Migrating from a Pix 525 ASA 5540

Similar Questions

• Migrate from tunnel vpn again ASA

  Hello

  Is it possible to migrate an existing sites (vpn) to a new ASA.

  We have more than 50 offices connected to our main office, we have installed a new Firewall ASA with a bigger pipe.

  I need a way to migrate the offices which saves time (go through each office) and silver (buying a new router and send it with the new configuration).

  I thought to add a new address of peers and kill the pre-shared on the old VPN.

  can someone help me please.

  Yes.

  I would like to do the following if I was responsible for this project.

  1. Configure the new ASA with all groups of tunnel for remote counterparts and the rest of the VPN configuration (cards crypto, ACLs, NAT, etc..)
  2. Connect on the ASAs remote through the external interface.  Most organizations allow SSH/https to their specific management firewall IPs to the main site.
     1. Create a tunnel-group for the period of INVESTIGATION by the ASA peers again.
     2. Change the existing crypto map peer IP to point to the new IP address.
  3. On your core network on the main site routing, change/add an IP route to local subnets pointing inside the site remote interface of the new ASA for your local network to reach remote sites correctly.

  This should be it.  Thank you.

• Convert the VPN Site-to-Site of PIX to ASA 8.2

  I worked on the conversion of a config above a PIX an ASA 8.2 but I am running into trouble with the site to site vpn. The PIX has a VPN client and site to site. Given that some of the configs for the cross from site to site on the VPN client I'm confuse. Any help would be apperciated.

  Below are excerpts from just the PIX VPN related orders.

  permit access ip 192.168.0.0 list Remote_splitTunnelAcl 255.255.0.0 any

  inside_outbound_nat0_acl ip access list allow any 192.168.0.160 255.255.255.240

  inside_outbound_nat0_acl Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl SilverBack NOC 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl allowed host NOC 255.255.255.0 enoss_Hardware ip access-list

  outside_cryptomap_dyn_20 ip access list allow any 192.168.0.160 255.255.255.240

  outside_cryptomap_20 Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 SilverBack NOC 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 Zenoss_Hardware CNP 255.255.255.0 ip host allowed access list

  IP pool local DHCP_Pool 192.168.0.161 - 192.168.0.174

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  Sysopt connection permit VPN

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set 205.x.29.41

  outside_map crypto 20 card value transform-set ESP-DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  client authentication card crypto outside_map LOCAL

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key address 205.x.29.41 netmask 255.255.255.255 No.-xauth-config-mode no.

  ISAKMP nat-traversal 180

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  part of pre authentication ISAKMP policy 40

  encryption of ISAKMP policy 40

  ISAKMP policy 40 sha hash

  40 2 ISAKMP policy group

  ISAKMP duration strategy of life 40 86400

  vpngroup address pool DHCP_Pool GHA_Remote

  vpngroup dns 192.168.0.11 server GHA_Remote

  vpngroup wins 192.168.0.11 GHA_Remote-Server

  vpngroup GHA_Remote by default-field x.org

  vpngroup split tunnel Remote_splitTunnelAcl GHA_Remote

  vpngroup idle 1800 GHA_Remote-time

  vpngroup password KEY GHA_Remote

  I guess what I really wonder is if someone can convert the version of site to site of this VPN ASA 8.2 config so I can compare it to what I have. I need to have this, so I can just fall into place and work.

  Also, it does appear that political isakmp 40 are used, correct?

  On your ASA in Setup mode, simply type vpnsetup steps for remote access ipsec or vpnsetup site - not and it lists what it takes or you can download the PIX of the ASA migration tool.

• Allowing ICMP and Telnet via a PIX 525

  We are trying to build a new block of distribution to our backbone WAN. We are experiencing a problem when establishing ICMP and Telnet via the PIX. The following is known:

  1 Ping and telnet to the 6509 and internal network works very well for the PIX.

  2 Ping the 7206 for the PIX works just fine.

  3 debug normal to see activity track ICMP for connections ICMP for the PIX of the network 6509 and internal; However, the debug shows nothing - no activity - during attempts to ping at a.b.5.18. (see below).

  In short, all connections seem to be fine between the three devices, however, we can get ICMP and Telnet work correctly through the PIX.

  The layout is:

  6509 (MSFC) - PIX 525-7206

  IP:a.b.5.1 - a.b.5.2 a.b.5.17 - a.b.5.18

  255.255.255.0 255.255.255.240 255.255.255.240

  (both)

  networks: a.b.5.0 a.b.5.16

  255.255.255.240 255.255.255.240

  6509:

  interface VlanX

  Description newwan-bb

  IP address a.b.5.1 255.255.255.0

  no ip redirection

  router ospf

  Log-adjacency-changes

  redistribute static subnets metric 50 metric-type 1

  passive-interface default

  no passive-interface Vlan9

  ((other networks omitted))

  network a.b.5.0 0.0.0.255 area 0

  default information are created

  PIX 525:

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  nameif ethernet2 security10 failover

  hostname XXXXXX

  domain XXX.com

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 1720

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  names of

  access ip-list 102 permit a whole

  access-list 102 permit icmp any one

  access-list 102 permit icmp any any echo

  access-list 102 permit icmp any any echo response

  access-list 102 permit icmp any any source-quench

  access-list 102 permit everything all unreachable icmp

  access-list 102 permit icmp any one time exceed

  103 ip access list allow a whole

  access-list 103 allow icmp a whole

  access-list 103 permit icmp any any echo

  access-list 103 permit icmp any any echo response

  access-list 103 permit icmp any any source-quench

  access-list 103 allow all unreachable icmp

  access-list 103 allow icmp all once exceed

  pager lines 24

  opening of session

  timestamp of the record

  logging buffered stored notifications

  interface ethernet0 100full

  interface ethernet1 100full

  interface ethernet2 100full

  Outside 1500 MTU

  Within 1500 MTU

  failover of MTU 1500

  IP address outside a.b.5.17 255.255.255.240

  IP address inside a.b.5.2 255.255.255.240

  failover from IP 192.168.230.1 255.255.255.252

  alarm action IP verification of information

  alarm action attack IP audit

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Access-group 103 in external interface

  Route outside 0.0.0.0 0.0.0.0 a.b.5.18 1

  Route inside a.0.0.0 255.0.0.0 a.b.5.1 1

  Inside a.b.0.0 255.240.0.0 route a.b.5.1 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  No sysopt route dnat

  Telnet a.0.0.0 255.0.0.0 outdoors

  Telnet a.0.0.0 255.0.0.0 inside

  Telnet a.b.0.0 255.240.0.0 inside

  Telnet a.b.5.18 255.255.255.255 inside

  Telnet timeout 5

  SSH timeout 5

  Terminal width 80

  Recognizing any help on proper routing through a PIX 525, given that all this is for a network internal.

  on the 6509, why the int has a 24 subnet mask, when everything has a 28? If you try the 6500 ping.18, he thinks that it is on a local network, and there no need to route through the pix

  Your access lists are confusing.

  access-list # ip allowed any one should let through, and so everything that follows are redundant statements.

  for the test,.

  alloweverything ip access list allow a whole

  Access-group alloweverything in interface outside

  should the pix act as a router - you are effectively disabling all firewall features.

• Balancing on two PIX 525

  I'm creating network solution that will have two firewalls Pix 525 related to two different suppliers. For performance reasons, I'd like my clients to connect to Internet via two firewalls in "round robin" mode. What are my options?

  I want to create something like bridge load Protocol (GLBP) Balancing on the router 2800 series. I do not know and cannot know if Pix supports GLBP. Otherwise, are supported by any similar solution?

  Thanks for any response.

  Hello Milos,

  I have another solution for you for 2 ISP requirement of OER (optimized for Edge sending). Here is the link that will show the multiple scenarios and functionality.

  http://www.Cisco.com/en/us/products/ps6599/products_data_sheet0900aecd801dfcec.html

  If you find good, then you can run your firewall in failover mode, behind the router master REL for reasons of security, but not for purposes of routing.

  2nd solution could be to ACB with multiple tracking Options:

  http://www.Cisco.com/en/us/Tech/tk364/technologies_configuration_example09186a0080211f5c.shtml

  In the 2nd solution also, you can use PIX behind the router in for regular security to security policies.

  3rd solution: you can use 2 2800 routers and terminate ISP links on both of them and run GLBP between them.

  Here are the PIX balancing g. load balancing is supported in PIX 7.0 from only:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_guide_chapter09186a008054c4b7.html#wp1102712

  concerning

  Michael C

• Version 7.0 of the PIX and ASA 5500

  Hi all

  Is ASA 5500 series identical a PIX 515 or 525 or 535 with version 7.0... I still see some areas where it confused between version 7.0 of the PIX and ASA 5500 series... If not, what are the benefits of ASA 5500 on the PIX 7.0?

  ASA is not the same as PIX, ASA is different hardware architecture. Although both can run the same code. One of the benefits of the SAA is that you can have an IPS module in it to make the prevention of intrusions.

  Search for comprarison on CCO.

• PIX and ASA Site to Site (ACL)

  I am trying to configure a VPN tunnel from site to site between my PIX515 (6.3) to a seller ASA 5510. We can get the tunnel when the ACL match is all of this period, but when we try to use TCP and a specific port, nothing comes through. Any thoughts? I would be able to limit the interesting traffic to what is not necessary? I'm only looking on the side of the ASA to access a resource on the side of PIX on 1521 TCP. The side PIX didn't need to access anything whatsoever on the side of the ASA.

  PIX side ASA x.x.x.x y.y.y.y side

  This ACL works...

  PIX

  ip host x.x.x.x y.y.y.y host access list vendor permit

  ASA

  host host x.x.x.x y.y.y.y ip access list vendor permit

  This ACL is not...

  PIX

  access list provider permit TCP host x.x.x.x eq 1521 host y.y.y.y

  ASA

  access list provider permit TCP host x.x.x.x eq 1521 host y.y.y.y

  Phase 1 Isakmp appears fine, fails just on the Ipsec data transfer.

  No, only versions 7.X code support the use of the tunnel-groups and group policies that are needed to implement filtering of VPN.

  I would suggest filtering traffic at the becauase of the SAA on the PIX, you will need to remove the 'permit sysopt-connection ipsec' command (if it is not already deleted) to start filtering on the external interface.

• PIX 525 config and VPN configuration

  Hello

  I was asked to work on a customer request to replave sound no cisco FW with a pix 525 and also lead to a VPN solution using this PIX 525.

  I'm not a FW as my main experience is with Routing/Switching, but I have read some documentation and had some hands on a client of vpn300 501 PIX and cisco.  I managed to make it appear the vpn connection, even if all tests have failed (you need to solve any further).

  Customer has its main site with an application that runs on a Web server that must be accessed only through the vpn to: 3rd party + a few remote users.

  The solution, I want to propose to the client is:

  option 1:

  PIX 525 as a vpn server + Cisco vpn 3000 client on all PCs of remote users.

  option 2:

  PIX 525 as a vpn server + vpn client windows on all PCs of remote users

  option 3:

  PIX 525 as vpn + PIX 501 to 3 rd party server + vpn client windows on all PCs of remote users

  First I want to confirm that these motions are feasible.  So which option should I go for knowing that the remote users are only about 10.

  Client doesn't no Ganymede or RADIUS should go for statis userid/pass set up on PIX525?

  Any idea, advice, suggestion is welcome.  Thanks in advance

  Kind regards

  ngtelecom

  Hello

  Option 1

  In my opinion, is the best solution because the PIX 525 will act as a firewall and the VPN server.

  Then, all the clients connect via VPN using Cisco's VPN IPsec client software.

  Option 2

  The advantage of this option is that you do not need to install VPN software on clients (not a problem, only 10 clients)

  The problem is that it does not come with split tunneling and don't provide as good protection as Cisco software.

  Option 3

  This is also valid, and you can do an EasyVPN connection where the 525 is the server and the 501 to the customer.

  Local authentication on the PIX 525 sounds great.

  As a recommendation, the PIX are EoS and the replacement are the ASAs.

  It will be useful.

  Federico.

• Thunderbird. Migration from Windows Mail (Win7) and Firefox 35.0.1 is not compatible with ImportExportTools of Mozilla Support

  Try to migrate from Windows Mail, NOT Windows Live Mail in Windows 7 Home Premium.
  When I try and import the messages I get the message ' ImportExportTools is not compatible with FireFox 35.0.1.
  I'm following the instructions at https://support.mozilla.org/en-US/kb/switching-thunderbird.

  Y at - it a compatible version?

  Concerning

  Chris Parker

  You can download the extension using Firefox.
  But you will need to install it in Thunderbird.
  http://chrisramsden.vfast.co.UK/3_How_to_install_Add-ons_in_Thunderbird.html

• migration from Outlook Express loses everything after 'group '.

  Hello
  I migrated from Outlook Express to Thunderbird on XP, then moved the files to Windows 8.
  I had a 'group' in my OE address book. Nothing after that that group name (which began with an H) has been migrated to the new address book. In other words, I lost everything after H.

  I also have these contacts on Gmail. Y at - it an easy way recover of EO (I guess I could remove the Group and start over, but it's a long process and I'm afraid to lose the mail I already sent on tuberculosis), or y at - it an easy way to get from gmail?

  Thank you.

  S

  There are several solutions to your problem, which is the best for you which I do not pretend to know.

  There is the possibility of simply to copy the WAB to outlook express for Windows 7 and double click it to him bringing in the windows contacts folder. I have instructions here http://thunderbirdtweaks.blogspot.com.au/2013/12/windows-contacts.html that include the Windows Contacts folder in Thunderbird.

  Alternatively, you can install one of the Add-ons to gmail contact sync. I use https://addons.mozilla.org/en-US/thunderbird/addon/google-contacts

• Are there plans to add "XMARKS" for mobile Firefox? I want to migrate from Dolphin. I have the premium version of the "LASTPAST / XMARKS ' installed on

  Are there plans to add "XMARKS" for mobile Firefox?
  I want to migrate from Dolphin.
  I have the premium version of the "LASTPAST / XMARKS ' installed on 4 platforms.

  I noticed that a user has requested to have problems to install XMARKS. I couldn't find this add on. I have it on my computers Windows Firefox. I also have it on my mobile devices.
  Thank you.
  Dick Proulx

  Hello luckyduck, as is the case with xmarks too, the overwhelming majority of the addons is not created by mozilla, but by independent third-party developers. so if you want to know if it is planned an extension for firefox on android porting or have other requests for features, please communicate with the developers involved directly in order to get a better answer. Thank you for your understanding!

• HP Pavilion dv6-6c45se: migration from hard drive to ssd

  Dear Sir / Madam
  I'm about to migration from HDD to ssd on my laptop.
  Now the question is: is my motherboard support sata 3?
  My laptop computer product name: HP Pavilion dv6-6c45se Entertainment Notebook PC

  My product number phone: A7P17EA #ABV
  I'll be glad if you help me
  Thank you

  Probably not with a 2d gen i5 processor, but it does not matter. It will support an SSD SATA-III, even if the SSD transfer is limited to SATA-II. It will always be very, very fast and you will never see no practical difference. Download the SSD, you will not be sorry. Let us know if you need help most.

• Migrate from Time Machine retains former name

  I bought a new iMac and migrated from Time Machine. He kept the name of my old computer. How can I change the name? Rename the hard drive does not help.

  Go to sharing in the preferences and change the name of the computer.

• Move photos on external hard drive after migrating from iPhoto to Photos

  I have a lot of photos and have you run out of space on my MacBook.  After doing some reading, I discovered that I should be bale to move my library to an external hard drive, then the point of Photos to run from the external hard drive.

  I have recently updated to El Capitan, and as part of this upgrade that my photos have been migrated from iPhoto to the Photos.  I just checked the current location of my library and I found two.  One is named Photo library and which resembles the pictures one use which makes sense.  However, I also have a file called iPhoto library and it is listed as a library migrated under file type.

  My question is, when I copy my pictures on the external hard drive also I copy the migrated thus iPhoto library?

  My question is, when I copy my pictures on the external hard drive also I copy the migrated thus iPhoto library?

  Yes, if you want to free up your internal disk storage moving two libraries of the iPhoto library you have migrated your external drive and the new library of Photos.

  The two libraries share the storage for the original images and previews.  As long as one of the libraries is always on the internal disk and using storage, storage is not released: see: Photos saves disk space to share images with your iPhoto or Aperture - Apple Support libraries

  Drag the two libraries to your external drive, then double click the pictures library to open it in photos and test it. Once you are convinced that the copied library works well, you can delete the original in the internal drive.  Do the same for the copied iPhoto Library if you have installed iPhoto.

• Migrated from DPM2010 to DPM2012 and reporting does not work

  Original title: due tapes dpm powershell online

  Hello

  Can someone please? I migrated from DPM2010 to DPM2012 and reporting does not work. The mmc console crashes.

  I intend to remove DPM and re - install, but in the meantime, I was wondering if anyone knows how to use Powershell to know which bands are due online and also the most Due strips to go?

  I searched through Google on all day, but found nothing so thought I would ask here.

  Thank you very much

  Willie

  Hello

  It would be better if you reposted the question to the Forum 2012 DPM.  Professionals will help you resolve the problem you are experiencing.

  DPM TechNet