Minimum memory on ASA5585 for ASA OS 9.1

Similar Questions

• Home minimum memory for HA?

  The minimum memory for ESXi should be 2 GB of RAM, but I wonder if it's enough for the performance of the HA Agent? He failed on the two test ESXi with 2 GB of RAM to configure HA and something error messages made me suspect lack of RAM. After you have added up to 2.5 GB of memory through HA.

  So my first question is: all amount of RAM minimum on a host for HA to work?

  On the same cluster with these two small ESXi servers, I noticed that the size of the slot was about expected, something like 256 Mhz and 360 MB of RAM. HA setting = tolerate 1 node and small running virtual machine only. Which was quite strange for me was the the advanced Runtime Info reported only 1 single location across the cluster and when making a HA test with power off of a host, the virtual machine has not failed to wire and HA ' not enough resources for failover VM"or similar. Why this might be happening? HA expects more RAM available?

  HA requires 2 300 MB memory allow. If you have less than this amount, you will get an error when trying to activate HA.

• Chrombook L2TP/IPSec for ASA 5510

  Hello

  I have trouble getting a chromebook to establish a remote access connection VPN using L2TP/IPsec for a Cisco ASA 5510 12 7.2 (5) running.

  Run a debug crypto isakmp 5 I see the following logs (ip changed...)

  Jan 06 09:58:06 [IKEv1 DEBUG]: IP = 1.1.1.1, Oakley proposal is acceptable

  Jan 06 09:58:06 [IKEv1 DEBUG]: IP = 1.1.1.1, IKE SA proposal # 1, turn # 1 entry overall IKE acceptable matches # 4

  Jan 06 09:58:06 [IKEv1]: IP = 1.1.1.1, connection landed on tunnel_group DefaultRAGroup

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, status of automatic NAT detection: remote endpoint IS behind a NAT device this end is NOT behind a NAT device

  Jan 06 09:58:06 [IKEv1]: IP = 1.1.1.1, connection landed on tunnel_group DefaultRAGroup

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, previously allocated memory of liberation for permission-dn-attributes

  06 jan 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, PHASE 1 COMPLETED

  Jan 06 09:58:06 [IKEv1]: IP = 1.1.1.1, Keep-alive type for this connection: DPD

  Jan 06 09:58:06 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 1.1.1.1, timer to generate a new key to start P1: 8100 seconds.

  06 jan 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, PHASE 1 COMPLETED

  Jan 06 09:58:06 [IKEv1]: IP = 1.1.1.1, Keep-alive type for this connection: DPD

  Jan 06 09:58:06 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 1.1.1.1, timer to generate a new key to start P1: 8100 seconds.

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, data received in payload ID remote Proxy Host: address 3.3.3.3, 17 of the Protocol, Port 1701

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, data received in payload ID local Proxy Host: address 2.2.2.2, 17 of the Protocol, Port 1701

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, detected L2TP/IPSec session.

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, QM IsRekeyed its not found old addr

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, static checking Card Crypto, check card = outside_map, seq = 1...

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, static checking Card Crypto Card = outside_map, seq = 1, ACL does not proxy IDs src:1.1.1.1 dst: 2.2.2.2

  Jan 06 09:58:06 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 1.1.1.1, only Tunnel UDP-encapsulated and UDP-encapsulated-Transport mode NAT-Traversal-defined selection

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, remote peer IKE configured crypto card: outside_dyn_map0

  Jan 06 09:58:06 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 1.1.1.1, ITS processing IPSec payload

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, proposals of any IPSec security association has deemed unacceptable.

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, error QM WSF (P2 struct & 0x3d48800, mess id 0xce12c3dc).

  Jan 06 09:58:06 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 1.1.1.1, history of mistake IKE responder QM WSF (struct & 0x3d48800) , : QM_DONE EV_ERROR--> QM_BLD_MSG2 EV_NEGO_SA--> QM_BLD_MSG2, EV_IS_REKEY--> QM_BLD_MSG2, EV_CONFIRM_SA--> QM_BLD_MSG2, EV_PROC_MSG--> QM_BLD_MSG2, EV_HASH_OK--> QM_BLD_MSG2, NullEvent--> QM_BLD_MSG2, EV_COMP_HASH

  Jan 06 09:58:06 [IKEv1]: Group = DefaultRAGroup, IP = 1.1.1.1, removing counterpart table correlator failed, no match!

  1.1.1.1 = address remote chromebook NAT

  2.2.2.2 = ASA 5510 acting as distance termintaion access point

  3.3.3.3 = Chromebook private address

  I noticed that the Chromebook is appearing as the ID of the remote proxy but later, he seeks the applied to the Chromebook NAT address.  Not sure if this is the cause or how to solve this problem, if it is.

  Can someone advise please

  Thank you

  Ryan

  7.2 is old code.  You can re - test with 9.0.x or 9.1.x.

  https://support.Google.com/Chromebook/answer/1282338?hl=en

• I have a strange problem with my RAM supported by installers. When I check the activity monitor, 3 installers are open and they start around 80 MB memory RAM used for about 7 or 10:08 minutes or so.

  I have a strange problem with my RAM supported by installers. When I check the activity monitor, 3 installers are open and they start around 80 MB memory RAM used for about 7 or 8 concerts after 10 minutes. I have to force them to quit, but I don't know what I am closing or why they open in the first place. Applications downloaded on iTunes?

  

  In addition, the Console has opened with the same message several times, but I don't know what that means.

  Any help would be appreciated.

  Hello

  The last is a picture of the Terminal window.

  Just because it lists 'Console' does not mean that it has nothing to do with this application.

  You have not said why or what you're trying to install so I can't help with that.

  You can use the activity monitor to leave their.

  After you select an item, use the X in a type of stop sign icon and confirm force quit.

  

  21:36 Thursday; September 15, 2016

   iMac 2.5 Ghz i5 2011 (El Capitan)
   G4/1GhzDual MDD (Leopard 10.5.8)
   MacBookPro (Snow Leopard 10.6.8) 2 GB
   Mac OS X (10.6.8).
   iPhone and iPad (2)

• What files are identified as "Other" in memory when checking for storage?

  What files are identified as "Other" in memory when checking for storage?

  All files that are not in the categories with names.

• Upgrade memory 667 Mhz for Satellite U300

  Hello

  I have a new Satellite u300-11v and I was hoping to upgrade the memory standard modules of current 2 x 1 GB 2 x 2 GB ddr800 for a max speed of memory. However, after looking at intels site for specifications of the chipset for my machine (its got an intel mobile GM965 chipset) it seems that it will only support up to 667 mhz RAM modules.

  Reading a little further, I think that if I have a memory at 667 mhz bus it can only be reached through the module 1 x 2 GB at 667 mhz. Currently I put 2 x 2 GB 667 modules in the machine, the default memory bus at 533 mhz.
  I watched chipset specs of your laptop (945GM) while I was on the site intels and your in the same boat as me.

  Heres so the dilemma: you have just 1 x 2 GB 667 MHz memory to get this speed little extra memory or go for 2 x 2 GB to the slowest to 533 mhz to accommodate all these massive windows page file.

  For me, have family Vista premium running on a machine that can bring together only a bus 533 mhz memory with 4 GB of ram is not acceptable while I will now go back to XP pro which is not so heavy on resources.

  Did you really notice the difference between the memory 533 MHz bus and memory 667 MHz modules?

  Of course, there is a small difference in performance, but you will never get a performance gain by using the modules of 667 MHz instead of 553 Mhz modules.

• the memory of maxim for (AOD270-1596)-

  the memory of maxim for (AOD270-1596)-

  AND what is the maxmum only added to mini computer laptop 10.1 memorey "

  The Acer Aspire One D270 supports up to 2 GB memory DDR3 system.

• How can I check replacement memory is correct for the following laptop:

  I'm considering a purchase in the next 2 months of this device: HP ProBook 4530 s (XU016UT #ABA).  Is there a list indicating the memory that is compatible with this unit of the brand and model?  I'm looking at this particular unit: Corsair Memory - 8 GB (2 x 4 GB) DDR3 SODIMM Memory (CMSO8GX3M2A1333C9 The 4530 comes with Win 7 Pro 32 bit OS, so it will use more than 4 GB of memory.)  Thanks for any help you can offer.  Jim.

  Hi, Jim:

  This memory should work, but only 4 GB will be usable with a 32-bit operating system. You need a 64-bit operating system to take advantage of more than 4 GB of memory.

  When you receive your laptop, call HP at this number below and see if they will send you a W7 Pro 64 bit game of fast laptop restore disks and if you decide to install 8 GB of memory, you can install the 64-bit operating system.  You will need the model number and serial number handy.

  1-800-334-5144

  You can use almost no portable PC3-1333 ECC memory.

  This memory will work:

  http://www.Newegg.com/product/ProductList.aspx?submit=Ene&N=100007609%20600000414&IsNodeId=1&name=DDR3%201333%20%28PC3%2010600%29

  Paul

• Hello, I am looking for driver for card reader memory vgn-fz250e for win7 64-bit

  Hello, I'm looking for a driver for card reader memory vgn-fz250e for win7 64 bit, I downloaded all the driver on your Web site and try, buy does not work, can you tell me which one is right, thank you very much!

  Try this one from HP:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...

  Other people have said that the HP driver works fine with 64-bit Vista VAIO.  If it doesn't work no, just roll back the driver in Windows Device Manager.

• Cisco Anyconnect/WebVPN license for ASA 5510

  Hello

  Someone could please check the licenses for ASA 5510 attachment and let me know. We currently have ASA 5510 with basic license. According to the table attached under VPN sessions, he mentions that "250 combined SESSIONS IPSec and WebVPN" and to "Max box of WebVPN Session" it is mentioned that 2nd meeting, exceeding that we must buy license optional webvpn. While we the 250 combined license for IPSec and webVPN. We must purchase additional anyconnect license to set up remote access for users who want to use the internal resources from outside the network. OrElse, we don't have to purchase license and can configure webvpn/anyconnect of existing combined license existing users basic ASA license? Waiting for your response. Thank you.

  You are welcome.

  1 Yes

  2 AnyConnect requires no Java, but it can he use when connecting to one AnyConnect SSL VPN client and launch the Web browser option start Java-based. There was a bug with the AnyConnect old versions had later who should have addresses. You also have the option to launch via IE and using ActiveX or simply throw AnyConnect directly - neither of these two methods require Java.

  Here is a document TAC on the Java questions if you want more details.

  Please take a moment to note the useful messages and mark your answers questions.

• GANYMEDE for ASA 5550

  Hello

  How to configure Ganymede for ASA 5550 with acs4.2. I have two asa, one is active and others in mode. pls tell me how to set up. I couldn't find any good docs either.

  Thank you.

  Hi Gavin,

  Here is the sample config for ASA's telnet authentication from Tacacs: username admin password xxxxx privilege 15 aaa-server TEST protocol tacacs+ aaa-server TEST (inside) host x.x.x.x  yyy   [x.x.x.x is the ip address of the tacacs server and is reachable from the inside interface and yyy is the shared secret key.] aaa authentication telnet console TEST LOCAL   [This will send the telnet authentication request to the tacacs server first and if it is not reachable then use the local database of the ASA] aaa authentication ssh console TEST LOCAL    [same as above but for ssh session] aaa authorization exec authentication-server    [this enables exec authorization for the telnet and ssh sessions.] 
  aaa authentication http console TEST LOCAL [for HTTP]
  order of accounting AAA TEST [this helps accountants of the order for all orders entered in the telnet or ssh session.]  On the Ganymede server we need to add this ASA as a RADIUS client with shared secret key yyy.
  
  You can find more details: -.
  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/mgaccess.html#wp1042026
  The GBA, you need to add ASA as device under config network with Protocol Ganymede.
  Thank you
  Vinay
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
  		   

• How much memory is needed for WebAnalysis

  Hello
  
  Can anyone suggest me the amount of memory required for Hyperion WebAnalysis?
  
  Please send the link for equipment transportation of WA (if any) as well.
  
  Thank you

  Hello

  Pls find the link of the support for Hyperion System 9.3.1 matrix-

  http://download.Oracle.com/docs/CD/E10530_01/doc/EPM.931/hsys9_install_start_here.PDF

  Analysis Web is a web Client and use the power of the server. It is preferable that the Hyperion server must have good memory configurtion (2GB) for best performance.

  Hope this will help you.

  Thank you best regards &,.
  Jeanbaptiste

• Can I put in my minimum memory of the Satellite C660 - 1 M 4 for Intel Hd Graphics?

  There in no option in BIOS v 1.9. I just need for simple game, but there are a few problems with the onboard graphics with dynamic memory. If there is an option to set a minimum usage of memory for Intel HD G propably the game would go.

  Thanks for help.

  JL

  As far as I know, everything runs automatically, and you cannot manually change the memory.

• InputStreams for HTTP [S] response data: confirm a minimum memory buffer/reading early?

  I need to manage data from a web service response. The format of the response data is under my control and is returned as a stream (net.rim.device.api.crypto.tls.TLSInputStream) to my BlackBerry application. The content of the feed is an XML stream that contains simple header information and then one or more 'chunks' of data. The data is compressed (gzip) and coded (Base64). BB app must decrypt, decompress, and then process the data in the stream. For the purposes of my application, I never need all of the data at a time; processing flow for real, that's what I'm looking for. I've implemented a pipe which, in pseudocode, looks like this:

  SecureConnection httpsConn; already implemented

  InputStream httpsStream = httpsConn.openInputStream ();

  InputStream compressedStream = new (Base64InputStream.decode (httpsStream));

  InputStream is = new GZIPInputStream (compressedStream);

  int aByte = is.read ();

  The goal is to put buffer in the bit data as possible so that the operation on the side of BB is not intensive memory as the data grows. The effective implementation of this pseudo code works very well.

  The question I have is: I can confirm that the httpsStream I have created from the httpsConn is completely not himself read the BB in the specific RIM code? In other words, if there are 20 MB of data in the stream, I don't want to know that the stream has read data HTTPS completely - 20 MB all - and then put at disposal. Instead, I want to know only as much data is consumed as I makes (is.read) as well as a small buffer, perhaps, for the effectiveness of the network. A third way to ask the question: I think that it is supposed to be the definition of a well implemented InputStream, but I'm having a hard time finding a definitive '' Yes, J2ME (or BB) InputStreams promise to read HTTPS data on request and not all at once.

  I expect tons of streaming audio and video apps are partial evidence that works real data on the fly on the Net.  Still, I left the details as XML processing by SAX - it's one on the behavior of the InputStream HTTP [S].  But it brings the fourth way to phrase my question: if I use SAX instead of a tool of DOM to treat my HTML because I want to monitor the pressures of large data flows, will I get cancelled by buffering I can't control in the low-level InputStream HTTP [S]?

  Before you say, ' HTTP [S] is not where you should make streaming ", this is not streaming in itself. It is instead one - possibly large - answer to a POST.  Highly 'typical' web interaction

  If changes in response based on the version of the OS, presumably 4.6 or better is the target platform.

  Thank you!

  -Del

  I don't remember the said documentation. All I remember is that I proposed of workaround to someone on this forum and they later confirmed that he has solved the problem of buffering (they were streaming audio as great answers HTTP - streaming started to work very well, without a lot of latency).

• Help on graphics card memory and upgrade for iMac

  Hello!

  I need advice on a good new graphics card for iMac 27 inch end 2012. My work is mainly in animation, Visual effects and game development soon, so I need an additional card to increase my speed.

  Currently, I have a NVIDIA GeForce GTX 680MX 2048 MB card. Do you think I should stick to a similar card? Is there something new that will offer me better performance at an affordable cost?

  I don't have much money to spend, but I can certainly use additional graphics now.

  I have also 2 remaining memory locations that accepts DDR3 1600 MHz memory module, but it seems that this module is no longer available. If I had to choose between a graphics card and RAM, which should I go with?

  Finally, can I install these myself? I don't have any Apple Store around me and I do not trust the computer guys in my area.

  First of all, the iMacs are notoriously difficult to make something with except add RAM. Here is a good site where you can get some info on the dismantling, etc.:

  https://www.iFixit.com/

  Usually, graphics cards should be replaced with the same model/type of work (if any) - see above site for this kind of info. I'm quite sure that you cannot add just one - iMac is not designed for it.

  Regarding the RAM, just check out OWC for necessary RAM:

  https://eShop.MacSales.com/shop/memory/iMac/2012_27/DDR3L

  Check that your model is listed. I don't know where you would have been told that the RAM is no longer available (FWIW, Apple does not sell RAM and uses of third party RAM in the new Macs).

  I'd go with the RAM - how many do you have now? Adding RAM is easy.