New installation of Windows XP does not - UNMOUNTABLE_BOOT_VOLUME

Similar Questions

• Windows update on the new installation of Windows 7 does not.

  I have several hard drives in a custom PC built and installed Windows 7 on my smaller SSD mainly so I can play Fallout 3 (can not operate in Windows 10@#$%). Everything works fine but just, Windows Update runs and runs. I try to download the updates stand alone, and they just run and run with the message "search for updates on this PC." My Win7 Home Premium installation package had SP1 above. I even tried the update combined KB3125574 and he said that it is not applicable to my PC. From what I understand, MS does not pay much attention to their update servers Win7 more, but I'd appreciate any help.

  Robert Hoefer

  I tried on 2 5?

  When you install Windows, do not apply the recommended settings for the automatic updates. In the "Set up Windows", select ask me later.

  http://www.kodyaz.com/images/articles/Windows7-installation-RC/35.PNG

  Install KB3020369.

  Install KB3172605.

  Best regards, VZ

• New installation of Windows 7 does not start

  I am building two identical systems and have had the same result by installing Windows 7 x 64. The installation goes perfectly well, but when it's time to reboot a few messages and re-positions of the bios as it cannot find the boot partition / OS.

  The CD of installation of windows 7 cannot repair the installation because it "does not support the installed version of windows."

  I did a restore CD that has worked, but he can't find a problem and after reboot everything is there and messages & re-positions.

  Any ideas?

  I finally did a Windows 7 64-bit repair CD and used that to get into the command prompt and use bootrec /fixmbr and then /fixboot bootrec and which corrects the problem.

• Installation of Windows service does not work after Windows Explorer 9 uninstalling and reinstall Explorer 8

  Installation of Windows service does not work after Explorer 9 uninstallation and reinstallation of 8.  I followed several suggestions on this forum, but still no luck.  I ran the SFC system twice, who told me he had corrupted files.  "Some have been repaired and some might not be."  I then went in the event viewer after a start to the top and he stated that the 'Adobe APM service' is not found.  Also the "hpqddsvc' and the 'gupdate' is not found.  He tries to install something every time I start, but he abandoned.  I checked whether the system is on and disabled.  It's on.  There are a lot of small problems, but my main concern is the Adobe program.  I tried uninstalling and reinstalling Adobe, but still get an error message that the Windows Installer Service could not be accessed. Other suggestions?

  Hello

  I suggest you follow the link and check.

  How to troubleshoot issues that may occur when you install, uninstall, or upgrade one program on a Windows computer

  http://support.Microsoft.com/kb/2438651

• new installation of win XP does not updated

  Hello

  I have 2 units of office with a new installation of windows XP Pro top, but when I try to run updates it comes up with code 0x8024D001 error and says "the site has encountered a problem and cannot display the page you are trying to view.

  I have not installed any other software apart from the SP3 and IE8.

  Someone at - it ideas why 2 different units may be the cause of this problem?

  Hello

  I have 2 units of office with a new installation of windows XP Pro top, but when I try to run updates it comes up with code 0x8024D001 error and says "the site has encountered a problem and cannot display the page you are trying to view.

  I have not installed any other software apart from the SP3 and IE8.

  Someone at - it ideas why 2 different units may be the cause of this problem?

  Hi Paul,.

  You must first install Service Pack 3.

  After you have installed, you can run the Fixit on this site:
  http://support.Microsoft.com/kb/2497281/en-GB

• had to install the new hard drive, windows key does not

  My hard drive died in my Inspiron 660. I ordered a new hard drive and a recovery Dell USB key. A recovery key for Windows 8 pro based on my recommended by Dell service tag. I installed the new drive and used the recovery key to install Windows 8 pro. I then used a third-party tool to get the product key from the BIOS. The product key does not work. I wonder if the product key on the BIOS isn't for Windows 8, Windows 8 pro. If so, the wrong recovery key recommended by Dell.

  What should I do to activate Windows successfully?

  Secondly, on my old drive hard, I had upgraded to Windows 10 while he was a free upgrade. How to bring back the free update?

  Windows 8, Windows 8.1 and Windows 10 TH1 and TH2 had problems installing specific edition. Your key can be a simple language edition or one with Bing edition and therefore rejected by the installation of the edition of bad media.

  Windows 10 TH2 and later all the windows 8.x and 7 OEM keys are treated as Windows 10 keys. Edition installation specific issues have been fixed with Windows 10 RS1. The file .iso Windows 10 RS1 image is covering several editions. It contains all OEM editions and will automatically collect a key Windows 8/8.1/10 UEFI BIOS OEM System Locked Preinstallation and automatically installs the correct edition of Windows 10:

  http://dellwindowsreinstallationguide.com/download-Windows-10-OEM-and-retail-ISO/

• New installation of Windows 7 will not identify the second internal hard drive

  Attempted recently to upgrade a computer running the SP3 of XP to Windows 7.  Bought the new FULL version of 7.
  Have two 1 t Seagate Barracuda SATA drives on board; Operating system in partition 1 of disk C:. second disc to store data only.

  Several unsuccessful attempts to install 7, but with helpful suggestions, others on this forum, (i.e., update of the BIOS, re-formatting drive C to do a clean install, etc.) finally managed to a successful installation.

  All right, except that it does not find my second hard drive.  I have the disks attached ports SATA 1 & 2, but the system reads them so much as the C: drive.  The second disc appears in the BIOS Setup and Explorer as just the C: drive.

  Tried to change the SATA port for second drive to 3 and 4 with the same result.  It always appears as the C: drive.

  How can I get the systΦme can recognize the drive, so it can be assigned to a drive letter and I can access?  I suspect that the reformatting of the first disc for installation probably erased some boot sector/configuration info.

  A side issue: before attempting to upgrade to XP, I backed up my "Documents and Settings" on an external drive.  Now that XP is passed to the computer, can I continue to use Windows Easy Transfer to retrieve all my settings and info from the program, or who's going to screw me up?

  Check if the hard drive is assigned to a drive letter in disk management.

  Click Start, right click on computer

  Click on management of

  Expand disk management

  Select your external hard drive if its posted here

  Make a right click paths and change drive letter

  Restart your computer, open the computer in the start menu and see if it shows then.

• New installation of XP, keycode does not

  I recently bought a dozen Lenovo computers.  Some Thinkpad T510 and 400.  Some Thinkstation S20 and E20.  I have them all rights of Windows 7, but with XP pre-installed.  Since they came with a bunch of software assessment and some other junk on them I was just going to clean and reinstall XP.

  As computers have Win 7 rights, the tag on the back is a keycode Win 7 so I used one of the key finders to get the XP key off each machine code and all have the standard Lenovo preactivated key that works only on Lenovos.  So I erased the computer and installed XP Pro on all and all installs it took the keycode.

  Now normally Windows should see this keycode and detect that it is a Lenovo and not need to activate, however it prompts to activate.  But when I go to activate Windows tells me that the code is not valid.

  I have a feeling is what they keycode xxxxx-xxxxx-xxxxx-xxxxx-xxxxx is not match HKLM\Software\Microsoft\Windows\CurrentVersion\ProductID which varies according to the type of CD used to install XP Pro.  For example, if you use a CD XP Pro SP1 OEM to install XP your ProductID registry key will result in:

  XXXXX-OEM-0014324-XXXXX

  And SP2 OEM will result in:

  XXXXX-OEM-0060807-XXXXX

  So the question is, what the Lenovo XP Pro generates a product for the standard CD key identifier?  I probably know the answer if I does not format all the computers at the same time...

  You must get a restore CD XP from Lenovo. (you will need to call them for him) You will probably need to pay for shipping. If your warranty you need to do a no-cost. (by a message I saw by Mark_Lenovo) P.S. the more likely using an OEM XP disk. (as a disc of Lenovo WILL see your key integrated)

• I can't access my external hard drive with windows 7. How can I get my music out of her files? My pc with xp operating system can access it without problem. but my new pc with windows 7 does not see the hard drive.

  I bought a new pc to replace my old hp 14 months as the motherboard fried in. I bought a case of disk external hard to rocketfish to put the hard drive of my Windows 7 pc in. burned does not see the hard drive. my old pc with xp can access all the items on the external hard drive.

  Check that the drive appears in Device Manager.

  If so, go to disk management and assign a drive letter.

• installation of Windows 7 does not detect drivers for 9500S 3ware RAID controller - 4LP

  I've been using 3ware 9500 s - 4lp raid controller without problem on xp64 os.

  I want to upgrade to windows 7, but after installation clean win7 does not detect my readers as unsigned drivers.

  PLEASE HELP ME!

  Please see: Windows 7 Compatibility Center

• Installation of Windows 7 does not connect to the modem broadband.

  I installed characteristic of two different versions of Win 7 64 on my desktop at different times.

  The two does not connect to my modem. I get error 651. I've tried everything.

  I have consulted my ISP, checked the provider. The installer works fine with other OS and Win 7 on another computer.

  My office tells me that there is no driver installed. There is no driver to install.

  I need a connection to the firmware in the modem to work, something that seems missing from Win 7 Home Premium 64.
  Your background of catch-22
  LCW

  See this previous post/answer

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/error-651-in-Windows-7/65077414-15f8-450b-BD19-5cce9a57fcf0

  PS after I clean installed did you get your motherboard manufacturer system drivers, if a generic desktop computer, or if from a major manufacturer, for example Dell/HP support site?

• Satellite C885 - installation of Windows 7 does not continue

  Last week, I bought a C855-21V Satellite with Windows 8 is installed.
  Now I want insstall becauso Windows 7 Windows 8 is not good for me.

  When I insert the Windows 7 CD and boot from the CD, the Installation hangs on the screen which shows "Starting Windows".

  Where is the problem?

  Hello

  It of necessary to change some settings in the BIOS.
  Access the BIOS (F2) and disable secure boot.
  In addition, go to the Advanced tab-> the system setup and change the mode MSC UEFI boot mode.

  Welcome them

• New installation of Win XP does not recognize an ethernet or wifi Internet connection.

  I'm reinstalling an old copy of Windows XP Home edition on a partition on my MacBook Pro and for some reason it gives me the ability to connect to the internet. I can connect with the side the laptop mac, both wireless and via ethernet, but when I boot on Windows, it is not even an option to connect to wireless networks, and he simply ignores the ethernet connection. I tried following a variety of instructions on the web, but no instructions corresponds to what I see on my end. Has anyone else encountered something like this before and know how to fix?

  You must install the network drivers for the Windows operating system. Windows doesn't know how to talk to your devices until you do.

• New installation of Windows will be not updated

  I installed a free version of Windows 7 64 bit on a new generation of computer. Activation went through successfully.

  The problem is that I can't run any programs that need to use internet to get updates. This includes Windows Update, anti virus, or games. I can't even download and run Windows IT. difficulty strange thing is I can surf the internet without any problem.

  Windows Update gives me error codes 80244015 and 8024400 a.

  Any help would be greatly appreciated.

  This is an old question, but it should work

  If looking for updates to hang on a current installation,

  Be sure and go to uninstall a program and see which Microsoft Net framework you have installed.

  4.5.2 is more consistent to have installed,

  https://www.Microsoft.com/en-US/Download/details.aspx?ID=42642

  Switch your windows update setting to never check the updates temporarily

  Restart the machine

  You can try and install the latest client update manually let your update settings to never check for updates until you install it.

  https://support.Microsoft.com/en-us/KB/3138612

  Then you download this from your download folder run from there.

  https://TechNet.Microsoft.com/library/security/MS16-039?f=255&MSPPError=-2147217396

  Download the x 86 for 32-bit or x 64 for 64-bit

  Install it and restart when prompted too after he did a search of stand-alone for updates that should not

  take too long, it took all of 5 seconds, '' If '' windows update settings are turned on forever check

  updates before running from the downloads folder.

  Once it installs and restarts

  You can reset your updates affecting everything you had before default =...

  Then check the updates manually.

  I think that the solution came from Softpedia and Joel_CS posted on this thread,

  http://News.Softpedia.com/news/Windows-Update-hanging-when-downloading-April-12-patches-502886.shtml

  You must scroll down for Joel SC post threads, it is the last answer on this page,

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/Windows-Update-hangs/dbd539c3-bfc6-42DF-a6ff-0e55ef7938eb?page=6

• Installation of Windows XP does not see on Satellite Pro P200 HARD drive

  I just bought a Satellite Pro P200 and I want to install windows XP.

  The problem is the windows installation sayis qhen that there is no hard drive detected.

  The laptop has two HD 200 GB each.

  Can someone help me?

  Thank you

  Hello

  You must first install the Intel Matrix Storage Manager before you continue the installation of XP.
  It s a same as RAID driver installation procedure
  You need to press F6 during installation to include the necessary files of the Intel Matrix Storage Manager

  I found this on the page of Intel:
  http://Downloadcenter.Intel.com/Filter_Results.aspx?strTypes=all&ProductID=2101&OS FullName = Windows * + XP + Professional & lang = eng & strOSs = 44 & submit = Go %21

  Good luck and thanks for posting the results