Menu initialization problem

Similar Questions

• Codec initialization problem!

  Hello

  I'm trying to use Adobe Media Encoder CS6 to convert a mov file to size 3072 by 768 resolution f4v to the same attributes.

  However, I get the error Codec initialization problem!.

  I can convert f4v 1920 x 1080 or other lower resolutions.

  Help, please.
  Thank you

  I am able to export 3072 x 768 to F4V, if I set the profile: high and level: 5.1

• Firefox 38.0.1 window resized with menu bar problem

  After update to 38.0.1, I have the active menu bar, and I have a problem with the firefox window, changing size when displaying pages. The entire window jitters then I lose the bar menu at the top of the tab bar. at this point, I can't click or enter data into a web page. If I select the border of the window and resize or move the window back to its original with the menu bar size and displayed correctly tabs.

  I also developer of Firefox v 40.a02 it was OK last week I was last updated on 29/05 and now also has the same problem.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

  • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
  • Do NOT click on the reset button on the startup window Mode safe
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

  You can try to disable hardware acceleration in Firefox.

  • Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.

  You will need to close and restart Firefox after enabling/disabling this setting.

  • https://support.Mozilla.org/KB/upgrade-graphics-drivers-use-hardware-acceleration

• Toolbar Menu display problem

  Whenever I try to use any menu in Firefox, they sparkle inside and out. It is extremely difficult select Favorites or even Alt click on a link to "Open in New Tab" I have hover over menu items, they disappear and then come as soon as I move my mouse away.

  I've disabled all the Add-In, but the problem persists. The only way it goes is if I start Firefox in "safe" mode with all disabled while everything works correctly.

  Hello rob.seitzinger, try turning off hardware acceleration and check again, in safe mode, acceleration hardware is disable.

  Thank you

• HP50g - menu soft & problem of local procedures

  Pls help!

  Below is a simple program to illustrate the problem with a menu soft & updated local procedures

  (-> and <-stand for left and right arrows)

  Program works great under debugger! (displayed correctly SALDO and TRANS in response to press the soft keys)

  But started him only gives error messages: "undefined local name.

  According to the manual update of local variables (here < s and <-T) must be visible in the module of the whole program, or I don't unerstand not something?

  Of course program works very well when the overall procedures are used instead of the premises.

  Thanks in advance for your advice

  < <

  < < "SALDO" > >

  < < "TRANS" > >

  --> < s < t

  < <

  {

  {"SALDO" < < < if EVAL > >}

  {"TRANS" < < < t EVAL > >}

  } MENU

  > >

  > >

  Hello

  A local variable has 1 main feature: a scope.

  This range means that the variable only exists in this scope...

  A scope is a 'physical' and time stretch (note the quotes around physics, it's because he's not real physics, but virtual physics).

  Expand the 'physical' is the length/area of the program where there is the local variable. This extension from the definition of the local variable until the closure of the program block is more deep where the local variable is defined.

  The measurement of time is the duration of execution of the execution of this program block.

  There is a secondary feature: this is the name and it is the recognition by the system.

  RPL, as in most languages, the basic rules of the gramar program allows a local variable to have a name any. Therefore, at first inseparable from a global variable. The compiler then uses his knowledge of the field of knowledge, when you type a name, if it is to create a local or global variable.

  Until then, there is no problems in the definitions...

  Now, let's look at your program (in essence)

  < < 1 2 - > V1 V2

  < <

  {{V1 'V1'} {'V2' V2}} MENU

  > >

  > >

  When the program runs, it creates 2 MENU items, and then OUTPUTS!

  At the time where your more intimate program stops, local variables are destroyed (normal, follow the rules)...

  HOWEVER, you left a temporary structure that is available to the user (in the menu) which contains references to these variables (which no longer exists)... When you press one of these keys to menu... KaBoom...

  But what that <-syntax stuff?

  Don't forget the 'physical' extension of the scope... It's all good and all... BUT it has some issues.

  Namely, you cannot split your program into small chuncks, stored in various global variables to facilitate programming.

  In most languages, and according to the rules defined above, you may not create a subroutine, using local variables that you plan to have exist in a "time extend" which covers the delivery of the subprogramme. This is true of most programming languages. The reason why you could not create this subroutine is that the compiler would not know/believe these variables are 'in the scope' during the compilation of the program (* see tip below).

  The <-syntax allows this. It allows to force a variable to be compiled as local even outside the physical measure of the scope. But at the time of this call to the local variable, the variable MUST be defined, otherwise... KaBoom!

  This is the heart of your misunderstanding...

  To do what you want, you have 2 possibilities:

  -Use global variables

  -Put a STOP after the MENU statement (you must use TMENU BTW) and a SUITE at the end of execution of each of the menu items.

  I hope this helps!

  Cyrille

  * trick below *.

  The 50 HP has an environment / planning of circuits integrated very neat that lets you do the following to avoid having to type those pesky arrows back.

  Create your top program with your local variable definitions (not necessary of arrows). Just after the definition of the local variable, place a STOP instruction. Run the program.

  Now you can create your SUP program! When you press ENTER and the system compiles your program, these variable EXIST local (you are in their scope of TIME!) and your program will contain local variable rather than global calls!

  However, this will not solve your problem.

• Testo 176 - Serial initialization problem

  I'm trying to get the 176P 1 talk with labview Testo 2011.

  I downloaded the TestoToolbox and also got an update for German help with an installer of Toolbox2.exe.

  In any case I can't pass the initialization process with the tcddka.dll of the Testo (V1.2).

  I have a simple question: this device name feed to the Init procedure?

  (1) the name, you can see in devicemanager?  in my case "testo 175-176-2010"--> Exception occurred in tcddka: invalid DeviceName in testo init.vi series

  (2) give but: 'testo175-176-2010'--> me ' Exception occurred in tcddka: the device does not respond in the series init.vi testo ".

  (3) or the general "testo175-177" translates by "Exception occurred in tcddka: the device does not respond in the series init.vi testo".

  Seems that I put the COM port correctly!

  + testo software is able to connect with the device without problem.

  earliers messages on a Testo gas detector, I have seen characters added and changes made to the comsoft.cat file...?

  All suggestions are welcome!

  I managed to get this 'base software comfort' currently running on a computer at home and changed the mode of operation of 'Connect' to the "extent", see below the image

  

  This cannot be given with the Lee Version 5 software, you have V4 that I found on the Web site, but has received assistance in Germany.

  This solves the problem and now I can acquire the data of the device with the highest vi attached!

• Initialization problem

  Hello

  This is my code:

  int main (int argc, char * argv [])
  {
  error int = 0;

  / * initialize and load resources * /.
  nullChk (InitCVIRTE (0, argv, 0));
  errChk (panelHandle = LoadPanel (0, "CVI GUI.uir", Panel));

  / * display of the control panel and run the user interface * /.
  errChk (DisplayPanel (panelHandle));
  errChk (RunUserInterface ());

  initialize everything
  if(cycle == 0) initialize (Panel);
  else ResetTextBox (Panel, tabPanel1_tbxSystemMessage_A, "not initialized");

  Error:
  / * Cleanup * /.
  If (panelHandle > 0)
  DiscardPanel (panelHandle);
  return 0;
  }

  Sub Initialize (int Panel)
  {

  srand (time (NULL));

  now activate timer
  SetCtrlAttribute (Panel, tabPanel1_tmrTIMER, ATTR_ENABLED, TRUE);

  } //END Initialize()

  I met 2 problems that I can't fix right now.  I use global variable 'cycle' as my number of cycles, with the initial value of 0.  'cycle' is incremented by 1 each time that ticks of the timer.  In the Main() code, when it is zero, I call my function Initialize().  However:

  1. the Inifitialize() function is never called.  The timer is never activated.

  2. the object referencing a problem.  This line:

  ResetTextBox (Panel, tabPanel1_tbxSystemMessage_A, "not initialized");

  has a problem with 'Panel' (a global object).  I try again with 'panelHandle', and always he fouls out.  Same thing with this line:

  SetCtrlAttribute (Panel, tabPanel1_tmrTIMER, ATTR_ENABLED, TRUE);

  The "jury" passed is incorrect if the timer is never activated, but I don't know what is right for him.  Anyone has an idea on how to fix it?

  I think I found the root of the problem.  These two lines:

  errChk (DisplayPanel (panelHandle));
  errChk (RunUserInterface ());

  bring up the user interface and the thread goes in.  Anything done on the user interface written after these two lines are not executed until the thread leaves the user interface.  The Timer object exists only in the UI thread.  Thus, anything done to the "jury" and the timer object must be within the UI thread.  I changed my code to get concrete results.  in any case, thank you so much Wolfgang.

• initialization problem multiple serial

  Hello all

  I have attached a vi that gives me a problem I cannot solve and would appreciate any help.

  The vi is supposed to intialise up to 7 ports series (only using 5 at the moment), and I guess that's a plausible way to do initialization (maybe wrong). The serial ports are connected to a pc via a usb hub. The windows XP operating system recognizes the Device Manager ports.

  The problem is that when the vi is executed, the following error is reported as shown in the word document attached.

  I compared the port settings in the properties in Device Manager for each port to the vi settings, and they match. What can we do?

  If anyone has a configuration with several serial ports could try the vi and see if it works for them?

  Thank you and best regards

  Ray

  It has nothing to do with several serial ports.  This has to do with an invalid parameter, you are trying to use it to configure one of the serial ports.

  Look at the information in the error message.  Point 4 of the property node to configure Serial Port VI is the setting of Stop Bits.  I see a point of stress goes in this VI, then that tells me the type of data in performing connections does not quite.

  You have an array of values of I32 and your values are made up of 1.  Disconnect this table and right-click on the terminal to configure Serial Port VI and choose Create Constant.  You'll see you get a data type of ring.  It's a U16.  But if you look at the items in there, you will see that the stop bits 1.0 has a value of 10.  1.5 has a value of 15, 2.0 has a value of 20.  If the value of 1 has no meaning to this property node and you get an error.  You should be wiring in a value of 10.

  Delete this table.  Create a table of constants in the ring.  Turn it into a control, and then choose the value of the correct ring for each item in your table.

  You have several other points of constraint.  They may not cause problems, but I consider disconnect them, create a constant of the correct data type and that using the table that you wire to configure Subvi.

  I have modified your VI and attached to it.  See if it works for you.

• Menu toolbar problem and start for windows vista Home premium 64-bit

  I've recently been tweaking and accidentally got rid of my explorer.exe file, (I think that I sent to my trash and maybe deleted it?). Once I realized that I just typed as a new task and it reappeared.  The problem I have is that since then I had no toolbar or start menu.  I tried to access it through the control panel that does not work; I tried Ctrl Esc, which does not work, I tried everything I can think of? What's weird, that's all my desktop icons are great, and for some reason if I have Ghost click my mouse in the lower right of the screen I open random programs usually on my toolbar, I can even drag on my desk.  I tried to find common ground, if my toolbar is there somewhere?, do to slide it back on my screen, but it was done without success.  Another thing is when I start my computer in safe mode, my toolbar appears with my Start menu icon?  Anyone know what may be the problem?  I am running windows vista family premium. operating system: 64-bit

  Hello

  Method 1:

  As you are able to see the toolbar in safemode, I suggest that you perform the clean boot to limit the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

  Method 2:

  I suggest check the link and try to perform the checking and scan SFC (System File Checker) if it helps.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Let us know if it helps.

• Strange Desktop / Start Menu redirection problem

  Hi all I have a very strange problem on a field of 2012 server using Windows 7 desktop computers.

  When a user connects for the first time the office menu and start to not redirected and I have the following error

  You cannot apply policy and redirect the "Desktop" folder to "\\SVR\Desktops$".
  Options of redirection = 0x1000.
  The following error occurred: "unable to generate a list of known subfolders.
  Details of the error: "the system cannot find the specified file.
  ".

  However on 2nd session opening the desktop and start menu are redirected properly.

  Description:
  Applied with political success and redirected folder "Desktop" to "\\SVR\Desktops$".
  Options of redirection = 0x1000.

  This seems also only affect the recent HP Prodesk computers, we started to use.

  Desktop and startmenu redirects are configured for a group of users and permissions are the following

  Share permissions - full control everyone

  Folder permissions - UserGRP Read and Execute only

  Any help would be appreciated

  Hello

  Thanks for posting your query in Microsoft Community.

  Your question is beyond the scope of what is generally answered in this forum of consumer and would be better suited for the IT Pro TechNet public.

  Please post your question in the TechNet Forums.

• Menu scrolling problem

  Hello

  I PIN to the adobe menu bar muse at the top of the master page. But when I saw a page and scroll down the content come top of the menu. I solve similar problem by rearranging the layers. The problem is that the content of the page and the menu bar are placed on different pages, one on the master page, and the other, say home page. This means it no menu layer that combine them. then I could not reorder the layers of different pages.

  Could all help to solve the problem.

  Best regards

  Sheikh Maawiya

  Select the page where the Menu is inserted, where materials are flowing on the menu. Go to layer and create a new layer, move to the top of the page, and then drag the Menu to this layer.

  If menu is on different master, then the master page made even with diapers.

  Thank you

  Sanjit

• Hyperlink for the Menu composition problem

  Hello.

  I have a Web site that is used in mode offline, saved on a disk shared in my workplace network.

  On this site, I have a menu created using the widget of composition.

  Clicking the trigger must show a target rectangle that displays links to pages in the category.

  However...

  Displaying in Internet Explorer the hyperlinks work, but are all crushed together upwards and do not appear as I designed / formatted their (image below).

  

  Display of hyperlinks in Firefox when the display as designed / formatting, but the links are not clickable (image below).

  

  In addition, I don't know if this is related, but in Firefox, when loading first site it seems to try to connect to the so-called Business Catalyst (as evidenced by the link is visible in the lower left corner of the screen) and crashes while he does.

  I first thought is maybe a matter of layer but have you checked, and the text box is configured to be up front with the rectangle target to be back.

  Any help would be greatly appreciated as this is driving me crazy!

  Thanks - Glen

  I am not sure, but it might be a police problem. Try to set it to a web-friendly - if that doesn't work, delete the text box and recreate it from scratch and see if it works

• EJB initialization problem

  Hi all
  
  I've migrated EJB 2.1, EJB 3 in my JSF project and facing a few problems during initialization by annotations.
  
  
  My JSF Managed Bean 1
  

  @ManagedBean(name = "mybean1")
  @RequestScoped
  public class MyBean1 { 
       public MyBean1 () { 
            super(); 
       }
  
       private String defaultTab = "";
       
          @EJB(name = "MyEJB") 
          private MyEJB myEJB;
  
       @javax.annotation.PostConstruct 
       public void init() {
            defaultTab = myEJB.retrieveDefaultOption(); 
       }
       
       public String loadDetail() {
            System.out.println("defaultTab::"+defaultTab);
            return "detail";
       }
  }

  My JSF Managed Bean 2
  

  @ManagedBean(name = "mybean2")
  @SessionScoped
  public class MyBean2 { 
       public MyBean2 () { 
            super(); 
       }
  
       public String showDetailForTracking() {
            MyBean1 myBean1 = new MyBean1();
            myBean1.loadDetail(); // Always prints defaultTab::     
            return null;
       }
  }

  When the loadDetail at 1 bean method is called bean 2 as shown in the snippet above, the default tab value is always "' as the EJB is not being built.
  
  Is there a way to solve this problem. Any suspicion on this would be much appreciated.
  
  Thank you.

  Think about it: you build MyBean instance yourself. Why do you want that the container to inject magically reference EJB in it then?

  Good mechanics JSF allows to inject the instance MyBean1 MyBean2! JSF 2 any book or article would have told you how. You can use the ManagedProperty JSF annotation:

    @ManagedProperty(value="#{mybean1}")
    private MyBean1 myBean1;
  

  or if you're on a JEE 6 container you can invest time in research on how to use the Commission for not only one model standardized injection.

  And a final tip: you make your life unnecessarily difficult by substituting the names of the default bean.

• Menu widget problem, after obtaining the last menutab you cannot back

  Hello.

  I had a problem with my menu.
  This site http://phinofilm.com/

  When you click on the menubuttons everthing is fine until you click on "Kontakt" (last) then you are stuck on this page and can't get anywhere.

  What should I do?
  
  

  Hi Martin

  It seems that you have removed the Menu style that now if I check the site, Menu is not boxed more.

  I was talking to the form that is inserted into the contact page, the framework of the contact form was going on the menu items which was idle.

  Go back the changes, and then check the setting of the contact form, try to balance that, down.

  Thank you

  Sanjit

• Spry menu bar problem

  Hi all, new here and also a new Adobe product user. I'm learning Dreamweaver at the present time and it is excellent if a little discouraging sometimes.

  I need some help with a problem of Spry. When I insert a new Spry menu on my page in Dreamweaver, the submenus don't drop-down for me. For example - if there are 3 elements of submenu 1.1, 1.2 and 1.3, when I click on the arrow, I don't see the point 1.3... 1.1 and 1.2 seem to be obscured view?

  I have attached a small image to show you what it looks like. Any help would be greatly appreciated as it continues my little project something terrible

  Thank you guys

  Pol

  

  If you customize, make sure not to remove anything vital or you will break it.

  READ THIS FIRST:

  Menus Spry 10 commandments

  http://www.dwcourse.com/Dreamweaver/ten-commandments-Spry-menubars.php

  Nancy O.