Need Board SPARTAN 3rd driver for Labview FPGA 8.5! THX

Similar Questions

• 64-bit driver for LabVIEW FPGA Xilinx SPARTAN 2009 3rd starting Board

  My dear I need this add-on

  We I install the module i hava, it seems

  Support for LabVIEW for Spartan-3E (incompatible with the 64-bit platform)
  is their a supprt 64-bit version?

  Best regards

  Hello mangood,.

  There is unfortunately no way to use the driver on 64-bit Windows. You will need to use the 32-bit operating system to use the Spartans drivers. Sorry for the inconvenience.

• Spartan - 3 driver and Labview FPGA 2009

  Hello

  Do we need a new Spartan-3E driver to work with Labview FPGA 2009? And, if so, is it provided by National Instruments?

  Thank you

  Walid F. van

  Hello everyone

  The driver for the Spartan 3rd WHAT XUP Starter Kit are now on the site OR here:

  http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

  Just click on the link to get driver.

  Kind regards

  John Harvey

• CLIP IS taken in charge by Xilinx Spartan3E driver for LabVIEW 8.6?

  CLIP IS taken in charge by Xilinx Spartan3E driver for LabVIEW 8.6?

  For the HDL interface node, enable and multi channel clock domain is difficult to understand

  New version of driver that supports the CLIP is displayed: ftp://ftp.ni.com/evaluation/academic/spartan.zip

  First uninstall your current version and then install it.

• A60: Need to download the driver for powersaver

  Hi there I have recently upgraded to windows xp pro, I have a toshiba A60 and I need to download the driver for powersaver. Is someone can please tell me why this is not possible, as at the end of the installation it says fatal error.
  Any help will be much appreciated.

  Hello

  Have you downloaded the latest version of the power utility of Eve from Toshiba download sites?
  Please see this site:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Good bye

• Need Win XP AHCI Driver for my Satellite L500d-159

  Need of WXP AHCI Driver for my Satellite L500d-159

  Thank you

  Hello

  Satellite L500d-159 seems to belong to the series of PSLT9E.
  European driver Toshiba page provides all the drivers Win XP!

  The laptop supports an ATI graphics chip and the graphics card driver contains the SATA/AHCI driver as well.

  Then download the graphics of the page of the European driver Toshiba driver.
  In the package, you will find only the exe file run this exe file after the package was extracted, you will have to go to the SBDrv\SATA folder
  You will find the .inf file that is a SATA driver!

  Welcome them

• HP 250 G4: Need to Synaptics TouchPad driver for HP 250 G4 running Win 7 32 bit

  Hello

  I need a Synaptics TouchPad driver for HP 250 G4 running Win 7 32-bit. When I go on the site of HP driver and enter the product number and the serial number of my laptop all the getting is the driver for Win 7 64 bit. There is a 32-bit driver for Win 7?

  Serial No.: [personal information]

  Product no.: N1A78EA #ABU

  Thank you

  Sean

  Hello:

  The driver also supports 32-bit operating systems.

  I explored the driver file and there is a 32-bit drivers.

  Also, when you explore the driver folder, you will find this document I zipped upward and the joint below...

• Need to find a driver for NETWORK card for my P7-1010

  I had a few difficulties to connect to my cable company and they said that it's maybe because I didn't install the necessary NETWORK card driver. That sounds wrong and if so, where can I find 'he'... or all the other drivers, I may need. Is there a central database driver? PS - I am born a Mac person and due to costs and conditions of work ended up on a PC... and I've had hundreds of issues with both platforms... but less Apple... so do not hate the user ID

  For what operatng system you need the NETWORK card driver for?

  All drivers available for your desktop P7-1010 PC are stored here.

• I need a 64 bit driver for my scanner: Epson Perfection 2580 Photo. Any ideas? Epson told me that they can't have a 64-bit version of this software...

  I need a 64 bit driver for my scanner: Epson Perfection 2580 Photo.  Any ideas?  Epson told me that they can't have a 64-bit version of this software...

  Http://www.hamrick.com/ VueScan supports the 2580 Perfection but is not free.

• Windows 7 says I need to install this driver for the scanner to work, but I can't. HP m1522nf driver wia

  Windows 7 says I need to install this driver for the scanner to work, but I can't.

  As for all the HP drivers, simply visit the HP support site http://support.hp.com/, enter the model number in the search box, click on the link drivers and you're there.  http://h20000.www2.HP.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=3442754&lang=en&cc=us&TaskID=135&prodTypeId=18972&prodSeriesId=3442750

• my internet connection has been cut, and then I tried to find out. I opened the Troubleshoot, it says that I need to install a driver for my network card. I use Windows 7 Ultimate.

  Two days ago my internet connection has been cut, and then I tried to find out. I opened the Troubleshoot, it says that I need to install a driver for my network card. I use Windows 7 Ultimate. What should I do? Should I re install windows 7 ultimate on my computer?

  Hello

  What brand / model of the computer?

  There is no need to re - install Windows 7. You just need to install the network card drivers. Check out the link and follow the steps.
   
  Automatically get recommended drivers and updates for your hardware
  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware
   
  Update drivers: recommended links
  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

• I need to download a driver for Lexmark X 5495

  Original title: Windows 8

  I need to download a driver for Lexmark X 5495

  Get the victory 8 driver and software to Lexmark support if they are available. If this isn't the case, you could try to install the version of win 7 using the compatibility mode. It might work and it might not. Check the Compatibility Center to see if you can use the printer in win 8.

• Question for LabVIEW FPGA DRAM

  Hi all

  How can I correctly address the 128 - bit DRAM memory?  I have the Bank DRAM 0 set as a memory of 128 bits, set up in my design as a CLIP.  I realize it's a wide RAM on 32-bit.  I had a National Instruments AE do the original design I've been adding to.  He said that the addresses needed to incrementing by four with each entry.  Example: if I had to write in consecutive addresses, I would write to the address: 0, 3, 7, 11, 15 etc, and I would like to send 128 bits to each address.  My address is calculated as: (number of pixels in a line of video + line * (number of pixels per line) for a picture of the video).  So I take my calculated address and add 4.

  However, I checked an example in the finder example: example of integrity hardware flexRIO/IO/external memory/memory.  In this example, 128-bit data is sent to the memory and the address is incremented by 1 (instead of 4) each cycle clock as valid data.

  Who is this?  Section of the help for this function is ambiguous.

  Sets the address in external memory for reading or writing. The physical data bus for external memory is 32 bits wide (4 bytes). Each unique address value represents 4 bytes of data. Therefore, the total number of unique addresses in external memory is equal to (Memory Size in bytes)/4.  
  
  Note  The memory interface exposed to LabVIEW FPGA is 128 bits wide. As a result, each memory write or read operation accesses four different address locations in memory. The memory controller latches this signal value only when you issue a new memory write command by asserting the Command_Write_Enable signal.
  

  I'm confused by the 2nd paragraph "every Scripture memory or read operation four access address locations of memory."  Does that mean I increment the address by 1 to get 128 consecutive bits 'locations' (Yes, I know, that's 4 words of 32 bits in memory), or do I increment the address by 4, in the order of words of 32 bits 4 by 128-bit single transfer?

  Thanks for your help.

  -J

  Hello J,

  I want to clarify my previous post.  There are two ways to access memory DRAM, CLIP (that you have described is what you do) and using the memory node.  As noted before, the DRAM is 128 bits wide.  When you write to the CLIP you basically write pieces that is the width of the databus (in this case 32-bit).  Therefore, when you write a total of 128-bit DRAM, you place 32 bits in each address.  The address being the width of the databus, then you write with a writing & the address 0, 1, 2, 3.  Then the next write will be 4, 5, 6, & 7 and then address 8, 9, 10, & 11 and so on.  In this case, you must increment your address by 4 whenever you write.  Note that you start at 0, then 4, then 8, etc 12.  In your previous post, you were out of a figure.

  There is also another way to write in the DRAM memory, and it is through the node of memory, which is what is used in the example that you are pointing out.  Here, LabVIEW takes on some of the thought, and instead of being the width of the databus address, they are the width of the entire segment of 128 bits.  So when you write to DRAM here, you only increment 1 whenever address because they refer to any segment of memory.  This contrast with the CLIP, address 0 of the memory node interface match the addresses 0, 1, 2, 3 in CLIP mode & and address 1 of the memory node would correspond to 4, 5, 6, 7 in CLIP mode addresses &.  If you do not write an integer of 128 bits for the memory node, then the remaining addresses in the data block are filled with "junk" so that the address remains constant.

  As I mentioned previously, it is the most effective writing in chucks of 128 bits so that you don't waste all of the DRAM.  I hope you find this explanation clearer.

  Brandon Treece

  Technical sales engineer

  National Instruments

• Satellite X 200 - 21W, need a 32-bit driver for nVidia GeForce 8700 M GT

  Hello!

  I need a Vista 32 bit driver for my GeForce 8700 M GT. The toshiba driver is too old for Gears of War. The game requires at least the pilot 163.44. Anyone have any idea where I can get one?

  Thank you to

  Hello guys

  You can do what you want, but be careful with all these drivers Toshiba is not approved. As you know cell phones must be cooled properly and it there a lot of other factors is responsible for this. Toshiba sets different values and parameters of the graphics card itself and I heard that by the use of some third party drivers, these values can be changed and not only temporarily.

  The changed values in the graphics card BIOS may result with permanent running cooling fan, high temperature graphics card, and so on. Very interesting, is that there is no chance of getting the original values, even after the installation of operating system with supplied recovery media.

  I hope that something like this will not happen to you and you can use your laptop as before, but in my opinion you should think twice before using the drivers not approved by laptop manufacturers.

• Need FN and multimedia driver for Windows XP

  Hello

  I love this laptop!
  I need driver for the FN and the MULTIMEDIA keys (brightness, red led and so on).

  Please help me.

  I don't know what model of laptop you have exactly and where you bought it. I can't check the Toshiba download page, but you can do it alone.
  Your laptop is supported for Windows XP Home edition? Are WXP drivers, tools and utilities for Windows XP Home edition?