Missing COM1 on the cFP-2100

Similar Questions

• Uplink on the WLC 2100 series

  Hello

  I missed something in the Cisco WLC 2100 series documentation. In fact, the plug technical it is mentioned that the WLC 2100 "provides eight 10/100 Ethernet ports to support a combination of access points and rising redundant LAN", while in the configuration guide noted that the WLC 2100 supports no LAG (aggregation of links). So how WLC 2100 can use a redundant network connection without aggregation of links?

  Thank you in advance.

  You can use a port for management and interface ap - manager and another for the vlan specific used for the ssid of your wlan with connection of access points to your WLC. This way you can say that port 1 is your management and ap-Manager, port 2 is for your internal ssid vlan x, port 3 is for your voice ssid vlan x, port 4 is for the traffic of comments, 5 & 6 port is used to connect the two access points.

• View missed calls when the phone is off?

  Hello

  My phone turned off (or without service) incoming calls do not show on my list of missed calls.

  There may be a voicemail when my phone is back, but no match no missed calls.

  Is there a setting that will show you missed calls when the phone is off?

  Debra

  iPhone 6 s

  Once you turn back on your iPhone, all calls that occurred while the iPhone was off should appear in the Missed Call list.

  If they do not:

  • If you are in your area served by your cellular operator, contact your operator.
  • If you are outside this area (roaming), you can not see the calls until the return.  You could ask your cellular operator on this subject.

• missing text in the button Delete the bookmark.

  There is missing text in the button Delete the bookmark. The key works but the text is missing.

  Here is a screenshot of the problem:
  http://Tinypic.com/view.php?pic=dltkau & s = 8 #. U0rV96KrFEM

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Found 0 results for my browser missing important elements, the menu..., whole tool bar drop down to print, copy, work offline, file, save, bookmarks, history. I just installed latest foxfire on windows xp. Found a few instructions, but they called in the

  Found 0 results for my browser missing important elements, the menu..., whole tool bar drop down to print, copy, work offline, file, save, bookmarks, history. I just installed latest foxfire on windows xp. Found a few instructions, but they called the keys of my computer does not have (key under OSX there no file, edit, history, help, tools, navigation, all the things that your directions say to use. Also, I'm still hanging and the message a scrip is running. I don't know what are the thises scripts but I of course don't need them.

  This has happened

  Each time Firefox opened

  == I just noticed it. It probably happened when I upgraded foxfire.

  Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
  Turn on/off the menu bar is a new feature in version 3.6.
  (Linux and OSX see: what happened to the file, edit and view menus? )
  Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
  Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
  The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
  See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing

  Navigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).

  To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).

  Mode full screen
  http://KB.mozillazine.org/netbooks#Full_screen

  See also:
  Back and front toolbar buttons or others are missing
  Customize controls, buttons, and Firefox toolbars

• Satellite L750-1LC - Boot Manager is missing by using the recovery disk

  I bought a Toshiba satellite L750-1LC and I try to create the DVD 4 to save.

  On the first dvd that only he came an error reading twice, the other DVDs were ok.
  When I try to recover from the DVD the recovery process got stuck on the first dvd so I had to reboot and try again, but the same thing happened to it.

  After you restart the system it came a message that bootmnager is missing and windows and any other thing was gone.

  Is the promotion of "No. Matter What Guarantee" "covering this type of flaws?
  If so, what are the steps to qualify for this promotion?

  I said that I am a Romanian citizen and I have already implemented for promotion in the specified time interval.

  It seems that the first recovery disk is not created properly because you got an error message.
  As I understand your message, you have tried to boot from the first recovery disc (which was not correctly created in the past) and so the installation could not be completed successfully.

  Now, you cannot start the operating system, because the Boot Manager is missing and possibly the system is deleted also
  I see just one solution: order the new disk recovery from here and use it for the installation of the OS: http://backupmedia.toshiba.eu/landing.aspx

  PS: as far as I know that hardware issues are covered by the warranty, software issues not covered by the warranty

• Vibe X 3 Low Vibration, missing most of the reviews?

  Hi all

  I'm using this device more than 10 days and felt its Vibration is also much slower than any samsung and another phone while it is in my Pocket I missed most of the important alerts, etc., only get appeal warns when received a call because rintone plays at very high volume, which is a good thng...

  Im having always have to keep iphone4S with miss no alert, if it can be fixed then I'll getrid of keep two phone in the Pocket.

  However this bug has been fixed in update of Marshmallow, please upgrade your operating system if you are on lolipop yet...

• Missing Launchpad from the dock. How to restore?

  Missing Launchpad from the dock. How to restore?

  The Finder, choose Applications go to menu and get her back.

  (137799)

• Variables shared on the CFP becomes zero and communicate with the PSC

  I use a PC with two network cards, one on one wired ethernet, the other on a private IP directly connected to a PSC-2120 (running 6.0.5 full). I use variables shared on the CFP and aliasing to static variable on the PC (initially LV 8.6, now 2009f2 with the same problem in both). PC variables are stored in a database of the Citadel. I have the CFP program built to run at startup, and it works fine when not connected to the PC.

  When connected to the computer all variables shared on the CFP will from time to time (almost 1/min for a few seconds) and randomly becomes zero. Even if they are resized only not to allow to become zero. I can say that what is happening because I use the variables shared as relay alarm thresholds module, and relays to suddenly slam on. I confirmed this by checking that the CFP has written to its internal flash memory card, and indeed variables suddenly are nil. On the PC it says that it cannot connect with the shared variables. This happens although LabView is not running on the PC!  Manager distributed system variables shared on the CFP are listed as (disconnected) during this time, but it continues to be able to read the correct values to live of the CFP entered the module.

  Interestingly, I have the same computer with the same configuration (and a PSC-2120 different) that does not have this problem. Both PC's are new from the factory. I tried to disable the second ethernet adapter, closing all wall-lights/virusscan and re - order network cards in windows networking/advanced settings without success. Simply disconnect the cable between the PCP and the PC does not cause this problem and shared variables become zero does not trigger the network on the CFP monitoring parameters.

  My questions are:

  (1) this problem can be fixed?

  (2) lost communication for a few seconds is OK, but given the PSC variables become zero is not. Can I stop the variables of the PSC to become zero?

  -David

  To update my previous post, it turns out that the re-installation was not the solution (the problem of variables start again occurring began). I finally realized that this only happens when I put the CFP time server IP (under Additional Configuration to the MAX). I was upgrading the server time on 192.168.1.1 IP (the IP address of the adapter of the CFP has been directly connected to). However, this compensation setting solves the problem.

  I do not think that the time on the CFP must need to be addressed too often (and perhaps it is synchronized if I never re - deploy files to the CFP?), so I guess that leave it empty. Curiously, I have the same setup time on an another PSC server IP and PC (running LV 8.6) without problem.

  -David

• How can I detect dynamically new modules of the cFP-2200?

  Hello

  I'm working on a project that monitors the voltage using the cFP-2200 with any number of PSC-HAVE-102 installed modules. Each analogue channel PSC-HAVE-102 will correspond to its own state machine which tells you a central database.

  I want to create something that does not need to know how the PSC-HAVE-102 s settled in advance. At startup, my software must be able to detect all PSC-HAVE-102 s and dynamically create the State machines for each channel, if I have 1 I-102 (8 analog monitor channels), or the maximum of 8 installed (64 channels to watch).

  Right now, I can only understand how to the program for channels that are currently available by connecting to the module in its current condition and click/drag the analog channels in the project window. Is it possible to program for strings that are not there, but could be later? The application of this is to deploy the module on the ground and have the ability to add or remove I-102 s without changing the installed software.

  kgolden,

  Do you mean that the ini file will be correctly created only if I have the number I-102 s max?  Yes, you must have 8 I-102 in your project as part of the goal of the PSC.  Forcing him to be included in the. The IAK file and in turn to be defined in the .ini causes.  I think you can use the Project Explorer to add modules to the CFP, even if they do not exist physically.

  Is it possible to manually edit the file instead?  I think that it is possible to manually edit the .ini.  I don't know that NEITHER does not bear this manual change.  The question would be is there other on the CFP .ini files that contain references to the i/o modules installed?

• missing samples in the waveform graph

  Hello world

  When processing a file .wav into pieces, I noticed that there are missing samples on the waveform graph where two pieces must be met for the display. What could be the cause of this? Any help appreciated. Thank you!

  Milan

  Your method of reading in pieces in a for loop is create a table 1 d of waveforms with the tunnels of automatic indexation.  It is as well as what you have the data appear in different plots.  I don't know if that's what you want.

  But if this is the case, the problem is that you get to the last point of the first plot, and the first point of the next parcel is a different value.  Because they are two different plots that you do not get the line to join them, as you do between points that are part of the same plot.

• Missing VI on the new laptop

  When I tried to open the vi in a new laptop, it will signal missing vi as the attached screenshot.

  It seems of NIscope, so I installed and try again, but still the same.

  I use LV2009, suggestions, thank you.

  Instead of trying to copy the files from niScope, I think install would be better.

  You probably have the drivers on DVD, or you can download them from the Web site of NOR: http://joule.ni.com/nidu/cds/view/p/id/1492/lang/en

• How to program the CFP-1808 via serial port?

  Dear Sir/Madam,

  I am studying this topic shows CFP-1808. I work as for the Department of mechanical engineering, University of Moratuwa. It is therefore want to do a practicle using PSC for the last year students of tha. First of all, I have to study. Today I try it.

  Now I know how to read and write the DI and DO it via the serial port. As I know that the programming of LabVIEW. But now I don't know how programs of labview download to the cFP-1808 through the port series. I want to say is "I want to help you how to make a simple exercise. Average easy, it can be a logical operation. ». It is very important to continue my work. He would be grateful if you can send a positive response to this problem, thank you,

  Mohamed Ahmed (B.SC. (Eng)),

  RA,

  Department of mechanical engineering,

  University of MOratuwa.

  
  

• How to detect the cFP-1804

  Hello

  I have a cFP1804 connected to a cFP2120 via EThernet.  The cFP1804 has a thermocouple installed package that is read once per second the 2120 by using the 'FP Read.vi"(see file attachment). When systems are interconnected, the correct values of returns «FP read» When disconnecting from the cFP1804, "PS read" still will continue to serve the received values but triggers error 33800 until the connection has been restored. So far so good.

  The problem I have happens when you reset the cFP2120 while the cFP1804 is offline. At that time a single "FP read.vi' will cause the program running on the cFP2120 to stall completely.

  No idea how to get around this problem?

  I'm using Labview 8.2.1 with RT version 5.0.1

  Thank you

  V

  Hi Volker,

  You can detect the RT and network objectives using the replication VI system. An explanation can be found in NI Developer Zone tutorial: replication of system of target in real time at http://zone.ni.com/devzone/cda/tut/p/id/3937. The download link is at the bottom of the page. Be sure to read the included Readme for installation instructions. If you run the VI find all targets, you will be able to test if the cFP-1804 is on the network.

• How can I re - install Windows XP on my daughters PC where the product key is missing half on the sticker?

  Hello
  I have the original from my window xp I want to put it on my lap top girls but the number of product is half missing, is in the same House since when I recorded my own can I put it on more tham 1 pc in the same household?  If so, how can I get the number, when I ring to activate, it is for me as a no, I may have a pirate copy, but it's mine
  Thanks in advance
  original title: activating xp

  If your copy of Windows is preinstalled on a computer, it's an OEM copy - and the license CANNOT be transferred to another computer.

  Nobody don't keep records of this license has been actviated by which - above all, Microsoft. Data for registration and Activation are stored on separate servers and correlate precisely for this reason.

  Each license of the retail XP DO can be installed that on one machine at a time - the OEM licenses are not transferable between machines.