My PC and the diagnostic system Test screen

Similar Questions

• How to make a copy of all the software and the operating system that came stock with the laptop?

  I have a laptop that I have replaced the motherboard and now HD took a dump and should be replaced also. I need the software and the operating system disk, so I can restore the operating system to order.

  Please advise!

  This link will take you to a web document that explains how to order a recovery for the initially installed operating system disk.

  Here is the support for your laptop computer portal.

  Best regards

  ERICO

• Stop the random system, blue screen.

  Hi, my computer is windows 7 64 bit. for the past few months, my computer has been stop randomly, for example, while playing games, often it works fine. However, many times my computer just freezes and produces a continuous noise of stuttering. When I try to reset, sometimes it restarts successfully, and sometimes it isn't. my computer is an Acer Predator G5910. When I try to reset, it would not produce beep sounds and the little blue light does not appear. I wanted to wait a while later to restart. the computer freezes often also when I don't do anything. for example, if I went to the bathroom and to the left of the screen nothing running home computer, it would freeze again and I have to reset. Blue screens recently have popped up but disappear too fast for me see whats on it.  and sometimes, my computer works perfectly well. I have no idea what still recently, we used our warranty and they said they changed everything inside the computer. It is one of the technical information, I received in the blue screens: 0x0000001E (0xFFFFFFFFC0000005, 0x0000000012DA0D60, 0xFFFFF8800F2D68C8, 0 x 0000000000000000)

  nvlddmkm.sys - address FFFFF8800F2D68C8 base at FFFFF8800F278000, DateStamp 503f8bb8.
  There was no stop code.  I would really appreciate if someone could help me in this situation. I also want to clarify that I am not a professional on computers.
  Here is the link to skydrive for the latest dump files, that I could find.
  : https://skydrive.live.com/?cid=5c4d5ca7c75785d3#cid=5C4D5CA7C75785D3&id=5C4D5CA7C75785D3%21174
  Thanks in advance!

  Hello

  We have three audits of bug:

  LEAPC_INDEX_MISMATCHERREUR (1)

  This indicates that there is an inconsistency in the index of State APC.

  This is an internal error in the kernel. This error occurs at the output of a system call. One possible cause of this bug check is when a system file or driver has a sequence do not call system to enter or leave the regions controlled or critical.

  -It is usually hardware related bug control.

  System_service_exception (3B)

  This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.
  
  This error has been linked to the excessive use of expanded memory and resulting from user mode graphics drivers enjambment and passing data incorrect of the kernel code.

  Nom_image: material

  MODULE_NAME: material
  
  0: kd > fffff880018c7548 ln
  (fffff880'018 c 7530)   ndis! ndisOidSendToMiniportDirect + 0 x 18 |  (fffff880'018 c 7620) ndis! ndisFQueueRequestOnNext

  ^^ It seems that the exception occurred in ndis! ndisOidSendToMiniportDirect + 0 x 18.

  PAGE_FAULT_IN_NONPAGED_AREA (50)

  This indicates that invalid system memory was referenced.

  Bug control 0 x 50 usually occurs after the installation of a faulty hardware or installation failure of material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  -----------------

  1 Intel Extreme Tuning Utility - Office control - uninstall as soon as possible.

  2 make sure you have the latest video card drivers. If you are already on the latest graphics card drivers, uninstall and install a version or a few versions behind the last to make sure this isn't a last number one driver. If you have already experienced with the driver of the card later and earlier versions, please try the driver beta for your card.

  3. If you're still crashing after what above, run Memtest for NOT LESS than 8 ~ (several hours):

  Memtest86 +:

  Download Memtest86 + here:

  http://www.memtest.org/

  Which should I download?

  You can either download the ISO pre-built you want to burn to a CD and then boot from the CD, or you can download the automatic installer of the USB. What this will do is format your USB drive, make a boot device and then install the necessary files. Both do the same job, it's just you that you choose, or you have available (be it CD or USB).

  How Memtest works:

  Memtest86 writes a series of test patterns for most of the addresses of memory, reads the written data and compares it to find errors.

  The default pass is 9 different tests, varying in the modes of access and test data. A tenth test, bland, is selectable in the menu. He wrote all the memory with zeros, then sleeps 90 minutes before checking to see if the bits have changed (perhaps because of refresh problems). This is repeated with all those for a total time of 3 hours by pass.

  Many chipsets can report RAM speed and timings by SPD (Serial Presence Detect) or EPP (Enhanced Performance Profiles), and some even support changing the expected memory speed. If the expected memory speed is overclockee, Memtest86 can test that memory is free of error with these faster settings.

  Some hardware is able to report the status of the "PAT" (PAT: active or PAT: disabled). This is a reference to the Intel performance acceleration technology; There may be the BIOS settings that affect this aspect of memory synchronization.

  This information, if it is available for the program, can be displayed via a menu option.

  Other questions, they can most likely be answered by reading this excellent guide here:

  http://Forum.canardpc.com/threads/28864-FAQ-please-read-before-posting

  Kind regards

  Patrick

• Can I remove the diagnostic system reports?

  As above.

  Can I remove Diagnostic system reports that sit in the Console?

  Actually, can I delete everything in the Console?

  Thank you.

  You can remove these log files if you want, but they are generated automatically so that they will come back.  And there is already a purge calendar built into OS X to limit the size of the console of newspapers.  Unless you are desperately short of disk space, there is no advantage to clear the logs from the console manually - let the regular daily/weekly/monthly maintenance scripts to take care of purge of old files.

• VMware - script the creation of the vm and the operating system installation process

  Hello.

  Trying to determine the exact steps to automate the entire process of creating a virtual machine, and install a linux OS (Rhel/Centos) in the virtual machine. I need to understand the steps to do it entirely from the CLI using scripts. I have seen a few sites that describe the basic process of creation of the VM, which appears to generate the vmdk file.

  I've seen nothing that shows what needs to happen to install the operating system in the virtual machine, in the CLI. This process should be auto/programming, so I can't use the GUI.

  I imagine that the whole process will have to call the process/kickstart file and start from that somehow, but I don't see how the elements fit. The goal is to then have a VM with the required OS/Apps that are then run / deployed by external users on their machines.

  If this process can work, then we can talk to a Council-expert/vmware on the next phase of the project.

  Answer that be detailing how to proceed, or point of item/sites on that would be great!

  Thank you

  I just tested on a Linux system and had to perform the installation of VMware VIX - 1.10.1 - 266898 two times.  It is not the first time without any message in the log file.

  After a successful installation, I ran a .vmx without first modifying the /usr/lib/vmware-vix/vixwrapper-config.txt file and received the error message waited on the specified version was not found and then after editing it, I was able to run the .vmx using vmrun nogui.

• Hard drive swapping and the operating system between two laptops of R61e

  I have a R61e who broke chassis. Not a left hinge broken, but broke up chassis where the left hinge connects.

  I have the opportunity to buy a used one with no operating system.

  Both are of type 7650 and all have two 80 GB hard drive.

  Will it work if I just reverse this HARD drive with the operating system for the new portable computer?

  Yes, it should work without major problems.

  In the worst cases, you need to update to a couple of pilots.

  Good luck.

• How can I move my files and the operating system on a new hard disk on Inspiron 580 s.

  My hard drive failed Diagnostics recently and needs to be replaced.  I have since installed a new hard drive in Bay 2. I need to move everything from the old drive to the new drive and delete the old which is completed. So what is the best way to go about this?

  pjrl

  The simplest method, I prefer to install a replacement hard drive, is to clone the existing hard drive to the new, that will also transfer all applications and programs.

  You need an imaging utility, similar to True Image Home 2015.

  http://www.Acronis.com/homecomputing/products/TrueImage

  Acronis resize partitions transferred to match the size of the new hard drive.

  Hard drive manufacturers, also have their own free cloning software available, but it can be used only with their hard drives.

  First, install the new drive as the secondary and the image of the main hard drive in it.

  Immediately after the cloning, shut down the system, switch the data cable [SATA port 0] to the new disk, making the new master hard drive and see if the system boots properly.

  Start the system with only the new hard drive connected.

  Be sure to leave the original drive disconnected, until the new hard drive is working to your satisfaction.

  Before cloning a hard drive, make sure that the existing drive has no corruption or virus on it, because they will be transferred to the new hard drive.

  It will take a second SATA data cable, there should be a spare connector to SATA power inside the housing.

  Bev.

• Storm blackBerry Smartphones and the alarm reset alarm screen

  I have a Storm 9530 with Verizon that I bought in February.  My phone works through a BES at work, but it's my personal phone.  I use my phone every day to wake up and, until last week, I never had problems.  At some point, setting the alarm on my phone started to challenge on the eve and he continued to do so through today.  For example, my alarm Wednesday was from 06:00 (the last day it worked correctly).  Wednesday night, I set my alarm to be awakened at 6:30 the next morning my phone alarm went off at 6:00, and the wallpaper in the home screen has been reset.  My alarm Friday from 06:30 was also and it went very well, but the wallpaper has reset.  Friday night, I set my alarm at 7:15, but it exploded at 6:30.  Saturday night, I set my alarm Sunday morning from 07:45 and the alarm went off at 07:15.  I talked to Verizon first Friday and they had put me on level vers.148 (I utilisais.75 with no problems) and setting the alarm continued to reset.  I spoke with a different tech Verizon today and they said it's a problem with BES pushing some type of reset on the phone.

  I'm new on display and thought that maybe someone could point me in the right direction.

  It seems that your BES profile is messed up. Can perform a backup, do a security wipe and perform a selective backup only the important things. Stay away from the options database. Download your IT Department to remove yourself from the BES, turn off your profile and you readd. Then re-enable the BES.

• Is there one GUI, other than Assistant Deputy Ministers, and the CSM for test site vpn to ipsec tunnels on an asa5505/asa5510?

  Is there a GUI, other than the Assistant Deputy Ministers and the Security Manager cisco IPSec of Cisco ASA5505/5510 test site to vpn tunnels. I usually go through the steps listed in here in the link below in the terminal window, but it sucks when you have several tunnels to keep abreast of.

  http://www.nwdump.com/troubleshooting-IPSec-VPN-on-ASA/

  I would have preferred one that works with Freebsd or LInux, as the cisco security manager CSM v4.1 is limited to only current running on windows server 2008 ent.

  Thank you

  Jason

  No, for troubleshooting the best way is to use the CLI that will give you debug output on where it is lacking.

  For configuration, outside the CLI, ASDM and CSM, unfortunately there is no other tool that works on Linux/Freebsd because it is more specific orders of the ASA and only limited to the CLI, ASDM, or CSM.

• CS5 and the operating system upgrade to Windows 10

  I have Photoshop CS5 running on Windows 7 X 64. My operating system will be upgraded to Windows 10 in late July, through Windows Update. It will break my installation? I need to block the upgrade?

  Permanently disable before even trying! The activation system just don't like the changes made to the system, and most certainly will not work afterwards. A reinstall of the CS5 will probably be necessary anyway.

  Mylenium

• Windows vista cannot open network, the Task Manager and the windows system restore.

  I have problems with a computer, I'm trying to fix. It is a Dell Inspiron 1420 with windows vista. Whenever I try to open the networking or system restore, I get a window with a white screen. With this blank screen, it's like the computer is frozen, ctrl alt del, break the gel, but when I try to open the Task Manager, it would not come. Another problem is blocking down. Stop taking too long. (maybe 30 min)   I did research on the internet to find what could cause something like this and a way to solve these problems, but I came empty. Any information or suggestion would be useful.

  Hi Wiseman504,

  -How long have you had this problem?

  -What software changes you did on the computer before the show?

  Follow these steps:

  Method 1:

  Step 1:

  Boot in safe mode with networking and see if the problem persists.

  See options (including safe mode) advanced boot for instructions on how to start in safe mode with network.

  Step 2: If the problem does not occur in safe mode, start your system in a State of clean boot (in normal mode) to solve the problem.

  For instructions, see How to troubleshoot a problem by performing a boot in Windows Vista or in Windows 7 .

  Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

  Optimize Windows Vista for better performance

  Ways to improve your computer's performance

  Method 2:

  Follow these steps:

  Step 1:

  Create a new user account and see if the problem is recurring in the account newly created.

  Step 2:

  If the problem does not persist in the new user account, it could indicate that your old user account is corrupted.

  Follow the steps in the following article to repair the damaged user profile:

  Difficulty of a corrupted user profile

• Upgrade to XI and the C 'system' command stopped working?

  I developed an addon easy to launch an application from drive (giving it the doc currently open as a parameter). This works very well with Adobe X but not at all with XI.

  The code is essentially:

  int a = system("C:\\test\\text.exe");

  If (a! = 0)

  {

  sprintf (str, "could not find application (%d)", has ");

  AVAlertNote (str);

  }

  ... return is - 1

  I tested on two computers (two Win7) - the plugin works as expected in the X, but not in the XI.

  The plugin is triggered in both - I put AVAlertNote in and they pull all the way - the only difference is that in X, it returns 0 and opens the application, and XI, it returns-1 and does nothing.

  I really need the plugin works on X and XI - I'm doing something wrong? Security settings changed from X to XI?

  Thanks in advance for any advice,

  DOM

  I wonder (but I don't really know) if that could be affected by the protected sandbox sand. I thought that plug-ins have been disabled in safe_mode anyway, but maybe not...

• Advantages and disadvantages of adding programs and the operating system windows to mac?

  For a long time Windows user., new Mac user. What are the advantages and disadvantages of the addition of the windows operating system and programs for the MacBook Pro? I use word and excel regularly, but not yet sure I want or should add capacity to my new Mac.

  If you need Windows programs that don't have any equivalent of Mac, there is nothing wrong with it.  I have not because I didn't need Windows programs.

  But...

  If you do, you must decide if you need full-system-resources (Bootcamp, boot sector corrupted system, OSX will sleep while Windows is running) or just one-environment virtual (VM, share system resources, runs as a 'guest' to OSX at the same time as OSX).  Bootcamp will have part of your partitioned drive so make sure you have spare disk space.

  And if you go Bootcamp, position and spend time in the Bootcamp Boot Camp forum where lonely T is an expert who can guide you.

• To report a local name and the value to test.

  Hello!

  I have a local variable in MainSequence what name and value I want to include for the test report. How is that possible?

  ARO

  Jick

  Solved!

  Step.Result.ReportText = Str (Locals.LimitFileVersion)

• I need help and I did everything but replace my computer and the operating system.

  I invaded by the windows updates, drivers, hardware (found and installed by administrators network supposed recntly) IE9, won ' t hold my settings and my user rights change daily.  I can even find another computer in the supposed network, which I have added.  While trying to burn a backup cd, two days ago my computer started smoking and my blue ray player was no longer working.  I found an extended partition on my drive that I cannot format and cannot be accessed.  When I reinstall, as soon as it starts the first time, there are programs and updates already made, but I can't get an internet connection.

  Hello

  If the computer is in a domain environment, then please contact the system administrator or network administrator to get it resolved.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums

  http://social.technet.Microsoft.com/forums/en/category/w7itpro