Neighboring relationship DMVPN heartbeat problem

Similar Questions

• The scale and the relationship between the problem of points

  I had a few problems with setting the scale of the objects and their appearance before and after the scaling.

  The relationship between the points change when I change things, and it's a little embarrassing.

  Before that I put across that circle with an arrow, it looked like this:

  

  Then after that I put across it, the lines on the arrow were not in place:

  

  It happens very often when I am scaling of paths in illustrator. Is there something I can do to prevent it? Often I make things evolve upwards or downwards and it is a little painful when I know I'm going to screw up the path.

  

  

  Go to the drop down at the top right of the Panel processing and disable "Align new objects to the pixel grid."

  Edit: If you select 'Web' in the new Document dialog box, "Align new objects of pixel grid" is enabled by default, at the bottom of the box. You can choose to disable it there before OK-ing the creation of the document.

• DMVPN WILL ACCESS LIST

  Hi, guys

  Could you please help me with this matter?

  When you configure the DMVPN talk-to-spoke with several hubs (GRE IPSEC EIGRP) talked about what traffic should be allowed on the external physical interface on a router?

  !

  IP access-list еxtended CRYPTO-ONLY

  license to esp [IPSEC peers Reomote] [IPSEC peer Local]

  permit of eq isakmp udp [IPSEC peers Reomote] [IPSEC peer Local]

  allow accord [IPSEC peers Reomote] [IPSEC peer Local]

  !

  interface FastEthernet

  IP access-group CRYPTO ONLY in

  !

  If I delete the last line of the access list, where the "free WILL" is permitted, the router never built EIGRP neighbor relationships. If this line should be present? If so, does any not encrypted GRE traffic will come out?

  Thanks in advance,

  Mladen

  Hey Mladen,

  The access list bound to the external interface is checked twice IE before and after decryption. This is why you must allow packets will clear also.

  HTH

  Sangaré

  pls rate helpful messages

• BATTERY LENOVO IDEAPAD Z510 PROBLEM

  I bought Z510 a year back, in this short time I am facing battery problem. Battery won't charge and the system to keep plugged in a State with each use.

  I'm a home user and use the laptop for a limited time. I don't understand why lenova did not provide a removable battery that can be changed by the user only.

  Now new battery is not available on the market, also that Lenova simply made it their responsibility saying laptop in not less than warranty.

  I ask Lenovo go to analysis of root causes of this problem that hundreds of people face the same problem in this model.

  Hope Lenovo would provide some software to assist the problem or at least to give the details of the service provider where the batteries can be repaired or replaced.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Z510 Problem Batery

  Dear Sir

  I have a problem with the battery on my laptop (Lenovo Z510). IF I work without the power cable in my laptop notebook unexpectedly closes without any warning of low battery. When I put that laptop power cable works fine and begins to charge the battery.
  Is my default battery or what could be the problem?

  Jeffrey

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Problem with the Lenovo Z510 battery indicator

  I have an old Ideapad of one year z510. Last week, the battery indicator began to stuck on 100%. So not connected, he stops suddenly without notifying me with 10% and 7% remaining notification. I tried to uninstall the Microsoft ACPI control method battery compatible from the Device Manager but no change... Anyone has an idea what should I do otherwise.

  Thank you
  Ahmed

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Battery Lenovo Z510 problem

  Greetings! I have a Lenovo Z510 8 GB Ram, Core i7, 1 TB hdd, I bought less than a year ago. Off late I've known major battery issues. He started with the laptop stopping randomly without warning, even if there is a life on the left, for example. PCT of 90 or more. This worsened when the laptop did not start at all, until I plugged in the charger. The only way I can now exploit the laptop is connecting to the charger, but again, the battery remains at 0 of the pct, does not load. The battery light continues to flash red, also, I used a BatteryInfoView application to analyze it, and it still says battery reached 83 percent of its original capacity, however, I get a message every time at startup saying the battery is low and needs to be replaced. What can I do about it? Thank you.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Battery Z510 problem, battery is 0% all the time

  
  

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Battery IdeaPad Z510 problem

  Hello everyone,

  Last week, I installed 10 64-bit Windows on my laptop (Ideapad z510).

  The first time my laptop is suddenly turned off, but the battery was far from empty according to windows. When I tried to start again it appeared that the battery was empty.

  I noticed that the percentage that windows reports is incorrect. After 2 hours without power my battery was normally about 30%. Now, it was still above 90%.

  I have installed power manager and I use the balanced profile.

  Does anyone have an idea what could be the problem?

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• [Z510] Problems with the battery not charging

  I have ideapad z510 for almost a year. and now my unit still shows that it is at 0% battery. and she indicates that she battery level does not increase. and for this reason I could not use my unit when it is not plugged. What should I do about it?

  Comment to Moderator: New thread is created. The topic is edited to include the model.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Z510: Battery problem

  I have lenovo ideapad z510 1 last year and at this time no problem, but 4 days battery that is the question

  When I plugged in the charger it stuck at 1% and all of a sudden after about 20 minutes it says 100% battery and when I remove the charger, the falls to 0% all of a sudden.

  Moderator Note: model added to the subject line.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Nearby EIGRP falls on GRE tunnel

  I have several users working at home with a router 871 a 2811 access in our offices. While most of these connections works without any problem, I have a few sites that continue to drop the EIGRP neighbor. Here is a sample of the log file

  * Dec 17 06:32:48: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

  * Dec 17 06:41:58: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

  * Dec 17 06:42:03: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

  * Dec 17 06:43:41: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

  * Dec 17 06:43:46: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

  * Dec 17 06:49:30: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is falling: Farewell Interface received

  * Dec 17 06:49:33: % DUAL-5-NBRCHANGE: 10 IP-EIGRP (0): neighbor 172.29.1.49 (Tunnel1) is on the rise: new adjacency

  Does anyone have any ideas as to what may cause this problem?

  Rick

  Run us EIGRP GRE/IPSec tunnels to many remote routers. We have seen this problem of instability of EIGRP neighbor, more in some areas and less in others. Often one side removes the neighbor relationship and sends a 'goodby' neighbor. I guess it must if with packet loss drop some of the EIGRP Hello messages. We found that, by increasing the EIGRP timers, we reduced the frequency with which we see the problem (we use 15 and 45 rather than the value default 5 and 15).

  HTH

  Rick

• 3000 VPN concentrator using ospf md5 authentication failed

  Hi all

  I just tested ospf with a 3005 VPN connected with a cisco router using ospf md5 authentication, but fail. Cisco router, I can see neighbouring State ospf is "INIT", but can not see any connection VPN 3005, physical connection is good, ping can be reached between them. I tried the command "ip ospf authentication message-digest & ip ospf authentication-key ' and"ip ospf message-digest-key"command in the router the password is the same in both sides and the md5 id has been set. But when I use simple authentication or disable authentication that the neighbor relationship can ride. Any body met this case before? Thank you!

  Best regards

  Teru Lei

  Hello

  This is a known bug, I also met this before: CSCef38044

  It is not possible to accumulate OSPF with newer versions of IOS, on which they'RE ability is enabled using MD5 hash neighborship. They'RE capa is activated somewhere of 12.2 T. This behavior can be found on CVPN 4.1.5 and above whose 4.7 also.

  I tested it with several IOS and OS CVPN - same result. The symptom: router ospf neighborship remains in the State INIT/DROTHER.

  Workaround is to configure the router:

  router ospf 1

  No they're ability

  This will solve your problem.

  Attila Suba

• VCSC INACCESSIBLE DESTINATION

  ALCON,

  I have a neighbor relationship upward with a site and the site remote is able to dial in our bridge via IP and alias.  I am able to dial up a point to end of line remote via alias.

  Problem is when the line trys remote dial in one end on my end which is recorded in the cluster, it does not connect.

  Don't have not even get a ring.

  The system is functional at 100%.  I can dial the far end via alias no problem...

  I checked the search history and see that the system is trying to connect and an error message "Destination unreachable"? So it appears the call makes my VCS cluster but will route to the endpoint?

  Any ideas.

  I can make other calls in two ways by nearby with other sites of relationship alias.

  Thank you.

  Chet Cronin
  801-815-3539 (USA)
  + 9379 601 - 3954 (Afghanistan)

  Hello

  If your VCS is running in Direct mode, theoretically, you don't need to create a rule to search to any IP address.

  Tell me something, have you tried to call this end point of 1000 MXP numbering by IP address from a local endpoint registered to the same local VCS? It work?

  Also, you can try temporarily disabling the search rule 'any address IP"and try to call again to the remote site? You can post the details of the history of the research?

  In addition, if you try to call this end point the remote site MXP component number instead of the IP address, it works? Can you confirm?

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Equium MX40-103 screens towers but does not power down

  I have the above model. The laptop works well except for the fact that the screen turns off but is still running.

  This can happen in 10 minutes or after hours, I can't find one any relationship with the problem.
  However, the laptop will beep once for a longer time, then twice for a shorter duration, then the screen turns off.

  This occurs when the computer is loaded up, is not when loading windows. Thanks for helping me

  Hello

  Have you tried updating the graphics card driver?
  What about your BIOS version? If the latest version is available on the Toshiba page that you could try to update. But be careful! Don't forget to use the good BIOS and use the right update procedure

  Anyway. I read somewhere on similar problems and it seems to be linked to the main Exchange of bad parameter between LCD and PCB.
  This can be caused by a damaged ROM chip on the LCD screen.
  But to be 100% sure, you will need to contact the service point.