Missing unknown device after the upgrade of windows 8 to 8.1 pro

Similar Questions

• Unknown device after the upgrade to windows 8

  I don't know if it's a Windows problem or a problem of HP. HP says windows. But in any case, I have a HP Pavillion M7 nine 1015dx notebook pc and I just upgraded to windows 7 to Windows 8 do a clean install. After you have installed all the appropriate drivers update my site of PC makers, I have an "unknown device" in Device Manager that I can't find a driver for. I tried several different avenues to get a driver for this thing that I don't know what it is. The hardware Id are:

  ACPI\VEN_HPQ & DEV_6001
  ACPI\HPQ6001
  * HPQ6001

  I contacted HP support and they say it's a Windows problem. Also I have when I activate secure boot and try to start I get a BSOD immediately. I'm not sure but I think that these two problems are related. Any help is very appreciated.

  Thank you

  James Pack

  Wallaaaa... bravo and congratz to BartoszZalewski... problem solved... it touches just only wireless! arghhhhhh just a forgotten by HP to put hahhaha.

  ___________________________________________________________________________________

  Maybe it's the solution to our problem :)

  SUPPORTED DEVICES:

  ACPI\HPQ6001 = "HP wireless button Driver.

  ACPI\VEN_HPQ & DEV_6001 = "HP wireless button Driver.

  Link to the device driver: http://ftp.hp.com/pub/softpaq/sp58501-59000/sp58720.exe

• Missing graphics drivers after the upgrade to Windows 8?

  Hey guys,.

  I see several people on the forums of the problems with graphics drivers not installed after the upgrade to Windows 8.

  The first step you want to take, make sure that the laptop is supported by Windows 8.

  You can go HERE and see if your laptop has been tested for Windows 8. If she's GREAT!

  Now, if you're still looking for the graphics drivers according to the processor you have there are several places to look.

  First of all, you want to check the HP website and your product type # in the next selection > and then select the operating system > click Next > and look under the section that says "Driver - Graphic" and start the download.

  If you still don't see the driver referred to in this article, you can see one of these sites according to what processor you have.

  INTEL

  AMD

  Also, if you have Windows 7, you can still follow this post.

  THX

  I hope it's useful!

  THX

• Unknown devices during the upgrade to Windows 8.1 on my Envy 15 t-j000

  I've upgraded to 8.1 Windows, but my Envy 15 t-j000 shows 3 mistakes of devices in the section "other devices."

  They are as follows:

  PCI device (location: bus 9 PCI, device 0, function 0)

  PCI\VEN_10EC & DEV_5227 & SUBSYS_1963103C & REV_01
  PCI\VEN_10EC & DEV_5227 & SUBSYS_1963103C
  PCI\VEN_10EC & DEV_5227 & CC_FF0000
  PCI\VEN_10EC & DEV_5227 & CC_FF00

  Unknown device (location: on Microsoft ACP-I compatible system)

  ACPI\VEN_HPQ & DEV_6001
  ACPI\HPQ6001
  * HPQ6001

  Unknown device (location: on PCI Express Root Complex)

  ACPI\VEN_HPQ & DEV_6007
  ACPI\HPQ6007
  * HPQ6007

  Anyone know how I can udpdate drivers for these devices?

  Thank you

  Hello:

  Here are links to the drivers you need:

  PCI\VEN_10EC & DEV_5227:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123976-1&cc=us&DLC=en&LC=en&OS=4158&product=5388047&sw_lang=

  ACPI\VEN_HPQ & DEV_6001:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123643-1&cc=us&DLC=en&LC=en&OS=4158&product=5388047&sw_lang=

  ACPI\VEN_HPQ & DEV_6007:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-124661-1&cc=us&DLC=en&LC=en&OS=4158&product=5388047&sw_lang=

• Missing music files after the upgrade to Windows 10

  Original title: windows media player

  What happened to all my music files I had Windows 7 when upgraded to windows 10?

  Did you do an upgrade on the spot to W10, or did you do a complete new reinstall?

  Makes you backup data before hand?

  If you did an upgrade in Place your music files should still be there. If you did a clean installation from scratch, they will have been removed.

  If you have made a backup before hand (always recommended) or if you have a recent backup, you should be able to restore that. Also, if all goes well, there will be a folder "windows.old" on your PC, which must contain your old music files in folders that they were originally in. Find the folder "windows .old" and navigate in Explorer windows (not IE) to see if you can find them. If you can COPY them to where you want.

• Error - missing operating system after the upgrade to Windows XP Professional from Windows XP Home Edition.

  Original title: lack of an operating system.

  I have a Dell which had windows xp home installed on it I upgraded a while back to pro, the problem is the operating system that you are completely crushed and all I have is a cd to upgrade so it won't let me install because it said that missing operating systems... so what can I do that won't cost me a thing!

  Hi mistyblu976,

  This problem may occur if one or more of the following conditions are met:

  (a) basic input/output system (BIOS) does not detect the hard drive.

  (b) the hard disk is damaged.

  (c) sector 0 of the physical disk has an incorrect or malformed master boot (MBR) record.

  You can follow this link & check if it helps.

  "Operating system not found" or the "Missing operating system" error message when you start your Windows XP-based computer

  Hope the helps of information. Please post back and we do know.
  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to restore missing zip folder after the upgrade to windows vista home premium 32-bit 7

  restore the zip folder

  Hello

  How to disable Windows Explorer folder in Windows 7 Zip folder view, see option 2
  http://www.SevenForums.com/tutorials/13619-zip-folders-enable-disable-Windows-Explorer-view.html

  ==================================

  If you need more features/functions an excellent 3rd party utility is 7-Zip - free

  7-zip - free
  http://www.7-zip.org/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• After the upgrade to windows 10 missing MSCVP110.dll

  Hello

  After the upgrade to windows start 10 lack MSCVP110.dll and no app.

  I have uninstall and install redist visual x 86 and x 64, but it's the same thing.

  Help!

  Hi ambredoreau,

  There is a specific problem of windows OS, I will recommend you to contact windows support team.

  But I found a useful link, please relate to her Halo Spartan Strike - MSCVP110.dll - Microsoft community.

  Check out this link Windows 10 and Adobe Creative Cloud for application compatibility.

  Kind regards

  Nicos

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• Volume controls on the keyboard after the upgrade to Windows 8

  I have a Touchsmart 520-1070 with the mouse and keyboard without wire factory.  After the upgrade to WIndows 8, the volume controls no longer work.  I tried the Recovery Manager to reinstall the keyboard drivers, but there is no driver keyboard under hardware drivers.

  In the following device manager are listed under keyboards:

  HID keyboard device

  Keyboard 109 MCIR Microsoft eHome

  Keyboard MCIR Microsoft eHome

  Microsoft eHome key remove control Keayboard

  PS/2 standard keyboard

  Any report that they are installed and are working correctly and that the drivers are up to date.

  Has anyone else seen or solved this problem with a Touchsmart computer?

  The instructions below were provided by HP support.  This has restored the function on the keyboard volume controls.  The referenced below drivers are drivers IDT high definition Audio Device.  I am not sure that it was necessary to reinstall the audio drivers.  It can only had to remove the USB dongle and back to restore the functionality of the button.  Note: the USB dongle is located behind the VESA Panel to the back of the PC.  No tools are required and the dongle can be removed and replaced without shutting down the PC.  VESA panel removal requires a bit of a steady hand, pulling the lip which is close to the connections on the rear panel.

  Instructions received from HP:

  Please go to the following link and check the "return of the system", article #7 is the USB dongle:

  http://support.HP.com/us-en/document/c03026390

  After you have reinstalled the receiver, please download and install the following driver:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-110499-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

  Then install the following update:

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=CP-112060-1&CC=US&DLC=en&LC=en&os=4132&Product=5157120&sw_lang=

• Laptop Compaq CQ58: LAN Ethernet does not work after the upgrade to windows 8.1

  After the upgrade of Windows 8 to 8.1, my Ethernet LAN is no longer in effect. Wireless LAN connectivity is OK. I run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I don't see a listed 8.1 for the LAN Ethernet driver.

  It seems that you encounter the same problem, I did when I ran the free preview of the W10. I had this error on the card reader.  I have no idea how to solve this problem.

  Is there is no ethernet controller needing drivers in Device Manager, then it is probably the realtek lan adapter that has the number 12 of the code, or it is part of the motherboard that controls the ethernet adapter.

  If you need Atheros bluetooth driver, then this is probably the one you need.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_127984_1

  Unfortunately, I won't be able to help you with question 12 code or ethernet.

  IMO, they are insoluble.

• Cannot connect to internet after a reboot before you uninstall and then reinstall the network card. (After the upgrade to Windows 7 from Vista)

  This problem started immediately after the upgrade to Windows 7 Ultimate (32 bit) to Windows Vista Ultimate (32 bit).  Again, I want to remind that I never had this problem before installing Windows 7.

  -After a reboot, I am presented with the impossible to connect the network indicator (yellow triangle with!) in the task bar.  (It was how I was welcomed after the installation of Windows 7 is said by the way).

  -The only way I found to regain connectivity is to uninstall and reinstall the network via the device manager card, date at which the computer always successfully connects and remains connected until the next reboot.

  Network card: Realtek RTL8168C (P) / 811C (P) Family PCI - E Gigabit Ethernet NIC (NDIS 6.20)

  Driver provider: Microsoft
  Driver date: 14/05/2009
  Driver version: 7.2.1127.2008
  Digital signer: Microsoft Windows

  Thus, we have solved the problem! There are two possibilities of your problems:
  1 company Adobe uses the Bonjour service , this service should be disabled.
  Computer > Manage > Services and Applications > Services => find the bonjour service (sometimes stated as long numbers), stop service and if the Disabled value. It works!

  2. If it is not signed as Bonjour service. Try to disable the service:
  Shutdown mDNSResponder .exe (he is represented by # Id_String1.6844F930_1628_4223_B5CC_5BB94B879762 #).

  It is installed with Adobe software. If you upgrade the Vista, it will generally many users problem!

• HDR and Panorama fail after the upgrade to Windows 10

  After the upgrade to Windows 10, trying to merge pictures gives the message "unknown error occurred".  After the first attempt, I've updated my driver graphic card, and HDR worked.  But the next time, the error message reappears, and this has been consistent - if the graphics card is engaged or disabled!  My graphics card is NVIDIA GeForce GT 750 M.

  The problem turned out to be unrelated to Windows 10.  For reasons I can't understand, it is limited to one set of photos taken on a single morning. So, no problems with Windows 10.

• FN keys do not work after the upgrade to Windows 10

  Why the FN keyboard does not work after upgrade to Windows 10?

  FN keys are controlled by utilities and special tools of Toshiba. Usually after the upgrade to Windows 10, the parts of the pre-installed Toshiba software must be upgraded to version compatible and support Windows 10...

  You have not provided information on the laptop model so I can't say with certainty if your unit is 10 Windows supported or not...

• Satellite P855 - function keys do not work after the upgrade to Windows 10

  Function keys do not work after the upgrade to Windows 10
  I know that I need two drivers (Flash cards support utility) and (Toshiba function Key Utility), but on the page download Toshiba is not suitable for Windows 10.
  Anyone know when and if it will be available?
  Thank you

  I'm also waiting for Win10 of things and do not know with certainty how Toshiba will start with the support of Win10. I hope that will happen soon.