM so that they work in the unit? If it is true, how can I get permission?

  I noticed http://www.blackberryforums.com/wifi-hotzone/100800-8320-wi-fi-limited.html

  who says:

  "The Blackberry 8320 with wi - fi connection is limited. The only program that can use the wi - fi is the Blackberry browser... all the third-party programs... ie. Opera Mini, JiveTalk and even RIM's instant messaging programs. Yahoo Messenger, Windows Live Messenger, are all designed to connect using data from EDGE of the phone... None of them can detect or use the wi - fi! »

  If it is true now?

  You can use the interface = wifi parameter in the URL to specify that the connection should be performed by Wi - Fi.  However, please note that this setting is available in version 4.5.0 and highest BlackBerry device software.  Therefore, you must first put your BlackBerry handheld.  FURTER details can be found here:

  What - in different ways to establish an HTTP connection or socket
  Article number: DB-00396

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800451/800563/What_Is...

• Windows 7 does not connect to the new wifi networks

  I have a problem with connecting to wifi networks. My laptop only connect to wifi networks that I have already connected to in the past but does not connect to all nine. The computer will recognize the but won't give me the possibility to type in any password. For example, I can connect correctly to the House and my moms place as wifi passwords are already saved on my computer. However if I go to a friends house their wifi signal will appear but when I go to connect I will not have to enter a password, the mouse cursor will simply show it to load a few seconds and then nothing happens.

  Can someone help me?

  Hello James,.

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  This problem can occur for the following reasons:

  -WEP, WPA or WPA2 key or password security issues.
  -Incorrect network connection settings.
  -Corrupt or incompatible drivers.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If this does not help, then use method 2.

  Method 2:
  Please use the suggestions contained in this Microsoft support article and check the issue.
  Reference:
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Unable to connect to the internet, no network adapter icon?

  I received a computer toshiba satellite laptop which should have windows 7 ultimate on, however it does not connect to the internet wireless or ethernet, I lived all the troubleshooting suggestions, but there is no network adapter icon to activate. The laptop was of an elderly aunt who barely used and was not very tech savvy so I don't think that its been damaged (it has not been used for some time) any help would be greatly appreciated.

  Are there devices listed as "other"?

  If there is, run as 'Administrator' Device Manager and do a right click, properties, [pilot tab] and try to "roll back driver" (I guess the update driver will not work if the PC is not connected to the internet, but it can also be worth a try)

  If this does not work, try to force the hardware detection - http://www.pctips3000.com/how-to-scan-windows-7-computer-for-newly-attached-hardware/

  If still no joy, use another PC to go to the support site for the brand/model PC and download the latest driver available for your PC and the operating system network card (32/64 bit, etc.) and transfer it to the PC via a USB or SD card. Then try to install it.

  BIOS - how you access the BIOS will depend on the brand / model of the PC and the BIOS itself, but it gives an example: http://pcsupport.about.com/od/fixtheproblem/ht/accessbios.htm give it a read and see if you can follow. Ensure that you change and not change things randomly.

• I'm not able to open the properties and the State in Local (or all network devices) network. Actually I am not able to connect to the local area network connection in network and sharing Center.

  Connection to the local network - properties dialog box

  Hi, I'm not able to open the properties and the State in Local (or all network devices) network. Actually I am not able to connect to the local area network connection in network and sharing Center. But I can't access the Internet. My OS is Windows 7

  Hello Rajaneer,

  Is the computer that you are using a personal computer or a work computer?
  You will need to re - install your network card drivers like something was damaged and it prevents you to access the property:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• Multimedia file sharing only works if the two devices are connected using the same protocol

  So I'm frustrated!

  I spent an hour trying to get my Windows 7 computer to share my music with my XBox 360. I have two machines on my network, one connected by Ethernet to the router and the other connected by WiFi. I tried everything I could find online to get the WiFi connected machine appears in the "Music Player" on my XBox system - follow all sharing, make sure that my router has UPnP, restarted a bouquet of services, etc..
  Nothing! During this time, my machine connected to Ethernet was watching me in the face. He has appeared on the XBox without problem. I started to compare the settings on both machines and found no difference.
  Then I remembered, boredom, I had setting up WiFi sync for Windows Phone my wife. In fact, it was this session of troubleshooting that lead me to put this machine on the WiFi in the first place! Seems to set up WiFi sync, Windows Phone and the target of the machine must be, not only connected to the same network (obviously), but for some reason any the $ @$ crazy, both connected by WiFi. I just connected this computer by WiFi - not happy, a faster speed with my wired connection - and immediately fixed the problem itself.
  Then, remembering that, I moved my XBox WiFi network and - presto - my second machine appears without a problem.
  My question is... WTF! ???
  This is ridiculous - this is the same network! Why things must be connected using the same protocol?

  Hi, Edward Petersen,.

  Please contact the Microsoft community. I'll help you solve the problem with sharing music using media sharing.

  Some routers isolate the cable connections and wireless, you can check if you have the option in the configuration of the router to share media

  If the problem occurs, you can contact the router manufacturer for assistance.

  Hope this information helps. If you need help with Windows, simply reply that we will be happy

  to help you.

• Unable to connect using the current password

  Using the current password which only had 6 characters - have now changed to 8 hope if this helps solve the problem.
  Have you noticed too there was an update of Mozilla on my laptop the day before that this problem then this could be the reason?

  Unable to connect using the current password

  It is far from a complete problem description.
  Please explain in detail

  • what you were doing
  • That's happened

  Using the current password which only had 6 characters

  6 characters is a very weak password. Consider using a password manager to generate longer and more complex passwords and to remember these passwords.

• When a second (another) user tries to connect using the connection to distance that a message "select a user to disconnect so you can connect.

  Original title: Remote Desktop

  We have Windows Server 2012 essentials (evaluation version) installed and working.  When connecting to even via the remote desktop connection it works fine, but when a second (another) user tries to connect using the connection to remote, a message "select a user to disconnect so you can connect.  The names of the 2 users are displayed the first is the name of the administrator of the local server and the second is the remote desktop user who was first.  We need at least 3 to 4 remote desktop both users to be connected.  Please advice

  Hi BHARATISRANI,

  Thanks for posting in the Microsoft Community.

  Since you are using Windows Server 2012 Essentials, the question you posted would be better suited for COMPUTING public Pro on TechNet. I would recommend posting your query in the TechNet Forums to get help:

  Windows Server 2012 Essentials General TechNet Forums

• Connecting to the wrong wireless network.

  Nope.  Tried to make this process a few times just to make sure that I was just doing and still it connects to the wrong network.  Something else I could try?

  I'm in the boat the same, did you ever get a resolution on this?

  Separated from the<>https://answers.microsoft.com/en-us/windows/forum/windows_7-networking/connecting-to-the-wrong-wireless-network/633fcfd6-7bdd-4369-b66f-94611c5df76e >

  Here are some solutions to try if you can't connect to Wi - Fi. Follow the below mentioned steps to solve the problem:
  1 remove the network and let Windows re - find. Then enter the password again.
  http://Windows.Microsoft.com/en-in/Windows-8/get-online-tutorial
  2. change the TCP/IP settings, if the IP address is set to manual
  http://Windows.Microsoft.com/en-in/Windows/change-TCP-IP-settings#1TC=Windows-7
  3. If none of the above steps work, follow the link to solve the problem below:
  http://Windows.Microsoft.com/en-in/Windows/cant-connect-to-network#1TC=Windows-8

• Hello I can not connect using the camera Nikon D5 me please

  Hello I can not connect using the camera Nikon D5 me please :)))
  I've heard say that some work and I can not connect! Can someone help me to write on this topic?

  LR supports D5 attach now!

• After changing the orainventory place im unable to connect using the oracle user

  Hello

  IM using oracle 12 c on rhel 6 after correctly installing the software, I changed the location of oravinventory in/data/houses

  / u01/app/Oracle

  After making these changes im is no longer able to connect using the oracle user...

  also I back return changes I had made to the orainventory folder still unable to connect using the oracle user...

  any help on this would be greatly appreciated

  Sadia. wrote:

  Hello

  IM using oracle 12 c on rhel 6 after correctly installing the software, I changed the location of oravinventory in/data/houses

  / u01/app/Oracle

  After making these changes im is no longer able to connect using the oracle user...

  also I back return changes I had made to the orainventory folder still unable to connect using the oracle user...

  any help on this would be greatly appreciated

  Newer versions of oracle have implemented a great new technology to help solve problems, called "error messages."  Unfortunately, I can't find any reference to an error message named 'is no longer able to connect.

  And why you are moving your site from inventory?  When you have installed oracle, he put the inventory where he wanted.  There is no reason to try to change or replace.