Nexus 5000 native FC disk array and tape library

Similar Questions

• groups of IP addresses are supported on Nexus-5000 and models down?

  Looking online, I see the ip address of the object-group is explicitly listed as

  supprted on Nexus 7000 but on other model documents command is confusing.

  For example, for Nexus-5000 references to IP address source/destination to refuse the order group objects exist in the documentation older versions of NX - OS 4.0 and 4.1 (with no explicit object-group command is listed in the same CLI reference) but in v5.x current source/destination shows no Group of IP addresses as available choice.

  Can one with access to the Nexus 5000 or 3000 check if the ip address of the object-group is an order valid on this platform?

  It seems full support (like on IOS), using the IP address groups was established in v6 NX - OS (which only works on platform 7000).

  There was also presented on the lower models?

  Thank you.

  Hi Alexandre

  This feature is not currently supported on N5k/N3k

  If you have specific requirements for this feature, please join your team has to describe your network design. And they will be able to help you.

  HTH,

  Alex

• Connectivity HP C7000 and Nexus 5000

  We spend our ESX servers in a rack mount environment at C7000 enclosures with blades. Can someone talk about compatibility box blade HP and Nexus 5000? The little that I find seems to suggest that this match may not be 100% ready for primetime.

  I have a HP Virtual Connect modules or exactly what FCoE lokks like with HP blades. Does anyone have more information on this specific vegetables or aware of this configuration, used successfully?

  There is full compatibility between the HP 7000 and the Cisco Nexus 5000.

  What you need to make sure if it is that you are up-to-date with all HP firmware and drivers Nic ESX.

  Take a look on my blog that goes into this in detail:

  http://www.wooditwork.com/2010/08/09/Flex-10-ESX-pre-requisites/

  http://www.wooditwork.com/2011/02/17/Flex-10-ESX-design-with-simplicity-and-scalability-part-1/

  http://www.wooditwork.com/2011/02/17/Flex-10-ESX-design-with-simplicity-and-scalability-part-2/

  http://www.wooditwork.com/2011/02/18/scripting-Flex-10-ESX-design-with-PowerCLI/

  http://www.wooditwork.com/2010/10/19/HP-Virtual-connect-for-the-Cisco-network-administrator/

• Frames in Nexus 5000

  Hello:

  We have 2 Nexus 5000 Switch with n5000 - uk9.5.0.3.N2.2.bin system image file.

  2 Nexus divided in 2 centres and directly connected.

  In each of the switches, there is an Oracle server. These Oracle servers are grouped and connected by a link of heartbeat.

  The Oracle administrator ask us to set up frames in the heart rate.

  How can I do this?

  Thank you!!!

  All you have to do is put this configuration on all your 5ks nexus:

  Switch (config) #type of policy-map network-qos jumbo

  Switch(config-pmap-NQ) #network-qos default class type class

  Switch(config-pmap-c-NQ) #mtu 9216

  Switch(config-pmap-c-NQ) #exit

  Switch(config-pmap-NQ) #exit

  Switch (config) #qos system

  Switch(config-sys-QoS) #jumbo qos network type of service-strategy

  This will allow wide global capacity jumbo frame.

  To check if it works, do a "show int eth x / y", if you see Configuring jumbo rising and packages are not walked on, his work.

  Also note that the mtu will not change on the interface itself, it's a global command, not an order "by interface. But it's ok, even if mtu 1500, says it can still accept frames if you have applied global config.

  Example:

  Ethernet1/1 is on the rise

  ...

  RX

  0 1221713 packages 2644 multicasts packets broadcast unicast packets

  packages of entry 1224357 91236171 bytes

  ---> 458 jumbo packets 0 packets of repression storm

  short frame overflow of data entry error 0 Giants 0 0 0 0 against the imbedding

  0 0 surveillance so to the bottom of the fall

  0 entry with dribble 0 rejection of entry

  Rx pause 0

• Using SNMP to monitor Cisco Nexus 5000

  Hello

  I would like to know what specific OID to use to monitor the following using SNMP on a Nexus 5000:

  -L' total CPU usage

  -Power supply status

  -Status of Fan chassis

  The Nexus is quite different from other devices Cisco - any help will be appreciated!

  CPU: oid to use is: 1.3.6.1.4.1.9.9.305.1.1.1 (cseSysCPUUtilization) is a part of the MIB:

  CISCO-SYSTEM-EXT-MIB

  It displays the value as a percentage of the processor.

  ME-TestBed-A (nxos) # display system resources

  Load average: 1 minute: 0.26 5 minutes: 0.41 15 minutes: 0.43

  Process: 393 1 total, running

  CPU States: inactive user of 1.0%, 4.0% of the kernel, 95.0%

  Memory usage: total 3634820K, 1728600K used, 1906220K free

  81256K buffers, 1037176K cache

  DHCP-171-69-89-49: ~ lulu-mbp$ snmpwalk - public - Cabarrus 2 c 172.25.180.5

  1.3.6.1.4.1.9.9.305.1.1.1

  SNMPv2-SMI::enterprises.9.9.305.1.1.1.0 = Gauge32 : 5

  As you can see, show sys resources indicates 95% idle, valuation is 5% cpu and the snmp poster value.

  -------------

  Power and Fans, it is fairly limited

  The cisco mib envmon is not yet supported on the 5K, looks like.

  This leaves us with the FRU mib: 1.3.6.1.4.1.9.9.117 ftp://ftp.cisco.com/pub/mibs/oid/CISCO-ENTITY-FRU-CONTROL-MIB.oid

  The index values will come from oid: entPhysicalTable)

  1.3.6.1.2.1.47.1.1.1) is part of the ENTITY-MIB

  DHCP-171-69-89-49: ~ lulu-mbp$ snmpwalk - public - Cabarrus 2 c 172.25.180.5

  1.3.6.1.4.1.9.9.117

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.1.470 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.1.1000470 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.2.470 = STRING : « CentiAmps @ 12V »

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.2.1000470 = STRING : « CentiAmps @

  12V.

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.3.470 = INTEGER : 4538

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.3.1000470 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.4.470 = INTEGER : 29

  SNMPv2-SMI::enterprises.9.9.117.1.1.1.1.4.1000470 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.22 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.23 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.470 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.1000022 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.1000470 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1.3000022 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.22 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.23 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.470 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.1000022 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.1000470 = INTEGER : 4

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.3000022 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.22 = ENTIER :-2910

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.23 = INTEGER : -83

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.470 = INTEGER : 29

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.1000022 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.1000470 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.3.3000022 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.1.3.0 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.1.22 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.1.23 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.1.1000022 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.1.3000022 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.2.22 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.2.23 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.2.1000022 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.2.3000022 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.3.22 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.3.23 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.3.1000022 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.3.3000022 = INTEGER : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.4.22 = Timeticks : 0:00:10.27 (1027)

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.4.23 = Timeticks : 0:01:25.20 (8520)

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.4.1000022 = Timeticks :

  (41634711) 4 days, 19:39:07.11

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.4.3000022 = Timeticks :

  (41634712) 4 days, 19:39:07.12

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.5.22 = Timeticks : (0) 0:00:00.00

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.5.23 = Timeticks : (0) 0:00:00.00

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.5.1000022 = Timeticks : (0)

  0:00:00.00

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.5.3000022 = Timeticks : (0)

  0:00:00.00

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.6.22 = « »

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.6.23 = « »

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.6.1000022 = « »

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.6.3000022 = « »

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.8.22 = Gauge32 : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.8.23 = Gauge32 : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.8.1000022 = Gauge32 : 0

  SNMPv2-SMI::enterprises.9.9.117.1.2.1.1.8.3000022 = Gauge32 : 0

  SNMPv2-SMI::enterprises.9.9.117.1.3.1.0 = ENTIER : 1

  SNMPv2-SMI::enterprises.9.9.117.1.4.1.1.1.534 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.4.1.1.1.535 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.4.1.1.1.536 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.4.1.1.1.537 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.10 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.22 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.23 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.149 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.214 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.215 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.278 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.279 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.342 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.343 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.470 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.534 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.535 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.536 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.537 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4950 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4951 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4952 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4953 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4954 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4955 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4956 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4957 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4958 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4959 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4960 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4961 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4962 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4963 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4964 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4965 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4966 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4967 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4968 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.4969 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5206 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5207 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5208 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5209 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5210 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5211 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5212 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.5213 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21590 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21591 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21592 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21593 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21594 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21595 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21596 = INTEGER : 2

  SNMPv2-SMI::enterprises.9.9.117.1.5.1.1.1.21602 = INTEGER : 2

  You can read in:

  FTP://FTP.Cisco.com/pub/MIBs/v1/Cisco-entity-FRU-control-MIB-V1SMI.my

  that means values integer by OID.

  Take for example (look at the file

  ( ftp://ftp.cisco.com/pub/mibs/oid/CISCO-ENTITY-FRU-CONTROL-MIB.oid)

  cefcFRUPowerOperStatus: 1.3.6.1.4.1.9.9.117.1.1.2.1.2 for one of the

  index:

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.22 = INTEGER : 2

  We now need to find 22-year-old:

  SNMPv2-SMI::mib-2.47.1.1.1.1.7.22 = STRING : « 20 port 10GE SFP + / superviseur

  in the Module fixed-1"

  That means now the INTEGER 2 from:

  SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2.22 = INTEGER : 2

  Lets look at: CISCO-ENTITY-FRU-CONTROL-MIB-V1SMI.my, section

  cefcFRUPowerOperStatus, if you are looking for in this file you will find: we (2),

  That measn this controller is actually turned on and powered.

• Configure ports on Nexus 5000/2000 for the grouping of network server adapters

  Hello

  I have two Nexus 5000 and Nexus two, 2000.  The 5000 s are peers of vpc.  I would like to connect my server with cluster NIC in a port on each 2000 and all have both be active.  Is this possible?  What are the steps?  I thought it should be this:

  CPR_NEXUS_5K01 (config) # int eth100/1/32

  CPR_NEXUS_5K01(Config-if) # channel - group 32

  CPR_NEXUS_5K01 (config) # int eth101/1/32

  CPR_NEXUS_5K01(Config-if) # channel - group 32

  on the Nexus two.

  Thank you, Jerry

• Nexus 5000 operating as a standalone FibreChannel Switch

  Hello world

  Does anyone know if the Nexus 5000 can be used as a standalone FibreChannel Switch? Which means I don't want to run NPV on this and connect it up to a MDS or a different type of switch FibreChannel. I'm looking to create a 'Pod' scenario. Where a few servers and a storage Bay would hang the 5K on a login F_Ports is local FLOGI DB and be able to use zoning and traffic went immediately from the 5K, etc etc? I know that 5 K is not a full blown fibre channel switch such that it has some limitations, but again I think to a "Pod" as scenario.

  If the script above won't work for some reason any using CF can achieve us with FCoE CNAs on servers & storage Bay?

  Finally, FC domain IDS how 5 K can cause?

  Sorry for the questions. I'm new to SAN switching at this stage.

  Thank you all!

  Yes, it works even FC code NX - OS like a switch MDS switch.

  You connect FC HBAS, ports SAN or FCoE CNAs to Nexus.

  However, you need to license storage.

  Nexus 5010 supports up to 8 4 G FC or FC G 6 8 ports with the expansion module

  Nexus 5020 supports up to 16 4 G FC or 12 8 G FC ports with the expansion module

  Nexus 5548UP supports up to ports FC 32 4 / 8G without the expansion module

  Nexus 5548UP supports up to 48 4 FC ports / 8G with the expansion module

  Nexus 5596UP supports up to 48 4 FC ports / 8G without the expansion module

  Nexus 5596UP supports up to 96 4 FC ports / 8G with the expansion module

• I would like to migrate from Aperture. What happens to my masters that are on a RAID array and then what should I do with my safe which is located on a separate drive please?

  I'm sorry, but I'm loud understand what happening to my master original RAW files, I keep offline on a RAID array and then what I do with my safe that, like all my photos modified? Sorry for this simple question, but would someone help please my lift the fog?

  Thank you

  Rob

  One of the major downfalls of Aperture is that it shows you where are your pictures. They always favored it as a feature (even as a ' new paradigm'), but it's not so wonderful when you need to do something about Apple never intended. Then, it sounds really like it led to you not knowing where your files or files that correspond to which elements of the UI opening. I suggest that you need to nail for yourself - images from Aperture to right click and choose Show in Finder, until you know where everything is.

  Otherwise, make sure you have plenty of available disk space, stop asking questions and just see what happens when you run plugin import LR with the options I suggested. It won't damage the opening.

• The distribution of applications and data between the disk SSD and HDD

  I recently installed an SSD in my Macbook Pro (late 2011) instead of the DVD player. I want to install OS X on it, by replacing the current OS X on the original hard disk, I will continue to use for storing files. How should I allocate its use in car? OS X and applications on the data files on the hard disk of 500 GB and SSD?

  The first series of instructions will partition and format the newly installed SSD disk then install OS X on it. The second block will help you configure OS X on the SSD with your data on the HARD drive.

  Clean Install of El Capitan on a new disc

  1. Restart the computer. Immediately after the chime, press Command + Option + R until a globe appears.
  2. The Utility Menu appears in 5 to 20 minutes. Be patient.
  3. Select disk utility, then click on the continue button.
  4. When loading disk utility, select the drive (generally, the entry Out-bumpy) in the list aside.
  5. Click the Partition tab in the main window of disk utility. A panel will fall.
  6. Set the GUID partition scheme.
  7. Define the type of Format Mac OS extended (journaled).
  8. Click on the apply button, then click the fact when it is active.
  9. Quit disk utility and re-enter the Utility Menu.
  10. Select reinstall OS X and click on the continue button.

  How to use an SSD with your HARD drive If you want to use an SSD as boot with your existing HARD disk drive, as the disk 'data', here is what you can do. After installing the SSD, you need to partition and format the SSD using disc utility disc. Then install OS X on the SSD. Once installed OSX boot from SSD. Startup disk preferences to set up the SSD as the boot volume. Open the preferences users and groups. Click the lock and authenticate you. Or CTRL - RIGHT click on your username account list in the sidebar and select Advanced Options in the context menu. You will see a field called "Home dir: ' on the far right, you will see an Edit button. Click on it. In the file dialog box, navigate to the location in house now located on the HARD disk (disk HARD/users/user_name /.) Select the folder, click the Open button. Restart the computer, as shown. When the computer starts, it will now use the home located on the HARD drive folder. Another more technical method involving the Terminal and the alias is discussed in depth here: using OS X with a SSD and HDD - Matt Gemmell configuration. It's my preferred approach because I can choose which records of the House, I want to on the HARD drive and I don't want to. For example, I like to keep Documents and library files on the SSD because I frequently access their content. Make sure that you keep the bootable system entirely on your HARD drive where you need it.

• Options, advanced, "there's no ' disk space and network"?

  I searched "how to compact the received messages on mozilla" the answer say ' options, advanced, and then click on 'network and disk space' it is NONE 'disk space and network"not anywhere on advanced settings, 'general' to all that. This is not the first time an answer to my question produces the same results, not on my computer.

  Are you running the latest thunderbird? Are these messages imap or pop?

• Today my Macbook Pro could not start.  He showed me the ban or no symbol.  I was able to access disk utility and run first aid on the SM0256G of SSD Apple media successfully.  Cannot start in normal/safe mode.  Should I delete/install so I can?

  MacBook Pro 13 '' end 2015.  256 GB SSD drive. El Capitan last version 10.11.4. I turned on the Macbook Pro and it could not start.  The progress bar with the Apple Logo would be present but would end not showing the symbol «»  I tried to boot mode safe - no go.  I have not reset PRAM help.  I was able to access disk utility and run successfully the first aid. No help. I was unable to restore two separate backup.  The utility show me backups however when I would go to the next screen and no backup is available.  Disk utility displays the SSD.  Can I erase the disc and download OS X install?  Thank you.

  At this point, there is no need to delete. A new copy of Mac OS X can be installed directly over the old copy. This process replaces the components of Mac OS X on a file by file basis and adds missing ones, there will be no major throwing away what anyone, unless there is a power failure.

  You have already run disk first aid.

  Now use mode of recovery (command + R to start) to "Re-install Mac OS X. It should install the latest revision of the main version that you ran last.

• I can't open my pictures folder. Error message says I don't have permission! I ran disk utility and found no errors. How this could have happened and how can I fix this problem? I'm the only user.

  Suddenly, I can longer open my pictures folder. I tried to move a picture to the folder to see what is happening and received an error message saying I was not allowed to display the contents of the folder and if I move the picture here, I won't be able to see. I ran disk utility and found no permissions error.

  How this could have happened and how can I fix this problem? I'm the only user. No one else has ever physical access to my computer. However, I sign up for Skyhub a few weeks ago and copied the contents of my Macbook it. Since then, a "Remote disk" icon on my hard drive. This would be part of the problem?

  Select it, choose get the information on the file menu, open the section sharing and permissions and give you access.

  (141083)

• My wife has an i5 to 2.3 GHz MacBook Pro early 2011 and it worked like a slug.  Ran disk utility and verified that the disk needs repair using recovery HD.  What does this lead and what is the risk of losing all the data is there?

  My wife has an i5 to 2.3 GHz MacBook Pro early 2011 and it worked like a slug.  Ran disk utility and verified that the disk needs repair using recovery HD.  What does this lead and what is the risk of losing all the data is there?

  Even if it is very slow, you must make a return upwards before the race "repair disk". The risk of data loss is minimal, but do it anyway: Save and run to repair the disk.

  As for what it implies - most of the time nothing more than simply sitting and waiting to do his thing.

• Backups taking over 130 GB of 160 GB, getting 'Startup Disk Full' and the computer does not. Help!

  I fight for free space on one of my older iMacs work and I am to the point that we cannot use it because the startup disk is full.  I've recently upgraded to Snow Leopard OSX Lion (10.7.5) so I could update our video editing software, Adobe Premier.

  We run all our video projects on external hard drives, which does not have the boot disk space and are always good on the erasure of files from the Recycle Bin, audio, photo and video so that they are not get bogged down.  About this Mac shows my 160 GB boot drive contains 8.87 GB Audio, 7.69 GB, 6,49 Photos GB movies, 6.58 GB Apps and a huge 129.34 GB of backups.  I have time Machine backed up on an external hard drive and can't seem to find out where these files are to be removed from the startup disk.

  Turn off time Machine and restart does not clear space.  I have even made the Terminal kill command no matter what auto backups, deleted device and old library version in iTunes, etc.  and I have no backup label appears when I bring up the screen of star wars of the time Machine. I went through so many stages and suggestions to get this machine working again.  I understand these backups are supposed to remove themselves automatically, but why are there still first place if I save on the outside?

  PS I'm not very computer savvy, but I know my way around.  Additional suggestions are appreciated - please let me know if I need to provide more information.

  http://www.howtogeek.com/212207/how-to-free-up-space-used-by-time-machines-local - backups on your mac.

• "Disk Creator" and update firmware on Equium A200-1V0

  Please forgive me if I'm missing something really obvious, but I can't find even if I need to update the firmware of my DVD burner.

  The doc readme says to start "Toshiba Disk Writer", and then select Audio CD - that should give me information on the disks required to decide if the firmware update is needed. I don't see any creator of disc on my satellite and selecting Properties on my DVD burner tells me it's a RUG * A DVD-RAM UJ-850 s ATA Device.

  There is no link whatever it is cited in the update of the firmware, wherever it should be a feature of TSST Corp.

  I had a few firmware updates and am unable to see even if they are needed. Any advice would be much appeciated

  Hello

  The update of the firmware are still on the European driver Toshiba page.
  If you find any updates to the firmware on the Toshiba page for you laptop, then an update of the firmware is not necessary!

  Equium A200-1V0 seems to belong to the series of PSAF5 and three updates of firmware for TS-L632, TS-L632P, TS-L632H CD/DVD drives. You can find these details more info

  If your CARPET * a DVD-RAM UJ-850 s doesn t need updates.