Network location using cmd of the tree card

Similar Questions

• Network discovery, file sharing settings keep changing by itself and Alltel to set the network location continues to ask the wireless device

  former title: network location settings. Discovery of NW. File sharing. public folder sharing. AVG 9.0 'tools' and network connections.

  My Alltel Wireless device again set the network location. And continues to change my network settings for the discovery of NW to:, as well as file sharing for: file public and sharing: read-only.  I have AVG Security 9.0 and under 'tools' and connections network shows several svchost with States reading service connections listening and unknown. I don't want no access to my computer and cannot find any computer consultants who can get this to stop. What can I do?

  Hello
   
  1. the options apply automatically on?
  2. have you made changes on the computer recently?
  3. have you installed any Alltel Wireless application to manage network connections?
  4. What is the current network location type on? Is it home, work or public?
  Network discovery and file sharing settings depend on the network location. For examle, if you set the network as a public location it turn on file sharing.  So I would ask you to turn all the parameters and then choose the type of network and check if the parameters change again.
  
  Method 1.
  I recommend you to check if the problem exists in clean boot. May be a third party application is causing these changes.
  See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.
   
  Method 2.
  Also check the settings under tools in AVG security suite. You may need to check with the help of AVG on it.
  Or you can disable the antivirus software and check if that causes this behavior.
  Temporarily disable the security software installed on the computer and check if the problem persists.
  Disable the anti-virus software
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
  
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Issue of APEX 5.0: symbol of continuous loading when using parts of the tree with Mobile Applications

  I use a use of a region of the tree Mobile Application. The tree implementation is defined on Tree APEX.

  When I run the Application, I get a symbol of continuous loading.

  When I use the same SQL, region and implementation in a desktop app it works fine.

  I can't get it working on a Mobile Application with the implementation of jsTree.

  bug?

  Hi Matt,

  The area of the tree is not supported for mobile pages. If you use the new page Wizard to create a mobile page, you will see that it is not established that the area of the tree. It only appears if you decide to display unsupported. What seems like a bug, it's that the tree is displayed in the Gallery of areas of the page designer.

  The implementation of the tree of the APEX (widget.treeView.js) is a jQuery UI widget. Even if the core of widget in jQuery UI and jQuery mobile are essentially the same tree view widget has additional dependencies such as $. UI.mouse. the reason why the old jsTree can work at least a little, is that it is a jQuery plugin not a jQuery UI plugin (if I remember correctly).

  I also think that on a small phone size screen that a tree would not work so well.

  Kind regards

  -John

• correct the address to the network location

  I have two Windows PC. The two are running the latest versions of Windows 7 Home Premium.

  It runs on a HP laptop, the other is a virtual PC running on VMware fusion running on Macintosh, but cannot remedy by the same method.

  The HP one I can address network location use - (Public (MYBOOKWORLD (My Book World Edition Network Storage)).

  The Virtual PC, I can only answer same network place - (Public (192.168.1.3 (My Book World Edition Network Storage)).)

  On the Virtual PC when I try to 'Add network location' I get error "the folder you entered is not valid. Try another chosen. »

  As I network set to DHCP dynamic drives, I can lose access to one or more information on virtual PC.

  How can I change so that both computers work the same?

  Hello

   

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

   

  Hope this information helps.

• A wi - fi network reset to "out of the box.

  Hello

  Sorry to ask what may be a very basic question, but how do you define a wireless router - more WiFi settings of your laptop - back to the way they were when they came out the box? In other words, I want wireless and portable routers that I forget they know so that I can set up my wireless network again as if I put for the first time.

  The reason is a little involved, but for the most part, I had a set up wi - fi network and launched from a Terminal Airport Express and it worked very well. During the holidays I then bought an Airport Extreme because I wanted something a little better for my base unit and then I wanted to use the Express as an Extender. How I wanted to now, I had not tinkered with something that was not broken, as the addition of the extreme for the network was not as simple as I was expecting and my wi - fi network everything seems to go wrong, like my internet connection. I had someone to configure two routers (understand I can I have messed up a setting when I was trying to implement) but still no luck - he would work for a bit and then my internet would just go down. Using Airport utility, showed that routers and internet will run for a few seconds and then would stop and I would lose the connection.

  I work and live on a college campus for the internet at home is powered by an ethernet into the wall jack, just as you would in an office. Through contact the COMPUTING helpdesk, they managed to tell me (although partly because of techno speak and a little bit of a language barrier that English isn't the first language here) I got away from. What I could gather was something like the two routers SSID must be different because they were "beating" and this caused the network to automatically shut down at home? Unfortunately they treat only to provide internet service home and cannot help with the problems of wi - fi.

  I am pursuing other means to help (we are a University of science and technology research, after all!), but something I thought was if I could just reset routers and WiFi my laptop 'memory' of the network and start over as if I was there for the first time. I don't want to plug the router and it says something like "this was part of the XX network."

  Anyone know how?

  Thank you very much

  To configure your router from Apple to its "out-of-the-box" configuration, you must perform a ' default ' reset on this subject.

  For the laptop, if it's a Mac, then you will need to follow these steps for "erase it."

  Start with the first steps (1 - 1). If that is not accomplish what you're looking for, go to step 2.

  1a. remove preferred networks

  System Preferences > network > Wi - Fi > advanced > tab Wi - Fi

  Under "Preferred networks", delete the networks you use regularly in the list.

  1B. Airport deleted keychain entries

  Launch the application "Keychain Access", located in Applications/Utilities.

  In the windows on the left side: Select login for keychains and "All items" category.

  Click on the 'Genre' filter at the top and search all "AirPort network password" entries... and remove them.

  1 c. Add Network favorite (s)

  System Preferences > network > Wi - Fi > advanced > tab Wi - Fi

  Add preferred networks using the button «+»

  Restart or disconnect you, then back in.

  2. move the System Configuration files

  (Note: you will need to restore your network connection settings.)

  Go to Macintosh HD/Library/Preferences

  Move the SystemConfiguration folder on the desktop.

  Restart your Mac. (Note: OS X will rebuild the folder & files that are now sitting on your desk in the library > location of preferences.) If this does not resolve the problem, you can move the folder back to its original location.)

• Recommendation for the DAQ card

  Hi guys, =)

  I m currently developing a project in a gas control, where I need Messure tempertures and be able to open and close a valve.

  My implementation are 4 termocouples and 4 relays to turn off the valves and...

  I was hoping if someone could help me choose a card of data acquisition for two things. where she has 4 analog for

  thermocouples and 4 digital (5v) output 4 relay. and be able to use them on the same card DAQ, USB PCI o preferably. or

  use a map of data acquisition for entry and one for exit.

  Thermocouples type K are...

  TNX in advance...

  Sincerely

  Luis Alonso

  Hi Luis,.

  How current are required by the relay? Is the combination of a cDAQ-9174and NI 9211 , NI 9401 sound like it might meet your needs? You can also focus on devices that have integrated relays, such as the NI 9481 or PCI-652 x.

  Brad

• Printer Officejet Pro 8620: officejet pro 8620 failure of the wireless card

  E-all-in-one printer Officejet Pro 8620 was strange for the past few weeks - the blue light would remain solid but nothing prints not the touch screen would not respond and it would be not closed when the power button was pressed.  Now, it has gotten worse - he sees not the wireless network (other devices work well) and prints a blank page to print the report.  I ran the printing and scanning Dr, but he did that tell me that the printer cannot detect the network.  I tried to reset to the default factory settings wireless, but it still does not detect the network.  I think that the wireless card is not (it is exactly one year and two weeks since I bought it).

  Is there a way to confirm my suspicions?  Is there anything else that might be causing these problems?  If so, how to replace the wireless card?  I worked with electronic equipment for years and I'm very comfortable, replacement of parts and components of computer devices.

  I did the factory reset and went through the installation procedure as directed.  The printer still can't find wireless network and print report still produces just a white sheet.

  I'll contact the HP Support

• try to install itune guard saying could not access network location %APPDATA%\protector.exe

  try to install itunes on win 7 whenever the State happens to need computer space he stops and says "could not access network location %AppData%" I tried the fixit for from microsoft and it keep saying that he can someon help me please

  Try this FixIt:

  http://support.Microsoft.com/kb/2258121

  This should fix the % AppData % question.

  André

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• U2414H DisplayPort 1.2 STD Set Up - monitors will not get video Signal from the graphics card during start or restart

  * What specific Dell monitor? 2 two U2414h monitors with MD214 - package of multi-monitor support
  * What specific model of computer, desktop/laptop? Workstation HP xw8400, Intel Quad Core Xeon CPU E 5335 @ 2.00 GHz, 4.00 GB of memory
  * What operating system? Windows 7 Professional 32-bit
  * Which video card? AMD over-pants V3900
  * Which ports are available for the video card? DisplayPort 1.2 STD, Dual-link DVI
  * Which video output from the video card port video on the port monitor do you use? Output Mini DisplayPort Display port in
  * What cable are you using to set the video card to the monitor? Adapter DisplayPort to MiniDispayPort - we came with every Dell monitor
  * You use the Dell supplied cable? Yes - two monitors

  * Press the Menu button of the monitor to open the OSD (On Screen Display). The bottom of the screen should display a resolution. This resolution should match the resolution of the default monitor. The two monitors: 1920 x 1080, 60 Hz

  * Brief description of the problem monitor? Monitors have been implemented following the instructions on page 25 of the Dell online manual to connect the monitor to function DP multi-flow (MST). DisplayPort cable is connected to V3900 output MiniDisplay port DisplayPort graphics card in the 1st U2414H; second DisplayPort cable is connected to the DisplayPort on 1 U2414H monitor output and MiniDisplayPort in the 2nd monitor U2414H. Dell U2414H drivers have been installed from the CD provided and both recognized by Windows. V3900 graphics card Driver is up to date with the EyeInfinity software. Source of input on both monitors the Mini Display Port value. Display settings on both monitors Display Port 1.2 value activate. Resolution of the screen on Windows 7 shows: (a) two separate Dell U2414H (mini Display Port) screens, with each resolution 1920 x 1080, multi (b) displays the value "to extend these displays. The two views work with Setup leading up to and acknowledged by the graphics card.

  Problem 1 - all the time - monitor power buttons are lit, the computer is turned on, then monitors lights don't - they show 'Power save mode' and then turns off. To hit the power button on the computer to shut down Windows. Only way to get these on monitors is unplug cords from the back of each monitor, wait a few minutes, plug in the power cord, start computer and then both monitors will start up and sign of windows to the screen will appear and monitors will work. Normal operations for a full day of work if you do not restart. If you need to restart during the day (like when you get a software update), the same thing happens. Start the computer to restart, but the monitors come back on not and remain dark. There is nothing wrong with the graphics card V3900. He is certified by AMD and DisplayPort.org to work in an environment of STD DisplayPort 1.2. I had previously two 215tws Samsung SyncMasters connected to each output V3900 Grahics card and they work very well in extended mode for years until a SyncMaster 215tw started shaking like crazy. A SyncMaster has been connected to the out display with a dongle and a DVI cable Port. The other SyncMaster was connected to the DVI output on the graphics card. So I decided to buy these two U2414Hs. Technical support Dell after many phone calls and e-mails finally advised me that there is a problem of "compatibility" between my computer and the U2414Hs and recommended that I return the monitors. On the web site of the U2414H AMD has not been certified by AMD to work in a DisplayPort 1.2 STD Set Up. Other former Dell monitors are certified by AMD to work in the Display Port 1.2 Setup. DisplayPort.org lists the U2414H to work with Display Port (it does not say that it will work in a DisplayPort 1.2 Set Up).

  Problem 2 - shift perceptible in the entrance of Microsoft Blue Tooth keyboard and mouse and PS2 Keyboard and mouse. All the drivers are up to date. When you type a phrase, it takes a few moments for the text displayed on the screen using a keyboard. Both the mouse connected and the Bluetooth mouse are unresponsive sporadically for a few moments until they finally react. It happens regularly during the day. The monitors provide excellent clarity when you work. The stand is ideal for office property. Before these monitors are returned if no one knows what causes these two problems and does anyone have a solution? Should I stop using the Display Port 1.2 and hang them using HDMI with active dongles? If I have to return these two U2414Hs, I considered the 2 two U2413s. Someone at - it all opinions on the last U2413s from Dell? I have read some real problems with ghosting that I just haven't the time for more. The remanence correction in the models of U2413 sold in 2014? There are very few monitors on the market with Display Port in and out to the back to support DisplayPort 1.2 STD Transport.

  Thanks for any input.

  I had to remove my VGA HDMI DV card and now the DP (display port) works very well. Don't need to use a HDMI cable. Display Port 1.1 is reported as the problem in order to remove the card solves this problem.

• Optimization of the tree

  Hi all!
  
  I have an accountant named form.
  
  I'm doing this form using models of the tree.
  
  just started this form takes too long to open because table of COA has 2500 documents, it takes too long to load.
  
  kindly tell me the right way to solve this problem.
  
  
  I use the following question to fill the tree at startup:
  
  SELECT
  1,
  LEV,
  ' ' || ACCOUNT_NO | ' -> ' || ACCOUNT_NAME,
  DECODE (IS_TRANSACTIONAL, 'IT, 'OPEN',' YOU, 'NEW'),
  TO_CHAR (ACCOUNT_NO)
  Of
  ACCOUNTS_CHART
  CONNECT
  PREREQUISITE ACCOUNT_NO = PARENT_ACCOUNT_NO
  AND ID_COMP =: GLOBAL.COMP_ID
  START BY
  PARENT_ACCOUNT_NO IS NULL
  AND ID_COMP =: GLOBAL.COMP_ID
  ID_COMP ORDER, ACCOUNT_NO

  That's why andreas this code postal

  Big trees - using the population of partial tree

  http://Andreas.Weiden.ORCL.over-blog.de/article-29307730.html

  Thanks to andreas

  Kind regards

  Abdetu...

• My computer is on a network, but Windows 7 (Pro x 64) shows that it is not. Cannot change network location to home. Cannot use the homegroup.

  I'm putting my network (with homegroup) home, but when I go into control panel > network and Internet > homegroup, it says:

  "This computer cannot connect to a homegroup." Then,

  "To create or join a homegroup, network location of your computer must be on home."

  Okay so. I go to network and sharing Center and click on "connect to a network" and I get a box in the lower right corner that says "no connection available.

  I find that strange, because when I click on 'My Computer', I see in the left pane all the computers in my house under 'Network'... so I'm in network... but I'm not?

  It is a problem because until I am able to add this computer, I am unable to share the data on this computer and it is my office alone AND the pc is connected to my router.

  I can not access my storage drive. I can't stream media.

  All opinions are appreciated. Thank you.

  Hello

  Check the Device Manager for the entry of valid card of the wire.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a Local Area Connection icon/entry, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Connect you to the menu of the router from a work computer and make sure DHCP is on, and it is configured to assign IPs which can cover the number of computers that are connected (a bit more will be even better).

  Turn off the computer and the router, reset the router and the computer.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  It still does not work, try this too.

  Firewall software.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall Windows Firewall should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly, or uninstall it completely allowing the clean flow of traffic on the local network. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Reset the network stacks .

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP, just replace the command typed with.

  netsh int ip reset

  Restart the computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Connect the 2 locations using RV016 router to fill 2 different networks.

  I have a RV016 connected to a comcast cable modem to slot 1 with IP 192.168.6.1

  I have a RV016 connected to a comcast cable modem at the 2 with 192.168.10.1 IP location

  I installed a VPN tunnel from gateway to gateway between 2 routers RV016.

  I have a LAN in slot 1 with the IP 192.168.1.1, which connects to the internet through an Adtran router with 4 lines of T1 servile.

  I have a LAN with IP 192.168.5.1 2 location that connects to the internet through an Adtran router with 3 T1 lines servile.

  I like a computer to location 2 to connect to the RV016 in the local Comcast modem to the Comcast modem at location 1 in the RV016 to slot 1 then go out to the local network at location 1 and communicate with an application server on LAN 1.

  Help, please.

  You can't do that with a RV016. The RV016 only supports layer 3 tunnel. This means that the two ends are different networks with different subnets. The traffic between them is not filled.

  If you want to really two bridged networks, i.e. join in a single LAN with a single IP subnet and a single broadcast domain you need a layer 2 tunnel, for example a tunnel L2TPv3. That works on layer 2, which is on the MAC addresses inside your networks. In this way, you can use the same IP subnet at both ends and on each side, it seems that the other side is connected to the same ethernet network.

  The RV016 does not support the tunneling of layer 2. You can create an IPSec tunnel, which is layer 3. If there is really a need for a tunnel layer 2, you get different devices. I recommend that you evaluate if a layer 2 connection is really necessary or not.

• Cannot get location using the network provider

  Hi all

  My android app uses the location updates and works very well on the Android device. I wore my application on 10 BB, I can get updates of location using GPS_PROVIDER but do not NETWORK_PROVIDER. Anyone who manages to find the location using the network provider?

  Kind regards

  Nishant Shah

  According to the taking in charge:

  "It is a known problem that is being fixed with internal development."

• The cloud of document can be used as a network location for the sending of request for comments to a greater number of commentators?

  The cloud of document can be used as a network location for the sending of request for comments to a greater number of commentators?

  I manage not rather these comments by e-mail, and we do not have a webdav server that is accessible from the outside.

  Thank you

  Hi Jeff,

  No you cannot use Doc Cloud for this purpose. For detailed information, please see the following link: using Acrobat | Prepare a PDF review

  Kind regards
  Rahul

• How can I use Powershell to create shortcuts "File Folder" in the section network location?

  Hello

  I am trying to create a powershell batch file that will create a bunch of shortcuts to files to Sharepoint document libraries network.

  To get an idea, the manual method would be to go to computer--> right click--> Add a network location

  From there, I can enter the path of the URL to a Sharepoint document library and it will create a folder shortcut in this library of documents that allow people access to the library without having to go through Sharepoint to access.  So when the user clicks the shortcut, it opens an Explorer window to view and manipulate the files.

  I found the script next, but it will create a shortcut 'Internet' when I put in the path instead of a shortcut of the file folder. So when the user clicks on it, it just opens the web page.  Any help would be great!  Thank you!

  [Environment]: GetFolderPath ("ApplicationData")
  $path = [Environment]: GetFolderPath("ApplicationData") + '\Microsoft\Windows\Network Shortcuts\ACL Documents.lnk.
  $comobject = new-Object - comObject WScript.Shell
  $link = $comobject. CreateShortcut ($path)
  #targetpath can be the UNC path or physical path to .exe
  $link.targetpath = "https://finance.domain.net/ACL/Shared%20Documents".
  $link. IconLocation = '% SystemRoot%\system32\imageres.dll,137 '.
  $link. Save()

  Thank you

  Hello

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the best support.

  http://social.technet.Microsoft.com/forums/en-us/category/SharePoint2010, sharepoint