no alarm of the IPS

Similar Questions

• Palm alarms of the GER. It will trigger the alarm even if the ringer volume is silent?

  I just upgraded to Palm Pre.

  I work in an office environment in which we have our rings off, which usually means the week of work my ringer is off and I just have on vibrate so I can feel it in my pocket when a call or text comes in.

  With previous phones if you set the alarm, the alarm would still off and make it sound, even if the ringer is turned downwards.

  PRE alarm will always be sound or I'm going to increase the volume of the ringtone to the top every night before I go to bed?  My charger is my bed so hung up that the charger is not a problem.

  Yes always audible alarm if the mute button is on mute, unless the settings in the preferences of the "clock" is not to do so. Open the app clock, the menu drop-down, select Preferences, there is a new option added in one of the latest improvements. 'Ringer turn off' > 'Play the alarm even when' > 'YES '.

• How to trigger an alarm in the DSC module if, after alarming reactivation

  My application monitors a large number of tags.  I set up the user interface to allow the user to temporarily disable the alarm for some time.  For example, if someone opens the door to a freezer, then it closes, the label of the temperature goes into alarm.  Since we know why the alarm has occurred, the operator can deactivate the alarm for a couple of hours.  When the alarm is reactivated for this tag, if it is still in the range of alarm, he should be back in alarm.  The problem is that it is not.  Is there a way to programmatically alarm status?  I use also the alarms & events display component ActiveX to acknowledge alarms, so I prefer not to use the user defined alarms.  Any ideas would be greatly useful.

  Tom

  
  

• HP 2035N: need an alarm when the page is printed

  We have a HP 2035N that whenever he prints a page, an employee must enter the piece of paper and complete a task as soon as possible. Our environment is not all that loud, but often we do not hear the printer works. Y at - it an alarm in the printer we could light (I doubt it because I looked at throughout this manual), an accessory that we could add to the printer, or a network solution that would let us set an audible alarm or send an alert to a workstation? Something audible would be the best option. If this sin't possible with this network printer, is there another network printer that would have an alarm?

  Thank you all to think about my problem and offer solutions.

  im sorry to say this, but, there is no sound option for this printer. the only printers that support this feature are the HP Officejet pro jet ink 6000, 8600, 200.

• Alarm in the smartband talk app

  Is it possible to use the phone to reject the alarm set through the app to talk about smartband?
  If I set an alarm through the clock of the phone app, I can reject the phone or the band.

  So you're talking about smart wake up? It is true that for now you can reject only from the band.

  And also, you say that if you set the alarm with xperia, the band will only vibrate once? Because I've met the same.

• alarm when the phone is turned off

  I tried to keep an alarm with the phone turned off.

  But it dosent ring.

  is there any setting to change this

  Thank you

  New-generation devices are not able to do.

• The IPS log and monitoring

  Hi all
  

  
  

  A few queries on Cisco IPS. !!!

  1. who are the best tool to get the logs of cisco IPS?

  2 where or what directory Logs/events of Cisco are registered?

  3. I am able to see the newspaper today but not able to see beyond the newspaper? What are the possible causes?

  4. any free software tool that look for events and newspapers of cisco IPS?

  5 cisco IPS manager express is free software or we must only cisco customer account?

  
  

  For any kind of help... Thank you

  
  

  
  

  Jonathan

  1. you can use IME (IPS Manager Express) to display all events of your IPS.

  Here is the page of the EMI for your reference:

  http://www.Cisco.com/en/us/products/ps9610/index.html

  2. the logs on the device of the IPS itself has very little storage space and it wraps once the log is full, so if you have a large number of events triggered, you are only able to see the latest events.

  3. based on my description above.

  4 cisco IME - it's free (no additional license is required to use IME).

  5. as long as you have account ORC, you should be able to download the software of the EMI.

  I hope this helps.

• Failure of the IPS

  Hi all

  I am facing a problem when the IPS fails the entire network behind it is not not accessible.

  so, how can I check capacity of box two

  1-material bridging.

  2-software workaround.

  As far as I know, there is no HW diversion on the 4500. But you can use the software of derivation:

  http://www.Cisco.com/c/en/us/TD/docs/security/IPS/7-2/configuration/guide/IDM/idmguide72/idm_interfaces.html#pgfId-1169786

• Recommendation of the IPS

  Hi Netpros,

  I want to implement the IPS solution in our company as well as management software to manage mailboxes of the IPS. What is the latest version of the Cisco management software I have to deploy. It will be compatible with the ID?

  Thanks in advance.

  You can implement 2.3 VMS of Cisco who has the CiscoWorks Center for IDS sensors

  For more information, please visit http://www.cisco.com/en/US/partner/products/sw/cscowork/ps2330/products_qanda_item09186a008009253c.shtml

  It may be useful

  Franco Zamora

• Recover password of the IPS module (ASA)

  Dear experts,
   
  I have an ASA 5500 series with AIP SSM (IPS module), the username and password are lost.
   
  According to cisco portal, there are two approaches to recover the password:
  1 using the CLI command: hw-module module reset slot_number password;
  2. with the help of ASDM--> tools--> 'IPS password reset.
   
  Not sure whether the two commands to achieve the same result (retrieve password) or they may have different results (i.e. need to reset the module).
   
  The device is online, reset module is not privileged.
   
  After checking the information from the internet, it offers to reset the IPS module. Any problem will be produced if the IPS module is not reset?

  RDG
   
  Anita

  Hi Anita,.

  You can try using:

  HW-module module slot_number password reset

  Who will reset just the IPS to its default username/password:

  Cisco and cisco

  You can access the ASA CLI IPS:

  session 1

  Then type cisco and cisco (username/password)

  For example, you could add a new password.

  Don't forget to evaluate and select the right answer.

• Problem to run the IPS of ASDM

  Hi guys, I have an ASA 5520 ver 8.4 with a module AIP-SSM-40, when I finished the configuration, I can ping from ASA IPS module and the IPS module to ASA. I can ping IPS module to my PC and so on. the problem is when I try to launch the IDM (IPS tab) of the ASDM,

  This error message appears on the GUI. Error connecting to the sensor. Load sensor error. I have connected the interface of management of IP addresses to a switch, the ASA is connected to the same switch, and my PC is also connected to this switch, all in the same vlan.

  Can you help me on what can I do to solve it.

  Thank you.

  Hi Hugo,.

  Please see the following link

  https://supportforums.Cisco.com/thread/2092783

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00808908d5.shtml

  Kind regards

  Prashant

• The IPS with ASA5520 failover

  We have a pair of 5520 s defined as active / standby, the two have an AIP - SSM.

  These two AIP are set to automatic update, that the SIG files so this is not a problem, but what about detecting active? The primary IPS will have seen a lot of traffic that switching IPS is not how active rule sets is performed when the ASA switches to the rescue unit? Will I 'holes' in my security of lack of sets of rules?

  Hello

  The units of the IPS are completely independent and don't sync anything without additional aid (for example using the Manager of security or other).

  Given their auto-update is good, but you must also ensure that the config is replicated, so when you make a change on one that you have to remember not to make the same change on the other.

  Situation normal active IPS is transfer of traffic (and sleep mode sees nothing), but when they flipping the day before IPS is suddenly in the ASA active - he doesn't know that the other IP address is out of action, he sees just the traffic which it will inspect according to its configuration.

  HTH

  Andrew.

• The IPS software version

  Just got an ASA with a SSM - 20 module. I am trying to determine the latest revision of sensor for the IPS module software. V5.1 (7) E1 has a date of October 18, 2007 and the 3,0000 E1 version has a date June 28, 2007. Which is the latest version?

  6.x is the latest version. What you're talking about are simply patch levels. It is certainly possible that the versions 5.x and 6.x are both actively maintained (I was not paying much attention to 5.x since coming to 6.x). The press release or the patch 'most recent' is compared to the version of the software you are using. IOW, if 8,0000 E1 is released tomorrow, 3,0000 E1 is still the latest hotfix for customers running 6.x.

• The IPS Version update

  We use the ASA 5510 with AIP - SSM 10 IPS version 6.0 (3) E1 with a licensee agreement valid. Now, we want to update version IPS 1.0000 E2, is that the update is possible? If so guide me how and also guide me or provide the link how to make a previous backup.

  Yes, I just do the same thing. You will need to download the upgrade with the extension pkg (not the image file that I kept trying to do). The file is: IPS - K9 - 6.1 - 1 - E2.pkg under the security software, software updates.

  Link:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ips6

  Once you have this file, put it on an FTP server, or place the file on the local client that you use to connect to the IPS with IDM. You will need to go to the update of sensor in the IDM and either choose FTP or local update path and point to the file. Sensor recharges when it is made, but you don't won't restart ASA. It will take about 5 minutes, and then you should be able to reconnect to your sensor with IDM.

  Here is a useful link on the upgrade:

  http://www.Cisco.com/en/us/docs/security/IPS/6.1/Configuration/Guide/CLI/cli_system_images.html#wp1231089

  Here is a link to make a backup of the config:

  http://www.Cisco.com/en/us/docs/security/IPS/6.1/Configuration/Guide/CLI/cli_configuration_files.html#wp1033167

  I hope this helps!

  Jason

• IME for version 6.0 of the IPS

  Hi, iam using the module AIP-SSM-10 in ASA 5510.

  my version of the ips is: 6.0 (6) and I want to use ips manager express (IME). I tried with version 6.1.1 and 7.0.2 IME, but both are not supported for the current version of ips.

  1. Please tell me which IME support for ips 6.0 (6) version.

  2. how to level my ips 6.0 version to the current version or higher.

  Please send me url links.

  1. the EMI version 7.0.2 supports IPS version 6.0.6 according file following IME 7.0.2 Readme:

  http://www.Cisco.com/Web/software/282829584/28797/IME-7.0-2.Readme.txt

  Only the new features of the EMI, including monitoring console, dashboard and integrated configuration, health are supported only on the sensors running IPS version 6.1 or later. However, all the other features on IPS 6.0.6 is supported on IME 7.0.2.

  2. you can update the IP addresses directly to version 7.0.2 (E4) using the upgrade package: IPS-K9-7, 0-2 - E4.pkg

  Hope that helps.