Similar Questions

• Manager uninstalled drivers and now front usb detect device not

  try to use life cam nx6000. CD did not went to the downloaded driver to internet Manager. then found download microsoft. uninstalled the driver manager and now the usb port before are not detecting the camera or ipod nothing.

  I ran the SFC / scannow, that's where the problem was detected, but like I said I am as far as I can go

  Respond to this request on audio, video, and motherboard and continue with the rest of the instructions.  In other words - skip the SFC/scannow (although where you got the original, I'm not sure.)

  As for the SFC/scannow...  Have you read through this article?
  http://support.Microsoft.com/kb/929833

  In particular, the part that starts with:
  "To determine which files can be repaired by the System File Checker tool, follow these steps:

  and continues with:
  "If the System File Checker tool cannot repair a file, follow these steps:

• SEL18200LE is not compatible with the detection of Phase AF on NEX-6 and NEX - 5R

  Hello

  The SEL18200LE (a black) has recently published is not compatible with Phase detection. I just bought a.

  Do you have Sony will release a new firmware to detection of Phase for NEX - 6 / NEX - 5R?

  Thanks in advance.

  Eric

  Unfortunately Yes.

• What is the difference between the NEX-5 and NEX 5R

  I would like to know what is the difference between 5R NEX5 and NEX to help me choose the best.

  Thank you

  Here are some key differences between the NEX-5 and NEX - 5R.

  NEX-5

  • Sensor CMOS APS - C with a resolution of 14.2 million pixels
  
  
  • video recording Full HD 1080/60i
  
  
  • the speed of 7 frames per second in burst mode
  
  
  • ISO sensitivity up to 12800
  
  
  • Sweep Panorama and 3D Sweep Panorama modes
  
  
  • Autofocus contrast with 25 points

  NEX5-R

  • Sensor CMOS APS - C with a 16.1 megapixel resolution
  
  
  • video recording Full HD 1080/60 p
  
  
  • the speed of 10 frames per second in burst mode
  
  
  • ISO sensitivity of up to 25600
  
  
  • Panoramic scan mode
  
  
  • Quick autofocus hybrid with contrast of 25 points of 99 points phase detection autofocus and auto focus

  In addition, the NEX5R has built-in Wi - Fi that allows you to install applications and extend the functionality of the camera. Built-in Wi - Fi will also allow you to transfer images wireless to a smartphone, Tablet, the computer and the TV.

  If this post answered your question, please mark "accept as a Solution.

• Tunnel of the phase 2's not going up between Watchguard and PIX 525

  Hi people,

  Can you please help me to know where is the problem liying, currently I am trying to establish a VPN tunnel between the PIX firewall and Watchguard, all settings of the two devices are the same, but tunnel Phase two is not coming.

  Here is the fix:

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:500 dpt:500

  Exchange OAK_MM

  ISAKMP (0): processing KE payload. Message ID = 0

  ISAKMP (0): processing NONCE payload. Message ID = 0

  ISAKMP (0:0): payload detected NAT - D

  ISAKMP (0:0): NAT does not match hash MINE

  received hash: b3 8f bb 0 93 3 b 65 e8 35 54 6 c4 cc 59 6f 6f

  My nat hash: dd 9 70 35 58 40 ac da 3 b 5 b 1 b 4 c 87 d2 11 fc

  ISAKMP (0:0): payload detected NAT - D

  ISAKMP (0:0): NAT does not match THE hash

  received hash: ba 72 c5 e 5 b fb 88 f0 1e ba c9 c6 c1 cc 8A f7

  its nat hash: c 4 c 89 a5 66 dd 80 76 48 3f f0 56 ed b0 a5 c1

  ISAKMP (0:0): built HIS NAT - D

  ISAKMP (0:0): built MINE NAT - D

  to return to the State is IKMP_NO_ERROR

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500

  Exchange OAK_MM

  ISAKMP (0): processing ID payload. Message ID = 0

  ISAKMP (0): HASH payload processing. Message ID = 0

  ISAKMP (0): SA has been authenticated.

  ISAKMP: Created a struct 212.37.17.43, peer port 37905 peer

  ISAKMP: Lock struct UDP_ENC crypto_ikmp_udp_enc_ike_init 0x3cbb634, 1

  ISAKMP (0): ID payload

  next payload: 8

  type: 2

  Protocol: 17

  Port: 0

  Length: 23

  ISAKMP (0): the total payload length: 27

  to return to the State is IKMP_NO_ERROR

  ISAKMP (0): send to notify INITIAL_CONTACT

  ISAKMP (0): sending message 24578 NOTIFY 1 protocol

  Peer VPN: ISAKMP: approved new addition: ip:212.37.17.43/4500 Total VPN peer: 16

  Peer VPN: ISAKMP: ip:212.37.17.43/4500 Ref cnt is incremented to peers: 1 Total VPN peer: 16

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500

  ISAKMP (0): processing NOTIFY payload Protocol 24578 1

  SPI 0, message ID = 3168983470

  ISAKMP (0): treatment notify INITIAL_CONTACT

  to return to the State is IKMP_NO_ERR_NO_TRANS

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500

  Exchange OAK_QM

  oakley_process_quick_mode:

  OAK_QM_IDLE

  ISAKMP (0): treatment ITS payload. Message ID = 484086886

  ISAKMP: Check IPSec proposal 1

  ISAKMP: turn 1, ESP_3DES

  ISAKMP: attributes of transformation:

  ISAKMP: Life Type SA in seconds

  ISAKMP: Lifetime of HIS (basic) of 28800

  ISAKMP: Type of life HIS enKo

  ISAKMP: Lifetime of HIS (basic) 32000

  ISAKMP: program is 61433

  ISAKMP: authenticator is HMAC-MD5

  ISAKMP (0): atts are not acceptable. Next payload is 0

  ISAKMP (0): Security Association is not acceptable!

  ISAKMP (0): 14 NOTIFY message protocol sending 0

  to return to the State is IKMP_ERR_NO_RETRANS

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500

  ISAKMP: phase 2 package is a duplicate of a previous package

  ISAKMP: last reply reference

  ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3

  crypto_isakmp_process_block:src:212.37.17.43, dest:212.118.128.233 spt:4500 dpt:4500

  ISAKMP: phase 2 package is a duplicate of a previous package

  ISAKMP: last reply reference

  crypto_isakmp_process_block:src:213.210.211.82, dest:212.118.128.233 spt:500 dpt:500

  ISAKMP (0): processing NOTIFY payload Protocol 36136 1

  SPI 0, message ID = 287560609

  ISAMKP (0): DPD_R_U_THERE received from the peer 213.210.211.82

  ISAKMP (0): sending message 36137 NOTIFY 1 protocol

  to return to the State is IKMP_NO_ERR_NO_TRANSdebug

  ISAKMP (0): retransmission of the phase 1 (0)...

  Thank you

  Ismail

  Hello

  The debug version, it seems that the parameters are not same on devices:

  ISAKMP (0): atts are not acceptable. Next payload is 0

  Please check the settings of the Phase 2 and also make sure that you have PFS disabled Watchguard.

  * Please rate if helped.

  -Kanishka

• I have Firefox 12.0 installed and when I open Youtube and/or Gmail they detect that the browser is obsolete. Why is this happening?

  I have Firefox 12.0 installed and when I open Youtube and/or Gmail they detect that the browser is obsolete. Why is this happening?

  You have a pref general.useragent.override, which identifies you as a Firefox/4.0

  • Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; RV:1.8.1.16; .NET CLR 2.0.50727; ffco7) Gecko/20080702 Firefox/4.0

  See:

  • https://support.Mozilla.org/KB/finding+your+Firefox+version
  • https://support.Mozilla.org/KB/websites-incorrectly-report-Firefox-outdated-or-in
  • http://KB.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default

• Align the two signals and measure the Phase Shift

  Hello

  I do an experiment in which I use the NI USB-6221 DAQ card. The jury is able to make 250 k samples/second. I want to measure two voltages in a circuit and find the phase shift between them at frequencies between 1 and 10000. First I ouputted a wave sinusoidal frequency variable through the Commission and applied to a test circuit. Then I used the Board to measure the two tensions consecutively (thus reducing the maximum sampling frequency at 125 k). I used the signals align VI and measured the two phases and then calculates the phase shift (VI attached in Phase 1). It worked well for the test circuit I built in which the phase shift went way logarithmique.20 degrees ~84.5 degrees and then stabilized. At frequencies above 5 000 Hz phase shift must have remained constant, but it varies more or less 1 degree. When the phase shift is 84.5 degrees, present a degree of variability is not particularly explicit. When I asked my program on the circuit that I really wanted to measure, the phase shift went from-. 5 degrees up to about 1.2 degrees. The change in the values of phase shift at high frequencies (> 3000) was environ.2 degrees. Given the small phase shift, this variation is unacceptable. Now I tried to use a sequence to each blood individually (increase the maximum sampling frequency to 250 k) and then align the two signals and measure the phase of each shift. When I use align it and re - sample Express VI to realign the two signals, I get the message "error 20333 analysis: cannot align two waveforms with dt even if their samples are not clocked in phase." Is it possible to align two signals I describe here? I enclose the new VI as Phase 2

  Matthew,

  I think I have an idea for at least part of the problem.

  I took your program data and deleted stuff DAQ.  I have converted the Signal on the chart control and looked then what was going on with the signal analysis.

  The output of the Waveforms.vi line has two waveforms, like the entry.  However, arrays of Y in the two waveforms are empty!  It does not generate an error. After some head scratching, reading the help files and try things out, that's what I think is happening: the time t0 two input signals are 1,031 seconds apart. Since the wavefoms contains 1,000 seconds of data, there is no overlap and may not align them.

  I changed the t0 on two waveforms are the same, and it lines up.  The number of items in the tables is reduced by one. Then I increased the t0 of 0.1 seconds on the first element. The output had both greater than the entry by dt t0 t0 and the size of the arrays was 224998.  Reversing the t0 two elements shifts the phase in the opposite direction.

  What that tells me, is that you can not reliably align two waveforms which do not overlap.

  I suggest that you go to 2-channel data acquisition and that it accept the reduced sample rate.  You won't get the resolution you want, but you should be able to tell if something important happens.

  You may be able to improve the equivalent resolution by taking multiple steps with a slight phase shift. This is similar to the way that old oscilloscopes of sampling (analog) worked. Take a series of measures with the signal you are currently using.  The make enough average to minimize changes due to noise. Then pass the phase of the signal of excitement to an amount that is smaller than the resolution of phase of sampling rate and repeat the measurements.  Recall that I calculated that for a 5 kHz signal sampled at 125kHz, you get a sample every 14.4 degrees. If shift you the phase of 1 degree (to the point/mathematical simulation), you get a different set of samples for excitement.  They are always separated by 14.4 degrees.  Take another series of measures. Transfer phase another degree and repeat.  As long as your sampling clocks are stable enough so that frequency does not drift significantly (and it shouldn't with your equipment), you should be able to get near resolution of what you need.  The trade-off is that you need to perform more measurements and may need to keep track of the phase shifts between the various measures.

  Lynn

• NET Framework 2.0 and 3.5 updates detected repeatedly, KB2633880, KB2572073 and KB2518864

  It seems that I lived this same problem with Windows Update services month last in terms of detection repeatedly updates.  This time they appear as essential.  My computer on my wireless network is running Windows 7 64 bit Home Premium Edition, which does not show updates available at this time.  The problem is now on my XP - Pro, also running IE8.  The three current updates, KB2633880, KB2572073 and KB2518864 have installed three times since my troubleshooting steps to fix the Windows updates detection did not work.  I ran so far, the cleanup tool NET Frame and Safet Scanner from Microsoft, which withdrew a piece of malware.  This is getting monotonous!  Microsoft has a solution?

  Now that I have reinstalled 931125, this update does not reocurr under Windows Update.  So what I had to do was hide remaining ones I didn't install.  For now, until the next question, Windows Update seems to work normally.

• VirTool:Win32/obfuscator.AFX / Obfuscator.XZ and that it has been detected but not deleted... How can I get rid of him?

  I ran security Microsoft SCANNER and it says there: VirTool:Win32/obfuscator.AFX / Obfuscator.XZ and that it has been detected but not deleted... How can I get rid of him? I ran malwarebites and it sees nothing

  Hi winfrey,.

  ·         Which antivirus program is installed on the computer?

  I suggest that you download and install Microsoft Security Essentials to see if it helps.

  Anti-Malware, viruses, Spyware Protection | Microsoft Security Essentials

• BOOTLOADER UNLOCK BUT CCP and KNEW is also detect is the model of phone (Neo V)

  One of my friends unlocked bootloader on an informal basis. Now he custom ROM installation to sound and wish.

  The most remarkable thing is that CCP and is also the detection model of phone (Neo V). It is download official rome in SUS and the CCP.

  Additional after dialing * #* #7378423 #* #*... he gets... Bootloader unlock license says Yes.

  How is that possible?

  There are a few informal ways in which DRM files are not lost after unlocking the bootloader.

  But free informally is not that easy, you may brick your device at all times if something goes wrong

• I got a Apple Watch yesterday and since put in place and paired him and everything, but now I can not unlock it or look at anything on the watch because it won't let me.  Any ideas as to what is wrong or what I am doing wrong?

  I got a Apple Watch yesterday and since put in place and paired him and everything, but now I can not unlock it or look at anything on the watch because it won't let me.  Any ideas as to what is wrong or what I am doing wrong?

  Hello

  If you have not already done so, it could be that you want to configure your watch with these settings:

  -On your iPhone, in the application of Eve, go to: My Watch (tab) > General > detection of wrist - it lights up.

  -On your iPhone, in the application of Eve, go to: Watch My > password > code turn on (choose a password Simple or more complex).

  -Also on the password settings screen, select Unlock with iPhone.

  After putting on your wrist, your watch don't unlock then after whatever you do first: unlock your watch manually (by entering the access code) or unlock your iPhone.

  Then, it will remain unlocked (including when the screen is idle) until you remove it from your wrist. When you remove your watch, it locks automatically.

  More information:

  https://help.Apple.com/watch/#/apd748b87e2a

• My music is gone and the library.itl method did not work. Help, please!

  I realized that all the songs in my library disappeared, with the exception of those that I bought. I have read a few older threads on people who have this same problem after an update and tried the steps (detected the itunes library.itl file, renaming etc.), but it did not work.

  My music is all saved on my computer and an extra hard drive, but I have more than 20,000 songs and I need my playlists to my business events and the demo of sampling and that makes me desperate. Is there anyway that I can restore my itunes when everything was perfect without slipping literally 20,000 songs in itunes? not to mention those of CDs. thank you if it is not resolved I can cry really.

  You say that you have a backup of your music, but you also have a backup of your library files?  Your playlists are only in your file "itunes library".

  I kind of suspect that you may have not followed exactly the instructions. When you install an update the iTunes application puts a copy of your old library file in the previous record of libraries with a date added at the end.  It is essentially the only thing that has your playlists and a list of media in your media folder.  iTunes creates a library update, then he calls "iTunes Library.itl" If this update procedure is not successful (and in most cases, it is) you can restore it by going to the previous iTunes libraries folder and make a copy of the latest library here (by date, you can see), rename the file by removing everything except "iTunes Library.itl" and what to put in the main folder of iTunes.  Restart iTunes.  If that really, really does not then your recourse to use the library files backup copies you hopefully takes place before that you did any kind of update software on your computer.  It's triply critical if you use equipment on a professional basis because your business depends on.

  If necessary, you can work your way through the previous libraries although they will not be updated. Me realize also that what you see in iTunes is only a list of what is in the file of the library and if you return to a library very old media are still in the media folder, but are unknown to iTunes because they do not appear in the old file to the library.

• I would like to receive a notification on my Apple Watch and iPhone simultaneously the messages/IM; not one or the other.

  I would like to receive a notification on my Apple Watch and iPhone simultaneously the messages/IM; not one or the other.

  I understand that if my Apple Watch is unlocked (or on my wrist) incoming Message notifications will be displayed on my watch. This allows to bypass the notification on my iPhone for messages.  I would like to find a way for Message notifications to simultaneously alert me on my iPhone and Apple Watch.

  Thoughts?

  Hello

  If you disable the detection of wrist (on your iPhone, in the application of the watch, go to: Watch My > General > wrist detection), it will make all notification alerts to be delivered to both devices. However, you will not be able to benefit from features including screen Wake on wrist lift, Apple pay and one unblock after placing the watch on your wrist.

  If you want Apple to consider adding an option for notification alerts to be delivered for both devices regardless of the other settings, you can suggest here:

  https://www.Apple.com/feedback/watch.html

• Want a Smart Touch 23-065: I've upgraded to Windows 10 and now my bluetooth devices do not work

  I have a Smart Touch 23-065 envy that I have upgraded to Windows 10 and now my bluetooth devices do not work. They are detected, but not pair

  OK, line background peripheral bluetooth is not supported until the vendor provides a Windows 10 driver which is not yet and my never be available. Suppose if I want to use bluetooth, I'll have to get a usb adapter

• HP 8600 over Error Message: paper detected does not match format of paper or type selected.

  HP Officejet Pro 8600 more

  Windows XP Pro, Windows 7 Pro

  Error message: paper detected does not match format of paper or type selected

  This error message appears on the printer display panel any time a custom paper size has been set up in Word (or any other application) and the format of paper & type was inserted in the Officejet Pro 8600 paper tray.  This error is generated by the printer regardless the orietation or margins or paper size settings in the document to match the paper size in the paper tray.  When you press 'OK' on the printer display panel, the printer ejects paper correctly.  Because this printer lacks a manual bypass tray, the custom paper is always inserted in the Tray1 and is the only book in this tray 1.  It's a simple tray 8600 more.

  What I am doing wrong?

  Your help is greatly appreciated.

  Unfortunately, you cannot print on a paper size "undefined" with printers. While the functionality is available in word, our printers do not recognize that the sizes of the main paper (these changes according to the country sometimes).

  The reason for this is because undefined paper sizes open the printer and the print job to a certain number of risks, including jams paper or misaligned printing. This is why the function is no more on HP printers.

  I recommend to find a type of traditional paper which is close to the size you want to print on and select in the layout of the print job as a workaround for this problem.

  I hope this helps!