NEM tudok nyomtatni
A pc felismerte a nyomtatot, kiirta: KonicaMinolta Magicolor 2350.
Hello
See this page to select your language:
http://support.Microsoft.com/common/international.aspx
====================================
Or sorry that it is area English.
On the top of this page of answers (English) v -click and set your language.
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
Tags: Windows
Similar Questions
-
NI Stepper drive is compatible with NEMA 11 both NEMA 42 engines step by step?
I have an NI PXI-7350(Motion Controller), a UMI7774 or (Universal Interface), and a (Stepper Drive) P70530 NOR and tried to connect the new NEMA 11 stepper motor actuator linear Hayden Kirk and kept getting a constant red flashing light on the driver. I then plugged my new actuator linear motor NEMA 23 stepper Hayden Kirk and the pilot got the green light ahead go and it worked fine. I consulted the manual and saw that the driver was compatible NEMA 17-34 Steps. I tried the third affecting both the NEMA 11, nothing helps. Does anyone know a player NI Stepper, which is compatible with my UMI and motion controller and is also compatible with a NEMA 11 and NEMA 42 (another engine step by step I need) stepper motors?
Hello T.I.
It is true that our engine controls step by step only have been evaluated and tested for engines not to not NEMA 17, 23 and 34 size. I personally haven't seen or worked with readers with the NEMA 11 or 42 engines step by step, but given that NEMA standards are only a standard size, as long as your engines are under tension, power and plug for your engines to P7000 series inductance, walk, then they should be able to work.
-
Problem:
After my order of motor NEMA 23 stepper motor driver P70360 connection and use of MAX to start and stop the axis, the engine got hot and stayed hot (I turned to MAX then went to lunch and the engine was still warm). Is the engine that is supposed to run hot? Is there a switch turn (in addition to the driver off power), I'm suppose to use? My setup is false?
Installation program:
PXI-7334 connected to UMI-7774 cable of the IO request
UMI-7774 connected to the driver not to not P70360 using control cable
P70360 Stepper driver connected to NEMA 23 (T21NRLC) using Orange (A)-, black (A), yellow (B)-, red (B)
NEMA 23 is powered by the power supply 120 v AC
P70360 Stepper driver is set using DIP switches (I tried to use the P7000 software tool that came with it, but he never found the driver):
S1: 1
S2-1: stop
S2-2: on
S2-3: on
S2-4: on
S2-5: Off
S2-6: Off
S2-7: Off
S2-8: stop
S2-9: Off
S2-10: on
S2-11: on
S2-9: Off
Hello
First of all, thank you for post step by step detailed engines and Yes run hot. Hot enough that you can't hold it in your hand for a long time. It's normal. The way to keep cool when not in use is by removing the power of the engine (by disabling the drive that you mentioned).
-
NEMA OUTDOOR FOR CISCO AP 3702
Hello!
One of my clients want to settle and NEMA (enclosure) for cisco AP 3702 OUTDOOR, but I can´t find the part number to order it!
Can someone tell me if there is a reference number? I found http://www.terra-wave.com/cisco-3702e/http :// www.terra-wave.com/cisco-37...
but obviously not cisco.
So I guess the question is: cisco cell of this Articles? If yes where can I find part numbers?
Thanks in advance
You're right, Cisco does not. In this document, they recommend one of the following providers:
http://www.Cisco.com/c/en/us/TD/docs/wireless/technology/apdeploy/8-0/Cisco_Aironet_3700AP.html
Third-party sources for the envelopes of NEMA type include:
-
EZVPN nem - Internet access mode
Hello
I have a router cisco 881 and an asa 5520 SW 8.4
I configured EZVPN NEM mode between the router ASA and 881. However the 881 can access network resources on the inside interface of the ASA, where it ends. However the site using the 881 cannot access the internet. I know that I could configure split tunnel and the site would use only the tunnel for our internal network (10.0.0.0). However, I want this site to our ASA allows access to the internet so that the restrictions will apply to this site too. I apologize in advance if I have not provided enough information.
Router config 881 is lower, ASA config is too big to post, but if you tell me what exactly you want I post, I will;
no ip domain search
"yourdomain.com" of the IP domain name
IP cef
No ipv6 cef
!
license udi pid CISCO881-K9 sn FCZ17219082
!
username secret privilege 15 netadmin 4 N2rcMRAZjsOjF7Kp/KUkH4cfBtBYp.1Cc.V8E0utmSI
!
Crypto ipsec client ezvpn EZVPN
connect auto
Group TG_EZVPN key ourkey
network extension mode
peer FIREWALL IP
username password user password
xauth userid local mode
!
!
!
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
Description * Interface Outside *.
DHCP IP address
automatic duplex
automatic speed
Crypto ipsec client ezvpn EZVPN
!
interface Vlan1
Description * EZVPN inside *.
IP 172.16.217.1 255.255.255.0
IP helper 10.1.4.60
IP helper 10.1.4.61
IP tcp adjust-mss 1452
Crypto ipsec client ezvpn EZVPN inside
!
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP route 0.0.0.0 0.0.0.0 dhcp
Hello
As long as the traffic to any other network other than the network to remote sites runs through the VPN connection, then the more typical than the ASA things central may be missing are the following
permit same-security-traffic intra-interface
If this configuration is already currently in use can be controlled with
See the race same-security-traffic
The above arrangement allows the ASA transmitting a packet entering an interface through this same interface, that it came at the start. Without this parameter, it is not impossible.
Then you will naturally NAT configurations for users of the Remote LAN connections
If we were to use NAT Auto / network object NAT (since I don't know how you have built the base dynamic PAT to your central site ASA) configuration might look something like this
network of the REMOTE-SITE-PAT object
172.16.217.0 subnet 255.255.255.0
dynamic NAT interface (outdoors, outdoor)
The above should provide the dynamic PAT to the interface ' outside ' of the ASA central when the hosts are connected to the Internet.
Given that the NEM Mode VPN is probably connected right now that you can test what would happen to a related Internet packet across the VPN connection (even before changing the settings above)
entry Packet-trace out tcp 172.16.217.100 12345 8.8.8.8 80
That should tell what happens to the content of the package. If you are missing the first order, I suggest you the output of "packet - trace" will be very short and should see a DECLINE Phase very quickly
-Jouni
-
Management access to an ASA5505 via connection NEM
Hello
I work with a configuration ASA5505 NEM.
Everything works well except the access to content the device across the tunnel. From the ASA local network I can access the device via HTTPS, Telnet and SSH, but it does not work in France via the tunnel. I am running version 7.2 (4).
No idea what I am doing wrong?
Thank you
There is no attachment in your post...
You can check out asa have access to the administration:
See the race | Management Inc.
If no output from the top Configure asa with stated below, then try to access to asa by tunnel.
management-access inside
PLS note any useful message
Rgds
Jorge
-
Audio intermittent one-way via VPN NEM
I have a user who uses an ASA 5505 in NEM to have access to his laptop and home IP Cisco phone. The ASA 5505 establishes a tunnel to an ASA 5510, which is connected and speaking of EIGRP to our main switch. Off the main switch, we have our CCM cluster.
The problem occurs during the first call, after a long period of no appeal. After, if happening during the first call, he or she can continue to make calls without the question. I that it was a matter of time-out, but its ASA configuration is exactly the same. In addition, it uses the same group policy, the tunnel-group etc. that everyone with the same configuration.
When the problem occurs, it can not hear the other party but they can hear him/herself.
This problem occurs without worrying whether or not it has a PC behind the phone.
External and internal calls are affected.
I am aware that more one-audio questions are questions of RTP connectivity between two end points. I see clearly in the routing table of all our routers, that the path to the subnet his phone is on has not changed for days, and she got the question within this period.
I'm looking for a good place to begin troubleshooting that doesn't require me to a pcap. If all else fails, I'll do a pcap, but trying to be what some judicious with my time.
I am certainly able to accept that maybe it's his router at home since it is one of the unique things only on access at its facilities, compared to other people the 20 I only did this.
Thanks in advance.
Cisco IP Phone 7941
CCM 7.1.5.32900 - 2
ASA 5505 8.2 (5)
ASA 5510 8.2 (5)
Edit: Moved to the VPN
Hello
I suggest you ask if the number of packets increases during an ongoing call. (press on '?' twice).
Also, I think you asked this question in wrong discussion group, it must be under the lead of security instead of the voice.
-
Traffic no routing between remotes using ezVPN with NEM
I scoured the forums for a while now, looking for ways to solve this one but just can't find anything that helps. I ezVPN configured on an ASA 5520 for my server with 5505 s like my clients at several remote sites. The tunnels go up without a problem and I can hit what I need on both sides of the tunnel, but I'm not able to go to another remote network from a remote network. Traffic shuts down the tunnel on the 5505, but on the 5520 I don't see is a bunch of scrolling tear down messages. Any thoughts would be greatly appreciated.
Side hub
interface GigabitEthernet0/0
nameif Inside_Network
security-level 100
the IP 10.0.0.1 255.255.255.252
!
interface GigabitEthernet0/3
nameif Outside_Network
security-level 0
IP 192.168.32.8 255.255.255.0
!
permit same-security-traffic inter-interface
!
Router eigrp 10
Network 10.0.0.0 255.255.255.0
redistribute static
!
Crypto ipsec transform-set ikev1 my - set esp-aes-256 esp-sha-hmac
Crypto-map dynamic ezvpn 30 set transform-set my - set ikev1
Crypto-map dynamic ezvpn 30 the value reverse-road
map outside_map 65535-isakmp ipsec crypto dynamic ezvpn
outside_map Outside_Network crypto map interface
Crypto ikev1 enable Outside_Network
IKEv1 crypto policy 10
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
!
internal VPN_GP group policy
VPN_GP group policy attributes
VPN-idle-timeout no
allow to NEM
!
username password encrypted Wj0QXCAEhK12A5Sp privilege 0 vpnuser
!
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
Group Policy - by default-JEOD_VPN_GP
Group-tunnel VPN ipsec-attributes
IKEv1 pre-shared-key *.
Remote side - more than necessary here
vpnclient Server 192.168.32.8
vpnclient mode network-extension-mode
vpnclient vpngroup VPN password *.
vpnclient nickname vpnuser password *.
vpnclient enable
EzVPN remote clients can connect to the Headend ASA5520 but cannot communicate with each other. Is it correct to understanding?
All guests of EzVPN are end on a different external physical interface of the ASA? If not, we will have to allow intra-interface traffic too with inter-UI that is same-security-traffic permit intra-UI.
-
Voce nao tem permissao para criar nem driver este conteudo
Voce nao tem permissao para criar nem driver este conteudo
Is this a question? Is this related to the reader? Details, please.
-
NAO estou access download o adobe creative had cloud o programa false, agora I bought a licença, I can not desistalar o false nem download o pago, o devo fazer
Hello
I guess that you receive an error for the trial creative cloud.
You can download the installer for Creative Cloud from here:
Creative cloud help | Creative cloud desktop.For the error of the trial;
First of all, disconnect, then back into creative cloud, using adobe id to pay for your subscription.
https://helpx.Adobe.com/creative-cloud/help/sign-in-out-activate-apps.html
Then, if you launch any product of CC 2015 and the pop up still shows a trial message window, please check this link for the resolution:
https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html
-
NEM indul el AUTOMATIKUSAN has LETÖLTÉS, MIERT?
Indul el NEM a verzio zombies automatikus Trial. Miert? Azonosito, jelszo megadva, visszaigazolas is rendben.
Try to download from
-
Instalei o Adobe Illustrator trial no meu PC, mas quando EU o Ahmed nao don't demora nem dez segundos ele date alone
-
OLA, meu celular sem sinal was para receber e outra fazer uma hora para clover, so Wi - Fi works, me disseram o imei blocked, posso fazer o esta only?
Obrigado
ISSO e algo that tera aybody com voce sua operadora - UO, is possible, o suporte original no telefone. Desautorizando um telefone nao e um processo Apple - e geralmente iniciada pelo suporte original. Além disso, como EU o entendo - uma vez that um device esta na lista negra em uma region as nao pode ser reativado
Tudo bom!
-
I can not add making conta email Gmail e nem os synchronise to
BOM dia
Proceed as Estou tentando add minha conta email Gmail e os is, ao selecionar a conta Google appears a mensagem abaixo:
Conexao Insegura
Falha ao verificar o certificado do servidor. ISTO pode ser por causa da sua configuracao of rede or seus proxy Clamp back.
Obrigado
Boa noite,
Estou tendo o mesmo problema conexao insegura ao gravar uma nova conta do gmail. Voce ja was any response?
ATT,
Felipe
-
780068-01 NI NEMA 17 Stepper Motor double tree - coders?
Maybe you are looking for
-
Hi guys,. I need help on a question that really puzzle me. After I tried to do a bios update to the last version (February, 2012), in windows 7, I got an error message stating that I didn't have permission to do the update. Since then, the fan starts
-
Need to go to bios compaq mini cq10 130
Hello can help me, I have change my cmos battery and now asking me bios password password check failed fatal error system stopped CNU00550CJ Thanqs
-
Failed to read my hotmail messages - all messages displayed by the sender and the subject however nothing will open when licked c on... of ideas why?
-
I would like to know if I can attach my Webcam 3100 extension and if so, how? Will this affect the image quality or the sound? Thank you.
-
Can not get the display in normal mode = safe mode only. __
System Restore does not work. I got the no display problem resolved earlier and had cover down on laptop set to "do nothing". I closed it and reopen, I was unable to get a display in normal mode. I get the appropriate two sounds to start, but then