NB305 - what settings should I use to get 11 hours of battery life?

Similar Questions

• What ports should I use to get the VPN RA worked?

  Hello

  I have a few tunnels l2l. I don't use "vpn sysopt connection permit" command. I prefer to activate the required ports for specific source IP. So they can establish the VPN tunnel with me.

  Recently, I have configured remote access vpn. It is work very well... But only when I activate "vpn sysopt connection permit.

  Question:

  1. what ports need to be activated to get RA VPN work? (without vpn sysopt connection permit)

  2. How can I restrict the access of remote when clients they connected to my private network?

  Thank you

  Leo

  Hi Leo,

  When you are not using 'connection sysopt... '. ", you must explicitly permit udp 500 and udp 4500, traffic esp on the outdoor access list.

  Let's say that public intf outside ip address is x.x.x.x and pool customer, we use y.y.y.0 and you want to allow 'only' traffic for port 80 through the tunnel.

  In the ACL on the outside, you need the following instructions:

  access-list 101 permit udp any host x.x.x.x eq 500

  access-list 101 permit udp any host x.x.x.x eq 4500

  access-list 101 permit esp any host x.x.x.x

  access-list 101 permit tcp y.y.y.0 255.255.255.0 eq 80

  access-list 101 deny ip 255.255.255.0 y.y.y.0

  * Please indicate the post if it helps.

  -Kanishka

• What settings should I use for the rear button focus put in place for the d5 mark 3? TIA

  5 d Mark 3

  When you press the menu button, highlight on (using the knob on the front of the camera) menu "C.Fn2: disp.» "/ Operation" orange. (it's the icon of a camera that has an index of points for a light meter below - right of the wrench, to the left of the star icon).

  Each of these menus on the 5 d III have several pages.  This is the 2nd page (the 2nd point from left to right) who has the category of "custom controls".  Note that (using the wheel on the back this time) and click on the set"" button.

  Which displays a menu showing each of the important controls on the back of the camera and what they do.  Highlight the icon for the shutter button (this modifies the behavior of a half-press) and change to 'measure and AF start' to just 'start of counting.

  "AF-ON" button (on the back of your camera) is probably already put 'measure and AF Start' (I think that this is the default factory setting).

  If you're not so much focus to enable back-button (which is probably already active) you're more "power off" the focus when the shutter button is pressed to halfway.

  Good luck

• What settings should I use to start my computer without using a password any

  I tried to start my sons computer but he doesn't remember his password. While trying to solve this problem using my computer, I now use a password, I had put in place to start without sigining with a password. I want to be able to do this again.

  http://www.SevenForums.com/tutorials/377-log-automatically-startup.html

  And for your sons PC

  http://superuser.com/questions/72244/what-can-i-do-if-i-forgot-my-Windows-password

• What setting should I use to send an age of E is also clear that it is in LR?

  What settings should I use when I send an edited image of LR?

  My images are clearly in LR, but an e-mail image is blurred.

  SOS!

  And check the options in the e-mail dialog box-

  

• My laptop stopped recognizing wireless function. What drop-down list function should I use to get it to recognize wireless again?

  My laptop stopped recognizing wireless function.  What drop-down list function should I use to get it to recognize wireless again?

  Hello

  What is the brand and model of your laptop?

  Follow the suggestions and check out them.

  Method 1

  You can follow the procedure in the article.

  Enable or disable a network adapter

  http://Windows.Microsoft.com/en-us/Windows-Vista/enable-or-disable-a-network-adapter

  Method 2

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  See also:

  Network adapter problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

• Can I string my new imac to 2015 to my imac 2007. What cable should I use (read: I'm illiterate cable).

  Can I string my new iMac to 2015 to my iMac 2007. What cable should I use (read: I'm illiterate cable).

  Hi, Daisy Chain in what way, exactly, do you mean so the iMac 2007 may be in target disk Mode so the newest can use its drive?

  If so, you need a lightning to Firewire adapter...

  http://www.Apple.com/shop/product/MD464LL/A/Apple-Thunderbolt-to-FireWire-ADAPTE r

  And a FW/800<->FW800 cable...

  http://eShop.MacSales.com/item/NewerTech/1394B99036/

• Need software to print on my new PIXMA PRO - 100 person knows what software should I use?

  Need software to print on my new PIXMA PRO - 100 person knows what software should I use?

  Help or the link will be much appreciated.

  Thank you.

  "My printer" supplied with your Pro-100 can do DVD.  You can use their templates or create your own. You can import your own images and make any way you want. Look at the stuff you already have.

• I want to download a file of contacts which should support non-Western (double-byte) characters, what format should I use?

  I want to download a file of contacts which should support non-Western (double-byte) characters, what format should I use?

  Hey,.

  You must save your file in Unicode text format. File in text format is Unicode supports non-Western characters (two bytes).

• I have questions on the use of the commercial license... Which forum should I use to get answers or how I can get in direct contact with adobe?

  I have questions on the use of the commercial license... Which forum should I use to get answers or how I can get in direct contact with adobe?

  I have my answers! The chat feature did not work well... But I had contact, so everything is good now!

  Thanks again!

• What open firmware source for my valet M20 more should I use to get the internet to an xbox 360?

  I have a Valet more M20 I want to use to connect my xbox 360 to the internet. I want to use it instead of getting a wireless adapter for my xbox 360.

  Should I use Freifunk, openwrt or something else. DD - WRT seems to be updated more so I don't want that one, and I don't think it's compatible anyway.

  Thank you for your time.

  Hello

  Please ask your question in the Xbox forum.

  http://www.Xbox.com/en-us/forums

• What drivers should I use for HP Envy 4 on Windows 8?

  1. number and product name
  HP Envy 4-1054TX

  2 operating system installed
  Windows 8 Pro 64-bit

  3. error message (if any)
  

  4. all changes made to your system until the problem occurred
  Upgrade to Windows 8 Pro to Windows 7 Home Premium, 64-bit versions

  I have recently upgraded to Windows 8 Pro and there are only 2 drivers available on the site for my laptop model: the Wifi and Bluetooth drivers.  Most of the drivers have been installed by Windows 8, but there are 2 elements in the devices without a driver, PCI Simple Communications Controller and another unknown device manager.

  There are some drivers for the Intel 4000 and HD 7670 m but I did no switchable graphics.  There is no center of control of AMD, Intel just one.

  To make things worse, my battery life has been reduced to 3.5 hours of 5.5 or 6.0 hours when using Windows 7.  I did all the usual settings in the power settings advanced, as well as for the Windows 7 install so the only thing I can think of is maybe the drivers from the chipset?

  Any help I can get would be appreciated.

  Hi brightframe,

  Take a look at this document http://goo.gl/CO6uV , which covers some information, including topics on driver problems.

  More than likely HP won't to material support for W8 on any system purchased before October 1, 2011. Some updates for W8, most drivers W7 will work in W8.

  For anyone with Windows 7 and given update on Windows 8, can run the Upgrade Wizard software, it will scan your PC and report on what is currently installed on your PC is compatible with the W8.
  http://goo.GL/z8LVf

  Please let me know if it helps.

• Order WMI - what command can I use to get the temperature of the GPU?

  Which command can I use to get the temperature of the GPU in WMI?

  Hi Daniel_99,

  ·         Do you use some kind of scripts?

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP forum.

  http://social.technet.Microsoft.com/forums/en-us/category/windowsxpitpro

   

  I hope this helps.

• That must make the password stored in the JAGENT portfolio, and what JAVA_HOME should I use for the pw_agent_util.sh command?

  I configure the GoldenGate Plugin for OEM. There is a step to create the portfolio. The documentation is not clear on the role of the provided password. If I run the JAGENT as user oracle, it must match the password for the oracle user, or is this separate password? Also, should I use the jdk to OEM agent to set JAVA_HOME?

  ./pw_agent_util.sh - jagentonly

  Pat,

  Morning.  Good to see that someone is working on the use of the plug-in for GoldenGate in OEM12c.

  If you use the plugin 12.1.0.2, you will be much better with the preparation of reports on the processes of GoldenGate.  In order to get the 12.1.0.2 plugin to work, the 12.1.3.0 JAgent is necessary and can be downloaded in the distribution of the Oracle GoldenGate monitor (Agent Monitor configuration Oracle #GoldenGate |) DBASolved).  If you use the old plug-in 12.1.0.1, the JAgent is integrated with the GoldenGate Software (Oracle GoldenGAte(11.2.1.0.1 and later) and Oracle Enterprise Manager 12 c |) DBASolved).  I recommend you take the new plug-in!

  Now to the address that ask you the password. The password is stored in the portfolio under the House of GoldenGate ($OGG_HOME/dirwlt) and is used directly for the JAgent to connect to the EMAgent and connect with OEM.  The password associated with user name is configured in the $JAGENT_HOME (different depending on version, look for the Config.properties).  Then in OEM, the user name defined in the Config.properties and the password in the portfolio must be provided before OEM GoldenGate targets will come.

  The $JAVA_HOME parameter is dependent on the version of JAgent you want to run.  The JAgent 12.1.3.0 to using the JDK 1.7 or higher.  The JAgent shipped using JDK 1.6.

  Thank you

  Bobby

• When I try to download photoshop CC, I ask for an application to download with. What application should I use?

  I tried to download photoshop CC. When I click on download, I wonder for an application. What should I use? I can't understand how to download this. Help, please!

  You must install the creative cloud application.

  Mylenium