Multiple SSID for AP in light mode

Similar Questions

• BVI Interface inaccessible since the addition of multiple SSID

  Announcement to the community for the first time.

  I have a simple HomeLAN which consists of a Cisco router for series 800-> switch PoE Cisco3560-> Cisco Aironet 1131AG Access Point.

  Everything works well for a while in which I had a simple port to "change the access mode" configured on the switch facing the AP and one SSID on the access point that is configured in stand-alone mode (without controller).

  My provider has enabled IPv6 on my broadband connection and I started to reconfigure my installation this afternoon to allow this.

  I decided to run only a bunk Dual LAN and a separate native IPv6 only test LAN for proof of concept.

  With this in mind, I changed the switch port to the access point to a "mode trunk switch' using simple dot1q encapsulation. I have also consulted the post helps very https://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on... after finding in this community post on the topic of multiple SSID https://supportforums.cisco.com/discussion/10899511/how-broadcast-2-ssid...

  I have now two SSID broadcasting (we will call double stack and ipv6 only for the sake of the argument). The SSID double stack uses VLAN 2 and 1 bridge, while the SSID only ipv6 uses 6 VLAN and bridge 6.

  I must stress at this point that my router (where I want to layer 3 for the two LANs gateways) I have DHCP, DHCPv6 and SLAAC configured on relevant VLANs.

  I seem to be the 2 VLAN trunking of properly and I can see the SSID broadcast in my house. I can connect to the SSID (authenticate and form an association as seen in 'show the dot11 association'), but I don't get an IPv4 address or IPv6 assigned to all clients (I tried Mac OS x, iOS, Android, and Windows phone). Furthermore, I can't ping the IP bvi1 of the AP - that is the element that is annoying me more that I must console to the AP to make any changes at all.

  Here is an overview of my AP configuration, with relevant parts removed for safety...

  dot11 syslog
  !
  dot11 said ipv6 only
  VLAN 6
  open authentication
  shared authentication
  authentication wpa key management
  MBSSID-guest mode
  WPA - psk ascii 7
  !
  dot11 said double stack
  VLAN 2
  open authentication
  shared authentication
  authentication wpa key management
  MBSSID-guest mode
  WPA - psk ascii 7

  interface Dot11Radio0
  no ip address
  no ip route cache
  !
  the cipher mode vlan 6 encryption tkip aes - ccm
  !
  the ciphers of vlan 2 encryption tkip aes - ccm mode
  !
  has declared ipv6 only
  !
  such double stack
  !
  MBSSID
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface Dot11Radio0.2
  encapsulation dot1Q 2
  no ip route cache
  Bridge-Group 2
  the bridge-group subscriber-loop-control 2
  Bridge-Group 2 block-unknown-source
  No source of bridge-Group 2-learning
  No extinction unicast by bridge-Group 2
  Bridge-Group 2 covering-disabled people
  !
  interface Dot11Radio0.6
  encapsulation dot1Q 6
  no ip route cache
  Bridge-Group 6
  the bridge-group subscriber-loop-control 6
  Bridge-Group 6 block-unknown-source
  No source of bridge-Group 6-learning
  No bridge Group 6 unicast-flooding
  Bridge-Group 6 covering-disabled people
  !

  interface FastEthernet0
  no ip address
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0.2
  encapsulation dot1Q 2
  no ip route cache
  Bridge-Group 2
  No source of bridge-Group 2-learning
  Bridge-Group 2 covering-disabled people
  !
  interface FastEthernet0.6
  encapsulation dot1Q 6
  no ip route cache
  Bridge-Group 6
  No source of bridge-Group 6-learning
  Bridge-Group 6 covering-disabled people

  Bridge IRB

  1 channel ip bridge

  interface control2
  MGMT AP Interface Description
  address 192.168.1.6 IP 255.255.255.0
  no ip route cache

  IP default-gateway 192.168.1.50

  As you can see I can not ping the gateway of AP - I would be very grateful if someone could point me in the right direction with regard to what I'm doing wrong here?

  Thank you

  Mick

  OK means your AP is to have IP vlan2:

  Do it like this and try again:

  !

  interface Dot11Radio0.2
  encapsulation dot1Q 2
  encapsulation dot1Q 2 native
  Group 1 bridge
  Bridge-Group 2
  !
  interface FastEthernet0.2
  encapsulation dot1Q 2
  Group 1 bridge
  encapsulation dot1Q 2 native
  Bridge-Group 2

  !

  Or alternatively, you can delete the name native dot11radio0 and fa0.2. (It should also work without it), but be sure that for vlan 2 you have bridge Group 1.

  Concerning

  Remember messages useful rates

• Addition of second SSID for public internet

  Excuse me, but I'm very new to this. We have 1230 APs that dates back to our 3550 s for our wireless company. We now want to add public wireless throughout the facility for our customers. We are keen to bring in a separate line of the T1 for public radio. I understand that the years 1230 can have multiple SSID. What other equipment do we need to complete it. If we need to add another switch for the audience, is not a problem, but how to divide the flow of the AP.

  Hello

  You can do this by using VIRTUAL networks and then assign the SSID. While you do the vlan different on the wired LAN, make the trunk links to the 1230AP and then also configure it vlan on the AP then you assign to different SSIDS. So simple :-). Just be careful that the VLAN (Group of deck 1) administration of the AP is the VLAN native, cause the AP do not support the beeing VLAN management one labeled.

  Simon

• Unique SSID from the multiple SSID

  Hello

  We seek to deploy wireless at five sites great campuses, one in each State.

  Does anyone have any ideas on the deployment unique verus multiple SSID SSID for each location.

  Are the benefits of filing a return and security to identify red devices associated with

  a unique SSID.

  The question was raised that it would be easier to configure one SSID to scan wireless

  devices that have separate SSID different places.

  Would appreciate any experience on this design

  Mate,

  Remember, when you're dealing with WLC, you do not configure the APs.  You configure the WLC and configs will be propatated of all APs manages the WLC.

  The WLC, you can use up to 18 SSID but you can configure 1 024.

  Currently, I have three SSIDS and one of them is for VoWLAN.

  Moreover, some hand scanners do not like the (hidden) SSID broadcasting.

• 1142 standalone image upgrade in light Mode

  Hi all

  I spend 1142 APs stand-alone a lightwheight with WCS, but I can't find the recovery image (c1140-rcvk9xxxxx).

  On the Cisco website > support > download > wireless > ap > 1140, if I click on the standalone link to light Mode upgrade Image, I get an error message "no final version available for downloads.

  Any ideas where to download this file?

  Thank you.

  Manu

  Hello Manu,

  Look under the standard IOS images for a - JA 12.4.21;

  WIRELESS LAN LWAPP RECOVERY                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                     c1140-rcvk9w8-tar.124-21a.JA.tar

  He's here for a reason

  See you soon!

  Rob

• Disseminate the Multiple SSID

  Hello

  I have an AP 1252 and I wanted to know what I need to do to set up to broadcast multiple SSID

  y at - it something I need to do on the web interface or something through CLI. Thanks in advance

  and have a great day.

  Please copy - paste the 'controllers to see the output. This will let us know if we can or we cannot broadcast multiple SSID.

  The command to enable this featute is...

  AP (config) #int dot11 0

  AP(Config-if) #mbssid

  SSID #dot11 AP (config)

  AP (ssid-config) #no - guest mode

  AP (config-ssid) #mbssid - guest mode

  SSID #dot11 AP (config)

  AP (ssid-config) #no - guest mode

  AP (config-ssid) #mbssid - guest mode

  This will do

  Concerning

  Surendra

• Docking station remains in light mode when you go dark

  When you turn on the dark mode, the bar menu goes into mode dark but the dock remains in light mode, even if the app under the icons indicators go to dark mode. I tried to restart my mac and relaunch the dock but nothing doesn't seem to help. I've attached a screenshot of the problem. Anyone know how to solve?

  

  Hi, appleuser493.

  Please visit Apple support communities.

  I understand the dock with do not adjust in the dark when option selected.  To avoid to go directly into a relocation, we will test to see if the behavior persists in a new user and also in safe mode.

  How to test a question in another account on your Mac.

  OS X El Capitan: start in safe mode

  See you soon

• How to show the multiple declaration for an application

  How to show the multiple declaration for an application

  Thanks for your suggestions...

  Looking at the javadocs you can only save an indicator by application. You will need to do three separate applications and package them as an If you want three different indicators to be visible at a time. Or change the flag that (or which group) of the indicators you want to display.

• XP drivers for Virtual PC - beta mode XP de Windows 7 RC necessary?

  Is it necessary to install drivers XP for Virtual PC - beta mode XP de Windows 7 RC? Or is it enough to install the drivers for Windows 7 RC only? Also, can I connect to the internet using the XP mode beta as I can simultaneously access Internet beta mode Windows 7 RC and XP?

  Basically, it will work like that.

  When you download Virtual PC (XP mode), you will need to install the current Windows XP in Virtual PC as if it were another computer. As if you were running the program under Windows 7, XP mode will give you 'seemless' support. (in reality, Virtual PC will run it), but don't look or act like him. So, as you install Windows XP, you need to install the Windows XP drivers in Windows XP.

  I hope that answers your question.

• How to submit multiple releases for a single application

  
  

  "I just continue to add beams.

  Yes pretty much.  I think it's better terminology, that you submit multiple beams for the 'liberation '.  Beams can be targeted by device and/or the OS level, so it's easy to create a version keyboard and touch screen using non-automatique operation weighing - although I'm not sure whose side the torch fits in!

• Can I assign some SSID for some specific points in the mesh network?

  Hi all

  We put a mesh in the site network. But a wireless client operate only at specific areas and that they are not on the move. So, I want to limit this ssid only at this place. So I wonder if I can attribute this ssid for 1 or 2 access points in this region. Other access points do not have this configured ssid. I can do this in WLC?

  Thank you very much!

  Lou

  He called the AP groups.  (Wireless > advanced > groups AP)

  Please do not forget to messages useful rate.  Thank you.

• About WLC "one-to-many" designates a LAN VIRTUAL mapped to multiple SSID possible?

  The Cisco Wireless LAN Controller Architecture includes this feature (possibility of configuration)?

  You can map multiple SSID to a VLAN, but you cannot map several VLANS on a SSID.

• Multiple SSID on AIR-SAP702I-E-K9 (700 Aironet Access Point)?

  Hello community

  I wonder if it is possible to simultaneously run multiple SSID (actually 3) on a single Cisco AIR-SAP702I-E-K9, which is a standalone AccessPoint (AP). Each SSID should be linked to a different VIRTUAL LAN. Or do I need another model or even an AccessPoint driven by the controller to run multiple SSID on different VLANS to the same AP?

  Thanks in advance.

  Kind regards
  Adrian

  Hi Adrien,.

  Yes, you can have multiple ssid on the AP standalone. Each SSID must be mapped to a VLAN different.

  Kind regards

  Shubham

  Please do not forget to note positions that answered your question and mark as answer or was useful

• WLAN client multiple ssid display & selection

  assuming that the two SSID on both radios, such as

  dot11 radio0

  Private SSID

  SSID Public

  dot11 radio1

  Private SSID

  SSID Public

  is a client given - that can automatically be capable - display/select the radio 5 GHz on the 2.4 Ghz?

  Specifically, when the 5 GHz capable client lists the available networks, I see only the SSID of the 5 Ghz radio, or is SSID for both radios generally displayed by such a client?

  Thank you.

  does a given client--which is capable--automatically display/select the 5Ghz radio over the 2.4Ghz?
  

  Depends on the settings of your wireless network card.  I've seen several wireless cards which allows you to specify which radio is preferred.  By default, the WNIC chooses the best available signal.

  Specifically, when the 5Ghz-capable-client lists available networks, does it only display the ssids from the 5Ghz radio, or are ssids from both radios typically displayed by such a client?
  

  N ° it displays the SSID that initially has the most powerful signals.  If an SSID is broadcast by the two 'a' and 'b' radio, the WNIC will only show a SSID.

• BlackBerry Smartphones why do I get multiple contacts for the same person

  Recently, when I add a new contact the 9700 creates several entries. When I delete these multiple inputs, then it leaves about 10 spaces. If I let multiple entries for the same person, the next person that I add only then indicates once

  Why they appear more than once?

  How can I delete multiple entries so they do not reappear when I create the following entry?

  Help, please

  Try a simple reboot and see if the empty entries remain.

  With the BlackBerry device powered time, remove battery for a few seconds and then reinsert the battery to restart.