Multi-router multi-homing with PfR
I am trying to set up a connection to edge where we are served by two Internet service providers, each connected to an independent router in our site (i.e. ISP-1 connects to R-1, and PSI-2 connects to R - 2). We eBGP peer tables full with each ISP and have active HSRP on the internal R-1 & R-2 interfaces. I want to configure PfR so that R-1 & R-2 is the border units and PfR creates a consumption semi balanced links to the ISP - 1 & PSI-2. Below is the configuration that I'm imagining.
What I am unsure of is how to get my firewall to take advantage of the PfR without having to extend the iBGP in the firewall (and I do not want to link the resources of the firewall with a table full of BGP to each of the ISP). Can I put the firewall with a next hop by default 192.206.43.1 (HSRP address) and let communicate with any router is active, and then this router can kick to the other edge router if the injection of LICs show a better way? Each of our uplinks running 100 M while the transfer area is 1 G; in my mind this means there will be plenty of room for routers to jump next to each other on the transfer area and still draw full ISP speed...
At the end of the day, I want just normal operations to use the two Internet service providers (doesn't have to be a balance perfect load 50-50, I don't want to pay for a link that is still inactive when I could use it to effectively double our available bandwidth). And for a failure of an ISP to handle passing all traffic through the ISP which is still in place.
Note: IP addresses and THAT the numbers have been changed. Although these good numbers, they do not represent my organization it.
To do this, here are the configurations that I look at.
R-1
! -- Key for PfR comms --key chain PfR_Router_1 key 1 key-string SecretSquirel343!! -- Setup as PfR border router --pfr border logging local GigabitEthernet0/0 master 192.206.43.5 key-chain PfR_Router_1!! -- Track the internet uplink for internal HSRP redirection --track 1 interface GigabitEthernet0/1 line-protocol!interface GigabitEthernet0/0 description Transfer Zone ip address 192.206.43.3 255.255.255.0 standby version 2 standby 1 ip 192.206.43.1 standby 1 preempt standby 1 name WAN-Transfer-v4 standby 1 track 1 decrement 20!interface GigabitEthernet0/1 description Uplink to ISP-1 bandwidth 100000 ip address 174.47.175.114 255.255.255.252 speed 100 full-duplex!router bgp 3457 bgp log-neighbor-changes ! -- advertise our nets -- network 192.206.42.0 mask 255.255.254.0 neighbor 174.47.175.113 remote-as 4323 ! -- dont redistribute anyone else -- neighbor 174.47.175.113 prefix-list Local-Site out ! -- iBGP with R-2 -- neighbor 192.206.43.4 remote-as 3457 neighbor 192.206.43.4 next-hop-self!! -- included as a parent route for PfR --ip route 0.0.0.0 0.0.0.0 174.47.175.113 name ISP-1ip route 192.206.42.0 255.255.255.0 192.206.43.2 name DMZ-Firewall!! -- only advertise us to the outside world --ip prefix-list Local-Site seq 10 permit 192.206.42.0/23
R-2
! -- Key for PfR comms --key chain PfR_Router_2 key 1 key-string MoroccoMole117!! -- Setup as PfR border router --pfr border logging local GigabitEthernet0/0 master 192.206.43.5 key-chain PfR_Router_2!! -- Track the internet uplink for internal HSRP redirection --track 1 interface GigabitEthernet0/1 line-protocol!interface GigabitEthernet0/0 description Transfer Zone ip address 192.206.43.4 255.255.255.0 standby version 2 standby 1 ip 192.206.43.1 standby 1 preempt standby 1 name WAN-Transfer-v4 standby 1 track 1 decrement 20!interface GigabitEthernet0/1 description Uplink to ISP-2 bandwidth 100000 ip address 38.122.32.166 255.255.255.252 duplex full speed 100!router bgp 3457 bgp log-neighbor-changes ! -- advertise our nets -- network 192.206.42.0 mask 255.255.254.0 neighbor 38.122.32.165 remote-as 174 ! -- dont redistribute anyone else -- neighbor 174.47.175.213 prefix-list Local-Site out ! -- iBGP with R-1 -- neighbor 192.206.43.3 remote-as 3457 neighbor 192.206.43.3 next-hop-self!! -- included as a parent route for PfR --ip route 0.0.0.0 0.0.0.0 38.122.32.165 name ISP-2ip route 192.206.42.0 255.255.255.0 192.206.43.2 name DMZ-Firewall!! -- only advertise us to the outside world --ip prefix-list Local-Site seq 10 permit 192.206.42.0/23
R MC
! -- Key for PfR comms --key chain PfR_Router_1 key 1 key-string SecretSquirel343key chain PfR_Router_2 key 1 key-string MoroccoMole117! ! -- Setup the PfR Master Controller --pfr master logging! border 192.206.43.3 key-chain PfR_Router_1 interface GigabitEthernet0/1 external interface GigabitEthernet0/0 internal! border 192.206.43.4 key-chain PfR_Router_2 interface GigabitEthernet0/1 external interface GigabitEthernet0/0 internal!interface GigabitEthernet0/0 description Transfer Zone ip address 192.206.43.5 255.255.255.0
Hello
I have not implemented PFR in a network of practice so I answer your question since no one else did.
If you don't need a very high level of load sharing, there are other easy ways to achieve this. PFR needs a lot of tuning; However, your configuration shows only the default settings. (you must enable learning about master also).
As for ASA, ASA does not support the PFR, so you have to find another way to use the link between the ASA and your border routers. Border routers will manage the load sharing your ISP based on your topology.
Only a suggestion. Add an additional link between your border routers to connect IBGP to avoid receiving the traffic by your ASA l2. Because ASA sends traffic to the edge router for example 1 and edge router 1 can send router 2 via the same link limit, she received traffic.
Please see the link below for more information tuning.
https://aitaseller.WordPress.com/2012/10/15/PFR-Cisco-performance-routing/
much more simple method in load sharing can be made preferably local BGP, if you find the PFR difficult to implement.
It will be useful,
Masoud
Tags: Cisco Network
Similar Questions
-
can you multi delete with out checking all of the boxes.
Can u multi delete with out checking all of the boxes.
This is for email, but it is almost global.To remove all the: select one and Ctrl + A will highlight all. -Delete.To delete a section: highlight the first one you want to remove. Scroll to last and click while holding down the SHIFT key. -Delete.To delete several messages that alternate: hold down the CTRL key while you click each message in order to highlight. -Delete. -
Hi all
I recently recorded a production of theatre and because of some limitations of record on some camera, I've seen camera that is non-stop, and three others who cut inside and out for the big musical numbers or great moments, etc. Is it possible to create a view of multi-camera with multiple views, I, because none of them share a common point of synchronization? Is it possible to set multiple synchronization points and label all so that they can synchronize correctly? I'm sorry if it's very confusing! Thank you very much.
Kyle
multicamera Create Sequence of Source, with Sync Point, choose Audio
-
Convert application folio multi multi-folio with iTunes subscription
Hi all
You can convert a multi-folio (non-kiosque) multi-folio with iTunes subscription application? i.e. If you have built an application and you have in the app store, could replace you it with a new kiosk of targeting build?
Thank you
Toby
I think, but once you went on newsstands you can not update the application to quit Kiosk if I remember correctly.
Neil
-
have a multi-record with several unrelated elements blocking, filled by simply calling
Forms of oracle, I have a form with a block of several recording, with several unrelated elements.
One of these non-is a basic formula element.
The formula for this article fills the others not consolidated items.
A procedure with several out parameters is called.
For example
: cmr.id (now the unique id of a database record)
: cmr.unbound_dummy, with the formula f_fill_blk_unbound_items(:blk.id)
: cmr.unbound_adres
: cmr.unbound_contactperson
function f_fill_blk_unbound_items (p_id in customers.id%type)
Return number
is
number of l_rc;
Start
customer_pck.get_adres_and_contactperson
(p_id = > p_id - IN)
, p_adres = >: cmr.unbound_adres - OUT
, p_contactperson = >: cmr.unbound_contactperson - OUT
);
Return (0);
end;
QUESTION: How can I do something similar in the APEX; have a blocking of multi-record with several elements not related, filled by calling a procedure with several out parameters?The suggestion refers to functions in pipeline
http://www.Oracle-Developer.NET/display.php?ID=207This will allow you to select your information you need in a query like
SELECT * FROM TABLE(table_function)
It should also more powerful than the example of forms.
Scott
-
I got a modem Comcast/Xfinity upgrade. Xfinity X 1 modem/router is compatible with the Airport Extreme? How it should be configured to maintain my wireless network?
Whenever you change the modem or modem/router on a network, AirPort Extreme will be reset to the default settings and then set it up again to work properly with the new modem. For this he would be...
Turn on AirPort Extreme for a few minutes... If it is not already turned on
Hold in the reset button on the back of the AirPort Extreme for 7-8 seconds, then release it.
Allow a minute for the AirPort Extreme restart to a slow, flashing amber light status
Make sure that an Ethernet cable connects to one of the four LAN <-->Ethernet ports on the modem/router on port WAN "O" on AirPort Extreme
To start the Setup program, click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station
Just below that, click directly on the AirPort Extreme and then follow the prompts for configuration "Wizard".
When you configure AirPort Extreme once again, you can use the same wireless network name and the same password that you used with AirPort Extreme with the 'old' modem, if you wish, or use a new wireless network name and password
--> -
E2500 router communicates only with HP printer cable.
I have a HP color LaserJet 2605dn printer and router e2500. I decided to run an Ethernet cable from the router to the printer instead of via the USB port of the laptop that works fine for a couple of years.
Is the green light on the router would be flashing quick or light yellow on the printer. Guess there is a communication problem. After some reading material at random on Web sites and messages, I manually changed the IP address of the printer: 192.168.1.110 (that is outside the range of the DHCP users (6) quantity, which starts at 192.168.1.100)
Leave the configuration window Panel > devices Printers & I added a new "Standard TCP/IP Port" to match the one I put manually (192.168.1.110).
I varied results when I ping this new IP address while that the yellow light on the Ethernet port on the printer flashes quickly. Sometimes I will have 4 packets that have been sent in the ping also received, sometimes none are received, sometimes 1 and sometimes 2 packets are received. For example, ping results are contradictory and I don't know why that should be.
I guess that none of my configurations 'Basic Wireless Settings' and "Wireless Security" have an impact here. After all, I'm trying only to communicate with my printer wirelessly via my laptop to the printer via a network cable. Also, I'm not a very technical person. I managed to get this far, but I'm at a loss for what keeps my router to communicate with the printer of mine. Any help would be appreciated. Thank you.
Using the printer management page, make sure you on the JetDirect Automatic for networking information. If your automatic support of networking, it must acquire an IP address from the router if the LAN cable is in good working condition. Make a print on the printer configuration page to see what IP address it acquired from the router.
If you decide you want to put a static IP address on the printer, make sure you on the JetDirect information
Manual and instead use 192.168.1.110 tends in the poole DHCP address, try using 192.168.1.26. You will need configure the printer driver in windows accordingly to point to the IP address. -
Cisco router restarts randomly with Bus error
Cisco router restarts randomly with the following error:
System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013
I've pasted below see the chimneys and release the version.
view the stacks
Minimum factory chimneys:
Format name / free
5396/6000 inspect Init Msg
Subsystem SPAN 5368/6000
58920/60000 EEM Auto record Proc
Automatic start of 4772/6000 upgrade process
DIB 5164/6000 error message
HAND OF SASL 5396/6000
4968/6000 LICENSE DEFAULT AGENT
5368/12000 Init
4216/6000 update prst
4384/6000 VPN_HW_MIB_CREATION
5188/6000 RADIUS INITCONFIG
Update process random rom 2128/3000
8356/12000 SSH process
Stats URPF 5316/6000
Interruption of battery level:
Level named format / unused
Network interfaces 1 1484828 6284/9000
2 3264990 8548/9000 DMA/Timer Interrupt
3 1 8388/9000 PA Int management Manager
Console 4 115 8612/9000 Uart
External interrupt 5 0 9000/9000
NMI 7 223352 8564/9000 interrupt handler
Spurious interrupts: 11
System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013
Software of 2800 (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)
Technical support: http://www.cisco.com/techsupport
Updated Thursday 25 February 09 17:55 by prod_rel_team
Image text-base: 0 x 40011240, database: 0x42B41940
The failure of the system stack trace:
FP: 0X472252B8, RA: 0X4183614C
FP: 0 X 47225310, RA: 0X418312F8
FP: 0 X 47225348, RA: 0X41647DC0
FP: 0X472253A8, RA: 0X4164A8F4
FP: 0 X 47225428, RA: 0X4164B248
See the version
Cisco IOS software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Updated Thursday 25 February 09 17:55 by prod_rel_team
ROM: System Bootstrap, Version 12.4 (1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
availability of Cisco is 28 minutes
System returned to ROM by bus to the 0x4183614C PC error, address 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013
System image file is "flash: c2800nm-advsecurityk9 - mz.124 - 24.T.bin".
This product contains cryptographic features and is under the United States
States and local laws governing the import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third party approval to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. laws and local countries. By using this product you
agree to comply with the regulations and laws in force. If you are unable
to satisfy the United States and local laws, return the product.
A summary of U.S. laws governing Cisco cryptographic products to:
http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html
If you need assistance please contact us by mail at
Cisco 2821 (revision 53.51) with 1036288K / 12288K bytes of memory.
Card processor ID FCZ1017732F
2 gigabit Ethernet interfaces
2 modules of virtual private network (VPN)
Configuration of DRAM is wide with parity 64-bit capable.
239K bytes of non-volatile configuration memory.
250880K bytes of ATA CompactFlash (read/write)
Configuration register is 0 x 2102
You want to use the tool interpreter of output for this work:
http://www.Cisco.com/pcgi-bin/support/OutputInterpreter/home.p
For more information about the resolution of crashes, see this article:
http://www.Cisco.com/en/us/products/HW/IAD/ps397/products_tech_note09186a00800b4447.shtml
In this case, it looks like CSCsy09250, described here:
http://www.Cisco.com/en/us/products/CSA/Cisco-SA-20100324-SCCP.html
You should contact Cisco for the software updated by following the instructions of this bulletin.
That crash possibly caused by part of sone intentionally sends out packets malformed to your device, so if you have reason to believe that someone in your community could run metasploit or similar "Penetration Testing" tools, you can look into that as well.
-
router in 1921 with the double nat ADSL problem
I have problems with the implementation of a router in 1921 with double lines ADSL for failover. For some reason any internet traffic keeps using Dialer 1 as internet main connection, while 2 Dialer should be primary. Also, when I finish my NAT with allowed a full acl, it translates the public ip address of the 2-to-1 Dialer the Dialer before she sends in the internet.
This is my config:
!
interface GigabitEthernet0/0
Voice netwerk description
IP 192.168.77.254 255.255.255.0
IP helper 192.168.177.1
IP helper 192.168.177.254
IP nat inside
IP virtual-reassembly in
IP tcp adjust-mss 1400
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
Inside the interface description
IP 192.168.177.254 255.255.255.0
IP mtu 1492
IP nat inside
IP virtual-reassembly in
IP tcp adjust-mss 1400
automatic duplex
automatic speed
!
ATM0/0/0 interface
Description 1/10 Mb Tele2 ADSL
no ip address
No atm ilmi-keepalive
PVC 0/35
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface Ethernet0/0/0
no ip address
Shutdown
!
ATM0/1/0 interface
no ip address
No atm ilmi-keepalive
!
interface Ethernet0/1/0
VDSL 5/50 Mb KPN description
no ip address
!
interface Ethernet0/1/0.6
KPN VDSL description
encapsulation dot1Q 6
PPPoE enable global group
PPPoE-client dial-pool-number 2
service-policy output parent policy
!
interface Dialer1
Tele2 ADSL description
the negotiated IP address
no ip redirection
no ip unreachable
no ip proxy-arp
IP mtu 1492
NAT outside IP
IP virtual-reassembly in
encapsulation ppp
IP tcp adjust-mss 1400
Dialer pool 1
Authentication callin PPP chap Protocol
PPP pap sent-username *.
No cdp enable
card crypto SAL_map
!
interface Dialer2
VDSL KPN description
the negotiated IP address
no ip redirection
no ip unreachable
no ip proxy-arp
IP mtu 1492
NAT outside IP
IP virtual-reassembly in
encapsulation ppp
IP tcp adjust-mss 1400
load-interval 30
Dialer pool 2
PPP authentication pap callin
PPP pap sent-username *.
No cdp enable
card crypto SAL_map_VDSL!
IP nat inside source overload map route sheep interface Dialer1
IP nat inside source overload map route nonat2 interface Dialer2
IP route 0.0.0.0 0.0.0.0 Dialer2 Track1
IP route 0.0.0.0 0.0.0.0 Dialer1 254
!auto discovering IP sla
ALS IP 10
echo ICMP - 62.69.174.75 source-interface Dialer2
Timeout 30000
frequency 30
Annex IP SLA 10 life never start-time now
!access-list 102 deny ip 192.168.177.0 0.0.0.255 host 192.168.1.249
access-list 102 deny ip 192.168.178.0 0.0.0.255 host 192.168.1.249
access-list 102 deny ip 192.168.179.0 0.0.0.255 host 192.168.1.249
access-list 102 deny ip 192.168.177.0 0.0.0.255 172.28.1.0 0.0.0.255
access-list 102 deny ip any 192.168.255.0 0.0.0.255
access-list 102 deny ip any 192.168.254.0 0.0.0.255
access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.179.0 0.0.0.255
access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.178.0 0.0.0.255
access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.79.0 0.0.0.255
access-list 102 deny ip 192.168.177.0 0.0.0.255 192.168.78.0 0.0.0.255
access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.179.0 0.0.0.255
access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.178.0 0.0.0.255
access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.79.0 0.0.0.255
access-list 102 deny ip 192.168.77.0 0.0.0.255 192.168.78.0 0.0.0.255
access-list 102 permit ip 192.168.177.0 0.0.0.255 any
access-list 102 permit ip 192.168.77.0 0.0.0.255 any
!Dialer-list 1 ip protocol allow
Dialer-list 2 ip protocol allow
!
nonat2 allowed 10 route map
corresponds to the IP 102
Set the interface Dialer2
!
sheep allowed 10 route map
corresponds to the IP 102
Set the interface Dialer1the ACL is built to exclude some ips private for ipsec VPN destinations.
Any suggestions on what I'm missing? It must use dialer 2 as primary internet connection and failover of Dialer 1 if IP SLA fails. The SLA config seems to work properly:
SH ip route
S * 0.0.0.0/0 is directly connected, Dialer2
84.0.0.0/32 is divided into subnets, subnets 1
C 84.246.25.231 is directly connected, Dialer1
145.131.0.0/32 is divided into subnets, subnets 1
C 145.131.131.112 is directly connected, Dialer2
192.168.77.0/24 is variably divided into subnets, 2 subnets, 2 masks
C 192.168.77.0/24 is directly connected, GigabitEthernet0/0
The 192.168.77.254/32 is directly connected, GigabitEthernet0/0
192.168.177.0/24 is variably divided into subnets, 2 subnets, 2 masks
C 192.168.177.0/24 is directly connected, GigabitEthernet0/1
The 192.168.177.254/32 is directly connected, GigabitEthernet0/1
192.168.254.0/24 is variably divided into subnets, 2 subnets, 2 masks
S 192.168.254.0/24 is directly connected, Dialer2
192.168.254.37/32 S [1/0] via 77.241.229.241
S 192.168.255.0/24 is directly connected, Dialer1
212.121.121.0/32 is divided into subnets, subnets 1
C 212.121.121.183 is directly connected, Dialer2
213.144.228.0/32 is divided into subnets, subnets 1
C 213.144.228.72 is directly connected, Dialer1http://docwiki.Cisco.com/wiki/category:NAT
Above document indicates "Beware of the use of the ACL for the NAT with" ip allow a whole ' you can get unpredictable results. " I suggest using the "road-map sheep/nonat2 permit 20" instead of "allow a whole."
For others, change the config as follows-
!
ALS IP 10
Dialer2 interface source ICMP echo 8.8.8.8
Timeout 30000
frequency 30
Annex IP SLA 10 life never start-time now!
IP route 8.8.8.8 255.255.255.255 permanent dialer2
!
!
nonat2 allowed 10 route map
corresponds to the IP 102
match interface Dialer2
!
sheep allowed 10 route map
corresponds to the IP 102
match interface Dialer1!
IP nat inside source overload map route sheep interface Dialer1
IP nat inside source overload map route nonat2 interface Dialer2!
NAT-TRACK event manager applet
track event 1 show all
order cli action 0.1 'enable '.
action 0.2 wait 2
action command 0.3 cli "clear ip nat translations forced."
action 0.4 syslog msg "Translation NAT cleared after state change of track"
!
-Ginette
-
Need to know if my router is compatible with windows 7
The microsoft Web site seems to send me in circles and it drives me crazy! What I want to know is if my wireless method NB9W router is compatible with windows 7 or not...
It is a work laptop and our COMPUTER technician has not set. I can connect to the network wirelessly at work, but not my own wireless network at home. I read that some 'old' routers are not compatible with windows 7.
I can't find any info on my model of router on the microsoft Web site. Help please!
Hello
Collate support method because it might be and need the firmware, for example.
Using WPA or WPA2 (and not WEP) security? The value WPA or WPA2.
NB9W
http://www.netcomm.com.au/Netcomm-products/VoIP/nb9w?SQ_PAINT_LAYOUT_NAME=supportThis implies that it is Windows 7 compatible (might still need the firmware)
Windows 7 - obtain an IP address
http://www.YouTube.com/watch?v=XC7Ebm0UKi8and
Windows 7 - wireless connection
http://www.YouTube.com/watch?v=MqWJ7exMJhENB9W
http://www.netcomm.com.au/Netcomm-products/VoIP/nb9wMethod Support
http://www.netcomm.com.au/supportIt can be configured to not work on networks other than at work, have your tried on
other networks in addition to work and home?I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Multi camera with DSC-HX400V?
Hi, someone at - he tried the device with the Sony HX400V multi function or is not possible to agree with the two devices?
No problem. It was my fault because I did not try all angles, I had to touch the Z3 at the HX400 exactly. So I thought that there a little spinning remote because the camcorder connects if I hold the Z3 just near the NFC tag. -.
-
Deactivation of gestures on Windows 8, resizing specifically Multi screen with 2 fingers
Is there a way to disable a gesture several advanced in Windows 8? Specifically, I'm trying to disable or reduce the sensitivity of the screen resizing gesture. My son has small hands, and even when it is just by pointing the touchscreen picks up his other fingers like a multi-gesture and the size of screen shots in all directions.
He likes using ABCMouse.Com and Windows 8 with touch brings a new level of interaction of this educational site, but its basically useless resizing issue.
Thanks for the tips.
Try going to control panel > mouse > device settings > settings.
Simply, it worked for me. Hope this helps you -
See 4.5 true multi-monitor with RDP7?
I read this in the guide of the administrator on the page 17: ' Microsoft RDP provides the following features: you can use more than one monitor in span mode '
and this page 21:
In a real session of multiple monitors, monitors can have sizes and different resolutions, and a monitor can be
has rotated. If you enlarge within an application window, the window expands to the full-screen only the monitor
that contains it.
This feature has the following limitations:
n the maximum number of monitors that lets you view a desktop is 10 If you are using the RDP Protocol
view the Protocol and 4 If you are using PCoIP.
n If you are using the Microsoft RDP display protocol, you must have Microsoft Remote Desktop Connection (RDC)
version 6.0 or later installed in the desktop view.
I'm not completely sure if I read this right, but it seems that true multimonitor is NOT available with RDP. Even if Windows 7 and the last DRC have no problem with that at all. Can someone confirm (or reject if all goes well) that this is the case. I really prefer to use RDP, but I need the true multi-monitor.
Kind regards
Poort443
You need on the client, you connect from version 7. Version 7 comes with Windows 7 and Server 2008 R2. You can download version 7 for XP and Vista.
I wish version Mac was up to 7 and I wish THAT WYSE would improve their RDP to 7.
-
I read that PCoIP supports up to four monitors. It also works with RDP? I intend to use Windows 7 and RDP7 stand. I don't mean the duration of feature, but the 'real' multi taken in charge of monitoring. Thank you.
Good RDP 7 supports multimon. With some limitations however still. Such as AERO. You will need a RDP7 to Win7 backend as you described. View currently does not support RDP7, so you will not be able to operate but in the future when possible.
WP
-
M401dw multi-homed Laserjet Pro 400
This unit has two NICs installed, wired, one wireless.
Is it possible to set up on two separate subnets? And if so, to have two separate security for the web management interface configurations, such as activated a network card disabled on the other.
Scenario:
This device will be used (I hope) both internal (NIC1) and guest (WiFi) networks for occasional printing of conference rooms.
There is no communication cross between networks as they are completely separated which makes a network routing print jobs to another is impossible.
Printing environment:
Local: Printing Services Windows Server 2008, for Windows only on x 64 / x 86
Comments: IPP for Windows 2003 print server for Windows/Mac, Airprint for iOS devices
Thanks in advance.
Hello
I'm afraid this is not possible.
The printer can eitehr use wired ethernet or wireless connection to an Ethernet card disables the use wireless and the unit cannot be connected to two different networks at the same time...
You can connect with an ethernet card and activate the direct wireless feature which must not come into conflict with each other as far as I'm aware (at least he can work together for the consumption patterns), so you can connect a device to the wireless network without direct and impression is the narrower scenario, I see...
Direct wireless can be enabled in the network setup > wireless settings live.
Hope that helps,
Shlomi
Maybe you are looking for
-
Please make an extension that forces #YouTube to display the menu of the left sidebar even when play videos.
-
How can I reset Firefox to display relevant responses to my place?
Firefox shows the position relative to a place that I was in Sydney, NSW. I want to reset the answewrs to those near Torquay, Victoria.
-
How can I transfer my bookmarks from IE to Foxfire
I have a long list of favorites on my Internet Explorer screen. How can I transfer this list intact on my Foxfire screen? I don't know which toolbar are my favorites, because it is not marked anything other than bookmarks. Could be Windows, Internet
-
Can I use the SIM on a 4s in a unlocked 6s more?
Can I use the SIM on a 4s in a unlocked 6s more?
-
D2 Hard Drive Extreme maintenance?
Recently, I got intermittent connection on my external drive problems. http://www.LaCie.com/support/desktop-storage/D2-extreme-triple/ Should I do any function of regular maintenance to keep it in good working order? I tried to run the disk first a