MSE does not work.

Similar Questions

• Cisco MSE 8510 MCU - comments PIN does not work

  Hello

  We have a few conferences on 8510 blade. Each conference is the main AXIS and the comments set up PIN. When I dial in the Conference, main SPINDLE works fine but the PIN prompt does not work.

  I tried to deal with the PIN of an endpoint, then the guest PIN from the other end, but the Conference does not accept the feedback PIN. I can use the good main SPINDLE on the two end points.

  Anyone know what may be the issue?

  I just tested this without 8510, no problem at all.

  Can you give us a screenshot of the configuration of your conference?

  I had used the same digital ID for Chair and comments, with a different PIN for each.  When I connected as Chairman, I went straight in.  When I connected as a guest, I went straight in, but I got a quick saying saying President to arrive or to connect.

• my laptop pointer freezes sometimes and does not work properly

  I have a sony vaio notebook. This pointer does not work properly most of the time, and it freezes. I have to restart my computer to fix it temporarily, but it happens again and again. I wonder if my system is infected with a virus or not. can fix this or I need to recover my laptop. I look forward to your reply. Thanks indeed

  Try to go to the sony web site and get the last mouse and mouse pad drivers.

  If an external mouse, clean and check the batteries if applicable.

  If this isn't an external mouse, try an external mouse and see if the problem persists.

  Then...

  If you use Microsoft Security Essentials, start here - https://support.microsoftsecurityessentials.com/ and select the link that says - I think my computer is infected. Options vary by region, but phone support leads you to the Microsoft answer service (http://www.answerdesk.com/) in the USA at this time. After an initial free consultation, will be charged a fee for assistance, based on the details of the case.

  If this is not the case, go to your provider AV.

  You can also try this web site - http://www.bleepingcomputer.com - contains details for most common infections, often immediately after that they started to appear in the wild, and instructions are provided for how to remove infections using their malware removal guides. They also have forums where you can seek assistance from people who specialize in the removal of malware.

  Here are other free programs that can help:

  Malwarebytes anti-malware free - http://www.malwarebytes.org/products/malwarebytes_free Please note, do not accept the trial version of MBAM Pro that it will conflict with MSE while the free version won't.

  SUPERAntiSpyware Free - http://www.superantispyware.com/downloadfile.html?productid=superantispywarefree

  TDSSKiller (free) - http://support.kaspersky.com/faq/?qid=208283363

  HitmanPro (free for 30 days) - http://www.surfright.nl/en/hitmanpro

• System Restore does not work, once again.

  Hi, I read a topic of 2010 that has not yet been answered. I worked with a tech at Microsoft by e-mail, but when I answered: System Restore didn't work. Now it does not work yet. I had installed Returnil system safe, but I got an error msg 0 x 80004005, (third-party antivirus), so I uninstalled the program. I went through the registry and delete something with Returnil all 4 sections of the registry. Remove the common files folder that was left after uninstalling. Restarted my computer several times. I use MSE, with free versions of spywareblaster and MBAB, who are both at the request not in real time. I tried to restore to a time before I had installed Returnil first, (I installed and uninstalled 3 times in 2 days) and could not. I tried to use a snapshot to restore spywareblaster and managed to restore to the point 2 x before installing because forward the installation of point returnil has been altered. At the moment no malware has been detected and no threat of MSE. What to do next?

  Thanks in advance for any help. Liz.

  Here's my usual route to find out how to reinstall System Restore:

  If you have already run MBAM and SAS, temporarily disabled your antivirus and anti-malware applications and tried your Safe Mode system restore and you still get the restoration of the system to work, you must reinstall just your system restore.  You do not have to reinstall XP - just reinstall the system restore part.

  System Restore is a frequent target of attacks by malicious software.

  When you reinstall the system restore, all your current Restore Points will be deleted and you must restart your computer once the installation is complete.  After the reboot, a new Restore Point will be created as a new point of system control in your calendar of SR.

  If your system had a malware infection, it could be that some of the files in your old Restore Points are also infected up to wipe out the 'old' and new is often a good idea if you wonder if the old Restore Points are infected or not.

  Assuming that your XP is installed on drive C of your computer:

  As you go through the reinstallation of the RS, the resettlement will be asked to locate certain files as you go along and ask your XP installation CD.   If you do not have a genuine XP bootable installation CD, you can change the path where Setup looks for files one at a time, because they are needed.  More on that later.

  Navigate to the following folder:

  c:\Windows\Inf

  Locate and right-click the following file:

  SR.inf

  Choose Install

  If you can not see the sr.inf file, set up your system to show hidden files and show file extensions.

  Click on tools, Options, view and turn on "Show the hidden files and folders" and uncheck "Hide extensions for known file types", then you should be able to see the file c:\windows\inf\sr.inf.

  Installation can request files from the c:\windows\inf\386 folder.  It would be your installation CD bootable XP genuine if you have one and the Service Pack installed on your system must be the same as the CD that you will use.

  You don't need absolutely a CD to do the reinstall, because files must already be on your system somewhere if SR was working before.

  If you are prompted for a file, and you can't find it where I suggest in my example below (it works on my system), you need to search your hard drive and find where the files on your system.

  If the request to a file and you don't know where he is, let waiting for installation and click Start, search, and search for it
  has requested the file and find it on your system.  If SR has already worked before, the file is already on your system somewhere.

  Search finds the requested file, go back to the installation and specify the path where you found the file requested and click OK.  Installation can request several files along the way, but you can find them all.

  Here's how my system works when I reinstall SR when I pretend that I don't have a genuine XP bootable installation CD:

  When you are asked:

  SR.sys

  Point the install in c:\windows\system32\drivers

  When you are asked:

  c:\windows\system32\srclient.dll

  Point install it in c:\windows\system32

  When you are asked:

  Filelist. XML

  Point of installation at c:\windows\system32\restore (or c:\windows\ServicePackFiles\i386)

  When you are asked:

  srframe. MMF

  Point installation c:\windows\system32\dllcache (c:\windows\system32\restore)

  Once installation is complete, you will receive a message that you must restart your computer.

  Restart your computer and look at your schedule of SR.  You should have a new point system control in your calendar.

  When you get SR working again, I ran MBAM and SAS to make sure that your system is reasonably clean of malware.

  The day that you think you need to help the system restore you is not the day to discover the system restore does not work, then you need to test.

  After the reinstallation, manually create a Restore Point and test the restoration process and make sure that you are convinced that it works from one end to the other.

• system files and command prompt does not work

  For the last two weeks, I'm having a nightmare. I disabled system restore and when I turned it on again every thing had stoped working (microsoft word and works procedssor), the user account micxrosoft help and support).

  I tried using command prompt, but it does not work properly. When I typed in the shadow of the list he has the right to copy, my name and disturbing without clichés present in this system.  When I go to system restore I just get ablank screen white. If I go into system the control panel says that my C drive is followed.

  I don't know what else to do Windows XP came with the perchase of my little computer. I only am not computer savvy very please check all instructions fool proof. Please HELP, as all I want for Christmas is saystem restoration. Thank you very much

  Please provide additional information on your system:
  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?
  It seems that your system has or has had a malware infection.

  What is the issue that you are experiencing that you think that the system restore will be remedied (or you are just convenient)?  System Restore is not a time machine...

  You should be able to get your system restore calendar works again quite easily, but who will not only relieve your system of malware.

  Don't forget to fix the problem and the difficulty not only the symptom of the problem.

  If you disabled the system restore and he turned his back, which removes all points existing restoration (this is how it is supposed to work).

  I run a few scans of such malicious software indicated below, then work on all the remaining issues.

  Sometimes malicious will afflict your system restore to prevent you to find and remove malware.  It would much rather you trick into thinking that you need to repair or reinstall your XP when it is not necessary.  System Restore is sometimes so afflicted, you need to reinstall the system restore (you don't have to reinstall XP - just reinstall the system restore).
  No matter what you use for protection against malware, I do so and then only begin to solve any problems:
  Download, install, update and do a full scan with these free malware detection programs can solve any problems:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  It can be uninstalled later if you wish.
  Restart your system and resolve outstanding issues.
  If your system restore calendar is always to show just a blank white screen, do the following:
  The scans using own it may also be necessary to re-register some dll (or you can do this part first, but you still have to do the scans).

  Re-record the dll is correct, even if they do not need re-registration.  You can also re-register the dll before the scans that can solve the problem, but the scans are always recommended.

  Click Start, run, and in the box enter orders following one at a time.  Click the OK button to execute each command one at a time:

  regsvr32 jscript

  regsvr32 vbscript

  regsvr32 /i mshtml

  The last order for mshtml load the DLL but can also contain a harmless warning depending on your environment.

  Check your system restore calendar now.

  Do, or do not. There is no test.

  Someone please tell me how to make figgy pudding like these kids keep saying they won't until they get some.

  I decided to implement the points for a new puppy instead of a pony!

• 0X803C0107 error: you cannot access shared files and printers and the MSE does not start at startup

  Original title: mainly MSE does not start at startup. have you tried re-loading and other elements on the card, still no luck. Here is the error code I have and the information complete.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • Error 0X803C0107

    Details of the editor for Windows Firewall troubleshooting

    Verified issues

    You cannot access shared files and PrintersYou cannot access shared files and printers

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445. Checked

    No workingRemote Assistance remote assistance does not

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance. Checked

    Windows Vista may not start Windows Vista FirewallWindows could not start the Windows Firewall

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned. Checked

    Windows Firewall service is not his firewall service is not started

    Windows Firewall service is not running or is not started. Checked

    Issues checked the details of the detection

    6 you cannot access shared files and printers checked

    You can't access shared folders or printers on a computer on which Windows Firewall is enabled. This happens when the Windows Firewall blocks traffic entering via the UDP ports 137 and 138 and the ports TCP 139 and 445.

    Unlock the file and printer sharing in Windows Firewall works not

    To allow access to shared folders and printers, except for the file sharing and printers in the Windows Firewall must be enabled.

    6 remote assistance works not verified

    When you use Windows Help and Support, remote support available to offer assistance to a computer, you receive the error message "the remote server computer does not exist or is unavailable", even if Remote Assistance and file sharing and printing are activated. Windows Firewall may be blocking Remote Assistance.

    Allow Remote Assistance in Windows not running Firewall

    Which allows Assistance remotely as an exception in Windows Firewall it unlocks and corrects this problem.

    6 Windows Vista could not start Windows Firewall check

    On a computer that is running Windows Vista, you find that the Windows Firewall service is not running. When you try to manually start the service, you get "Windows didn't start the Windows Firewall on the Local computer." For more information, see the system event log. If it is a non-Microsoft service, contact the service vendor and refer to service particular 5 error code. "error message. This can occur if the 'MpsSvc' account does not have the necessary permissions for the registry keys concerned.

    Set permissions for the registry keys concerned not run

    Setting permissions for the registry keys concerned will solve this problem. Applies only to computers by using Group Policy to manage the firewall.

  6 Windows Firewall service did not start Checked

  Windows Firewall service is not running or is not started.

  Start the Windows Firewall service is not running

  Start the Windows Firewall service solves this problem.

  Details of detection

  Collection information

  Computer name: NORMBRESINSKI

  Windows Version: 5.1

  Architecture: x 86

  Time: 09-20-2010 07:51:49

  Publisher details

  Troubleshooting Windows Firewall

  Automatically fix problems of Windows Firewall, such as Windows cannot start the firewall service (0x5) Windows or Windows remote assistance does not work

  Package Version: 1.0

  Publisher: Microsoft Corporation

  You have problems with programs

• Error messages
• Recent changes to your computer
• What you have already tried to solve the problem

Hi Rickbsk,

You can check out the link and check the suggestions provided by scotty1294.

http://social.answers.Microsoft.com/forums/en-us/msestart/thread/05a63b12-1be9-4BD3-898e-64674c1e9afd

If you have not tried all the suggestions above, try and see if it helps.

Hope this information is useful.

Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Defender of the window does not work.

  I recently had the Vista antispyware 2012 the virus.  I was able to get rid of it, but now the Defender window does not work.  When I click on the icon I get a pop up msg: "failed to initialize: 0 x 80070006.» The handle is invalid. "How to operate?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/why-does-my-Windows-Defender-not-work/a9c81020-cf8d-4149-8B4B-bc059ecf500a

  But you should also read this:

  http://answers.Microsoft.com/en-us/protect/Forum/protect_start/Windows-Defender-and-Microsoft-Security-Essentials/5309cb8d-02e1-40E8-974f-0dcedb9ab9fd

  Norton, AVG and McAfee, MSE will disable Windows Defender for dreaming of potential conflicts with their respective programs.

  I hope this helps...

• No list of programs and launch the search does not work.

  Last year a virus creeped into my system. After I couldnot find and delete I ran combofix that seems to help eliminate the virus. However, I have a lot of files and corrupted files in my system that I don't recognize. also, my search for the Start button does not work after this difficulty and "all programs" list has disappeared. I recently found that I have to do a system restore but my dates do not go too far before the virus. What should I do? I have a 32-bit windows vista system.

  Thank you.

  The best way to get rid of the shinannigans on your computer is to reload windows itself with the multimedia installation/installation partition if you have one. If this is not the case, I suggest to download and run Microsoft Security Essentials http://www.microsoft.com/security/pc-security/mse.aspx this is a free anti-virus MS. Try creating a new account on your computer and connection in there to see if your search bar and list of program starts working again:

  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account?SignedIn=1

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-a-users-account-type

  For these two make sure you click on my computer is on a workgroup for instructions and follow the steps in BOTH of the links

  If they then delete your old account and just use the new using Microsoft Security Essentials.

  I hope this helps!

• Windows Defender dialog box indicates it does not work.

  Problem with windows defender

  I use windows vista, my problem is with windows defender, it does not work well, even, it does not start when I click on icon (icon is correctly linked) displaying a dialog box to turn on the Defender, but that does not work.     After that restart Defender opens in a seprate window but after a few minutes (1-2 min) it turns off automatically

  Windows Defender cannot be used with AVG, McAfee, Microsoft Security Essentials (MSE) or Norton and several other similar programs.  It is part of the Vista and Win 7 operating system and cannot be uninstalled.  Maybe your antivirus program is disabled Windows Defender - and maybe it's exactly what it is supposed to do.

  You may want to consider the following: Windows Defender and Microsoft Security Essentials

  If you can not only your problem please post back and elaborate detailed about your computer, program antimalware, etc...

  Kind regards...

• Disk drive does not work / missing

  I am trying to restore my laptop to its factory settings, but my CD player does not work. The only time wherever it seems to work is when the laptop is turned on and then a few seconds later, when I logged on it not working + open to all. on my computer the CD drive does not appear. can anyone help?

  You can see the effects of an ongoing infection "hijackware. That being said, the result of your Validation check is more encouraging.

  NOTE: Must have uninstalled AVG before you have installed MSE, not later! See http://answers.microsoft.com/thread/bf757e6a-e320-4a67-92bc-767e6acb26c4 (and possibly http://answers.microsoft.com/thread/87058857-d181-4019-a723-efd9a49d9275).

  ~~~~~~~~~~~~~~~~

  [You can print these instructions for reference offline. [If a step said to restart, restart! ]

  ACTIONS:

  1. right click on the following link & SAVE the removal of AVG on your desktop tool: http://download.avg.com/filedir/util/support/avg_remover_stf_x86_2011_1322.exe

  1B. download the Norton removal tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. right click on the file that you saved in # 1 above and select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  3B. right-click on the file that you saved in # 1 b above and select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then reboot again.

  4. open Internet Explorer (only!) to http://support.microsoft.com/kb/923737 & run the difficulty.

  5 IMPORTANT - DON'T SKIP THIS STEP! Open Internet Explorer (only!) to http://support.microsoft.com/kb/971058 of => & run the difficulty in DEFAULT modes and AGGRESSIVE. [2]

  6. restart one last time & test the functionality of your CD/DVD drive but please don't "restores [your] laptop to factory settings it is ' immediately.

  Also run a manual check of updates by http://windows.microsoft.com/en-us/windows-vista/How-can-I-tell-if-my-computer-is-up-to-date

  7. make sure you can update MSE manually via the button UPDATE tab UPDATE by now. (Yes, even if you updated the definitions in #6 above).

  8. for reasons of security, then run a full scan of the system with MSE - do not TOUCH your computer until the scan ends. Let it run all night, if necessary.

  9. response to this post with a sometimes the outcome of the MSE analysis status report.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Comment: If push comes to shove, it is there is a hidden partition restore (not to be confused with the restoration of the system) you can use to do a clean install. Understand that if the hard drive does not work because of a hardware failure, a clean install will NOT repair.

  [Under the guidance of correct a few typos]

• Vista Search & indexing does not work

  When I go to Control Panel/Indexing Options/Advanced/show Options all the locations of some files are to check, but the OS(c:) est grisée.) I had turned off at the same time & now cannot get it turned back on.

  How to make this work?

  Why indexing taking so long?

  Why can't stop indexing or turn it off for awhile (it interferes with other programs sometimes)?

  Why seek complex with a bunch of drop downs and it usually does not even get just a subfolder. I searched (using the F command) 3 letters in a title only and got a response from an area not indexed that contains NONE of the letters, and it took several minutes. @!

  Some MS answers say to use the troubleshooting Index feature, but it doesn't seem to be indexing window.

  Hello

  These two showed more problems of search for Windows 7, however, they also seem to be
  able to affect Vista as well.

  
  1. one thing that seems to have an impact on several is the bit REACH has been set on some files
  Index cannot be set and search for cannot be found. So the ATTRIB-a *. * bps, which means archive
  is REMOVED for the files in the folder/directory Parent (top) and those in all the subfolders/sup-
  directories.

  Check out this link.
  http://mikekirby.spaces.live.com/blog/CNS! E008D856FA702CAC! 758.entry

  How to play and off the read-only file and folder attribute in Windows (see the second method)
  http://www.SevenForums.com/tutorials/63741-read-only-file-folder-attribute.html

  ------------

  2 another problem seems to be McAfee and some other antivirus programs are interfering with the
  Index or search functions. McAfee, must be uninstalled using the uninstall routine in
  Windows AND the removal of McAfee too of course no remains are left. (Possibly other antivirus
  programs are also what causes this error.) Of course, you want to move to another antivirus
  MSE (Microsoft Essentials), Avast or other.

  ===============================================
  ===============================================

  Windows Search does not work or research are slower
  http://support.Microsoft.com/GP/windows_search

  Troubleshooting Windows Vista search & indexing errors
  http://www.WinVistaClub.com/T24.html

  Reconstruction of the Index in Windows Vista
  http://www.howtogeek.com/HOWTO/Windows-Vista/rebuilding-the-search-index-in-Windows-Vista/
  How to enable or disable the search Index in Vista
  http://www.Vistax64.com/tutorials/69564-index-enable-disable.html
  Improve Windows searches using the index: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/improve-Windows-searches-using-the-index-frequently-asked-questions

  ================================

  Tips for finding files
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-finding-files

  How to use advanced search in Vista Options
  http://www.Vistax64.com/tutorials/75451-advanced-search.html

  How to restore the page button on the Start Menu after installing Vista SP1
  http://www.Vistax64.com/tutorials/145787-Search-start-menu-button-restore-after-SP1.html

  How to restore the context Menu item search after installing Vista SP1

  
  http://www.Vistax64.com/tutorials/134065-search-context-menu-item-restore-after-Vista-SP1.html

  How to create a shortcut on the desktop search in Vista
  http://www.Vistax64.com/tutorials/126499-search-desktop-shortcut.html

  ----------------------------------------------------------

  Win Key F opens advanced search

  Searching in Windows Vista, part 1
  http://Windows.Microsoft.com/en-us/Windows-Vista/searching-in-Windows-Vista-part-1-secrets-of-the-search-box

  Part 2
  http://Windows.Microsoft.com/en-us/Windows-Vista/searching-in-Windows-Vista-part-2-Start-menu-and-control-panel-search-tips

  Part 3
  http://Windows.Microsoft.com/en-us/Windows-Vista/searching-in-Windows-Vista-part-3-using-advanced-search-for-those-hard-to-find-files

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Windows 7 slow down and MS security essential does not work with error "0xc0000185.

  My PC does not work well.

  I use Windows 7.

  When I tried to open it, it will take at least 5 minutes before turning into log in page. and after I entered my password again 5 minutes to load.

  When I connect successfully my essential security MS does not work with error "0xc0000185"... then my Explorer windows always crashing.

  After each action I did it takes time to load... also, I tried to turn on my Defender, but unable to locate... I also tried to analyse using malware bytes, but it also shut down the application...

  Help, please. I need all my files...

  Thank you.

  Hello

  Windows Defender is disabled by default when you use MSE and nothing to worry about.

  Analysis of Malware in Mode safe mode with networking.

  Download, install, update and scan your system with version free Malwarebytes AntiMalware and if necessary do in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  'Advanced options boot (including safe mode).

  http://Windows.Microsoft.com/en-us/Windows/Advanced-startup-options-including-safe-mode#1TC=Windows-7

  _______________________________________

  And also scan with the free version of SUPERAntiSpyware

  http://www.SUPERAntiSpyware.com/download.html

  SUPERAntiSpyware Free Edition is 100% free and will detect and remove thousands of Spyware, Adware, Malware, Trojans, KeyLoggers, Dialers, Hi-Jackers, and worms. SUPERAntiSpyware features many unique and powerful technologies and removes spyware threats that other applications fail to remove.

  SUPERAntiSpyware Free Edition does not include blocking in real time or scheduled scan.

  ______________________________________

  It is a very good program to scan your system to remove adware, etc.:

  http://www.bleepingcomputer.com/download/adwcleaner/

  AdwCleaner is a program that finds and removes the Adware, toolbars, potentially unwanted programs (PUP) and browser hijackers from your computer.  Using AdwCleaner you can easily more of these types of programs for a better user experience on your computer delete and while browsing the web.

  _____________________________________

  And just to be sure, nothing is lurking in the background:

  'TDSSKiller Rootkit Removal Utility download for free'

  http://USA.Kaspersky.com/downloads/TDSSKiller

  See you soon.

• Safari does not work after installing macOS Sierra

  Safari and apple store does not work after installing macOS Sierra

  Alas, my crystal ball is in the shop for cleaning, so you will need to provide more details on what "doesn't work" and above all error messages. First of all, let's start the App Store. Provide as much information as possible for those of us who do not sit on your shoulder.

• My iPad Apple 3rd generation wifi + his cell phone does not work

  MY 3rd generation Apple iPad, wifi + cell

  model number MD408LL/a

  Serial number DM * VGL

  THE SOUND DOES NOT WORK

  < personal information under the direction of the host >

  All sounds, or simply notification and sounds apps (for example do music and videos app still have sound)? If notifications and apps you have notifications on mute: on the iPad side switch - Apple Support ? If the sounds in all applications which have tried for example soft-reset/reboot of the iPad, insert/remove the headphones?

• After recent, iPhone, 6, update, Windows, Explorer, does not work, see, iPhone

  I installed the latest update required for my iphone ios 6 a few days ago, and now when I try to download pictures from my iphone to my PC (via USB connection), the PC does not see the iphone.   iTunes sees it yet, but windows Explorer does not work.  It seems that some setting has been broken through the update of ios.  A way to solve this problem?

  Restart the computer and the iPhone. Unlock the iPhone before connecting it to the computer. Any change?

  TT2