Lightroom 5.6, white with preview display problem!

Similar Questions

• Why I get this message: Yahoo! Mail found the original e-mail, but met with some display problems. Please try again later?

  I have no ghostery but I still get this message. It has happened to these days.
  I can't answer or compose email yahoo with the firefox browser.

  I can receive emails yahoo in firefox, just can't answer for them.

  That must happen to be able to use firefox as I used for my yahoo email?

  I found that the problem for me was having my active AVG toolbar. I suspected that might be the problem since AVG recently had me update the toolbar. I disable to send an email and give the rest of the time. It's a pain, but significantly less pain that not knowing the question.

• display problem when start my Mac with Sierra

  When my MacBook Pro 13 with the retina display changes to another other than 1280 x 720 resolution, when I boot my Mac, there will be a white strip above the logo apple with flash on the screen... Is there a solution?

  Hello fish6,

  After reviewing your post, it sounds like you have problems with the resolution of the screen changes and the screen flashes.
  I would recommend you read this article, reset the NVRAM can help with the screen problems you encounter.
  

  How to reset the NVRAM on your Mac - Apple Support

  Thank you for using communities of Apple Support. Good day.

• I have a problem when using Google Maps, at a certain point my custards computer window and says there is a problem with the display drivers and he recovered, but it is not. Problem does not occur with Int Explorrer, so I don't think it's the computer

  When using google maps via Firefox, after asking a place which is not the General section of North America who comes up regularly, the firefox screen becomes white with a narrow banner at the top. A message appears in the lower right corner that says something on display drivers having had a problem, but now have been recovered. However, the display is not recover and the message of the banner is that Firefox is not responding. When I go to restart Firefox if I'm about to restore, the page is still frozen.
  I don't think there is a problem with my computer because it doesn't happen if I used to go to google maps, then G-cards works normally.
  This phenomenon didn't happen before the last update Google or Firefox. I used Fiefox for some years and also Google Maps on previous computers and on this one and not had it before.
  It is a relatively young computer (Asus EeSlate 121) less than a year. I have used Firefox since I bought it and until recently had no problem with Google Maps.

  I solved it myself, after the 'note' that was FF/Mozilla, just as I finished my message, commenting on what it was that my system was, I wnnt back to check my plug-ins, etc. I downloaded the latest Java, the TWO 32-bit AND 64-bit versions and latest Firefox.
  Now everything works.
  Thank you
  B.

• The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?

  The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?  There must be a display problem in the software.

  Have you of the 'show Talking Points' enabled in the view menu? Then you can see small white boxes superimposed on the image in the Viewer.

  

  You can enable or disable on / off power with ⌥F talking points.

• Display problem. The images have random black or white boxes that appear at different zoom levels. Picture is ok 100%

  I have recently updated my iMac last Adobe CC retina and now experience display problems. The images have random black or white boxes that appear at different zoom levels. Images ok 100% and some other levels of zoom.

  I've read other posts with the same questions.

  When Adobe gets out a fix, as this seems to be an error as Adobe making a lot of different HW platforms.

  Hi Martin,

  Please go to Preferences > Camera Raw and uncheck use display adapter. Click OK.

  Restart Photoshop and check for the issue.

  ~ UL

• Display of the PDF in preview handset problems

  I mainly work on Photoshop CS5.  All my work is it created.  My problem arises when it is create and watch a compressed PDF using "Preview" on the Macintosh.  The text is very funky.  But as expected, Acrobat itself displays all files without flaw.  My creation of PDF workflow is as follows.

  1. except Photoshop document (s) for individual of the Photoshop PDF, without diapers so I keep a single image and vector data. (I have always resize and save my documents in the intended use appropiately.  I keep all minimum file sizes when you create a document for the use of electronic mail.)

  2. with the help of Acrobat, I combine/merge my files, select the compression method suitable for the intended use (Small, Medium, Large)

  When I use the average compression in Acrobat, I encounter no problem through "Preview".  All of my text appears as it should.  Works fine, but I find myself with a 26 MB file.

  When I use the low compression in Acrobat (recommended for e-mail), I have all sorts of problems with my text in 'Preview '.  I use this option because my file sizes are half what they are in average compression.

  I know that "Preview" is not a replacement for Acrobat, but default Mac application for the opening of PDF files is "Preview", and many users that I deal with are not equipped with any Adobe software.  Is there a solution?  What is Acrobat when it compresses files for emailing?

  

  I would add that the small version that does not display the text always contains the text (I'm able to select), it is not visible.

  The problem no is not with what Acrobat is scrapped, but does seen Mac with available data. The problem is with preview. You can't have a scholarship of silk with the ear of the sow. If preview is doing a terrible job rendered pdf perfectly well, that the player will display properly, there is nothing that adobe can do.

• having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen that is 2 and a half inch thick green line appears and goes about a second.

  help someone?

  Thank you

  Howdy Yaser of zoysia,

  It seems that your screen displays some graphical anomalies when you connect to your user name. I would use these troubleshooting steps in the following article on the resolution of screens:

  Restart your Mac in safe mode to reset the default display resolution.

  If booting safe mode doesn't resolve the problem, reset your Mac NVRAM and SMC to reset the video ports on your Mac to their default values.

  From: get help with graphics issues on external displays connected to your Mac.

  Thank you for using communities of Apple Support.

• Display problems with the Portege R600 and Win 7

  I have a R600 running windows 7, every two minutes, I have a display problem where where the vertical pixels seem to get every centimeter unaligned, so my screen seems to blur digital in bars across it.

  I have an external monitor attached and get the same problem with or without him. I have tired the driver of toshiba and intel driver.

  It seems to go away if I have windows min and max, but sometimes it doesn't. If I run my mouse an affected area, that it seems in trouble and sometimes it's not all screen.

  A refresh solves it.

  Anyone have any ideas?

  > I have an external monitor attached and get the same problem with or without him.
  Maybe I m wrong but in most cases if these symptoms are seen on the two displays (internal & external) then a graphics chip could be affected
  It would be the worst case, because that would mean that the motherboard needs to be replaced

  But just a question; have you noticed that using the previous Windows OS preinstalled by maybe Toshiba (Win XP or Vista), you must install the image of Toshiba again to verify if this display problem is still visible

• A problem with the display in a form with a ScatterGraph

  Hi all!
   
  Now, I want to do an image that can be expanded outside and inside with the viewport in a form with a ScatterGraph window. I tried previously to do this picture as a backdrop, but the backgroundpicture cannot be zoomed with the display window. How can I solve this problem?

  Here is the picture:

  

  Or I have to calculate a large amout of points to sign on the coordination of xy without the image, and how can I register quickly because it takes a long time to calculate.

  Hello

  You can zoom/dΘplacer an image as well as the plot in charts. Here is a snippet of code showing how you can do it.

  Normal
  0

  fake
  fake
  fake

  EN-US
  X NONE
  X NONE

  MicrosoftInternetExplorer4

  / * Style definitions * /.
  table. MsoNormalTable
  {mso-style-name: "Table Normal";}
  MSO-knew-rowband-size: 0;
  MSO-knew-colband-size: 0;
  MSO-style - noshow:yes;
  MSO-style-priority: 99;
  MSO-style - qformat:yes;
  "mso-style-parent:" ";" "
  MSO-padding-alt: 0 to 5.4pt 0 to 5.4pt;
  MSO-para-margin-top: 0;
  MSO-para-margin-right: 0;
  MSO-para-margin-bottom: 10.0pt;
  MSO-para-margin-left: 0;
  line-height: 115%;
  MSO-pagination: widow-orphan;
  font-size: 11.0pt;
  font family: 'Calibri', 'sans-serif ';
  MSO-ascii-font-family: Calibri;
  MSO-ascii-theme-make: minor-latin;
  mso-fareast-font-family: "Times New Roman";
  mso-fareast-theme-make: minor-fareast.
  MSO-hansi-font-family: Calibri;
  MSO-hansi-theme-make: minor-latin ;}
  table. MsoTableGrid
  {mso-style-name: "Table Grid";}
  MSO-knew-rowband-size: 0;
  MSO-knew-colband-size: 0;
  MSO-style-priority: 59;
  MSO-style-unhide: no;
  black border: solid 1.0pt;
  MSO - border - themecolor:text1;
  MSO-border-alt: solid black .5pt;
  MSO - border - themecolor:text1;
  MSO-padding-alt: 0 to 5.4pt 0 to 5.4pt;
  MSO - border - black insideh:.5pt United.
  MSO-border-insideh - themecolor:text1;
  MSO - border - black insidev:.5pt United.
  MSO-border-information - themecolor:text1;
  MSO-para-margin: 0;
  MSO-para-margin-bottom: .0001pt;
  MSO-pagination: widow-orphan;
  font-size: 11.0pt;
  font family: 'Calibri', 'sans-serif ';
  MSO-ascii-font-family: Calibri;
  MSO-ascii-theme-make: minor-latin;
  MSO-hansi-font-family: Calibri;
  MSO-hansi-theme-make: minor-latin ;}

  Image img = Bitmap.FromFile ("myImage.jpg"); in pixels, this is the place where the image will be drawn RectangleF initialRectangle = Rectangle.Empty; in the data, to map coordinates the image XRange range; Range yRange; Private Sub PlotMyData() { plot your data here xData double [] = new double [] {3, 5, 7, 5, 8, 3, 7, 8, 2, 6}; Double] yData = new double [] {9, 1, 2, 6, 8, 3, 3, 6, 2, 2}; scatterGraph1.PlotXY (xData, yData); xRange and yRange define the plot area limits left-top to bottom-right xRange = new range (xAxis1.Range.Minimum, xAxis1.Range.Maximum); yRange = new range (yAxis1.Range.Minimum, yAxis1.Range.Maximum); RecalculateImageBounds(); } Simply map the data coordinates values in pixels posts from the top left and lower right must be mapped. Private Sub RecalculateImageBounds() { PointF size = scatterPlot1.MapDataPoint (scatterGraph1.PlotAreaBounds, (xRange.Maximum, yRange.Minimum); initialRectangle.Location = scatterPlot1.MapDataPoint (scatterGraph1.PlotAreaBounds, xRange.Minimum, yRange.Maximum); initialRectangle.Width = size. X - initialRectangle.Location.X; initialRectangle.Height = size. Y - initialRectangle.Location.Y; } Just draw the image. Private Sub scatterGraph1_BeforeDrawPlot (sender As object, BeforeDrawXYPlotEventArgs (e) { RecalculateImageBounds(); e.Graphics.DrawImage (img, initialRectangle.X, initialRectangle.Y, (initialRectangle.Width, initialRectangle.Height); }

  Make sure that the image is of good quality so that you can zoom in pretty close.

  I hope this helps.

• Display problems with all types of terrain and graphic

  Hello

  I have display problems general with all types of chart, graph or plot that I try to use, on two different machines, both with NVIDIA graphics cards.  A machine is a MacBook under XP SP2 in bootcamp and the other a Dell T3400 workstation (or something similar) under XP SP3.

  I posted this thread earlier which Ben replies to the weird graphic behavior.  Ben suggested that I try to simplify my code as much as possible while keeping the bad behavior and by submitting to the NC and the forum, because it is others have had problems of graph.  I tried, but in vain.  Display problem continues and continues and continues and then they just go and I can't get back by unscrewing the last stage of reduction or simplification of code.  But at some point during the reconstruction of the code, which I cannot determine, returns the bad behavior.

  So, I was set up with graphics looking for shit, until recently, when I thought I'd try some suggestions of other messages to a XY-plot function as a graph by creating a buffer and using nodes of ownership of land for the range control.  Things seemed promising, until my "XY table" started getting shit, too.  This time, the issue was with the grid lines becomes all chopped, attached images.

  I am out of resources here.  I think I'm running out of options to display graphic data in an acceptable manner.  Do I have to display data by using an Excel chart in an ActiveX container in Labview?  I'm not skilled enough to do it again.  I like Labview, it is the only programming language that I am competent even remotely help, but it's just inferiorating.

  Any suggestions would be much appreciated.  Thanks for reading.

  -Greg

  Greg,

  is there a particular reason why you use the bar plots - view superior graphic style? Try activating the legend of the plot, go to the bar plots and select the first track of the Bar Style. Your chart is displayed very well after that.

  See you soon,.

  Cerati

• Problems with the display of the 3D graph

  Hello world

  I use a 3-d chart in one of my screws and I have problems with the display. See what it shows by yourself:

  

  So, as you can see, the chart does not correctly display the data. But one thing I know, is that the data are sent correctly, because when I copy the LabVIEW graphic and paste it into paint, what I see, this is the graph displayed correctly:

  

  Anyone know what may cause the problem? I also have a similar problem with a waterfall in 3D.

  You can always download the updates of ni.com so.

  I also went through a documentation on known LV 2011 issues. I was able to find something interesting onthis page:

  3D image controls can display transparently or LabVIEW crash on some graphics cards

  The 3D Picture Control is based on an OpenSceneGraph that uses OpenGL. It was noted several reports of the 3D image control crashing LabVIEW. In almost all cases, it was an Intel graphics integrated into question. This accident is due to a mismatch of the graphic material. Note: most 3-d charts use the 3D picture control

  Some possible workarounds are:

  • Update the video driver
  • Enable/disable hardware acceleration
  • Enable Aero in Windows 7
  • Disable Aero in Windows 7

  I might try these workaround solutions and see if any of them work for you.

• Blue screen on startup... problem with the display driver?

  I have been using a Dell Inspiron 14R (N4110) laptop computer since 2010 without any problem.

  The laptop was purchased online from Dell and came with

  (1) Windows 7 Home Premium 64-bit and

  2) AMD Radeon HD 6470 M - 1 GB display card.

  Recently, I had a problem where my laptop just wouldn't start, showing the blue screen every time it tries to start. The blue screen mentions a problem with the file atikmpag.sys I understand is the driver for the AMD video card.

  If I delete/rename the files atikmpag.sys and atikmdag.sys (via secure boot mode) in C:/windows/system32/drivers, the laptop (not) start, but obviously does not recognize the graphics card.

  After a lot of unsuccessful trials debugging on mine (including trying to upgrade the drivers to display etc.)., I reinstalled the operating system and the drivers provided with the original kit (just to eliminate any possibility of an upgrade that went wrong). However, I still see the issue.

  That means there is a hardware problem? or a BIOS problem?

  Thank you

  R.B.

  Guys, the problem you describe is actually a hardware failure. There is nothing you can do except replace a motherboard for laptop, or taken some advanced technicians, COMPUTING which will replace or chip GPU reball.

  I have the same a laptop similar (Inspiron N5110), with the same problems and these problems - all started yesterday. Do not waste your time, just reinstall OS, then install display drivers, which are available on the official site of Support of DELL and after that - if it's not working, just do what I said.

  Generally these are consequences of an overheating laptop, but that it was certainly not my case (I did regular checks), I could even bet on chips quality GPU, which has been used in the manufacture of this model of laptop... again...

  UPDATE: Okay, last night was a long night for me and I can confirm finally - who's * chip AMD, which causes the blue screen, you mentioned. I disassembled my N5110 faulty, armed with a heatgun, Probe temperature (probe) and tons of aluminium + some flow of brazing, I made a fairly quick reflow and the result is just what I expected - everything works perfectly again, with the same configuration - even with the same installation of Windows, which has been to launch these blue screens. There are now no blue screen at all and portable computer performance as new.

  Apparently bad welding, when this laptop was manufactured, is the exact reason why we are where we are. The BGA chip was not dead at all (it was just poorly soldered). The same story, including HP and a bunch of other companies had some time ago with these NVIDIA chips (I know, some of you know what I'm talking about).

  CONCLUSION: Integrated DELL diagnostic software is useless against the detection of defects with a discreet graphics AMD card. Problem was not in the software or drivers - it was just a poorly welded chip (I regularly cleaned my laptop dust, so overheating is not an option here).

• "A problem with the display driver.

  Recently, I get an error message whenever I open Photoshop CS4. It reads as follows.

  "As Photoshop has encountered a problem with the display driver and has temporarily disabled GPU enhancements. Visit the Web site of the manufacturer of the video card for the latest version of the software.

  "GPU improvements can be enabled in the Performance preferences panel."

  I checked the graphics cards in Device Manager, and when I tried to update the software, it told me that I was aware.

  • OS: Vista Edition Home Premium
  • Dell Inspiron 1520
  • Display driver: NVIDIA GeForce 8400 M GS

  Sincerely, Danny

  Hello

  Try to update your display manually driver and do not use the analysis of the drivers on the manufacturer's website either.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system. For
  each driver in the list, additional useful information is displayed: load address of the driver, description,.
  version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• Major display problem with Audition CS5.5 on Surface Pro 4 Tablet

  Hi people,

  I just got a new Microsoft Surface Pro 4 tablet, so I can edit on the go more easily than with my old laptop. I use Audition CS5.5, because I am a podcaster and radio producer, and it works wonderfully for these tasks. Unfortunately, when I installed hearing on this new tablet, I discovered a major compatibility issue. All text and buttons display so small that the program is essentially unusable.

  

  I tried to play with the display settings on the Surface, but they seem to have no effect on hearing. Even when I get the settings "change the size of the text, apps and other elements ' maximum, it has no effect on how the hearing poster (even if she handicap other programs).

  

  So I tried contacting Adobe via Facebook, and everything they said it was "Hi Chris, see if this article helps you to: . http://bit.LY/24jts28 "Thanks , ^ KM. Which I linked to an article from Microsoft. When I went through the troubleshooting process, however, he suggested 1) the same thing, I tried 2) communicating with Adobe or 3) buy the new version of the hearing.

  

  And earlier I tried calling technical support and they told me that they don't offer phone support for tablets.

  I am extremely frustrated. I love this piece of software and it would be ridiculous to pay a monthly subscription for the new version just change the display settings. Was Adobe really this careless with the design of this product, and they have now abandoned it? What can I do to solve this problem?

  Thanks for any help.

  -Chris

  Support should not consider the 4 Surface Pro tablet, from a support perspective, it's a PC.  I'm sorry to hear that you who were respected.

  Richard is correct, in CS5.5 we simply don't HiDPI screens on the piece of road, and you will probably find that's true with many Adobe applications since that time.

  In addition, as Richard has pointed out, in recent versions we did some work to support HiDPI screens as well as some of the capabilities of the touch Surface.  Here are two tweets I sent to a customer showing on my personal 3 Surface Pro:

  C Van Winkle on Twitter: "@DawsAngeles @duringleaves https://t.co/owizvYIbg0".

  C Van Winkle on Twitter: "@DawsAngeles @duringleaves https://t.co/Zw3NI41rMG".