LRT224 Problem with PPPoE

Similar Questions

• Problems with wireless on WRT54GS

  After a power outage, I had to update the info on my WRT54GS router.  It works fine until I have try to configure the wireless part.  After I put a WEP key and save the settings, the "Manage settings" screen.  When I click on 'Continue', the router is basically dies.  The address bar has http://192.168.1.1/WL_WPATable.asp.  At this point, the only option I have is to power and on the router that allows to restore access to internet on the wired devices, but no wireless internet access.  Is there a table is messed up?  How to get this resolved in addition to become another router?

  Tried your suggestion, nothing is.  Finally, I changed my bridged AT & T of PPPoE to Ethernet router and set the router Linksys (Cisco) PPPoE with my AT & T username and the password.  It took care of the problem with the Wi - Fi.  I had questioned the AT & T Rep on PPPoE configuration and he assured me that AT & T has made this change and this also works with the router assign PPPoE.  Guess he was wrong.  But I am now happy.

• Problem with WRT160NL

  I bought a WRT160NL a week ago, it worked fine until now.

  I am connected via the net with a PPPoE connection. I set up the router to stay connected all the time to the internet and yesterdy I noticed that my download speed was very low so I have powerd OFF and on again. When he returned to the life he connected himself but the DHCP stoped working. I use windows 7 and in the cone right it says that I'm connected to the netowork but no internet available...

  I zero it to it's the factory settings and reconfigured it back. Now it works again, but in a few days my Torrent speed will come down to MB kb and must get back to factory settings... it's not good ...

  I tried to connect to the net only when internet is necessary, but after a computer is restarted the same problem appears.

  What is the problem with it? Why fall the DHCP?

  Try upgrading/re-Flash the firmware of the router.

  Connect the computer to the router with the Ethernet cable. Download the latest firmware from the site Web of Linksys and save it to your computer.

  Open the router configuration page and go to the tab Administration on Firmware Upgrade tab browse the firmware file that you have already downloaded and update on your router.

  After upgrading the firmware of your router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 30 seconds. Power cycle the router and then reconfigure.

• Strange problem with WRT54GS 7.2

  Hello

  I have a weird problem with my v 7.2 WRT54GS router.

  I use a unique identifier SSID and everytime I try to connect to the wireless network, I am only able to connect locally - I can't access anything other than what is on my local network.

  However, if I plug in a cable to the router and my PC, I am able to access the internet, but ONLY if I am also connected to wireless "local only".

  Earlier, on another PC, I was able to connect to the wireless network (local only), then set up a connection high steady flow as you would with an ethernet cable and connect to the internet, even if a cable is plugged into my PC.

  So, I confirmed that the router emits a signal that can be used to access the internet, but it must be done in a very complicated way.

  Anyone know anything about this? Help is appreciated.  (I already tried upgrading to the latest firmware)

  If your Modem is already configured in Bridge Mode... So you can do is: connect the Modem to the Internet Port Linksys router and then connect your computer to the router Linksys on the Port No. 1.

  Connect to the Setup page of the router and below installation "Internet Connection Type" PPPoE and enter the username and password provided in your by your ISP and below check the box 'Keep Alive' and click on save settings...

  Then click on the 'status' and check the IP address of the Internet... If you are able to see any IP address... Then check if you are online for your wired computer...

• I have problems with connecting by Modem DSL Siemens SpeedStream 4100.

  I have a little problem with my modem. I have a strange situation in which my internet goes several times a day (about 50-200 a day / every 10-15 min). I can't find the answer as to why this happens, however I noticed that whenever I get a phone call, my internet will. So that I get my signal back I have to make a phone call, so I just call my house to get a busy tone. My internet will come back without a doubt, but I don't think it's fair to make this happen. What could be the reason for these problems and how I could fix them? I have a PPPoE Setup so I am connected through a router, however, this problem happened a long time ago (I don't remember if it is since I have the modem). I'm in a laptop, but the question that's happened since a direct link between the modem and my desktop via cable Ethernet.

  Its been years and I have still not found a reason as why it happens. I know several people who have the same problems as me, and I would like to have days when my internet doesn't go away every 10-20 minutes. Any suggestions why this is happening or how to fix?

  Thanks, best regards

  Paul Zapata

  http://en.kioskea.NET/forum/affich-19259-router-disconects-when-phone-gets-used

  Read the above.

  Do you use a junction box on the phone, including extensions of each phone?

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Here are the General news when Internet is de-energized;

  Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• Problem with ping VPN cisco 877

  Hi all!

  I have a working VPN between a fortigate and a Cisco.

  I have a problem with ping network behind the cisco of the network behind the forti.

  When I ping to vlan2 cisco without problem (192.168.252.1) interface, but I can't ping a server in the vlan2 (192.168.252.2) behind the cisco.

  However the Cisco I can ping the server. In the forti, I see that ping to the interface vlan2 and server in vlan2 take in the same way, and I can see package.

  I post my config could see it it as blocking the ping from 10.41.2.36 to 192.168.252.2 while 192.168.252.1 ping is OK?

  IPSEC #show run
  Building configuration...

  Current configuration: 3302 bytes
  !
  ! Last modification of the configuration at 14:42:17 CEDT Friday, June 25, 2010
  ! NVRAM config update at 14:42:23 CEDT Friday, June 25, 2010
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime localtime show-time zone
  encryption password service
  !
  IPSEC host name
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 1000000
  enable secret 5 abdellah
  !
  No aaa new-model
  clock timezone GMT 1
  clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
  !
  !
  dot11 syslog
  IP cef
  No dhcp use connected vrf ip
  DHCP excluded-address IP 192.168.254.0 192.168.254.99
  DHCP excluded-address IP 192.168.254.128 192.168.254.255
  !
  IP dhcp DHCP pool
  network 192.168.254.0 255.255.255.0
  router by default - 192.168.254.254
  Server DNS A.A.A.A B.B.B.B
  !
  !
  no ip domain search
  name of the IP-server A.A.A.A
  name of the IP-server B.B.B.B
  !
  !
  !
  !
  !
  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 5
  ISAKMP crypto key ciscokey address IP_forti
  !
  !
  Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpntest
  !
  myvpn 10 ipsec-isakmp crypto map
  defined by peer IP_forti
  Set transform-set vpntest
  match address 101
  !
  Archives
  The config log
  hidekeys
  !
  !
  !
  !
  !
  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto
  !
  ATM0 interface
  bandwidth 320
  no ip address
  load-interval 30
  No atm ilmi-keepalive
  DSL-automatic operation mode
  !
  point-to-point interface ATM0.1
  MTU 1492
  bandwidth 160
  PVC 8/35
  VBR - nrt 160 160
  PPPoE-client dial-pool-number 1
  !
  !
  interface FastEthernet0
  switchport access vlan 2
  !
  interface FastEthernet1
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  switchport access vlan 2
  !
  interface Vlan1
  IP 192.168.20.253 255.255.255.0
  IP nat inside
  no ip virtual-reassembly
  !
  interface Vlan2
  IP 192.168.252.1 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface Dialer0
  bandwidth 128
  the negotiated IP address
  NAT outside IP
  no ip virtual-reassembly
  encapsulation ppp
  load-interval 30
  Dialer pool 1
  Dialer-Group 1
  KeepAlive 1 2
  Authentication callin PPP chap Protocol
  PPP chap hostname [email protected] / * /
  PPP chap password 7 abdelkrim
  myvpn card crypto
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 Dialer0
  IP route 10.41.2.32 Tunnel0 255.255.255.240
  !
  no ip address of the http server
  no ip http secure server
  The dns server IP
  translation of nat IP tcp-timeout 5400
  no ip nat service sip 5060 udp port
  overload of IP nat inside source list NAT interface Dialer0
  !
  IP access-list standard BROADCAST
  permit of 0.0.0.0
  deny all
  !
  NAT extended IP access list
  IP enable any host IP_cisco
  deny ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  !
  access-list 101 permit ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
  public RO SNMP-server community
  3 RW 99 SNMP-server community
  SNMP-server community a RO
  SNMP-Server RO community oneCommunityRead
  not run cdp
  !
  !
  !
  control plan
  !
  !
  Line con 0
  password 7 abdelkrim
  opening of session
  no activation of the modem
  line to 0
  line vty 0 4
  password 7 aaaaa
  opening of session
  escape character 5
  !
  max-task-time 5000 Planner
  NTP-period clock 17175037
  Server NTP B.B.B.B
  Server NTP A.A.A.A

  end

  Alex,

  It's your GRE tunnel:

  interface Tunnel0
  IP 2.2.2.1 255.255.255.252
  source of Dialer0 tunnel
  destination of IP_forti tunnel
  myvpn card crypto

  You also have routing set by it.

  You don't need a GRE tunnel, nor do you need the road to tunnel if you want just IPsec tunnel.

• problems with, phone, 6, Bluetooth kit, Nissan, after update, for, Rios, 1.0.2

  After the update to ios 10.0.2 - trying to use bluetooth to call my vehicle, it says: "this article is not in your phone book." How can I solve this problem?

  Greetings, joybelino1!

  Thank you for joining the communities Support from Apple! I can't wait to see that you are having problems with your Bluetooth in your car! The good news is that Apple has a great article that will help you with measures to try to resolve the problem. Read this article to gethelp to connect your iPhone, iPad, or iPod touch with your car radio. Even though he talks about problems with the connection, it also has the steps for other questions you may have once connected.
  
  

  If you use Bluetooth

  1. Consult the user manual of your car stereo to get the procedure to a Bluetooth device.
  2. On your iOS device, drag up to open Control Center, then press ontwice to turn on Bluetooth and turn it back on.
  3. Restart your iOS device.
  4. On your iOS device, Cancel the twinning of your car radio. On the screen of your car désapparier your iOS device and any other device. Restart your car and your iOS device, then pair and connect again.
  5. Update your iOS device.
  6. Install the updates to the firmware of your car radio.
  7. If you still not connect, contact Apple technical support.

  Have a great day!

• Anyone having problems with WiFi connectivity after upgrade to Sierra?

  I was wondering if anyone else knows issues with WiFi connectivity since the upgrade to Sierra 10.12? I have not had any problems with connectivity WiFi previously on El Capitan. Now I have regular randomly loose connectivity. My internet is cable and when it is connected I have a 100% connection. My details of iMac and I have used only 10% of my storage.

  

  No problem with my iphone 6.

  Hello AspDesigns,

  I understand that, since the upgrade to Mac OS Sierra, your Mac seems to have trouble staying connected to Wi - Fi. Fortunately the diagnosis built-in wireless can help identify the source of so much trouble.

  Search for Wi - Fi using your Mac problems

  See you soon!

• Problems with mail after switching to macOS Sierra

  Hey all

  After having recently upgraded to macOS Sierra, I am unable to read my mail.

  I get the following error every time I check on "Get Mail".

  There may be a problem with the mail server or the network. Check the account settings "*" or try again.

  The server returned the error: Mail could not connect to the server 'pop1.tribcsp.com' using SSL on the default ports. Verify that this server supports SSL and that your account settings are correct.

  What does this error message mean and how can I solve this problem.

  Thank you

  Hi Michael,

  I see your message that you get an error in the mail indicating that there is a problem with the mail server or the network.  To help get this problem resolved, I suggest that you follow the steps below:
  

  If mail refers to a problem with the mail server, or the network

  Mail will say that it is impossible to connect due to a problem with the mail server or the network. For example, the message may refer to a connection that has expired, or too many simultaneous connections:

  

  If you are connected to the Internet, but the connection has expired, your email provider might be affected by a discontinuance of service. Contact them or see their status Web page to ensure that their e-mail service is online. Examples of status pages:

  • iCloud mail status
  • Gmail status
  • Status of Yahoo mail
  • Status of the AOL mail
  • Status of Outlook e-mail

  If the message indicates the number of simultaneous connections, too many of your devices is check your e-mail account at the same time. Quit Mail on one or more of your other devices.

  If you are still unable to send or receive e-mails

  1. Make sure that you have installed latest version of the Mac software updates, especially if the problem occurred immediately after the installation of a previous update.
  2. In OS X El Capitan or later version, you can see a status icon and the short error message in the upper right of the Mail window, under the search box. The message may indicate 'Network offline' or 'Connection failed', for example. Click the message to see more details on the issue.
     
  3. Check your connection to the Mail connection doctor. It might be able to say more on the issue.

  If you cannot send or receive e-mail on your Mac.

  Take care.

• iMac 27 "mid-2011 - Intermittent problem with CPU fan running at full speed and sleep mode.

  Hello!

  My iMac 27 "has an intermittent problem with the CPU fan runs at full speed. Sometimes it happens at the time when I start it, sometimes only in my session, and sometimes only after a certain time. So does seem to be a problem of "heating".

  Second issue is with the mode 'sleep'. It may occur also at any time, at the start of the iMac, session, or after a certain time. But once he starts to go in mode 'sleep', when I wake up, it goes right back in mode after a few seconds and that it will continue indefinitely until I restart the computer.

  What could be?

  Please help me!

  4ntoine

  Here is my model of iMac:

  iMac 27 "mid-2011 model 12.2

  Intel Core i7 3.4 GHz

  AMD Radeon HD 6970M 1024 MB

  OS X El Capitan 10.11.6
  SMC 1.72f2

  Boot ROM IM121.0047.B23

  reset the SMC

  Reset the management system (SCM) controller on your Mac - Apple Support

• problem with playing the clash of clans

  I'm having some problems while playing the clash of clans on my 2 mini ipad screen does not seem to meet sometimes as if it was some sort of delay so I have to tap several times in order to use a filter or throw the troops on the battlefield.

  Hi Trinitygr,

  Thanks for posting in the Community Support from Apple! I understand that you are having problems with your iPad screen while playing a game. I like to play games on my iPad and I don't see how this could be a nuisance. I'm happy to offer assistance.

  Are you only had this problem when using the app clash of Clans, or does it happen in all applications? I recommend to start by following the steps described in this article:
  If an application you have installed unexpectedly closes, unresponsive, or does not open

  Take care!

• I'm having problems with an outdated Apple ID

  I have problems with updating Apps etc in my Apple account because he always asked an obsolete in sign.  How can I change this?

  Hello

  Go down to itunes apple ID Delete page homepage all ID and then add it back back.

  See you soon

  Brian

• Anyone having problems with the new iPhone LTE connection 7 on Verizon?

  I am now on my iPhone second 7 with Verizon. I had four phones for me and my family. I have now had issues where I have no signal in the same areas where my signal allows to be strong. I can't solve the problem with the activation/deactivation of the airplane and then mode again in normal mode. My phone will rest with no signal for 5 minutes, then going to LTE with three bars. I also had the problem where I had only 1 x signal, while my son standing right next to me has LTE. And he had the same questions, where I'm on LTE and it gets no signal. I use to have LTE where I live and work all the time, now it's spotty at best. Apple has replaced me and my sons iPhones but not luck. Still do. Any ideas or an any other suffering?

  (1) go to settings/cell phone/cellular data Options/enable LTE and select ONLY the DATA. This seems to solve the problem (as a temporary solution) for most of the people affected by this problem. The bad part is your request might not be as clear (since they cannot use the highest LTE signals) and you can make calls and data at the same time. But it does not solve the issue.

  (2) there are rumors (but you didn't hear that from me that we only are not supposed to discuss beta software program Apple in this forum) that the new version of Apple Beta for iOS (which also includes an update of the software carrier Verizon to 26.0) seems to solve this problem. So, there's a light at the end of the tunnel.

• Problem with some fonts of symbols after the installation of the Sierra

  Hello

  I have recently upgraded the OS on my iMac late 2012 for Sierra, since doing so, I noticed a problem with several fonts.

  All symbolic symbols Apple to Wingdings fonts not correctly displayed in the font book. Apple symbols looks like a standard wheelbase of san, and other symbolic fonts just show as question marks '?' where the images should be.

  In text editing, that I can't even see the symbolic fonts like Zapf Dingbats and Wingdings in the selector. However, they all work well in Adobe Illustrator (CS5) and Microsoft Word 2011. Apple symbols still looks like a standard font.

  I already tried the following:

  1. check the fonts in font book

  2 fix the duplicates in the font book

  3. using the "Restore Standard fonts" option in the font book

  4 deleting a file in the folder Preferences plist Fonts

  5 deleted the cache of police and the database

  I'm out of ideas. Has anyone else had the same problem found a fix?

  Kind regards

  Greville

  I'm just to add that I used the recovery partition to do a clean install of Sierra on a hard drive external and then booted into it to see if it had the same problem.

  And he does. Wingdings and other photo fonts appear as '?' in boxes where the letters must be in the font book.

  So this seems like a problem with the way Sierra displays these fonts, not with the font files themselves.

• ios10 problem with non-users of iphone messaging

  After upgrading my iPhone 6 ios10, I had intermittent problems with the messaging of Android users (basically, the conversations no iMessage). In about 60% of the time it is not just to deliver the message no matter what I do (pressing the 'Try Again' don't work do not). He has no problem with the reception of the texts, but I can't answer to Android users (Interestingly, I can message users of Android if they are in a group with iPhone users text). I tried everything was updated to the last verision until reset of ios everything.

  I can't find anything online about this. I'm the only one who what?

  Group Messaging uses the MMS. Normal text messages using SMS. SMS uses the voice channel to transfer messages and is strictly a basic function. If you are experiencing problems sending SMS, contact your carrier.