[MAC: InDesign CS4] IP address of the router

Similar Questions

• When you set the IP address of the router, WRT160N Inaccessible

  Hello

  I bought a WRT160N router yesterday and eagerly tried to connect my laptop to the internet (ADSL) modem using this router. As my ADSL modem is a router DHCP too, and I want to keep it like that, I have it plugged in ethernet cable form one of my ADSL modem/router, LAN ports in one of the LAN ports on the modem, Linksys have the Linksys operating as a bridge. However when I tried to specify an address of router static IP (192.168.1.254) in the basic parameters of configuration Linksys Panel, disabled the DHCP setting and saved, I could not connect to the router more using this new IP address - my browser tells me that the Web page doesn't seem to exist, but it cannot establish a connection with her. Then I have to reset the router in order to access configuration panels using the default address 192.168.1.1. Is there a reason why I cannot access the control panels of the router with the new IP address of the router that I've specified?

  Thanks for any help,

  Hello

  the problem is resolved, be it in a different way. I tried your trick to wait 30 seconds after the registration and the recycling of the modem, but this had no effect. What helped does not change the settings for address IP Routerl and the setting from the DHCP server on the router for the disabled at the same time. If I only changed the setting to the IP address of the router and recorded, the modem has been reset automatically and starts with the new correct router address. After that I changed the setting of DHCP server to the WRTN160 to off and then I was able to get the router working, like I wanted.

  I assume that when you connect the router to a computer reset (after taking out the IP address of the computer) with DHCP from the active router, the router assigns an IP address to the computer that somehow interferes with the local IP address parameter, if you define that at the same time.

  In any case, all work now, and I have excellent signal everywhere in the House. I guess that congratulations go to me :-) but still thanks to eliminate one possible cause of the problem

  Kind regards

  Gerard

• Registry files have been deleted via a Norton 360 3.0 registry clean up - can't get an ip address from the router

  I'm running Vista Ultimate, -connection (Ethernet) with Verizon FIOS I ran a Norton registry clean and foolishly trust what he says to remove.

  At first, all of my USB cards have been screwed up (noted in the Device Manager with exclamation next to each one points)
  I did a system restore and that corrects this problem, but now I'm having a problem with my network card.
  , All diagnostic tests, etc. show that the material is very good. My router is also fine the problem is that windows can't get an IP address from the router and then assigns his own
  (a # 169 instead of a # 192)
  In the network connection properties, it says that the device is functioning correctly, and the driver is up-to-date.
  'Connection speed' tab: a window of diagnosstics is: I ran testto test adapters connect to connect to the network.
  Results: connection Test
  Test details:

  I have "this card is configured to obtain an IP address automatically. No DHCP server is present on the network. Windows selected an IP address by using the alternative private IP addressing. »

  X "Ping 0.0.0.0 Gateway: failure.
  !  "No DNS server is available for this connection.
  ! "No WINS server is available for this computer.
  X "Ping 0.0.0.0 network: failure.
  ------------------- -------------------------------------------------------------------------------------------------------------
  In this same window of diagnostics under the "LinksTab".
  Link current test status: (what is determine the current connection speed of the adapter and link partner)
  Results:
  ! The adapter is configured to negotiate the speed with the link partner, but 1000 Mbps was chosen as one of the possible speeds.

  The best link options-results of the speed test:
  ! Could not detect way reliable speed and duplex settings. Possible speed/duplex settings are 100 Mbps Full Duplex and Half Duplex 100.
  (Note that these link tests are online and I can't online)

  Also in the Diagnostics window-under the 'Cable' link cable - past-polarity is normal.
  Depending on the tab is the Hardware tab
  Hardware diagnostics check for I/O conflicts...
  Results: all the tests:
  EEPROM test
  FIFO test
  Test register
  Interruption of the tests
  Loopback test

  I also went in the prompt type in IPCONFIG... c which shows:
  Ethernet connection to the Local network card:
  ConnectionSpecific DNS suffix: (it's completely empty here)
  Link-local IPv6 address: fe80::bda9:951 d: 619f:a0dc 9%
  Autoconfiguration IPv4 address: 169.254.160.220
  Subnet mask: 255.255.0.0
  Default Gateway: 0.0.0.0

  I also have a sort of ping command here-cant remember the command, but the results were in the CBS... I didn't know how to reach. He however escape from something on the registry files.

  I went throughD-Link Tech router (router) support is good, Fios Tech support everything set up right, - Norton support(Norton denies that the files were not to be touched-although their report shows these registry files were deleted)-Dell Tech support because my warranty missed 3 weeks ago - although I still have the "your Tech Support team until 2013 - which is valid only if you have a hardware warranty-made no sense sold me the car without. the engine - directed the FTC to bring a complaint about it - after I get this fixed number.

  I hope someone can help... by the way I get perfectly in line with my laptop - I know this isn't my router. I'm sure it's due to some registry files being moved-(j'ai eu deles de messages d'erreur indiquant que les fichiers de Registre ont été endommagées ou manquantes) what do I do now? No system restore to restore this part of the register - I also installed the drivers from the dell drivers and Utilities disc - but maybe I've done that correctly? I put the disc - extract files-(he says they have been unpacked) was a new step for me to do after that? Help, please!
  Thank you!

  Hello
   
  We recommend that you install the router (see its manual) and the pilot of NIC once more and check the difference. In the first post, you mentioned that you decompressed or extracted files. Once the files are extracted, you will be asked to install the driver. However if you do not receive any prompts for the driver, then you will need to locate the destination folder where the files are checked to find the configuration file.
  
  Open the destination folder where the files are extracted and run the Setup file to complete the installation.
   
  To download and install the latest network card driver, visit the site Web of the manufacturer of the device or system.
   
  For more information on downloading and installing the drivers, visit this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/the-hunt-for-drivers-how-to-find-Windows-Vista-drivers-for-all-your-hardware
   
  I hope this helps.
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• How to find the IP address of the router from my computer in Windows 7?

  What is the best way to find the IP address of the router from my computer in Windows 7? I know not how to make using the start > cmd > ipconfig, but is there a way to do it with just the mouse?

  Right click on the WiFi icon or-> LAN in the system tray click on open network and sharing Center-> click on "Wireless network connection"--> details click-> see item highlighted on the screenshot:

  

• My printer Photosmart D100a wireless continues to change the IP address when the router reboots.

  My printer Photosmart D100a wireless continues to change the IP address when the router reboots.

  Another idea is to unnstall HP software (using its uninstall program), then restart your PC.  Finally, download the latest version of the software for your printer from the "Support & drivers" link at the top of this page.

  Meanwhile, keep your antivirus operational.  The installer configure it for you during the installation of the printer.

• Retrieve the external IP address of the router from a paralytic

  Hello

  I'm working on a workflow, that the provisions, a complete paralytic, I have nearly all that work, the only issue I am running into is not able to shoot/get the external IP address of the router once that vApp is put into service. Does anyone know which API can I gives the floor to get that information? I have attached a screenshot of the NAT tab in the firewall of vApp to give more details on the specific element, I'm trying to recover. Any help would be greatly appreciated.

  Thank you

  J

  Here's an excerpt from one of my workflows in test I use to inspect a vApp on vCloud Director with vCO 5.5 5.5:

  System.log("=== Network Configurations ===");
  var networkConfigurations = vApp.getVappNetworkConfigurations();
  for each (cfg in networkConfigurations){
      System.log("href: "+cfg.href);
      System.log("Description: "+cfg.description);
      System.log("isDeployed: "+cfg.isDeployed);
      var netConfig = cfg.configuration;
      System.log("ipScope: "+netConfig.ipScope);
      var routerInfo = netConfig.routerInfo;
      if (routerInfo != null){
          System.log("External IP: "+routerInfo.externalIp);
      }
  }
  

  I would like to know if this is useful, I just double it checked by running against one of my vApps has a similar configuration (NAT and Port Forwarding) and it displays the correct external IP address for me.

  [2014-02-18 11:41:33.514] [I] === Network Configurations ===
  [2014-02-18 11:41:33.515] [I] href: null
  [2014-02-18 11:41:33.515] [I] Description: This is a special place-holder used for disconnected network interfaces.
  [2014-02-18 11:41:33.515] [I] isDeployed: false
  [2014-02-18 11:41:33.515] [I] ipScope: null
  [2014-02-18 11:41:33.516] [I] href: null
  [2014-02-18 11:41:33.516] [I] Description:
  [2014-02-18 11:41:33.516] [I] isDeployed: true
  [2014-02-18 11:41:33.516] [I] ipScope: null
  [2014-02-18 11:41:33.516] [I] External IP: 192.168.1.61
  

  

• HP Officejet Pro 8610: Try to install the full software concludes printer, but the IP address is the address of the router, not the printer

  I tried several times to remove printer, uninstall the drivers, reboot, reset the printer to the factory, etc. without success.  I even went into the registry and deleted the printer reference as much as I could.

  Please note I know how to connect the wireless printer and did successfully to the router with IP 192.168.1.108.   The problem is that the installer will search for a printer on the network and detects the 8610, but it appears with the IP address 192.168.1.1, which, of course, fails to install correctly.

  How can I get the dialog box to see the printer with the CORRECT IP ADDRESS?

  Well, I gave up trying to connect wireless and connected the printer with an ethernet cable.    Re-installed software that went much smoother, but still showed printer with IP router when you try to add it.   I chose "other devices" and is manually entered IP ethernet.

  Everything works now, including scanning.

  I think that the new router (for satellite internet) blocking a port that is required to complete the driver installation.   I had to add a switch to have an additional ethernet port to connect the printer.

  It was NOT a good experience.   I had a lot of practice of deleting, downloading, installation, configuration of the HP printer again and again well, therefore perhaps not all a lost cause.

• Equium A200: Unable to connect to the Wlan - no IP address of the router

  Dear readers

  I have a laptop Equium A200 Toshiba.
  I TI a year, a little more of it and it did work under Vista perfectly, no problem.

  First of a sudded 4 weeks ago my wife told me that she can no longer connect to the internet.
  I thought that it was something less serious, until I couldn't solve the problem.

  The laptop is not receiving an IP address wireless or cable modem.
  I type cmd and I get an IP starting with 169 in wireless and wireed cases.
  I also tried to reset the NETWORK card, but it does not work.

  It's frustrating seriously because we don't change anything on the other machine, then let updates automatically, this is obviously some update that triggered connect to stop the local distribution of load and internet access now it shows only local access.

  Appreciate any help out there on root causes.
  So far not much dad worked. R/Paulcou

  Hello

  In your case, I would first check the settings of the router.
  I put t know what settings of your router is compatible, but you should go thought the simple options (such as when the first router configuration) and should check if everything is set correctly.

  In addition, you should check the settings of WLan connection. In the properties of WLan connection, you would find the TCP/IP protocol. Check the properties of the TCP/IP Protocol and set all parameters (IP address, getaway, etc.) to get automatically.

  If all of these settings are set correctly, then start the console (CMD) and use the command:
  ipconfig / renew

  This should refresh the IP address and in most cases, it helps.

  Last but not least, you should check if you can update the WLan driver!

• your ip address of the router and the printer's address must be the same, so it can print from the computer

  IM setting upward a new router and wants to find the printer but the printer and the router are different VPI address Will this work

  Are they similar addresses, for example 192.168.1.1 for the router and 192.168.1.37 for the printer, it should work file.  If they are more than just a bit different - say for example instead of 192.168.1.37 the printer address is 192.168.0.100 or 169.54.45.21 - then is not likely.  In most home networks, the first three bytes of the IP address must be the same with the fourth byte is different for each computer or device connected to the network.

• Will HELP WRT610N - Do not get the IP address of the router?

  I had trouble with my WRT610N...  It of sortof in brick after attempting to upgrade linksys firmware again.  Unable to access but to pings.  I've held reset and plug in the unit and access management screen and download the latest linksys firmware.  He waits and says will take in the results screen well after the time it is trying to load, but says cannot display... If I type 192.168.1.1 I can screen settings...  Apply all the settings and it seems to work, but if I unplug my router or do the 30/30/30 reset firmware and I'm back to the management screen...

  After coming back to the method of administration and the firmware installed again.  When I return to the settings of the router, it keeps all my settings, such as changing the password and settings wireless, but for some reason not the firmware?

  OK, so I have the router to hold the linksys firmware after a restart of 30/30/30... However the router will not get an ip address from the modem... Any ideas there?  Thank you!

  Well, seems to work for now... I unplugged the modem and the router... A modem plugged in when he was on the rise and I plugged the router running in and hooked up to computer and after a few it obtained IP and seems to work well.

• IP ADDRESS OF THE ROUTER WRT320N

  I recently bought the WRT320N router.  Set up was easy, I have 2
  computers (1 wired and 1 wireless). I have a wired
  printer. Recently, my son, home from College and he was able
  access my network of wirleess without any security problem.  The simple link
  Counsel has not indicated his computer while he was on the network (it
  lists the mentioned previously 2 computers and printers).  I tried
  to access the routers Set up basic web. I checked my computer and the
  The IP address is 192.168.1.1.  However, when I try to get on the web through the
  (http://192.168.1.1), I get "Internet Explorer can not display the.
  Web page.  Why is this happening? Why does my network seem to not course?

  Open a command window and type in ipconfig.  Verify that the default gateway to verify the IP address of your router is 192.168.1.1.  If this isn't the case connect you to this address and see if you can get to the admin pages.

  If it is still impossible to connect hard reset the router by pressing the reset for 30 seconds button and hold then release.  Wait 30 seconds and cycle power to the router.  Do not attempt to connect with the username password empty admin.  Reconfigure your router to your setting, then check your secruity.

• My IP security camera is different my network ip address, how to configure the camera to match the ip address with the router cable time Wörner

  Please someone help me configure my camera IPsecurity model m12 mobotix ag. It allows to work in the corporate network, but they close down and I didn't bring the camera House but there different IP address of my network and I don't know how to configure the camera to have the same IP address with my home router to TWC, thanks

  Router connections by opening network, in the Panel control, search for the router / properties, enter its configuration

  data in the boxes provided, you will get on the router, a sticker shows data. If lost or deleted, go to its Web

  for the data. Also, perhaps the home page of IP camera offers software/drivers.

• InDesign CS4 - change engl. The language of the INTERFACE in German

  Hello

  I use the ID CS4 and to change the menuelanguage (ui - UserInterface) of engl. in German,.

  How can I do?

  I use it on WIN 7 with systemLanguage is German.

  The CS4 Mastersuite is complete installed.

  Photoshop and Dreamweaver run in German.

  a big thank you

  T.Rosenthal

  Same I have answered in the InDesign forum: not possible with Creative Suite products. Easy if you get a creative cloud subscription.

• InDesign CS4 bookmarks can cause the same name?

  Hello

  I am a new user of Indesign CS4 and have recently created a 388 pages in PDF with bookmarks entered using the bookmarks of Indesign Panel.  However, in the PDF, I find that if a bookmark in a chapter has the same name as one bookmark in another chapter, then clicking on the first bookmark takes you to the page indicated the second - as if somehow to create the second bookmark has "substituted" the page of the first reference.

  I me assuming that bookmarks have their own unique ID and what to say, with a bookmark called "Economic factors" in Chapter 1, and a bookmark bearing the same name in Chapter 2, would agree.  However, in the PDF I created from Indesign, this isn't the case.

  Please can someone advise?  I'm doing something wrong?

  Best regards

  Sarah

  I played and I'm able to reproduce your results in certain circumstances. I think it is a bug, and it's there in CS5, too.

  I also found a workaround, but there will be a LOT of work in a doc where you already have created bookmarks. As I said, this happens in certain circumstances in my tests, especially when you highlight the text and create the new bookmark and accept the name of the bookmark in the highlighted text. Even change the name of the selected text does not appear to make a difference, at the time of creation or thereafter. On the other hand, so simply, you place the cursor to the location of the text and make a new bookmark, the default name will bookmark N (N is a sequence number) and you can change it to what you want.

  I made two sets of bookmarks nested covering different pages and names them ALL identically. They all work correctly, if my guess is that the bookmark resumes the name of highlighted text, but a number of generic sequence of a plain insertion point and everything is picked up sticks. If you take the same name you no longer have an identifier unique, and that leads to the same problem of destination, but I want to emphasize this is just a guess.

  So that this works, you must recreate the bookmark. You cannot rename.

  I filed a bug on this.

• 169.254.what? Xbox 360 can't get the ip address of the router or modem.

  OK first off I know that you have solved this problem in this forum before. I could not know how to solve based on available positions. In any case, I'll have the old 169.meta some problem. I feel like I need to change the IP to automatically configure for LAN but I don't know how. BTW, I have my laptop wireless connected to the router and the xbox 360 has an ethernet cable connected to the router. The router is a Linksys WRT54G2, the modem is a Motorola SB5101 surfboard and the laptop is a HP Pavilion dv6000 running Windows 7. I tried all troubleshooting and simple diagnostic tests as restarts and the default settings and cables control and router config etc. Please help me solve this problem. I am tech savvy but only up to a point it seems. Thanks in advance for your time and your response.

  Hello

  Follow the steps in http://support.xbox.com/support/en/us/nxe/kb.aspx?ID=978976&lcid=1033&category=xboxlive

  Diana

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.