My laptop computer and printer do not communicate with each other.
I went to "printers and devices in the control panel and my laptop has an icon of troubleshooting beside him. I tried to search for updates/drivers solve the problem and nothing works. It says ' unknown device is not a driver. My fax, copier and scanner work, but the printer does not work because there is a problem with my laptop. I could not use my printer because I was out of ink for 2 months, then I buy ink and now I can't print! Ink for a Lexmark is not cheap.
I hope someone can help!
Karen
Because my printer is a Lexmark, I had to go to the Lexmark he site and search "Drivers" under which specific printer, you have it downloaded on my computer and loaded this way to connect my laptop with my printer.
Tags: Windows
Similar Questions
-
Laptop computer and printer does not
My Dell Inspiron 1750 is not communicting with my Dell V313w printer. Jobs are stuck in the pile, troubleshooting cannot identify the problem, and I have tried everything I am well informed of (not much!) The printer itself works fine. Help, please!
Hello
Maybe you have that impression break - (I don't know your windows version) see here:
http://Windows.Microsoft.com/en-us/Windows7/view-pause-or-cancel-printing
If it's OK, try to look in this folder:
C:\Windows\System32\spool\PRINTERS
is it empty? otherwise remove all and restart your computer.
LC
-
Hi all
I have 5 wireless devices must connect to the router.
I want to divide it into 2 groups:
That is to say, 1, device A, B, C, group 2, device D, E.
I would like two groups cannot communicate with each other.
I've heard, it can be done by VLAN, is e2500 can adapt to what I need?
What about EA3500 and EA4500?
I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?
Thank you all!
Evil
Thanks for the clarification for the OP
FWIW
is this an alternative to routers that do not support of VLAN, to do what you want
-
AnyConnect Clients cannot communicate with each other
I have a problem that I've been pulling my hair out... my teleworkers connect to our network of Corp. via a connection AnyConnect VPN (version 3.1) to a Cisco ASA5520. I have not split tunneling enabled for this profile, so that all traffic should pass through the tunnel and all guests are in the same subnet L3... as far as their IP VPN address goes. The problem is the teleworker PCs cannot communicate with each other (pings/RDP/etc.). When I look at the newspaper I see traffic from one to another, have denied anything, but they do not communicate. My Network Corp., I can communicate with the two PCs Anyconnect very well. When I go to monitoring. ASDM itineraries I see each host that is connected to the ASA via Anyconnect, and the gateway for each is the default gateway of the SAA.
Am I missing some setting in the VPN profile that prevents the access between these hosts? I think that something come in the newspaper...
Have you enabled crossed and also a free NAT between AnyConnect users?
permit same-security-traffic intra-interface
network of the AnyConnect_users object
subnet
public static AnyConnect_users AnyConnect_users destination NAT (outside, outside) static source AnyConnect_users AnyConnect_users
If this does not resolve your problem, please post a sanitized complete configuration of your ASA.
-
ASA - Tunnel all traffic, allow rays to communicate with each other
Well, I hope someone can help me with this headache! Switching to employ a PIX and VPN 3005 concentrator Office at home in an ASA5510 for firewall and IPSEC tunnels. It is pretty much a
- VPN on a stick, multiple rays.
- All traffic sent by tunnel
- Internet access through main office (using the web filter) of
- VOIP to VOIP between rays
- All departments are using the clients VPN 3005 HW or ASA 5505 s
HEADQUARTERS: 10.0.0.0/24
Speaks 1: 192.168.11.0 / 24
Speaks 2: 192.168.12.0 / 24
Speaks 3: 192.168.13.0 / 24
-continues to 192.168.31.0 / 24
Spoke with the current configuration, 1 can communicate with all the resources in the home, office and Internet integrated properly checked by a tracert. However, the rays cannot communicate with each other. This is required for VOIP traffic, when all TALK TALK calls are made (sites).
Logging information when talk of talks initiated icmp:
- No group of translation found for icmp src, dst outside: 192.168.31.1 inside: 192.168.11.1 (type 8, code 0)
If I remove the nat (outside) 1 192.168.0.0 255.255.00 - rays will begin to respond to each other, but then the rays cannot tunnel through the Home Office Internet traffic. My brain is so scrambled after the cramming of VPN configurations for these days, so I hope someone has an idea. I've always used concentrators 3005, so it's a little different! In the search for documentation for this configuration, I was surprised that this isn't a most common topology. It seems that this article would (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805734ae.shtml), but there is no rays! In any case, I'm sure this has something to do with NAT rules and perhaps who need access for traffic list speaks of talking.
=============================================
ASA Version 8.2 (1)
!
hostname asa5510interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP address 97.65.x.x 255.255.255.224interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.0.0.40 255.255.0.0permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
the DM_INLINE_NETWORK_1 object-group network
object-network 10.0.0.0 255.255.0.0object-network 192.168.0.0 255.255.0.0
access-list sheep extended ip 10.0.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0
Allow Access-list extended wccp servers ip host 10.0.0.83 a
Redirect traffic extended access-list deny ip any object-group DM_INLINE_NETWORK_1
Redirect traffic scope permitted any one ip access-list
Global 1 interface (outside)
NAT (outside) 1 192.168.0.0 255.255.0.0
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.0.0.0 255.255.0.0Route outside 0.0.0.0 0.0.0.0 97.65.x.x 1
Route inside 192.168.0.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.2.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.3.0 255.255.255.0 10.0.0.1 1Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outdoorsCrypto-map dynamic dynmap 1 transform-set RIGHT
map mymap 65535-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400crypto ISAKMP ipsec-over-tcp port 10000
management-access inside
a basic threat threat detection
no statistical access list - a threat detection
no statistical threat detection tcp-interceptionWCCP web cache redirect-list Redirect-traffic group-list password xxxxxxx wccp-servers
WCCP 90 redirect-list traffic Redirect wccp servers group-list password xxxxxxxWebVPN
internal MJHIvpn group strategy
attributes of Group Policy MJHIvpn
value of server WINS 10.0.10.1 10.0.10.2
value of 10.0.10.1 DNS server 10.0.10.2
allow password-storage
Split-tunnel-policy tunnelall
mjhi.local value by default-field
allow to NEMusername field-3002 SjfS1Pq2xZGxHicx encrypted password
attributes of username field-3002
VPN-access-hour no
VPN - 250 simultaneous connections
VPN-idle-timeout no
VPN-session-timeout no
Protocol-tunnel-VPN IPSec
allow password-storage
type of remote access serviceremote access to field tunnel-group type
General-field tunnel-group attributes
Group Policy - by default-MJHIvpnIPSec-attributes of tunnel-group field
pre-shared-key *.class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the they
inspect the icmp
!
global service-policy global_policyHello Ala,
In Act got to be with the Nat configuration.
So basically you want to tunnel the traffic on the rays to communicate with each other.
OK, it would be with a nat 0 with the access list with the corresponding traffic outside.
Also on the crypto ACL for each site configuration, you must add an entry for the traffic of other offices.
I hope that I have explained myself.
Have a good
Julio
Note all useful posts!
-
I want to create a Web site with 4 child pages that interact with each other when opened separately on 4 different computers.Is this possible?
Example:
Child 3-page Web site open on 3 different computers with triggers and the following objectives:
PC #1 - child #1 - confirm button (trigger)
PC #2 - Page #2 - accepted Confirmation Popup, resulting by clicking on 'confirm' page computer/child #1 (target)
PC #3 - child Page #3 - calendar Popup changed, resulting by clicking on 'confirm' page computer/child #1 (target)
Any ideas are much appreciated.
THX.
No this is not possible with Muse.
-
Hi, I have the browser explorer Firefox and Internet on my laptop, a friend told me that they will be in conflict with each other. the question is what I would do abouth this.
Your friend has any idea. Both work very well.
-
Computer laptop Toshiba L505-S5990 will not communicate with my printer
Windows 7 and my laptop is no longer communicates with my wireless printer.
Manufacturers of printer general advice would be to disconnect / unplug the printer, then uninstall all printer via Add/Remove software, restart the PC. Then gets the latest version of the full version of the site of manufacturers of printer software and plug only / pwr on the printer when the installation says to
-
Hello ~
This question has probably asked a million times in a way or another, but here's my specific: I'm a laboratory for school. I've set up two virtual servers (Windows Server 2012) in VMware Pro 12. The goal is to speak (see others). According to the instructions of the teacher, I set them up as follows:
"Assign your appropriate servers of IP addresses based on your installation environment. For example, if your network environment uses the class C address range 192.168.1.x, assign a server IP 192.168.1.10, 255.255.255.0 subnet mask, a default gateway 192.168.1.1 and the other server IP 192.168.1.11, 255.255.255.0 subnet mask, a default gateway 192.168.1.1. Note: If these IP addresses will conflict with your internal network (provide your virtual machines with access to the internet), please choose a different set of address that will work for you. »I need to know what will work addresses. got a domain controller DC1. Now, I can't see each other. I can't connect to Internet via IE which is one of the 'evidence' that I'm supposed to provide.
When I go to the Publisher, I see as the guest only parameter (how is it said to set up when you first install the VMs) is 198.162.150.0. I did not who, but I'm a little but I don't want to make things worse by changing things. I guess that's where the problem is, but I'm not sure what to put the IP, default subset mask and DNS for so I'm stuck.
If it means anything, it is in fact on a borrowed laptop which is connected to the WiFi and wireless. The laptop has internet but I don't know how exactly bringing on the virtual machine when it come to be able to connect. I don't need to become an admin system; This is a compulsory course and I'm just trying to understand enough about it to pass. The problem is that other labs are constructed on it so I can't just ignore it.
Any advice you can offer would be GREATLY appreciated. By the way, happy new year to you all.Sorry, yes it was a typo. It's supposed to be 192.168.150.xxx.
Although the virtual machine must be able to communicate if they are both configured similarly (i.e. host only in this case), you generally EF IP addresses in the subnet host only for those virtual machines to be able to access it from the host, which - as mentioned earlier - should have an address of VMnet1 IP of 192.168.150.1.
André
-
How to create two separate networks in ESX that can communicate with each other with 2 x bear?
HelloJust want to know a fundamental question concerning the configuration of my ESX host of singlebox with several vswitch and two teddy bears,What is the definition or use of the network Label and ID of Port? Yes VLAN, I know what it's meant for the physical world.My goal here is to1. create several vSwitch with much 4 VM on the two vswitch and it communicate somehow vswitch0 and vswitch1 happen? I need to plug the switch of pNIC2 for communication can / must travel through the network cable in my ESX?2. how to force all traffic Vmthe in a vswitch to enter a virtual machine that runs as a router VM and then talk to the other router vswitch VM? is this possible?Thank you.I do not know if I understand perfectly, but I often have to create isolated networks.
In this case, there is only one NETWORK card, but it works with two, one on each switch. vSwitch0 can communicate with the outside world via the vmnic0. vSwitch0 and vSwitch1 are connected by the virtual router of pfsense. The virtual machines on the portgroup private connect to the world outside and any other VM on the portgroup VM network via the pfsense router. To access computers virtual private Portgroup requires a VPN connection via the pfsense router. This is a completely isolated network. With an additional uplink on vSwitch1, you can connect to other physical devices.
-
Two virtual machines to communicate with each other - intent an SMS Lab for test deployment?
Hi friends ,.
I am a new user and would like your help pretty desperately. The scenario is that I want to implement a SMS Lab to deploy the application from the server to a client and test the application. I have all the necessary knowledge to the packaging of application is concerned, and would like to help as much as VMWare is concerned.
I created two virtual machines and one of them will be configured as a server and the other will be the client. I created a team with these two machines in it. I am trying to ping from one machine to the other and its does not work. I only use the method of configuration host. The idea is simply to make the two systems communicate so that I can finish the entire configuration and use the same SMS deployment lab.
-First of all, I'm new to all this so I would like to know whther to everything I do is correct and what is the largest possible?
-What I have to do something else to make sure that those two communicate about someother or any other configuration software is necessary?
I would like to ask you guys to be a little more specific are you when you help others that I need you guys ore than a person who is used to working on VMWare.
And just so you know if it helps, I use VMWare Workstation 6.0.
What you are doing is reasonable. Both of your virtual machines have an IP address on the same subnet? In general, the scenarios no-ping, the first thing to check is the firewall in the guest computers. Have you checked that allows ping traffic? If it is disabled?
-KjB
VMware vExpert
-
2 separated on same ASA VPN tunnels can communicate with each other
Here's the scenario that I have a VPN tunnel with one of my remote locations. I also have a VPN Tunnel with a provider that supports the equipment for my organization. I need to have my supplier able to communicate with equipment that live in my other VPN tunnel. The two Tunnels are on the same ASA5540.
1 is it Possible?
2 How set it up?
Thank you
Follow this link for example. Enhanced spoke-to-spoke VPN, allows the two tunnels ending to your asa5540 to connect, using parameter permit intra-interface with configuration accless-list permits traffic of each endpoint of the tunnel.
-
laptop to the printer does not communicate
wireless laptop will not print on a HP wireless printer.
Hi Peppercat,
1. what operating system is installed on the computer?
2. What is the number of the printer model?
3. do you get an error message?
4. what happens when you try to print?I suggest you try the steps from the following link:
Printer in Windows problems
http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows
(Troubleshooting) wireless printing Center
http://www.HP.com/global/us/en/wireless/troubleshooting.htmlIntroduction to wireless printing
http://h71036.WWW7.HP.com/HHO/cache/603643-0-0-225-121.html
Additional information:
Why can I not print?
http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print -
Printer will not communicate with the computer.
Original title: printer nocomunicate
my printer Lexmark4200series Mod.x4270 and my compurete Compaq Presario5300no communicateLexmark confirms that the version of your installed printer software is supported in IE9 (yet)?
-
Lexmark X 5495 all-in-One Printer will not communicate with Acer running Windows 7
I have an Acer with Windows 7 installed, allowing no communication with my Lexmark X 5495. The Lexmark works very well and I was able to copy when you use a laptop with Vista installed. I tried uninstalling and reinstalling, fixation with recommended updates and it still has a communication problem. I also got a new usb cable which was obviously not the problem.
Hello
Have you checked to ensure that they support this device on Windows 7 and there are no known issues with Lexmark?
http://support.Lexmark.com/index?page=home&locale=en&UserLocale=en_US
If they do not support this device on Windows 7, here are some things you can try.
http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility
http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
Tell us what you find.
Concerning
Maybe you are looking for
-
How can I uninstall Windows XP
I am about to install Windows XP Professional in my office. I got this from the internet and I'm not sure of its reliability. If a problem occurs during installation or if I'm not satisfied with it, how can I completely remove it from my hard drive?
-
My Windows XP SP3 will not start
Hello Today my PC under Windows XP Home Edition SP3 froze with the BSOD and I was forced to do a reboot. Unfortunately I do not have a note of the problem, but I remember SRTSP. SYS that is mentioned. On reboot I tried to enter the mode safe to loo
-
system will not start, I have not connection wired, software was on the laptop at the time of purchase.
-
How can I reinstall Windows Media Player 11 for Vista?
I deleted by Windows Media Player 11 error. Even when the Player opens, it is not possible to stream live video. I tried to reinstall it by downloading from Microsoft, but it is not possible. Is there another way to reinstall Windows Media Player 11
-
I use my printer for a caravan club, printing envelopes, forms, leaflets etc. What I want to know is how much electricity my officejet 6700 consumes during printing. I print as much as possible about the project to save the ink. I print on 150-200