New error message after upgrading the hard drive and operating system installation

Similar Questions

• Product key in the usage message after upgrading the hard drive.

  I missed my activation need help

  I bought a new and larger hard drive. I installed my copy of Vista on my new hard drive. I have inadvertently has my old hard drive connected when I tried to activate the new vista installed. now it says my product key is already in use.  I replaced my hard drive before but this time I did it wrong. I want to format my old drive, but I can't afford a different product key. I'm afraid to format my old drive now that I could end up without any operating system. How can I use my new hard drive as my main C: drive and my old drive for storage of files without having to purchase another license?

  It is quite normal - your key is used by your previous installation.

  You need to re - activate by phone.

  telephone activation.
  Click the Start button
  in the search box, type
  SLUI 4
  and press the Enter key
  Follow the instructions - but when asked which service you need the ansafone phone, don't answer - it should oblige the operator to answer, who can deal with you.

• I currently store my pictures on and an external hard drive.  Lightroom 6 was not able to find the picture momentarily files.  I inserted an external Flash DRIVE after removing the hard drive and the computer renamed the stick with the same drive letter t

  Redesign existing external hard disks and still 6 Lightroom able to find existing photos.

  I currently store my pictures on and an external hard drive.  Lightroom 6 was not able to find the picture momentarily files.  I inserted an external Flash DRIVE after removing the hard drive and the computer renamed the stick with the same drive letter that has been designated by Lightroom to store my photos.  I could go into my Windows 10 and reset the player to the letter that Lightroom has given at the beginning of the external hard drive.   However, I know this can happen again, if I connect any stick USD or another device, while the external hard drive is not connected to my laptop.   I found the information that I can do the new designation of the final drive by choosing a letter it is 1/2 way or higher in the alphabet.   I would like to turn an external hard drive on a strong letter, warns we hope this previous problem.   My question is, if I already have a lot of pictures on this external hardrive with the designation of the current drive, how it becomes a higher letter and have 6 Lightroom recognizes files, now under the new designation of drive letter without having to go to each photo individually and manually force Lightroom 6 find each photo.  It would take more time than I'd like to lose.  Is there a way to get just 6 Lightroom to recognize the new disk designation has changed and is able to find all of the existing files?

  I have read the ADOBE LightRoom 6 manual and seem not to be able to find anything on how to do it.

  Any help would be welcome.

  Thank you!

  So in Windows, you can select a drive like q letter (or any other letter you want only towards the end of the alphabet)

  Then in Lightroom, you can reconnect to the photos on q: the following instructions (see specifically 4 Figure and related text)

  Adobe Lightroom - find moved or missing folders and files

• Satellite U205-S5002: cannot retrieve the Express Media Player after upgrading the HARD drive

  So I bought just a new Toshiba Satellite U205-S5002 I love it. One of the great features that interest me was the Express Media Player feature.

  My first step was to upgrade the hard disk and 160 GB and 2 GB ram.
  I placed the disk and ram in my old laptop and sold it.

  Before that I did, I made a copy ghosts and ghost of the hard drive to the new drive. Well come to find out...

  Toshiba is not provided with this software preinstalled, so I followed the instructions to burn my recovery disk Express Media Player and the boot on the new disk.
  So this is where the saga begins...

  After 15-20 seconds, I get a soothing blue screen (NOT of blue BSOD you mind) who says:

  /!\
  An error occurred during the recovery of "Express Media Player".
  -------------------------------------------------------
  Please pick up the image again from the beginning.
  Press any key to exit.

  It is typed exactly as it is on the screen. So, I see some other forums saying: you must have the free space of the disk so I resize the partition that allows 200 MB of space. Always the same... then try 2 GB even... then the 50 GB, same problem...

  OK, so obviously not a question of space. I read while I might need to erase the drive... so I delete the partition, this same error... then I run the recovery disk and tell him to wipe the drive, wait 1 1/2 hour, it ends. No dice! So I decide... ok... Well lets try another disk... I have restored my ghost image... and burned the image again... same question... so I decide to the recovery disk and I'll try to reinstall windows in the factory and make a record...

  Well, it does not work as well as you think... the image is incomplete... windows works fine... but the c:\Toshiba\ExpressMediaPlayer folder is empty!

  I'm happy that I have ghosts my original directory. But I decide allows to Express Media Player a shot more now that I have restored to factory... always the same error... I then decide a trial more... I'll erase drive 1.5 hours, I'll restore from toshiba dvd provided but leaving plenty of space at the end 2 GB (I have a lot about people who tell you to base just around 200 MB)

  5 hours later... moment of truth... Well Yes you guessed it... I don't know anything else to try... I have a bad image?
  You need one that I can download what has worked for them for sure? Or have - I have completely found myself by replacing the HDD with after market and which is originally a kind of compatibility issue?

  Thank you in advance.
  Gabe at supergeekz dot com

  Hello

  It s a great story!
  I put t know how to start so maybe first some info on the Express media player.

  As you said, and has already proposed the Express media player has been preinstalled on the second partition.
  If you want to install this media Express on the HARD disk drive, 150-200 MB of free space must be available. This free space must be on the end of the HARD drive and there must be unallocated.
  To get these free space on the HARD disk, 3 third-party products should be used as for example the Partitions Magic 8!

  I'm not going to write a story how to recover the Express media player because Toshiba has already created useful documents, which described complete installation!
  I found these documents in the knowledge base of computer Toshiba:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=TIC2

  * Check this box: *.

  [Why Express Media Player fails to run after replacing HARD drive or recovery? | http://support.Toshiba-tro.de/KB0/FAQ5C018T000FR01.htm]

  [How to recover a laptop Expert Mode with 2 Partitions and Express Media Player? | http://support.Toshiba-tro.de/KB0/TSB58014O0008R01.htm]

  Hope I could help you.

• No DVD drive after upgrade the hard drive on Satellite Pro A100

  Shortly after upgrading my hard drive, optical drive has stopped working, now is no longer appear in 'My computer' or Linux. Device Manager says:
  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  I tried to reinstall the drivers, the DVD-RAM drivers, and the DLA software.

  All ideas are much appriciated.

  Edit: I just tried an external drive and it has the same problem, it seems to say

  Post edited by: theplatypus

  Error 39 has been described much time here in our small community ;)
  Please check this thread for example:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13843&MessageID=50483

  You will find a link to the MS knowledge base document that describes how to solve this problem.
  Use of the method 1: remove the registry entry

• missing hal.dll message after removing the hard drive

  Original title:Ok, I had the same problem on my hard drive missing hal.dll. My question is what windows xp writes the cmos on my computer?

  OK, I had the same problem on my hard drive missing hal.dll. My question is what windows xp writes the cmos on my computer? The reason why I ask, is that I physically removed the hard drive from the computer and then start the computer I get the same message hal.dll lack. Since the hard drive is not installed, the only place where this message comes's cmos or bios of the computer.
  I know it seems odd, but I couldn't believe it when I saw it after removing the hard drive. It used to be with older computers and Windows 95 or 98 when you took a hard drive that wasn't working and installed with one that works from a different computer, you could swap out and boot the computer and make a few changes to some drivers if you.

  So what is windows xp write to the memory cmos on my computer?

  > Ok, I had the same problem on my hard drive missing hal.dll.

  The same as what? If you reference another thread, please include a link to it.

  > My question is what windows xp writes the cmos on my computer?

  It is not write anything for her at all.

  > Lack of the reason why I ask this is that I physically removed the hard drive from the computer and then start the computer I get the same message hal.dll.

  I think that you're wrong. I would like to say two things happening:

  1. you have more than one hard drive and the problematic drive was not removed, or

  2. you deleted something other than a hard drive.

  Do you have a CD in your CD drive by chance?

  What is the brand and model of your PC? Are you able to get into the BIOS?

• Upgrade the HARD drive and install SSD XP to Windows 7 upgrade - which command?

  I want to make some improvements to my trusty HP XP media center PC m7350n.  Ideally, here's what I want to do in a certain order:

  -upgrade the HARD drive (currently 250 and 500 GB installed, replace with 750 unique?)

  -install an SSD as boot drive (60 to 120 GB?)

  -Reinstall XP restore disks media center

  -do a upgrade 'clean' for win 7 Home premium (64 bit?) from the disc "upgrading"

  The Windows 7 upgrade disk looks like for XP/Vista, so I can't put new hardware and go directly to a cost of Win 7 install.

  Plan a.

  I understand the look of for the minimum size of disks restore disks.  All guess what SSD size would be the minimum? I guess the upgrade of the first hard drive and reinstall XP MC since the restore disks would be trivial (as opposed to their use after a motherboard replacement).  If I have XP MC on the SDS, it is only a reason any Win 7 no upgade SDS?

  Plan B

  If I install the SSD after upgrade to Windows 7, I guess I have to use something like a disk copy program to the boot from SSD HARD disk partition.  SUGESTIONS?

  Plan C

  Restoration of SKIP.  Move existing partitions of 250 and 500 GB drives to 750.  Update for Win 7.  Install an SSD.  Move the boot partition.  Use the same drive for both copy program?

  Am I missing something?

  In case anyone is wondering, I have a spare 750Go drive and the Windows 7 upgrade disk so the only "cost" of this update is to purchase the SSD (and if necessary disk copy program).

  Thank you!

  Don

  donprice11 wrote... I want to make some improvements to my trusty HP XP media center PC m7350n.  Ideally, here's what I want to do in a certain order:

  -upgrade the HARD drive (currently 250 and 500 GB installed, replace with 750 unique?)

  -install an SSD as boot drive (60 to 120 GB?)

  -Reinstall XP restore disks media center

  -do a upgrade 'clean' for win 7 Home premium (64 bit?) from the disc "upgrading"

  The Windows 7 upgrade disk looks like for XP/Vista, so I can't put new hardware and go directly to a cost of Win 7 install.

  Don,

  Please read this article by Paul Thurrott more "Clean install Windows 7 with upgrade media '. It essentially says you can make a completely clean install on a drive with no operating system. The key is not to enter the COA product key after installation is complete. I, myself, installed Windows 7 to discs using disks 'upgrade' several times without problems of installation or activation. The order I do it with, is as follows:

  1 copy all the files and folders of the 250 and the 500 GB HDD of 750 GB.

  2. remove the 250 GB, 500 GB and 750 GB of computer hard drives.

  3. install the SSD.

  4. install Windows 7 on the SSD without entering the product key.

  5. Once finished Windows 7 installation, enter the product key and activate Windows.

  6. return old hard disks of computer as needed.

  7. install purchased software and Windows updates if necessary.

  You should go to 4 GB of RAM to get the most out of Windows 7 64 bit and you can upgrade your graphics card.

  Note: You will lose all software provided CVS Windows XP on your m7350n. Make sure that you create your HP recovery discs before you proceed with the change of equipment or install Windows 7. Your HP recovery disks can have the factory included HP software... it may or may not work with Windows 7. Good luck and let us know how it turns out.

• Computer HP Desktop M1188A upgraded the HARD drive and memory upgrade possible

  Hello

  I have a HP Desktop M1188A running XP Media Center 2005.  The computer runs very slowly and was only 27.6 GB of free space left on the hard drive with a total area of 149GB.  It has 512 MB of memory installed a 4 GB maximum.  Speed supported is PC3200 MB/sec.  Type of DDR.  DIMM slots 4.  160 GB 7200 RPM SATA hard drive.  Fact hard drive 160 GB 7200 RPM SATA means it is a SATA connection?

  I want to switch the HARD disk like this I hope that the computer runs faster.  I'm a complete novice with respect to the operation of computers.  What to buy to upgrade the HARD drive?

  Will it also upgrade the installed memory?  If so, what to do?

  Everything I need to know?

  Thank you.

  See you soon,.

  Michelle

  Michelle,

  Try for battery HP to THE Bing search engine, I found several sites in line with the Chargers and batteries. BattDepot Australia seems to have decent prices... At$ 24.49 for the loader and THE $37,49 for battery. If you have not yet checked the HP battery reminder page, I recommend you do this first.

  Frank

• Tecra S11 - How to reinstall Windows 7 after upgrading the HARD drive?

  How to reinstall Windows 7 pro after an upgrade to 500 GB HARD drive? How to access password protected data after relocation? How can I get a professional installation of Windows 7 DVD?

  (I do not installed new HARD drive yet, but I intend)

  Hey Buddy,

  You have created the Toshiba Recovery disk? Perfect!
  After Exchange of HARD drive, you need this you to install Windows 7 disc. The Toshiba Recovery disk contains an image of the factory settings, which means that you will have the factory settings on the new HARD drive after the use of the disc. You must boot from it and follow the instructions on the screen.

  > How to access password protected data after relocation?
  It would be interesting to know what data you mean exactly.
  Before you reinstall Windows, you must back up all data on a disk for example external HARD.

• can I reactivate windows 7 by using the ID of the original product after upgrading the hard drive.

  Original title: reactivate Windows 7.

  I want to spend the hard drive on my laptop.

  The question is, when I remove the old hard drive and put a new, obviously, I need to install windows on the new drive system, can I reactivate windows 7 by using the ID of the original product?

  If this is not the case, how can I do?

  Thank you.

  How to pass windows 7 to a new hard drive using Acronis True Image Home 2011:
  A step by step guide on the use of Acronis True Image Home 2011.
  http://www.PAGESTART.com/acronisnewharddrive01.html

  (Note: Acronis is now 2014, but the technique is the same)

  Other Image backup options:

  Acronis True Image 2014 - has a 30 day trial version available, key to test sent to your Email address.
  Note: Initialization of cloning and the road (creating a MBR) are not supported in the trial version.
  For the trial version, the recovery is only available when starting an Acronis Bootable Media CD.
  Install Acronis and then create a bootable media restoration/rescue CD before you start creating your first backup image
  http://www.Acronis.com/homecomputing/products/
  30-day trial: http://www.acronis.com/homecomputing/products/#tryorbuy
  True Image User Guides and documentation:
  http://www.Acronis.com/support/documentation/
  2014 supports XP, Vista, Windows 7, Windows 8 and 8.1

  Paragon
  Free version: http://www.paragon-software.com/home/br-free/
  Guide: http://www.paragon-software.com/home/br-free/download.html
  Home Version $ 39.95: http://www.paragon-software.com/home/brh/
  Support: http://www.paragon-software.com/support/

  Macrium Reflect free
  Free version: http://www.macrium.com/reflectfree.aspx
  (no technical support available for the free version)
  Macrum reflect Standard ($49.99)
  http://www.Macrium.com/personal.aspx
  Suport: http://www.macrium.com/ticket.aspx

  Note: For users who have a Western Digital hard drive, there is a free version of Acronis 2013:
  http://support.wdc.com/product/downloaddetail.asp?Swid=119
  Release notes: http://support.wdc.com/download/notes/ATI_WD_RN_5962.pdf
  Guide users for WD Version: http://support.wdc.com/product/downloaddetail.asp?swid=119&type=userguide&wdc_lang=en

  How to pass windows 7 hard disk nine or greater using the backup and restore of Windows 7
  http://www.PAGESTART.com/win7bckuprstrnhd072610.html

  After you moved to the new drive and are convinced that everything is working Ok, then you can format the drive or temporarily start from the old drive and open a prompt (run as administrator) and quick entry: slmgr /upk and press ENTER.  This allows to uninstall the product key from the old drive.

  J W Stuart: http://www.pagestart.com

• Indexing not runing after upgrading the hard drive, sfc/scannow reports corrupted files.

  I replace my hard drive using a system repair disc and a system image on 4 DVDs

  Everything works well except the Win 7, that it is not authentic. I intend to deal with this later.

  Then I noticed that indexing does not work

  Went to research, indexing options, advanced, it says indexing does not work

  Select Advanced, rebuild, it simply works and runs,.

  I tried - C:\windows\system32>sfc/scannow, he reported 100 percent complete audit.

  Windows resource protection found corrupt files but was unable to solve some of them

  Details are provided in convertible bonds. Journal windir\Logs\CBS\CBS.log.

  I can open the file, but it is 1 MB of data, and I have no idea what this means

  Help

  Fact activation of "in person" who has been a success, but no real messeages returned.

  Called MS - after obtaining a level 2 tech and after much digging, installed Intel Rapid Storage Technology Application SATA/RAID support (I don't have a RAID).

  That fixed all problems!

• Windows 7 says this isn't authentic after changing the HARD drive and can not activate

  After a Windows Update I received a notice that my version of windows was not authentic, which is false because I had windows on my laptop because I got it 4 years ago. Recently, I had to have the changed HARD drive as it corrupts. Installed new HARD drive and partition it a space in which the old files to hard drives. Seemed to turn very well when HARD drives were exchanged and windows installed on the new drive until windows update. My Microsoft certificate key is passed out to illegible but I don't have the product key for the OEM version. Any help would be great, thanks.

  If Windows was preinstalled on your computer, you can enable using the code from the sticker on the computer.  If you can not read the sticker more, you will need to contact the computer company he built.

  If you purchased Windows from the store, you can enable using the code of the case/box/CD.  If you can't read it, you must contact the retailer who sells to you.

• Windows Update service will not work after upgrading the hard drive

  I'm running Windows Vista 64 bit, Home Premium SP2 with 8 GB of ram. I recently cloned my hard drive OEM of 500 GB, 5400 RPM Toshiba MK5055GSX via a standalone, dual drive bay dock for upgrade to a 750 GB, 7200 RPM, Western Digital WD7500BPKT. Since the clone/upgrade, Service Windows Update does not work and gives the message: ' Windows Update cannot currently check for updates, because the service is not running. " You may have to restart your computer. "And Yes, I checked and everything related to Windows Update seems to be 'turned on' or well defined, but the service will not work. Notes; Windows Update still works with the player "OEM", it is only the new WD drive that has the problem. Thanks in advance for any help or suggestion on getting this problem is resolved.

  This fixes my laptop http://www.realworldrobotics.com/troubleshooting-help/windows-7-64bit/windows-update-service-not-running-after-upgrading-drive

• message after replacing the hard drive is. "This computer is not running genuine Windows.

  The original hard drive has been cloned, but the error occurs 2 - 3 times a day.

  I activated the windows via the phone edition and it said activation sucessvull jet message returns

  I tried to reinstall windows and after loading all software the message windows cannot run on this computer

  The system restarts and uninstall success windows and restores the original defective

  It is a HP PC comes with Windows Vista and was then upgraded to Windows 7. has run like that without problems, then the HD had to be replaced which started this problem

  Keep in mind that a clean install as it will wipe your computer, so if you don't have a backup, make a partition.

• after upgrade the hard drive on mac, photoshop starts and freezes

  Hello

  I recently updated my hard drive.

  I used clone carbon copy for any movement of the former.

  Attempted to run Photoshop - without success. Interface of the PS of the charges, but the mouse cursor passes immediately to the Rainbow to turn round.

  Went through the upgrade complete of all Adobe products. Everything installed successfully. The same result as before.

  Downloaded and run AdobeCreativeCloudCleanerTool.zip.

  Some adobe files remained in the Application folder. Remove them manually.

  Restarted.

  Downloaded a fresh AdobeCollection_CS6_LS16.

  Install Master Collection from the new download. Same result.

  uninstall, clean by use the CC cleaning tool to resolve installation problems. CC, CS3 - CS6 and reinstall.

  Available downloadable Setup files:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
  • Lightroom: 6| 5.7.1| 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5.5, 5 | 1
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".