No signal between monitor U2410 and XPS 430 Tower

Similar Questions

• No signal between Pavilion dv4 and TV with HDMI cable

  Hello

  I have a Pavilion dv4 and a Samsung Smart TV. Two days ago, I was enjoying happily successful between the two with a connection cable HDMI. Now, the connection no signal. Here are some facts:

  -The correct TV settings are selected.

  -I don't think it's a problem of cable, as the cable and TV connection to a different device port work.

  -When I shut down the computer and restart, the image of the start screen appears on the TV, but the computer screen is black. Then the TV goes black and the screen with my password. So, if I unplug and re - plug the HDMI cable, I get the error "no signal".

  -I am tired on the installation of plug-ins or drivers because the connection work successfully only two days ago (although I will say that there are updates installed between the last time that the connection was successful and now). But if this is what will fix the problem, then I'm game.

  I'd like opinions and advice. Thanks in advance.

  Hello

  I connect HDMI permanently to a screen (TV, IE) and I use the monitor 2 only. Everything turns on the external display.

  Kind regards.

• IdeaCentre K450 'no signal' with monitors (VGA and HDMI)

  I bought a K450 (of Jack online of lenovo, handed to nine) in December. I have an Acer H226HQL 21.5 "monitor at the same time and put in place all at once. I used the VGA cable to connect the monitor. Everything worked perfectly until a few weeks ago. I went to wake the computer and the screen remains black. I pressed the power button to turn off completely and turn it on again, 'no signal' stil on the monitor. I tried to use the HDMI cable with the acer and the old monitor of 8 years of my last office (with VGA cable) and still no signal. Checked the power strip, it works fine. I am at a loss!

  I ran updates on firmware for everything, including the graphics, when I put the computer. I would check on the firmware for the graphics card, but it is difficult to without a working screen. In addition, do not know if this is relevant at all, but it was running windows 8.1.

  Is there anything else I can do to fix this?

  Thank you!!

  In fact, I realized there are TWO VGA ports in the case of the computer and
  plugged into another one and it worked. Oops. No idea why HDMI cables
  did not work, however. I hope that you are able to get your problem solved!

• Is it possible to transmit a signal between an entry and an exit signal with out nothing to do

  Hi all

  I use a DAQ 6601 map

  I would take a simple digital signal input and go directly to an exit, until I get a different entry how I want to send my own signal to the output port.

  I have a small program that reads a signal and then sends a signal to the good times the bit I'm stuck with sends just the entry of a terminal to the exit of another terminal and change something.

  Thank you

  Make a writing which was read just there because nothing more than this: , you are going to have to explain what you're having a problem with.

• What is the difference between Foglight JavaEE and Foglight JMX monitoring?

  Hello

  I have a plan to monitor the 6.1.0.17 WebSphere Application Server (32 bit) and 7.0.0.5 (64-bit)

  But I understand not all Foglight for JavaEE and Foglight for JMX.

  Foglight for JavaEE or Foglight for JMX is able to monitor WebSphere?

  What is the difference between Foglight JavaEE and Foglight JMX monitoring?

  Thanks in advance

  Jeans

  Just to add to the excellent answers already posted.

  We have 2 agents which allows you to monitor Java:

  1. a JavaEE agent that runs inside the JAVA virtual machine and the information of both JMX and instrumentation.

  This Agent will give you JMX information like information of JVM (use of the bunch, son etc.), of the Application and server availability information and other information of JMX/PMI (connections pools, pools of ejb, servlets, jsp, JCA and more).

  Java EE & # 039agent also gives you information of the instrumentation - RFA count and response time, exceptional output and timeout information, distribution of queries (App/DB, component technology, server, application failure), object tracking, transaction flow and stransactional between servers and data sources) and ask traces (the ability to see the trees of the RFA at the method level to know where things are slow/stuck).

  2 JMX agent is running outside the JVM but can run on the same computer or on a remote computer, this agent requires access active, JMX. This agent gives you information JVM, availability server/applications, as well as some data as the application server published using JMX (pools of connections, JCA, EJB, servlets, etc.). The JMX agent also gives you the ability to see a list of the mbeans, get the data they expose (javaEE agent gets only a predefined list (same list that is used as a template for the application servers in the JMX agent)).

  Hope this helps

  Golan

• PC runs, but does not start. Monitor, keyboard and mouse with no signal.

  PC runs, but does not start. Monitor, keyboard and mouse with no signal. Pretty much. And when you want me to remove the battery of the bios, or whatever, it seems tight and hard to get out because it is surrounded by other elements.

  All fans work, the power/battery or anything that works I think that, since there is a fan on the right where it is and it seems to work. I remember what happens before, I don't know, but before that, there are many gels. This error below was made before all this happened, but I managed to run f8 and then run normally until it freezes again. Then, after that, it runs but does not start. No beeps etc. The best fans will have plenty of vouches and Bravo to wherever you like me to vouch or maybe send the great service that you provide to administrators if that's even possible, haha.

  Thanks in advance.

  "

  The file is possibly corrupted. The file header checksum does not match the checksum calculated. »

  It is a sign of a lack of food.  Looks like you have a desktop computer?

  Power supplies run about $50.  It is a rectangular box at the corner of the system in which the power supply will from the outside.  It's a pretty standard form in most of the PC and with a little investigation thorough replacements can be found.

  It is usually held in place by 4 screws and can be held in place with a spring clip.

  Most essential, is that you need to buy a replacement with the right number of straight plug forms to adapt to your PC.

  This seems more complicated than it really is and takes about 5 to 10 minutes to do the replacement.

  Look at the power output of the power supply failure and buy a new, more powerful.  New desktop PC usually come usually with a diet under size and what are the causes these failures is too strong a request for devices you have connected.  So, buy one with a higher power rating.  Usually about 500 Watts does the trick.

  If you do not feel upwards to this task, a technician should not charge you much like this.

• Monitor, alternating between automatic adjustment and volume 0

  I have a HP w2207h monitor. It is as the decrease in volume control button is stuck and select auto menu setting button are both blocked on constantly. I can get to the menu if I pressed for a while and catch a cycle where it is not constantly try o lower the volume. I'm sorry if things are spelled wrong in the middle of the page, but I do not see in the middle of my page. f I press and hold the menu I can do go to OSD lock screen that blocks a smaller amount of the screen. Any ideas on how to make this stop? It is only hung a HP Pavilion desktop that was purchased with it as a package. When I am able to select menu it scrolls continuously downard as if the lower volume button is depressed, but I can press the button and click.

  OK if I jam a clip in the volume up button it seems to cancel the low volume button and hold it just constant. No bike back from now on.

  Well that does not really solve it either.

  He started to cycle upward instead and change the video settings. Then when I removed it went all of following what he did before again. Volume to zero is displayed and then bike auto adjustment in progress again and again.

  Message edited by wrightme43 on 01/10/2009 18:31

  Somehow, the problem has to do with the HD input on the screen sheet.

  It will go all fuzzy, with digital static. If I put the HDMI on the PS3 in the CAP and then attach attach it to the monitor cable and pull just right to stop that and other issues.

  Basically a manufacturing defect which is a common problem with this monitor in my opinion. I am extraordinarily cautious with caps, has worked with sonar on nuclear submarines and I am certified as well, ESA bascly no ham handed. HP, I'm sure that designed a great product, but manufacturing leaves much to be desired.

  In any case, the solution was to put on the cord HD just against the monitor cord and which eliminates all problems and has worked well for weeks now with no other problems that the cat hit the cord and it goes right back to jump back, then with static and blurred.

• Qosmio G50 - 10I - no synchronization on TV between the picture and sound

  My problem is that there is no synchronization between the picture and sound (+ the sound is thin about 5 seconds +)
  When I watch TV on Windows Media Center on the Qosmio G50 - 10I

  I tried to change the settings in Windows Media Center, but some will escape.

  How to connect this TV to the G50?
  You use the HDMI cable that provides audio and video signal together at the same time or you connect the TV with two different cables (for audio & video signal)?

  Also check the settings in Realtek HD audio Manager located in the control panel. Here, you can change some sound effects for different outputs (digital speakers, HDMI) audio

  PS: Last but not least install codecs. I recommend a package called K-Lite Mega codec package

• move the Panel between monitors without losing data?

  I read here and here for help.  The best that I can deduct is to call SetSystemAttribute and change the ATTR_DEFAULT_MONITOR value before making a followed LoadPanel of a DisplayPanel.  Then to change the Panel of this monitor to the other, I have to call a DiscardPanel, then repeat the whole process.

  This changed with success my Panel of a second monitor.

  However, as soon as I throw the Panel, all the data control on this special group gets wiped.  So how do you change a monitor Panel to monitor without losing its data?

  According to the help:

  To open the panels on another monitor, call SetSystemAttribute to change the value of ATTR_DEFAULT_MONITOR before calling LoadPanel or DisplayPanel.

  I found is not exactly the case.  Repeat the call of the DisplayPanel just redraws the Panel.  Again, I must first close the Panel.  I tried a HidePanel instead, but it does not work.

  My group, I have a table of data.  I need it to stay resident while lighting the Panel between monitors.  Ideas?

  ElectroLund ha scritto:

  I think I'll just save me every row in the table and populates the table again after reloading of the Panel.

  It might be faster to duplicate control on a hidden side and duplicate and then again on the new main panel.

  (It is not an idea of mine: Luis gave him here)

• Serial RS232 between existing Instrument and reading software provider

  Hello.  I have an instrument with software supplier for the acquisition of data from the instrument to a PC through serial RS-232 communication.  I would like to acquire data in LabVIEW instead of via the provider software.  The seller has given virtually no support to help me find a way to communicate with the instrument - they offer only their software as the only solution.

  I'm trying to find a way that I can transfer data with provider software and basically understand the format of the communications and the commands that are required to send to the device.  Two things that seem like possibilities are:

  (1) use a type of "spyware" or "monitor" for serial ports to capture and display the communications that occur between the instrument and the PC/software.

  (2) connect the COM1 port, from my PC (by which the software provider would communicate) to COM1 port on my computer and the insrument for a 3rd COM port on my computure.  Use hyperterminal or LabVIEW to read it as the instrument and software try to pass each other by reading iteratively to a port and then in writing as to the other port.

  No one has tried this before?  Any suggestions on who could work or work better/easier, or any other ideas?  I don't even know the port required parameters (baud, etc.), so I need to guess at those if I tried option (2), above.  I've never used any software serial port "monitor" before, so I don't really know what to use or else it might work for option (1).

  Thank you.

  Hello

  As mentioned, Microsoft Portmon's looks like your best bet.  Here is a link to where it can be downloaded:

  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896644

• My office does not send signal to monitor

  HP Pavilion a6200t and Desktop HP vp17 monitor

  My office does not send signal to monitor. I use the monitor to another computer it works fine.

  Problem 3 months ago.
  I clean the inside of the desktop with the compressed air bottle.

  Very important, I clean the contacts of the RAM with a cloth of cotton soaked in 95% alcohol.

• PC to tv connection error "no signal - check the connections and the external device is turned."

  Original title: pc to tv connection

  I have an Acer Espire Vista 32bits. Connect to a Panasonic TC L32x30 HD TV. The TV has a 'PC' marked port that matches one VGA cable. I have the VGA end of the cable is connected to the TV. The other end is connected to the PC Tower via a DVI adapter to the port where was my monitor.
  TV output is set to "PC". I turned on my PC, the Acer (Bios) screen came. He then shows the block scroll bar. Just as Windows is about to light up, cutting signal. I never get to see my office. A message appears on the screen saying "no signal - check the connections and the external device is turned on."
  I had posted before saying that I had problems ranging from VGA to VGA. That's why I bought the DVI adapter to try another solution.
  I hope I made things clear enough for someone to help him.

  Hello Winston M,.
  I actually solved it. Went to the screen and chose. Connection just how I mentioned. second monitor, default Says. I then checked"Extend Desktop to this monitor.
  As I type this, I can see it on my TV screen.
  Thank you for taking the time to answer my question.
  Problem solved
  Ray

• Clean the concert of dual core 2.4 Install windows 7 Dell XPS 430, drivers RAID DO RAID the relationship.

  Clean the concert of dual core 2.4 Install windows 7 Dell XPS 430, drivers RAID DO RAID the relationship. Two 1 TB drives, WD Black Cavier. 1. I wanted to know if I should format the OS drive first, before installation or installation? 2 should I let a slave to data disc (data is stored) or remove the installation? and 3 if I don't have a RAID relationship do I need to install RAID drivers with the installation with USB?

  Hello

  I suggest you to refer to this link and check if it helps:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/need-steps-to-configure-RAID-1-in-Windows-7-OS/3ec151ee-213C-4D04-a0f4-1d8c7eb6c1f3

  It will be useful.

• between my computer and router wireless connection (vista, premiem windows 7, 64 bit)

  Hey I recently had problems with my connection Wireless between my computer and the router.
  Normally off during the night is not connected to my router or on the internet the next day.

  I have been in close contact to my isp provider and have received a new router and reset my wireless Internet services provider site but I'm still having problems. I have also updated my drivers for my wireless on my laptop Hp G62 and have found that it will not cut when I do not shut down or sleep during the night.

  When you try to solve the problem, it will come back with "problem with the adapter or wireless access point and then asked to disconnect the power to the router. After doing this it will be fine all day.
  I do also to turn a blackberry 9000 "BOLD" and see first thing in the morning if the wireless is connected or not.

  ask for help, here is my last option I have been through everything and had an expert look at my computer where he found nothing wrong with my computer or wireless set up settings.

  any help or advice would be great

  Hello

  1. do you have problems connecting with Windows 7 or Vista?
  2. you remember of any change to your computer before the problem?

  Make sure that there is no interference between your router and your computer. For example. Mobile phones, like the mobile signals could conflict with your router signals and therefore no connection to your computer.

  You can uninstall and reinstall the Device Manager wireless network card.
   
  To uninstall the wireless device manager,
   
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
   
  Pilots should settle automatically after the computer restarts.

   

  Now you can install the latest wireless drivers and check if this solves the problem.

• Not plugged into the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Original title: high speed HDMI does not.

  I plugin the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Hi lisa,

  Try these steps and check the result.
  Step 1: Manage audio devices
  a. Click Start and then click Control Panel.
  b. click hardware and sound.
  c. under sound, click on manage audio devices.
  d. click on the playback device you want to output sound. Right-click in the empty space and click on see the disabled devices to see other devices.
  e. Select the device and click on set as default and then click OK.

  See http://support.Microsoft.com/kb/953500

  Step 2: Graphics output to monitor
  a. right click on the desktop, click chart options.
  b. output to monitor.

  Step 3: Adjust graphics hardware acceleration
  a. open the screen resolution by clicking the Start button, Control Panel, and then, under appearance and personalization, click on adjust the screen resolution.
  b. click Advanced settings, click the Troubleshooting tab and then click on change settings.
  Note: Some video card drivers do not allow allows you to change the settings.
  c. move the hardware acceleration slider at different levels and check the result.

  Visit our Microsoft answers feedback Forum and let us know what you think.