New disks sata hard

Similar Questions

• New disk SATA hard for HP Pavilion Elite m9065.uk, a desktop PC

  I am wanting to buy a new hard drive for my HP Pavilion Elite m9065.uk, a desktop PC. Here are its specs:

  http://support.HP.com/us-en/document/c01242071

  Now, the material is not my specialty. I know that I need a SATA drive, but I don't know that one to buy? I will be limited to the capacity of HDD can I install it? I would ideally like to 1 TB.

  I guess I can't install a player?

  Thanks a lot for any advice.

  Hello

  Your computer is fairly new, you should be ok, installation of a 1 TB drive.  Older computers may have problems of card motherboard/bios with bigger hard drives.  You can also install a SATA2 drive, but if your motherboard doesn't support SATA drive will just default to this speed (SATA2 is backward compatible).  The player below is to consider.

  http://www.Amazon.co.UK/Seagate-Barracuda-7200-12-drive-cache/DP/B0024FAN24/ref=sr_1_5?ie=UTF8&QID=1287523497&SR=8-5

  Hope this helps,

  DP - K

• I can't install the second disk sata hard

  I have a problem when install the second disk sata hard
  I bought a new one 500 GB and I installed windows xp sp3
  and it works well I plugged in SATA 0 port
  When I want to install a second sata hard disk 320 on sata 1
  and it has an important data, windows will reboot, and do
  blue screen sometimes 'NTFS.sys"or"SCSIPORT.sys.
  and it is written "DRIVER_IRQL_NOT_LESS_OR_EQUAL".
  If someone help me what should I do or there is no FIX for this problem.

  in the BIOS I have regcognized both hard drivers:
  IDE pri master 500 GB
  PRI IDE slave 320
  Second master IDE-
  Second slave IDE-
  PORT SATA - 0
  SATA 1 - PORT

  I plugged the IDE 2 cd-rom

  ----------
  Specification of the device:
  Windows xp sp3
  card mother gigabyte 848P
  Intel ICH5
  Intel 8I848p775-g
  Celeron D Socket 775

  You said that the hard drives are sata but your bios recognizes them as IDE depending on your position. You might have to set your bios to operate in sata mode or enable AHCI of have recognized them as sata. Regarding the error you get, look in the system BIOS to boot from hard disk command menu. This is different from the command menu of usual starting where you choose each time you start a cd ROM or hard drive ect... The parameter that I refer to determine which hard drive of your computer starts on the first. Change to the primary master 500 GB disk > save your settings and restart your computer. Even if one is defined as main and the other slave is not serious. Some bios have the ability to choose what hard drive to boot from. In other words, it is adjustable to start first on the slave drive.

• How Windows XP Setup (F6) to use an instead of a floppy drive usb flash drive to find the drivers for a disk sata hard

  Hello

  How can I install Windows XP Setup (F6) use an instead of a floppy drive usb flash drive to find the drivers for a disk sata hard.

  Kind regards
  Imane

  Hi Mike,.

  You can not install it. This must be done using the floppy drive. This feature is available for Vista and Windows 7.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• the upgrade of the disk sata hard to new ssd sata 3 disc 1

  I have Hp m9510 running windows 7 64 bit home edition.  The motherboard is ASUS IPIBL-LB (Benicia), my drive sata hard existing 1 running in raid mode.  I want to add a new SATA of SDS 3 as a new startup disc and leave the player sata 1 existing as a backup.  Insofar as the motherboard is built for sata 1, if I install a sata pci card 3 I will then be able to obtain the transfer of higher data rates of the new ssd without causing other problems?

  If your current configuration has a single disc, then your default would be AHCI.

  RAID stands for redundant array or inexpensive disks and requires two or more physical hard disks for the implementation.

  In this case the preferred configuration would also be AHCI. It's a SATA mode. (Advanced host configuration interface) His replacement is IDE (emulation) mode

• Unable to format my new drive sata hard with windows.

  I bought a new (raw) sata Western Digital 2 TB Caviar Green to use as a second hard drive in my system.  I installed it fine and BIOS and windows recognizes it.  I assigned a drive letter with disk management and made the active partition.  In disk management, it shows: Disk 0 basic 1863.02 GB Online - (m :)) healthy (primary, Active Partition BRUTE))

  The last thing I have to do to make this drive work is format.  What windows seems unable to do.  If I try to do a quick format within two minutes, I get the message "Windows was unable to complete the format".  And when I tried to do the complete method it seemed to do very well, after about 90 minutes, it was made, to halfway and then six hours later the bar had not progressed at all.  Which forced me to restart my computer I could do something for her again.  Before restarting, he kept saying that I didn't have permissions to do something for the reader.

  Normally I think it was a bad drive, but about six months ago, I bought seagate 1.5 TB internal a drive and exactly the thing happened, I ended up sending this rear disc.  Now I start to worry, it's something else.

  I am running Windows Vista Home Premium x 64 with service pack 2, I have protection anti-virus and Windows updates to current day without any problem.  5 GB of ram, AMD image treatment.

  Hi Calabrel,

  In NVIDIA driver downloads: http://www.nvidia.com/Download/index.aspx?lang=en-us there is one ' Option 2: automatically find drivers for my NVIDIA products ", click the DRIVERS of motherboards. Simply download active x NVIDIA Smart Scan Tool.

  I hope I could help

• How to add a row in a computer using New-disk virtual hard?

  Hello

  I am running powercli 5.0.1 build 581491 and I'm writing a powercli script for:

  (1) create a RDM

  (2) assign the RDM to VM1

  (3) assign the same RDM to VM2

  I am able to create the ROW and assign it to VM1, but I am unable to use "New drive" assign to VM2.  Using the following command, I am able to create the ROW and assign it to VM1.

  New-disk-hard - VM VM1 DiskType - RawVirtual /vmfs/devices/disks/naa.60000970000192603729533030353531 - DeviceName

  While trying to assign to VM2, I do the following:

  New-harddisk - VM, VM2 - DiskPath ' [san - datastore:1] vm1/vm1_1.vmdk.

  And I get the following error:

  New-hard drive: 06/06/2012 14:13:19 new-support device Incompatible hard disk specified for the device '0'.

  What I realized, is that if I create a regular vmdk file, then use the New drive using the '-DiskPath ' option, then the command works well.  So my question is, what is the command to add a ROW in a virtual machine?

  Thanks in advance.

  No, indeed it seems something wrong with the cmdlet New-disk hard when adding shared RDMs.

  I have the following, which assigns the RDM common to both virtual machines.

  It's more or less the same, what you've seen in Onyx, but it adds the RDM shared for two virtual machines.

  $vm1 = Get-VM -Name VM1 $vm2 = Get-VM -Name VM2
  $DeviceName = "/vmfs/devices/disks/naa.600507680180701ed00000000000124" 
  
  $hd1 = New-HardDisk -VM $vm1 -DeviceName $DeviceName -DiskType RawVirtual $ctrl1 = New-ScsiController -HardDisk $hd -BusSharingMode Virtual -Type VirtualLsiLogicSAS
  $spec = New-Object VMware.Vim.VirtualMachineConfigSpec
  $spec.DeviceChange += New-Object VMware.Vim.VirtualDeviceConfigSpec $spec.deviceChange[0].device += $ctrl1.ExtensionData $spec.deviceChange[0].device.Key = -101$spec.deviceChange[0].operation = "add"
  $spec.DeviceChange += New-Object VMware.Vim.VirtualDeviceConfigSpec$spec.deviceChange[1].device += $hd1.ExtensionData$spec.deviceChange[1].device.Key = -102$spec.deviceChange[1].device.ControllerKey = -101$spec.deviceChange[1].operation = "add"
  
  $vm2.ExtensionData.ReconfigVM($spec)
  

• Don't see disk sata hard in windows Explorer 7

  I have an abit fatal1ty fp in9 sli motherboard with 2 GB of ram.

  I have a drive hard western digital 2 TB green with win 7 ult 64 on that.

  I added internal a drive hard hitachi 2 TB sister sata as a hard drive.

  I see the hitachi in the bios and in Device Manager.

  Device Manager indicates that the drive is installed and in good health.

  I don't see the hitachi drive in windows Explorer.

  I can see an old drive hard ide and the boot drive, but not the new hitachi in Solution Explorer.

  I've added the fix Windows6. 1 kb977178-v2-x 64.msu which is hot fix 404474_intl_x64_zip.exe

  It's funny that I can see in the Device Manager but not explored, I tried new scanning devices and reboot several times.

  any ideas?

  I fixed it!

  in Explorer, right-click on my computer and select manage.

  in the computer management screen select mangae hard disks and create a partion on drive of choice and format her!

  Sometimes the simplest things are the most difficult to do!

  Maybe this will help someone else.

• Regarding the restoration of the Windows 8 of recovery on a new disk media HARD empty.

  I have a HP Pavilion laptop pre-installed Windows 8 (under warranty) and I get a new drive HARD HP vacuum in replacement.

  I have already created a set of recovery media.

  My question is that I would be able to install the Windows 8 by using the recovery media (created by me) on the new empty hard drive?

  and what about the key of Windows 8?

  Hello

  Your recovery discs should install windows 8 on a new hard drive with no problems - windows 8 activation key is stored in your notebooks bios chip and will be read automatically by the installation disc.

  To boot from your recovery disks, you will need to disable "Secure Boot" - see the HP document on the link below in this regard.

  http://support.HP.com/us-en/document/c03736054

  Kind regards

  DP - K

• physical disk sata hard d: went in 'Computer', undeleteable cd rom drive d: shows in its place

  windows vista edition operating system home premium

  My d drive is a sata hd with a single partition. It has only the data (no installation of operating system or the program)
  in car disappeared in 'Computer', but it is detected by my bios, it shows as working properly in Device Manager and appears in... Disk Manager but not allocated.

  a CD-ROM cd ghost undeleteable drive shows in places like d:

  so far, I tried the following to resolve this situation:

  1A ran full virus/spyware scan, computer diagnosis, etc...

  2. remove all virtual disk software for example daemon tools, power iso etc...

  3. start in safe mode

  4 running msconfig and try different boot configurations

  5. physically change the sata connector on the motherboard of the drive is plugged

  6 unplug the drive from, then stop to connect player departure and back again

  7 tried to restore to the point before this happens

  None of them brought no success, if anyone has a solution for this, please report it. I would not lose the data on this drive!

  Hello

  The CD Phatom drive appears in Device Manager as well?

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  ----------------------------------------------------------------------

  If necessary:

  Make a Restore Point

  Start - type Regedit in the search box - search at the top of list - click on - RUN AS ADMIN

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  Look here and the other keys to CurrentControlSetX\Enum\IDE where X is a number.

  Right-click on the PHANTOM drive and EXPORT the key to name something you remember. Then
  Once again right click and delete it. Do the same for all people.

  Whether it's there or not go back to Device Manager - right click on the hard drive (D :) and UNINSTALL it.
  The reader should be located and re-installed when you restart after checking the GHOST.

  If the GHOST is still there, see if you can DELETE it now.

  If you can or not - RESTART.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• I recently installed a new disk of hard on my laptop, is there a way I can still use my OS to a new hard drive? pls help

  I recently installed a new hard drive on my laptop, and Ive had an activation problem my windows 7 OS, it says that I cannot activate my OS on this machine, is it possible that I can still use my OS to a new hard drive? pls help

  You must activate by phone and speak to a representative of activation.

  How to activate Windows 7 manually (activate by phone)

  1) click Start and in the search for box type: slui.exe 4

  (2) press the ENTER"" key.

  (3) select your "country" in the list.

  (4) choose the option "activate phone".

  5) stay on the phone (do not meet all the automatic guests) and wait for a person to help you with the activation.

  (6) explain your problem clearly to the support person.

• Try turning off hard/reactivate the new disk drive hard breaks down

  I have a computer with a failed hard drive and tries to disable my Acrobat Pro XI. We tried to turn off and try to go on a new hard drive and are not able to transfer through. What can I do to fix this? Thank you

  to turn off (make sure you have your serial number), open the default Acrobat > click Help > deactivate.

  on the new hd install acrobat and activate with your serial number.

  Available downloadable Setup files:

  • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | Suite X | 9,8 | 9 standard | 8 standard
  • Captivate: 8 | 7 | 6 | 5.5, 5 | 1
  • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2
  • Lightroom: 6| 5.7.1| 5 | 4 | 3
  • Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
  • Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• [Y550] New HDD SATA III. Is it compatible?

  Hello.

  I want to know if I can change my original WD hdd (I'm preety sure it's SATA I), again SATA III? I don't know if the motherboard will be compatible with SATA III. What do you think?

  And by the way, what model of motherboard is in it? Unfortunately, my serial number fail to pass on the support site, so I can't check the configuration it (and my HARD drive is broken, so I can't use the software to check it out).

  And the third question: will there be any signs of change if I Exchange my hdd SATA III. I don't know if it is important in Y550.

  Thanks for all your responses in advance.

  See you soon,.

  Peter.

  Hello
  Welcome to the forums
  In the y550 sata port is sata 2. If the disk sata hard 3 would also go to sata 2 speed. This is common for all models y550
  If you know the configuration of your computer, you can view the psref removed systems and it corresponds with the model No.
  http://www.Lenovo.com/PSREF/psrefs_withdrawn.html
  The sata 2 would be faster than the sata 1 and that means faster data transfers.
  Concerning

• E0M30UAR (ENVY 15): speed SATA hard drive in an E0M30UAR (ENVY 15)

  Given to replace the hard drive in my E0M30UAR (ENVY 15) with an SSD.  However, I would like to match the drive to the potential of the laptop.  How fast is the SATA interface in an E0M30UAR (ENVY 15)?

  Hello:

  Run this little program, I compressed upwards and attached below.  Conclusion of the available update.  It is the latest non-beta version which I enclose.

  Conclusion of the report screen which shows to the top and on the left side of the window, click to expand the report to readers.

  Click to expand the report of atapi sata drives, then select your hard drive.

  This report will give you the current speed of the disk sata hard and the speed of disk controller.

  You are interested in the speed of disk controller.

  For example, my report shows Serial ATA 6 GB/s @ sense 6 GB/s, I have a drive sata hard 3 running on a sata controller 3.

  If you have a SATA 3 and a sata controller 2, it will notify if you Serial ATA 6 GB/s @ 3GBPS.

• How can I get windows xp to recognize a new disk of 1 TB sata hard?

  How can I get windows xp to recognize a new disk of 1 TB sata hard?

  Hello NavarroIT,

  In addition to the previous comments, I have link for HD is not recognized.  It is an external drive.  However, without knowing the manufacturer of your hard drive, you will need to check on this end.  You may need to format the disk first.  I hope this helps.

  Microsoft Answers: External hard drive

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-hardware/external-hard-drive-is-not-recognized-in-my/8464edf9-d8b4-4afb-bd91-13d639c23c9c