PIX and ASA Site to Site (ACL)

Similar Questions

• Installation of site to site VPN IPSec using PIX and ASA

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  I am a site configuration to site IPSec VPN using a PIX515E to site A and ASA5520 to Site B.

  I have attached the lab diagram. Consider PIX and ASA are in default configuration, which means that nothing is configured on both devices.

  According to the scheme

  ASA5520

  External interface is the level of security 11.11.10.1/248 0

  The inside interface is 172.16.9.2/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 11.11.10.2 1

  PIX515E

  External interface is the level of security 123.123.10.2/248 0

  The inside interface is 172.16.10.1/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 123.123.10.1 1

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Could someone tell me how to set up this configuration? I tried but didn't workout. Here is the IKE protocol I have used.

  IKE information:

  IKE Encrytion OF

  MD5 authentication method

  Diffie Helman Group 2

  Failure to life

  IPSEC information:

  IPsec encryption OF

  MD5 authentication method

  Failure to life

  Please enter the following command

  on asa

  Sysopt connection permit VPN

  on pix not sure of the syntax, I think it is

  Permitted connection ipsec sysopt

  What we are trying to do here is basically allowing vpn opening ports

  Alternatively you can open udp 500 and esp (or port ip 50) out to in on the two firewalls

• PIX and ASA static, dynamic and RA VPN does not

  Hello

  I am facing a very interesting problem between a PIX 515 and an ASA 5510.

  The PIX is in HQ and has several dynamic VPN connections (around 130) and IPsec vpn remote works very well. I had to add a PIX to ASA L2L VPN static and it does not work as it is supposed to be. The ASA 5510, at the remote end, connects and rest for a small period of time, however, all other VPN connections stop working.

  The most interesting thing is that ASA is associated with the dynamic map and not the static map that I created (check by sh crypto ipsec his counterpart x.x.x.x). However, if I make any changes in the ACL 'ACL-Remote' it affects the tunnel between the PIX and ASA.

  Someone saw something like that?

  Here is more detailed information:

  HQ - IOS 8.0 (3) - PIX 515

  ASA 5510 - IOS 7.2 (3) - remote provider

  Several Huawei and Cisco routers dynamically connected via ADSL

  Several users remote access IPsec

  A VPN site-to site static between PIX and ASA - does not.

  Here is the config on the PIX:

  Crypto ipsec transform-set ESP-3DES-ESP-SHA-HMAC-IPSec esp-3des esp-sha-hmac

  Dyn - VPN game 100 Dynamics-card crypto transform-set ESP-3DES-ESP-SHA-HMAC-IPSec

  Crypto dynamic-map Dyn - VPN 100 the value reverse-road

  VPN - card 30 crypto card matches the ACL address / remote

  card crypto VPN-card 30 peers set 20 x. XX. XX. XX

  card crypto VPN-card 30 the transform-set ESP-3DES-ESP-SHA-HMAC-IPSec value

  VPN crypto card - 100 - isakmp dynamic Dyn - VPN ipsec

  interface card crypto VPN-card outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  access list ACL-remote ext ip 10.0.0.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  Thank you.

  Marcelo Pinheiro

  The problem is that the ASA has a crypto acl defined between host and network, while the remote end has to the network.

  Make sure that the acl is reversed.

• Version 7.0 of the PIX and ASA 5500

  Hi all

  Is ASA 5500 series identical a PIX 515 or 525 or 535 with version 7.0... I still see some areas where it confused between version 7.0 of the PIX and ASA 5500 series... If not, what are the benefits of ASA 5500 on the PIX 7.0?

  ASA is not the same as PIX, ASA is different hardware architecture. Although both can run the same code. One of the benefits of the SAA is that you can have an IPS module in it to make the prevention of intrusions.

  Search for comprarison on CCO.

• VPN between PIX and ASA

  I have a vpn beteen two sites, which works very well. traffic is launched from site A and can connect to the site B ok.

  I just tried to set up traffic from site B to site A, but its failure the vpn encrypt point. I checked the acl and they match:

  site A (PIX)

  Crypto acl

  access-list site_a permit tcp host 10.51.3.32 10.0.0.0 255.0.0.0 eq 3389

  no nat

  no_nat list of allowed access host ip 10.51.3.32 10.0.0.0 255.0.0.0

  site B (ASA)

  Crypto acl

  Site_B list extended access permitted tcp 10.0.0.0 255.0.0.0 host 10.51.3.32 eq 3389

  no nat

  access-list extended sheep allowed ip 10.0.0.0 255.0.0.0 10.51.3.32 host

  the only difference I see is the extended acl, but it works well in one direction?

  Thank you

  Hello

  Using port-based ACLs for crypto card is not recommended, use IP access lists and configure VPN filters to implement port restrictions.

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Kind regards

  Averroès

• How to monitor connections dropped and rejected on the PIX Firewall / ASA?

  I need to monitor the SNMP OID of the connections dropped and rejected on the PIX and ASA firewalls. Is this possible?

  If this is the case, what SNMP OID should I monitor?

  Syslogs and Netflow (introduced in version 8.2) are your options.

  No MIB can give you the numbers of conn.

  PK

• Convert the VPN Site-to-Site of PIX to ASA 8.2

  I worked on the conversion of a config above a PIX an ASA 8.2 but I am running into trouble with the site to site vpn. The PIX has a VPN client and site to site. Given that some of the configs for the cross from site to site on the VPN client I'm confuse. Any help would be apperciated.

  Below are excerpts from just the PIX VPN related orders.

  permit access ip 192.168.0.0 list Remote_splitTunnelAcl 255.255.0.0 any

  inside_outbound_nat0_acl ip access list allow any 192.168.0.160 255.255.255.240

  inside_outbound_nat0_acl Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl SilverBack NOC 255.255.255.0 ip host allowed access list

  inside_outbound_nat0_acl allowed host NOC 255.255.255.0 enoss_Hardware ip access-list

  outside_cryptomap_dyn_20 ip access list allow any 192.168.0.160 255.255.255.240

  outside_cryptomap_20 Zenoss_OS CNP 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 SilverBack NOC 255.255.255.0 ip host allowed access list

  outside_cryptomap_20 Zenoss_Hardware CNP 255.255.255.0 ip host allowed access list

  IP pool local DHCP_Pool 192.168.0.161 - 192.168.0.174

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  Sysopt connection permit VPN

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  card crypto outside_map 20 peers set 205.x.29.41

  outside_map crypto 20 card value transform-set ESP-DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  client authentication card crypto outside_map LOCAL

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key address 205.x.29.41 netmask 255.255.255.255 No.-xauth-config-mode no.

  ISAKMP nat-traversal 180

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  part of pre authentication ISAKMP policy 40

  encryption of ISAKMP policy 40

  ISAKMP policy 40 sha hash

  40 2 ISAKMP policy group

  ISAKMP duration strategy of life 40 86400

  vpngroup address pool DHCP_Pool GHA_Remote

  vpngroup dns 192.168.0.11 server GHA_Remote

  vpngroup wins 192.168.0.11 GHA_Remote-Server

  vpngroup GHA_Remote by default-field x.org

  vpngroup split tunnel Remote_splitTunnelAcl GHA_Remote

  vpngroup idle 1800 GHA_Remote-time

  vpngroup password KEY GHA_Remote

  I guess what I really wonder is if someone can convert the version of site to site of this VPN ASA 8.2 config so I can compare it to what I have. I need to have this, so I can just fall into place and work.

  Also, it does appear that political isakmp 40 are used, correct?

  On your ASA in Setup mode, simply type vpnsetup steps for remote access ipsec or vpnsetup site - not and it lists what it takes or you can download the PIX of the ASA migration tool.

• ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established

  Hi all experts

  We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?

  I got error syslog 713902 and 713903, how to fix?

  I got the following, when I type "sh crypto isakmp his."

  Type: user role: initiator

  Generate a new key: no State: MM_WAIT_MSG2

  Hugo

  Hello

  This State is reached when the policies of the phase 1 do not correspond to the two ends.

  Please confirm that you have the same settings of phase 1 on both sides with the following commands:

  See the isakmp crypto race

  See the race ikev1 crypto

  Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.

  Finally, make sure you have a route suitable for the remote VPN endpoint device.

  Hope that helps.

  Kind regards

  Dinesh Moudgil

• Router vpn site to site PIX and vpn client

  I have two on one interface on the pix vpn connections that terminate VPN. client vpn and VPN site-to-site have passed phase one and two and decrypt and encrypt the packets. However as in another post I can not ping through the l2l vpn. I checked this isn't a nat problem a nd two NAT 0 on the pix and the NAT on the router access lists work correctly.

  ISAKMP crypto RTR #show its
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  66.x.x.x 89.x.x.x QM_IDLE 2001 0 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  local ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
  current_peer 66.x.x.x port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: 23583, #pkts encrypt: 23583 #pkts digest: 23583
  #pkts decaps: 18236, #pkts decrypt: 18236, #pkts check: 18236
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  #send 40, #recv errors 0

  local crypto endpt. : 89.x.x.x, remote Start crypto. : 66.x.x.x
  Path mtu 1380, ip mtu 1380, ip mtu BID Dialer0
  current outbound SPI: 0xC4BAC5E (206285918)

  SAS of the esp on arrival:
  SPI: 0xD7848FB (225986811)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 3, flow_id: Motorola SEC 1.0:3, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4573083/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xC4BAC5E (206285918)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 4, flow_id: Motorola SEC 1.0:4, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4572001/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  Expand the IP NAT access list
  10 deny ip 192.168.2.0 0.0.0.255 192.168.10.0 0.0.0.255 (21396 matches)
  20 permit ip 192.168.2.0 0.0.0.255 everything (362 matches)
  Expand the IP VPN_ACCESS access list
  10 permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255 (39724 matches)

  I looked on the internet and that it points to a routing error when packets are being encrypted and decrypted, but you can't do a ping on the binding. However when I test the connection I did not enter any of the static routes that networks are connected directly on each side of the pix and the router. any help would be a preciated as I think there's maybe something is blocking the ping to reach the internal network at the end of pix with a configured access list.

  is ping failure of the only thing between the site to site VPN? and assuming that all other traffic works fine since it decrypts and encrypts the packets.

  If it's just ping, then activate pls what follows on the PIX:

  If it is version 6.3 and below: fixup protocol icmp

  If it is version 7.0 and higher: select "inspect icmp" under your political map of the world.

  Config complete hand and on the other could help determine if it's a configuration problem or another problem.

• Site to Site VPN between PIX and Linksys RV042

  I am trying to create a tunnel between a 506th PIX and a Linksys RV042 vpn .  I configured the Phase 1 and Phase 2 as well as the transformation defined and interested traffic and connected to the external interface, but it will not create the tunnel.  Configurations are as follows:

  506th PIX running IOS 6.3

  part of pre authentication ISAKMP policy 40
  ISAKMP policy 40 cryptographic 3des
  ISAKMP policy 40 sha hash
  40 2 ISAKMP policy group
  ISAKMP duration strategy of life 40 86400
  ISAKMP key * address 96.10.xxx.xxx netmask 255.255.255.255
  access-list 101 permit ip 192.168.21.0 255.255.255.0 192.168.1.0 255.255.255.0crypto map Columbia_to_Office 10 ipsec-isakmp
  crypto Columbia_to_Office 10 card matches the address 101
  card crypto Columbia_to_Office 10 set peer 96.10.xxx.xxx
  10 Columbia_to_Office transform-set ESP-3DES-SHA crypto card game
  Columbia_to_Office interface card crypto outside

  Linksys RV042

  Configuration of local groups
  IP only
       IP address: 96.10.xxx.xxx
  Type of local Security group: subnet
  IP address: 192.168.1.0
  Subnet mask: 255.255.255.0

  Configuration of the remote control groups
  IP only
  IP address: 66.192.xxx.xxx
  Security remote control unit Type: subnet
  IP address: 192.168.21.0
  Subnet mask: 255.255.255.0

  IPSec configuration
  Input mode: IKE with preshared key
  Group Diffie-Hellman phase 1: group2
  Phase 1 encryption: 3DES
  Authentication of the phase 1: SHA1
  Life of ITS phase 1: 86400
     
  Phase2 encryption: 3DES
  Phase2 authentication: SHA1
  Phase2 life expectancy: 3600 seconds
  Pre-shared key *.

  I'm a novice on the VPN. Thanks in advance for your expertise.

  Yes, version PIX 6.3 does not support HS running nat or sh run crypto.

  Please please post the complete config if you don't mind.

  Please also try to send traffic between subnets 2 and get the output of:

  See the isa scream his

  See the ipsec scream his

• Unable to pass traffic between ASA Site to Site VPN Tunnel

  Hello

  I have problems passing traffic between two ASA firewall. The VPN tunnel is up with a dynamic IP and static IP address. I have attached a diagram of the VPN connection. I'm not sure where the problem lies and what to check next. I think I have all the roads and in the access lists are needed.

  I've also attached the ASA5505 config and the ASA5510.

  This is the first time that I've set up a VPN connection any guidance would be greatly appreciated.

  Thank you

  Adam

  Hello

  Regarding your opinion of configuration Remote Site ASA that you have not added the internal networks of the Central Site VPN L2L configurations at all so the traffic does not pass through the VPN.

   access-list outside_1_cryptomap extended permit ip 10.1.1.0 255.255.255.128 10.182.226.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 10.182.226.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 10.182.0.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 192.168.170.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 192.168.172.0 255.255.*.* access-list exempt extended permit ip 10.1.1.0 255.255.255.128 140.15.0.0 255.255.*.* 

  Take a look at ACL configurations above. The 'exempt' ACL is used in configurations NAT0 and tells the ASA what traffic of exempting from NAT. "outside_1_cryptomap" ACL is used to tell the traffic between the subnets should be using the L2L VPN connection.

  So in short on the Remote Site ASA these ACLs should be identical. Make additions to the LIST of VPN L2L, then try again.

  I would also like to point out that to ensure that the Central ASAs L2L VPN ACL Site contains the same networks. The ACL on the Central Site will, of course, its internal subnets as the source and the site LAN remote destination.

  THW out of ' crypto ipsec to show his " shows you that only the SA between binding Site Central network and the Remote Site LAN was established. Others have not formed as the configuration is lacking at LEAST on the Remote Site ASA. Can also be the Central Site.

  -Jouni

• ASA Site to not tunnel no transmission of traffic for some subnets after awhile

  Hello

  We have a question really strange tunnel from site to site on several ASAs.

  We organize VPN tunnels between a small site and three largest.

  The den has an ASA 5505, the other three principles are ASA 5510.

  One of the tunnels working for months without problems.

  Each tunnel has several class C network.

  example Site:

  -192.168.50.0/24 (named A1)

  -192.168.51.0/24 (called A2)

  Site b:

  -192.168.60.0/24 (named B1)

  -192.168.61.0/24 (called B2)

  On two faulty tunnels, all is well at the beginning. After a few days (1-14) some networks to cease to work. So I can ping both A1 and A2 B1 network networks, but only from A2 B2 network. Pings from A1 to B2 doesn't expire. The ASA site showed tx = 0 traffic for <=>A1, B2, but progressive count rx traffic. ASA b it shows rx = 0 to B2<=>A1 and tx counties upward.

  This happens unexpected after different periods. Sometimes he hits ASA on site B, where tx = 0, it is sometimes ASA on A site.

  I tried to fix it as a result of orders:

  ISAKMP crypto claire his
  clear crypto ipsec his
  clear xlate

  but nothing has worked. The only solution for now is to restart the ASA where tx County indicates 0. After restarting, everything goes well for a while.

  On one of the affected sites, we have a failover configuration - ASA. A failover of the active device also solves the problem. But if you change your prior back restart the old principal question will return immediately.

  I think that there is no configuration because:

  -All tunnels are configured in the same way, and one of them is running for moths without any problem

  -Tunnels work for all combinations of subnet after a reboot

  -The problem occurs after different and long periods of time. So I think that the period between failures is long to be caused by tunnel a.s.o. timeouts.

  All ASA are running 9.1. (5) 21.

  I updated the firmware of several releases these past few months and had the same problem with any version I tested.

  So I hope that someone else has also had this problem and found a solution.

  Christian Hey!

  Hopefully, solve or find the root cause?

  Thank you

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Cannot delete the history and Top Sites

  Hello

  I use Firefox Mobile 26.0.1 on a Fairphone with Android 4.2.2.
  I am fully aware of how I have to delete the history (and Top Sites):
  Settings-> privacy-> clear-> private data (select all) clear data

  After doing this, I have not even alert "PrivΘes deleted" pop up, but it has no effect. All sites of history and high are still there.

  I just UN - and reinstalled the app of the in-game store, so there should be no modules are no longer. Previously, I had installed "CleanQuit" app.
  (https://addons.mozilla.org/de/android/addon/cleanquit/)
  It erases the history to the closure of Firefox which has worked well.
  But I can't delete the history in the way described above...

  Best regards
  Dieter

  Hi again,

  I just watched another question, I've had with entries Add on endangered in the menu. I found this is the bug 832990.

  After you turn off the checkbox 'do not keep activities' in the developer settings, I'm now able to clear history as it should!

• After the upgrade to the new version of firefox 13.01 I can't play video on youtube and other sites what should I do?

  After the upgrade to the latest version 13.0.1

  I can't open videos from youtube and other sites

  I tried all the solutions, but none works

  I would also consider the following. Recent crashes of some multimedia content (this includes the Youtube videos, some flash games and other applications), in collaboration with Firefox 13 are probably caused by a recent update of Flash 11.3 and/or Real Player browser plugin to malfunction.

  To resolve this problem, follow the steps in these articles in the Knowledge Base:

  Flash Plugin - maintain and troubleshoot

  Adobe Flash plugin has crashed - avoid that it happen

  11.3 Flash does not load video in Firefox

  We'll find other information on more technical issues under these links:

  http://forums.Adobe.com/thread/1018071?TSTART=0

  http://blogs.Adobe.com/asset/2012/06/inside-Flash-Player-protected-mode-for-Firefox.html

  Please tell us if it helped!