My computer sends and receives information on unregistered ports

Similar Questions

• Why need a cable modem from a router can send and receive information to a computer?

  Why need a cable modem from a router can send and receive information to a computer?

  On Fri, 14 September 2012 17:14:59 + 0000, stuckfree wrote:

  Why need a cable modem from a router can send and receive information to a computer?

  A router is a device that connects computers (or other type of computer
  devices) to each other on a network and you can send files
  from one computer to the other. It does not connect to the internet, and
  you need a device called a modem vaguely to do this. The modem also
  connects to the router and allows the computers on the network
  (those connected to the router) to connect to the internet.

  However, note that there are some available devices that are
  router-modem combination. If your router is of this type, you do not have
  need a modem.

  Ken Blake, Microsoft MVP

• Is it possible to send and receive RTP streams on the same computer?

  Hi all
  
  I tried sending an RTP stream and receive it on the same computer, but it did not work. I use the AVTransmit2 and AVReceive2 classes, I assumed that these classes are popular, so I have not included the code for them) for this.
  
  It works perfectly fine when a computer sends using AVTransmit2 and another receiver using AVReceive2. However, when, on the same computer, I get the following error in AVReceive2:

   Cannot create the RTP Session: Unrecognized Windows Sockets error: 0: Cannot bind 

  The address I used for transmission and reception is: 224.144.251.104/22200
  
  And I also discovered that it IS possible to send and receive streams on the same computer using JMStudio, but I found it very hard to dissect its code.
  How can this be achieved using these two classes, that is, the AVTransmit2 and the AVReceive2?
  
  Any suggestions will be greatly appreciated.

  private String createTransmitter() {
  ...
  localAddr = new SessionAddress( InetAddress.getLocalHost(), port);
  destAddr = new SessionAddress( ipAddr, port);
  

  You can do this instead:

  localAddr = new SessionAddress( InetAddress.getLocalHost(), SessionAddress.ANY_PORT);
  

• Establishing a contact manager that is installed on my computer to send and receive e-mail.

  I Act 5.0 contact manager is installed on my Windows 7 Home Premium.  How do I put it up to send and receive messages?   I need of servers and port, right numbers?  What else?    Act 5.0 instructions are not accurate enough

  Try to contact the Sage support:

  Sage ACT! Support and training - wise in North America

• I have Error 0x800ccc0f and 0x800ccc79 codes then send and receive messages on outlook express.

  WHEN I TRYING TO SEND AND RECEIVE E-MAILS VIA OUTLOOK I GET ERROR MSGS. AS 'THE TCP/IP (S) CONNECTION WAS INTERRUPTED UNEXPECTEDLY BY SERVER' (ERROR No. 0x800ccc0f and 0x800ccc79 S.) MY PROTOCOL TCP/IP IN MY LOCAL AREA CONNECTION SAYS "OVER MY LAN CONNECTION SAYS"WINDOWS MANAGEMENT INSTRUMENTATION (WMI) INFORMATION MAY BE DAMAGED. " (1) (_1_) IS WHAT THE CAUSE, AND (2) WHAT ARE THE FIXES. P.S. I CAN ACCESS MY EMAIL VIA WEBMAIL FROM MY ISP.

  Original title: Outlook TCP/IP connection problems

  Hi TOMJR_3385,

  Thanks for keeping us posted and share this information with us.

  Please answer these questions-

  (1) what exactly happens when you try to access the internet?

  (2) don't you do a system restore?

  (3) that you get an error message or error code?

   

  I would like more information about the issue.

   

  Method-

  If you did not do a system restore, then you will need to perform one to cancel changes made to the computer.

  Check out the link-

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

   

  Note: Perform a system restore will cancel all changes made previously on your computer. You may also lose unsaved information as well. Proceed at your own risk.

  In addition, see the article-

  Error messages when you send and receive in Outlook and Outlook Express

  http://support.Microsoft.com/kb/813514

   

   

  Do get back to us and let us know if the steps of troubleshooting in help section. We will be happy to help you if you need help.

  Thank you.

   

   

• Send and receive mail in Windows 8

  Real simple question that I hope, but I was used to send and receive on Outlook and even able to find the settings so mail could be searched every minute but on Windows Mail, it is not so obvious, I think I have my mail configured to receive any time but it only downloads new messages when the application is opened after start so I have to restart my computer for new mail that is not ideal.

  Hello

  Thanks for posting your query in Microsoft Community.

  I imagine the inconvenience that you are experiencing and will certainly help you in the right direction to solve the problem. However, I would be grateful if you could answer a few questions to refine the question in order to provide you with better assistance.

  1. You did it any significant hardware or change software on the computer before this problem?
  2. Other applications to update properly?
  3. Do you use a proxy connection to connect to the internet?

  The question could arise due to incorrect e-mail account settings, updates pending or due to a problem with the application Mail or Windows Store. To diagnose and solve the problem, I suggest trying the following methods and check if the problem persists.

  Method 1:

  Step 1: Install pending updates.

  Check if there are pending updates to install.

  Check the link for updates pending

  Windows Update: frequently asked Questions

  Step 2: App Sync licenses.

  If a license for an application is not synchronized with the license installed on your PC, the application may stop working. To synchronize your licenses app, follow these steps:

  1. In the start screen, tap or click on Store to open the Windows store.

  2. Enter in the right edge of the screen, and then tap settings.
     (If you use a mouse, point to the lower right of the screen, move the mouse to the top and then click settings.)

  3. Tap or click App updates.

  4. Press or click on Sync licensing

  Step 3 : Delete the email account and to reconfigure the e-mail account in the app Mail see the following link to do.

  Messaging app for Windows

  If the problem persists, try the following method.

  Method 2:

  Download and run the convenience store of the App to the modern user interface. Also, try the additional steps described in the following link if the problem persists.

  Solve problems with a soft

  Method 3:

  If you are using a connection through proxy, then try to disable the proxy and then check if the problem persists.

  Follow the steps to disable the proxy:

  1. Open Internet Explorer
  2. Click the Tools button, and then click Internet Options
  3. Click the Connections tab, and then click LAN settings
  4. Uncheck the Server Proxy use.
  5. Click on apply then Ok to save the changes.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• How to use windows 8 to send and receive faxes

  Dear Sirs,

  My computer is running in the windows operating system 8.

  Could you help me put up my computer so that I can use it to send and receive faxes.

  Thank you.

  Kind regards

  Yoon Choy Loo

  Hi Yoon Choy Loo,

  Thanks for posting in Microsoft Communities.

  After your description, I understand that you need help setting up the windows 8 in order to send and receive faxes. Let me help you with it.

  Please follow the steps below to configure the fax:

  1. Hold the Windows key + C and type Fax and press ENTER.
  2. The Fax Configuration Wizard starts. Click Next.
  3. On the sender information page, type the information that you want to appear on your fax cover page. You don't have to fill in all the boxes. Then, click Next.
  4. The Fax Configuration Wizard displays the Select Device page to send or receive faxes. If you want to be able to receive incoming faxes, check the box to receive. If the telephone line you logged on to your computer is for faxes only, click on answer automatically after. If you want to manually answer incoming faxes, click Manual answer. Then, click Next.
  5. On the page of the Subscriber Identification (TSID), type the information you want in the TSID box. In general, it is a company name or your name and fax number. Click Next.
  6. On the page of the Subscriber called (CSID), type your information in the CSID box. The CSID that you enter is displayed on the fax machine of the origin of the fax. This number allows you to confirm that you send the fax to the right recipient. The CSID is usually the same as the TSID. Click Next.
  7. In the Routing Options page, choose whether you want to automatically print a fax. If you do not automatically print incoming faxes, they will be available in the Fax Console. Select Print on check box if you want each fax that you receive to be automatically printed. Then, click Next.
  8. End the SCW fax page, click Finish.
  9. The Fax Configuration Wizard closes and opens a Windows security alert. If you are prompted, click on unlock.
  10. Your computer is now ready to send and, possibly, to receive faxes. You can use the fax to go through the incoming or outgoing faxes, or upon receipt of a fax manually.

  Please follow the steps below to use the fax on windows 8:

  1. Open the document, Web page, or e-mail to fax.
  2. On the file menu, click on print.
  3. In the print dialog box under Select printer, click Fax, and then click on print.
  4. In the welcome in the Send Fax Wizard page, click Next.
  5. On the recipient information page, type the name of the recipient in the box to type the recipient fax number in the fax number box. If you want to send the fax to more than one recipient, type the recipient information in the appropriate boxes, and then click Add. The recipient appears in the list and the areas are cleared so that you can enter additional information about the recipient. When you have finished adding recipients, click Next.
  6. On the preparation, the cover Page, select Select a page template to cover with the following information box. Click on the model in the cover page template list. Fill area of subject line and, eventually, the box Notes . Then, click Next.
  7. On the schedule page, click Next.
  8. End Send Fax Wizard page, click Finish.

  The above steps will help you set up your fax machine and use the feature in windows 8.

  I hope that the information above helps you. Answer please come back for additional assistance.

• Thunderbird ceased to send and receive with the new update of Windows 10.

  Thunderbird ceased to send and receive e-mail. When I tried to send I got: "the message send failed.
  The message cannot be sent because the connection to the Outgoing server (SMTP) smtp.comcast.net was lost in the middle of the transaction. Try again. "My email loads on my tablet is not comcast. Firefox works is not my internet. Clues?

  Please start * Windows * safe mode with active network
  -win10 http://windows.microsoft.com/en-us/windows-10/change-startup-settings-in-windows-10
  Always in Windows safe mode, start thunderbird in safe mode
  - http://support.mozillamessaging.com/en-US/kb/safe-mode

  Problem disappear?
  Just reply to inform us of the results.

  Do you have non-comcast accounts where this does not happen?

• Yesterday, I could send and receive emails, today I can't. Webmail works fine. Help!

  I checked with my ISP. All settings OK and I can send and receive e-mails on the webmail and a windows mail IMAP account OK. ISP tech support said the problem is certainly in Thunderbird. Beginning yesterday it worked fine, but the night last and this morning I can't send or receive e-mails. I have not modified parameters.

  Check your firewall and make sure Thunderbird is not blocked. Sometimes an upgrade to a new version will appear in the firewall as a new program and it blocks.

  The webmail and client e-mail use server completely different so all it proves is that you know your user name and password.

  With regard to the correct settings, confirmed by the help desk, my more personal experience of the help desk cannot be a correct configuration if she got hit in the face. You can post your info troubleshooting here and maybe someone will be able to spot a problem. The title of the Help menu is troubleshooting Info. Then clear the check box to include personal information. Click on copy to C! ipboard then that stick to a window of response here.

  Given that you can't send or receive the prime suspect is the firewall.

• Wireless drops IE7 but emails still send and receive the Satellite Pro L20

  I will try to write this, so it is logic-

  Satellite Pro L20

  Card Atheros AR5005G Wireless - Driver version 7.6.0.130

  Windows XP, Office 2003, IE 7,.

  Router Netgear WGR614 v6 wirless.

  When using a product like Utorrent my conection sharing internet it falls P2P file comes with - cannot display the page - usually I select the network diagnostics and he responds with consult the manufacturer of your computer for help.

  E-mails still send and receive ok - my wife on her cell phone can still access internet ok (so I don't think it's a fault of router)

  After I close the application down and let it during 5 minutes to share files so I can access the internet. If I connect directly to the router via a cable that I have all of the problems that makes me think it's a fault of the wireless adapter

  Can anyone help?

  Thank you very much

  Alex

  Hello

  Eventually the large amount of data that occurs during the influences of P2P file sharing or Skype session of the internet connection.

  Sometimes this question is displayed on my laptop if 2 or three laptops are connected to the same router.

  However, have you tried a few solutions stallions like WLan driver updated for example?

  Please check the Toshiba Wlan portal and install the latest version of the driver:
  http://APS.toshiba-tro.de/WLAN/

  Good luck

• Send and receive messages question - Outlook

  Original title: saspencer

  Some forwarded messages sent out and go to the Outbox? This happens in Outlook.

  I also receive two duplicate incoming messages? Also, Outlook.

  Hi Steve,.

  Thanks for posting the request in the Microsoft Community.

  It would be great if you can answer the following questions:

  1 have had any changes made on the computer before the show?

  2. what version of Outlook are you using?

  If you use Outlook Express, follow these methods to solve the problem:

  Method 1:

  I suggest you to refer to the article and see if it helps:

  Error messages when you send and receive in Outlook and Outlook Express

  http://support.Microsoft.com/kb/813514

  Method 2:

  To resolve the problem with Outlook express, I suggest to refer to the article and try to fix it:

  An Outlook Express basic repair kit

  If the problem is not resolved, please answer and we will be happy to help you.

  Thank you.

• I have a question regarding windows mail. I was send and receive mail with no problems until last Thursday. I can still receive mail, but I can not send.

  / * moved from answers Feedback * /.
   
  I have a question regarding windows mail. I was send and receive mail with no problems until last Thursday. I can still receive mail, but I can not send. My email is with bellsouth.net and comes in my computer through windows Messaging.  I spent an hour and a half on the phone with bellsouth, and they say that the problem is with my windows mail.  I tried to use a restore date, and that did not help either. I will post a copy of this message, as I keep getting.  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Object 't', counts: 'mail.bellsouth.net', server: 'mail.bellsouth.net', Protocol: SMTP, Port: 25, secure (SSL): no, error number: 0x800CCC0F thanks for any help.

  Sometimes, WinMail settings get screwed up and you must remove the account and then add it back back.  Make sure first that the antivirus software not interfere (see www.oehelp.com/OETips.aspx#3).   Delete your account completely, then close WinMail.  Then compact and repair the database of WinMail (see www.oehelp.com/WMUtil/).  Add your account to mail back once again, and then make sure you have the correct settings under Tools | Accounts | Mail | Properties | Servers and | Advanced to what AT & T Specifies to WinMail (or OE).  Then see if it works.

  Steve

• Cannot send and received the error windows live mail 3219

  Cannot send and received the message of error windows live mail 3219 how remedy

  You use a hosted Microsoft e-mail address.

  Microsoft doesn't want you using a program like WLM.  I know, they created it, but they changed their minds.  They want to be able to use their webmail system so that they can put ads in your face and you profile by reading your emails.  They try to get you migrated to Windows 10 and the e-mail program integrated here.

  Most of my clients with addresses hosted Microsoft migrated far by pulling on the other non-Microsoft like Gmail or Yahoo mail addresses.

  WLM will work perfectly with these addresses.  Well more than half of my computer 150 customer use WLM 2011 version and it works very well.

• Bluetooth connectivity - although get all paired devices, but not able to send and receive any file.

  I always found the problem when connecting Bluetooth devices. Although that devices paired but not able to send and receive any file.

  Please guide.

  Hello

  Don't forget to check with your system/motherboard manufacturer Support as long as that
  the real peripheral manufacturer. Updated the BIOS and drivers from the chipset (both can affect the)
  BT) and BT drivers to their online resources.

  Read these:

  Why isn't Windows find my Bluetooth or other wireless devices
  http://Windows.Microsoft.com/en-AU/Windows-8/why-isn ' t-windows-conclusion-device
  Device advice
  http://www.Bluetooth.com/pages/device-advice.aspx

  Microsoft - hardware and drivers
  http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

  Why Windows is not find my device?
  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  What happens if a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  BluetoothView is a small utility that runs in the background and monitor the activity of
  Bluetooth devices around you. For each detected Bluetooth device, it displays the following
  information: device name, address, Major Device Type Bluetooth Type device minor, first
  Detection time, last detection time and more. BluetoothView can also inform you when a
  new Bluetooth device is detected, by displaying a balloon in your bar tasks or playing a
  a quiet sound signal. -FREE
  http://www.NirSoft.NET/utils/bluetooth_viewer.html

  BluetoothCL is a small console application that transforms all current detected bluetooth devices
  to the standard output. For each Bluetooth device, the following information is displayed:
  Address MAC, Minor Device Type, Device Type Major and possibly society
  name of the device (if the external file of MAC addresses - oui.txt is provided) - FREE
  http://www.NirSoft.NET/utils/bluetoothcl.html

  BluetoothLogView is a small utility that monitors the activity of Bluetooth devices
  you and displays a log of the devices in the main window. Whenever a new
  Peripheral Bluetooth comes in your area and when the appliance leaves your area, a new line of log
  is added the following information: device name, device address, time of the event, event
  Type ("Device arrival" or "Equipment Left"), Type of aircraft and the company that created the device.
  BluetoothLogView also allows you to specify a description for each device (according to her)
  MAC address) that appears in the column "Description". -FREE
  http://www.NirSoft.NET/utils/bluetooth_log_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Can I send and receive emails with Firefox?

  Can I send and receive emails using firefox?

  Firefox is not messaging components, but you can use webmail on sites like Yahoo! Mail and Gmail.

  Or you can use Thunderbird. https://www.Mozilla.org/en-us/Thunderbird/