Spartan - 3 driver and Labview FPGA 2009

Similar Questions

• Need Board SPARTAN 3rd driver for Labview FPGA 8.5! THX

  Hello!! I need 3 spartan driver for labview 8.5 (not for labview 8.6) for school Ultimativa try to download from ftp://ftp.ni.com/outgoing/NISPARTAN3ELV85.zip
  but this link is dead now. Does anyone could send the driver to [email protected] PLZ? Thank you very much for all in advance

  kongleelk,

  You can find the file in the url above for a few days. Let me know if you have any problems.

• Drivers Xilinx/Multisim and Labview FPGA

  Where can I find drivers for my FPGA OR if I use Multisim/Xilinx and NOT of Labview?  All the links I found are Labview be installed.  However, the explicit manual FPGA indicates that you can use Multisim/XIlinx ISE in place.

  OK, I tested just outside. The Driver of LabVIEW 2013 DEFB contains 2 separate components, the driver and Module FPGA support. If you run this installer, it won't check if you have LabVIEW FPGA installed unless you check the box for LabVIEW FPGA support.

  I can change the text in the Installation Instructions to read "LabVIEW FPGA 2013 is required to install the LabVIEW FPGA Module Support component installation".

• What are the differences between LabVIEW and LabVIEW FPGA and LabVIEW RT

  I need a comparison of LabVIEW, LabVIEW FPGA, and LabVIEW RT

  Sorry, I misunderstood.

  LabVIEW RT (LabVIEW Real-time) combines graphical LabVIEW of programming with the power of a real-time operating system, allowing you to create applications in real time.

• 64-bit driver for LabVIEW FPGA Xilinx SPARTAN 2009 3rd starting Board

  My dear I need this add-on

  We I install the module i hava, it seems

  Support for LabVIEW for Spartan-3E (incompatible with the 64-bit platform)
  is their a supprt 64-bit version?

  Best regards

  Hello mangood,.

  There is unfortunately no way to use the driver on 64-bit Windows. You will need to use the 32-bit operating system to use the Spartans drivers. Sorry for the inconvenience.

• Windows 8 and Labview FPGA 2013

  I installed Labview 2013 including the suite of FPGA design on a host Windows 8 (x 64). I was surprised to see Windows 8 on supported OS list that I did not know until this day no further action taken design Xilinx support Windows 8.

  But as a question of fact, that he did not long until I hit:

  ERROR: Failure of Simulator: 861 - link design

  following this tutorial by clicking the syntax check (using one of the files provided with the tutorial VHDL). The error is clearly linked to a lack of compatibility of Windows 8 from XIlinx running under Tools. Is there a known workaround solution? Thank you.

  Unfortunately, you cannot compile the code on a Windows 8 FPGA Xilinx still not having this compatibility. The KnolwedgeBase article describes it. There is also a link in this article to another article that describes how to compile your code on a remote computer. This is the preferred method to compile when you have a Windows 8.

  http://digital.NI.com/public.nsf/allkb/8FDE6923DA3C069786257A36005C3EEF?OpenDocument

• LabVIEW FPGA: Deploy fpga with host program

  Hello people,

  I develop using a pxi-7831R (FPGA), 7.1 LabVIEW and Labview FPGA 1.1.0.  I wrote the fpga code and a host vi and they work well on my development computer.  However, I need to create an executable file and take it to my development computer to another computer (which also contains a pxi-7831R), and I don't know how to do it.

  Then I just build an executable from my host program and place the 'bit' fpga file in the same folder as the exe and copy it to the target computer, or what I need to somehow add the bit file to my build configuration?

  Thanks for any help!

  Chris

  Hi chassan,.

  In LabVIEW 8.x, the exe will offer the bitfile automatically.  I imagine it works similarly in LabVIEW 7, but it's probably best that manually regroup you the bitfile in your build options.

• problems with the project of example LabVIEW FPGA

  I'm trying to adapt the example project record on CompactRIO and LabVIEW FPGA Waveform Acquisition for my hardware, but can't seem to do things. I'm just following the instructions in the tutorial, but can not make sense out of section adapt this example to your hardware project, in particular, the instruction to "Drag FPGA Main.vi in the Project Explorer in the Open FPGA VI service window reference VI." Can someone explain on what is supposed to happen here? BTW, the target hardware that I'm doing this work on is a cRIO-9068 with some C series i/o modules.

  Finally, I came across the answer. For anyone else who may encounter this problem, the attached screenshot is worth a thousand words.

• HELP - FPGA SPARTAN 3E-100 CP132 WORKS WITH LABVIEW FPGA?

  HI EVERYONE, GET ON IM TRYING TO USE MY FPGA WITH LABVIEW, BUT I DO KNOW THAT IF ITS COMPATIBLE, I INSTALLED THE DRIVERS, MODULE FPGA AND LABVIEW 2012, IM USING WINDOWS 7 32 BIT, AND AFTER I COMPILED ITS SAYS:

  LabVIEW FPGA called another software component, and the component returned the following error:

  Error code:-310601

  NOR-COBS: Impossible to detect the communication cable.
  Check the communication cable is plugged into your computer and your target. Also, verify that the proper drivers are installed.

  Thank you.

  =)

  Hi dvaldez2.

  LabVIEW FPGA offers no support for any material to third parties, other than the 3rd Spartan XUP Starter Kit. These are probably the drivers you downloaded.

  http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

  However, this driver supports only the Starter Kit Board itself (http://www.digilentinc.com/Products/Detail.cfm?NavPath=2, 400, 790 & Prod = S3EBOARD). You may not use the driver with any other Xilinx FPGAS.

  I hope this helps.

• Simulate the sine wave using LabVIEW FPGA with NOR-myRIO and display in real time

  Hello

  I'm relatively new to LabVIEW FPGA. I am trying to test (and later apply) controllers high speed on myRIO.

  At this point, I'm trying to simulate the sine wave from 1 to 10 kHz using Sinewave generator VI express. I also intend to display the sine wave on the time real (RT) using FIFO. However, I had a bit of trouble to understaing various synchronization parameters.

  1. how to encode information about the sampling frequency generating sine wave? (The side FPGA vi requires only the frequency of the signal and possibly phase and does not rate update lines)

  2. how to estimate the number of items in a FIFO? (that is, the relationship between the rate of updates to loop (RT), the signal frequency, sampling frequency and the number of items in the FIFO)

  It would be great if we could share a very simple program (side host and target) that did something similar.

  Thank you

  MILIN

  Milot,

  I think the problem is the type of data in your FIFO. Your FIFO is configured to use a data type of I16. The problem is the number, it displays only ever will be-1, 0 or 1. To resolve this problem, you must send the sine wave as a fixed point data and convert it to a double on the side of the RT. This should significantly improve your resolution.

• Zip file and iso LabVIEW FPGA Xilinx tools 12.4 Module is broken

  I downloaded the two zip file of LabVIEW FPGA Module Xilinx tools 12.4 and iso image file three times to make sure that both files are broken and can not be installed!

  

  The size of the file is so large about 3g. It would be better to double-check before you download on the Web site.

  -Very well,.

  The download is complete and the standard Windows Extraction tool worked, WinRAR worked and 7Zip worked (and no, I don't know why, I installed all). I did download a wireless network that does not have direct access to our internal servers, it should therefore be a test valid. If the link I provided above was not that you used (probably isn't, because it is not an ISO option), could you please provide me with a link to the page that you used so that I can test and repair? In the meantime, the link above should work for you.

• LabVIEW FPGA and real-time communication module

  Hi all

  I created a small program in labview FPGA which gets continually distance from the HC - SR04 ultrasonic sensor. The rest of the robot program is written in the time module real Labview. Is it possible that the distance calculated by FPGA module to read in time real module.

  I used the FPGA just because there micro-deuxieme counter, which helps me get the distance from the ultrasonic sensor.

  Thanks in advance.

  There are many ways this can be done, according to your needs.

  See the help article transfer of data between the FPGA and host (Module FPGA) for a breakdown of each method.

• cRIO-9073 not appearing is not in devices and Labview 2009 targets

  In MAX, I show the following: a cRIO-9073 with NOR-RIO 3.0.0 installed. My system software has NEITHER-RIO 3.0. In LabView 2009, when I try and add the cRIO to my project in LabView 2009 in New-> targets and devices, I don't have a list in time real CompactRIO and my cRIO does not appear. I tried to add manually with its IP address, but it does not work either. I've updated the cRIO to LabView real-time 9.0 software.

  Is there other software that I need to update on the cRIO so that it is visible in LabView 2009? Do I need a new version of NOR-RIO?

  Thanks for any help.

  Todd

  I upgraded from NEITHER RIO NOR-RIO 3.2.1 3.0 and LabView 2009 seems happy.

  See you soon,.

  Todd

• Agilent driver causes LabVIEW jump and stop

  I started using AG6000A for LabVIEW driver. It seems to work fine until I do a 'Text' search and only on specific drivers. When I search on the 'acquire several example waveforms' for any text, the LabVIEW application finishes suddenly causing a loss in any work that is done. Does anyone else have this problem?

  I use LV 8.5 on a 32-bit operating system Windows XP.

  Thank you.

  Michael

  The driver, I found at http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=0D3F5F0998FE61CAE0440003BA7CCD... and I chose the version 8.0. However, I also found this driver:

  http://sine.NI.com/apps/UTF8/niid_web_display.download_page?p_id_guid=1E5E6D70FCA569A3E0440003BA7CCD... and I chose the version 8.2.

  I downloaded the 2nd driver and had no problem and them I have download the driver original and still had no problem. All is well now. Something must have happened when I added the driver in the folder instr.lib of LabVIEW. Anyway, sorry to bother.

  Michael

• NOR-Fieldpoint supported in Windows 7 and LabView 8.6

  We have a 'classic' with an ethernet controller FieldPoint system. We want to be able to read/write from/to the FieldPoint network using a computer with LabView 8.6 and Windows 7. NOR-FieldPoint is supported in LabView 8.6 and Windows 7?

  Kind regards

  Nate

  Hi natewkidd,

  I feel like some confusion between the operating systems running on a development computer (as Windows 7) and real-time operating systems that run on our real time (such as the PS-2000) controllers. I will do my best to clear up this confusion first answering your questions.

  (1) what is the difference between 2009 LabView real-time and LabView 2009?

  LabVIEW Real-time 2009 is actually a software officially known as 2009 LabVIEW Real-time which is installed after the LabVIEW 2009 development software to allow the user to develop and deploy applications in real time on targets in real time as your PS-2000. You can consider the LabVIEW Real-time 2009 almost as a plug-in for LabVIEW 2009 deployment and development of real-time applications.

  (2) if I have a PS-2000 on the ethernet network and to use a computer that is running Windows 7 and LabView 2009 for record and display data, will I still be able to communicate with the network FieldPoint screws write FieldPoint to my Windows 7 computer?

  If you go just to use the PS-2000 as a network module (NOT to deploy a real-time application to run on the PS 2000 itself), you should be able to communicate with him using just the read/write FieldPoint screw on your Windows 7 with LabVIEW 2009 machine and the driver NOR-FieldPoint 6.0.5. In this case, you actually do not need the Module Time since you do not deploy the application to the target in real time.

  About the PS-2000 unsupported beyond LabVIEW 8.5.1, is because the controller's memory is not large enough to hold the software that is installed on the controller with LabVIEW 8.6.x Module real-time and LabVIEW Real-time Module 2009. For more information on this, you can check this knowledge base article.

  I hope it's useful! Let me know if you have any other questions.

  Thanks for choosing National instruments.

  Aaron Peña

  National Instruments

  Technical sales engineer

  http://www.NI.com/support