notification when a vpn user connects or rear

Similar Questions

• Routing of a VPN from Site to site to remote VPN users

  Hello

  We have a site and remote vpn site configured in the same interface in ASA 5520 (software version 8.3). When the remote vpn users try to connect to the computers located at the far end of the site to site VPN, their request has failed. I tried No.-Nat between remote vpn IP private to the private IP address of remote site, also said the same split tunneling. I can't find even the tracert, ping has also expired.

  Is there any solution to make this live thing.

  Shankar.

  There are a few things that need to be added to make it work:

  (1) on the SAA where remote vpn users connect to, you must add "permit same-security-traffic intra-interface"

  (2) you mention that you have added the LAN of remote site-to-site in the list of split tunnel, so that's good.

  (3) on the SAA ending the vpn for remote access, you must also add the following text:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  (4) on the ASA site to remote site, you must add:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  -No - Nat: ip access list allow

• inside the user initiates the connection to the vpn user

  Hi, couldn't solve this problem:

  I have to the customer. A and B.

  Connected via VPN for remote access and the applied filter A

  B is inside the user connected inside interface with sec - lvl 100.

  For example,.

  Pings B A but without success

  B connect A, but without success

  I know of sec - lvl 100 all the conn is allowed and ASA allows a connection established to the rear. Why B is not allowed at a.

  (after adding the ACL to allow b to A, I've been successful)

  First of all, security levels don't matter when it comes to traffic-vpn - all traffic in both directions is allowed without restriction as long as sysopt-permit vpn connection is present in the config (default).

  Secondly, when you applied the filter-vpn functionality, ACL works for traffic in both directions, i.e. you explicitly allow traffic in both directions in this single ACL.

  These vpn filter ACL is a little special ACL, cause it is written from the perspective of the (client) remote site, but should include entries for both directions. You can take a look here (or elsewhere)) on how it works:

  http://popravak.WordPress.com/2011/11/05/Cisco-ASA-VPN-filter-as-i-see-it/

• Get 810 error message when you try to connect to the VPN using L2TP protocol

  Original title: L2TP will not let me connect.

  I am in Workstation 9 and in each virtual machine, I have an AD - DC (2K8R2Enterprise), CA and RRAS (2K8R2Enterprise) and my last vm is a win7 (they are all tests).  All are not updated, but the PPTP, IKEv2 work without problem.  The second server that has the CAs and RRAS is a member of the AD - DC server.  The Win7 is not on the domain and I have Win7 a client certificate.  I have ensured that the CA root of trust is in the user store and computer Trusted Root CA.  I have also ensured that the Win7 client certificate is in the user store and personal computer.  I get a 810 error message when I try to connect to the VPN using the L2TP protocol.  I have exhaustively studied this problem and I can't find a solution to this problem.  I also raise the functional level of the domain to 2K8R2.

  I think this should be a simple and easy solution, but where can I find the answer?
  Please help me.
  Thank you for your time.
  Allan.

  Hi Allan,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:

  http://social.technet.Microsoft.com/forums/en/category/w7itpro

  If you need any other assistance, let know us and we would be happy to help you.

• [AnyConnect] Disable the alert when VPN is connected

  Hello

  When a VPN connection is successful, the users get an alert with this message:

  "Security policies have been applied to your session, access to certain resources may be blocked. Your system administrator has provided the following information to help you understand and address security conditions. "

  Is it possible to disable this alert?

  Thank you

  Patrick

  Hmm, the bug said that he should be set at 8.4 (1). Please open a TAC case to get only more studied.

  Here's the bugID for your reference: CSCsi89994

  Unfortunately, there is not displayed, release notes, however, it is said 8.4 (1) is the fixed version.

• Send a message electronic alert message when user connections

  Does anyone know how to set up an alert for a notification e-mail when a user connects to the VMWare cluster?  We have specific users who have a specific role, but my management would like to keep under lock and key in the event where all admins to get hit by a bus, a plane crash, drown in a boating accident, etc. at the same time a user of emergency.  In order to ensure that this user is only used during the terrible events listed, I'd like to as notification out when this user logs on.  All those put up something like this?

  In vSphere, you can create a custom alert data center with a triggen on the user login.

  With old Server vCenter, you must find the table DB was connection (and other events) are stored and develop a DB trigger.

  André

• When I try to connect it to my sync account, he said that there is no such user.

  When I try to connect it to my sync account, he said that there is no such user. I don't want to save again, as this is a perverse way to the creation of duplicate accounts. I also have an account password file to keep track of user login data: user name, email address, password, so it's not a matter of just forget the name of account etc. I've just updated to 29 of Firefox, this could be a coincidence.

  I use windows 7, with the latest updates and patches.

  29 Firefox introduced a new synchronization mechanism. This new system has existed only for about 2 months, so it is likely that you have actually not account. You can see the information for the new synchronization here: synchronize bookmarks of Firefox, history, passwords and more.

• Loud fan and battery drain, when the second user or get connected.

  Hi guys, anyone knows it why the fan runs constantly and just when a second user or guest is recorded in the Macbook Air and are there patches for this problem? When I am connected, there is that no problem, the fan is quiet and the battery holds its charge!

  Consider the possibility of a conflict of third party software.  Maybe run EtreCheck to get an overview of your current state of the system.

• When I change how a user connects power on and off a screen appears saying "client for Netware has disabled the Welcome screen and the fast user switching. To restore these features...

  Original title: how to uninstall client services for netware?

  When I change how a user connects power on and off a screen appears saying "client for Netware has disabled the Welcome screen and the fast user switching. To restore these features, you must uninstall client services for Netware... But it is impossible to find... Help?

  Hello LindsayJune,

  Click the Start button.
  Click on Control Panel. Select network connections
  Right click on 'Connect to the Local network', then click 'properties '.
  Search for "Client Service for NetWare" slot "this connection uses the following items."
  Click it, and then click the "Uninstall" button
  Restart your computer.

  Uninstall client for Netware feature will allow the option of quick change of user on your computer.

  I hope this helps.

• I want to share folders on my xp pro sp3 PC. How can I configure it so that a login prompt appears when users connect to it as \\ip\shared... ?

  I want to share folders on my xp pro sp3 PC. How can I configure it so that a login prompt appears when users connect to it as \\ip\shared... ?

  Hi Kelvin,

  You can share a folder on your XP by the listed method: http://support.microsoft.com/kb/304040

  Others have an option to connect to your pc as a guest, to make interactive you will need to click on start-> run, type &-> gpedit.msc

  Navigate to Computer Configuration-> Windows settings-> Security-> Security Option settings. On the right side, look for-> ' access network: model sharing and security for local accounts "-> double click and select-> classic-Local user authenticate.

  Now another pc you can access this computer and you will be asked for the username and password.

  I hope this helps.

• my user account is locked when I go to connect, how can I unlock it? Sue

  my user account is locked when I go to connect, how can I unlock it?

  The power plan settings can tell the system to require a password to wake up from sleep as can the screen saver.

  It is what you are referring to or tell you that it does not meet you try to put your password in when you want to return system?

• User account fails - temporary profile load when you try to connect

  Hello

  I need help. Since today, I can not connect to my windows user account, an administrator account. When I start the computer, available user accounts (two) are correctly displayed with pictures profile, but when I try to connect to mine the log in procedure takes almost ten minutes and, eventually, windows cannot load my profile and gives me a temporary profile in place with just the default settings.

  How can I get my user account to the service? (Restarting the computer does not help, signing on the temporary account in order to login to my account does not work either.)

  Thanks in advance,

  Andreas

  OS: Windows 7, 32 bit, Home Premium

  In principle, 'Yes', as suggested by ITknowledge24, but after a few business mixed upward account names I'm not so confident. If it was my own machine, then I leave the account as it is. Alternatively, you can create a restore point before moving forward so that you have a backup path rewrites.

• Users of VPN cannot connect using application using port 3404

  VPN users are connecting using vpn tunnel to destination of a pix 515e however, they are unable to use the connection on port 3404 application. He used to work, or so I was told, but it no longer works. What I am doing wrong? Please notify. Here is the config:

  IP 192.168.0.3 - dealer 192.168.0.5 pool room

  IP pool local DYNAusers 192.168.1.2 - 192.168.1.20

  IP pool local DYNAusers2 192.168.1.21 - 192.168.1.254

  vpngroup address pool DYNAusers PCPVPN01

  vpngroup 192.168.x.x wins server PCPVPN01

  vpngroup PCPVPN01 DYNAsplit of split tunnel

  vpngroup idle 1800 PCPVPN01-time

  vpngroup password PCPVPN01

  vpngroup address pool DYNAusers WELLVPN01

  vpngroup 192.168.x.x wins server WELLVPN01

  vpngroup WELLVPN01 DYNAsplit of split tunnel

  vpngroup idle 1800 WELLVPN01-time

  vpngroup password WELLVPN01

  vpngroup address pool DYNAusers2 SRVCVPN01

  vpngroup 192.168.x.x wins server SRVCVPN01

  vpngroup SRVCVPN01 DYNAsplit of split tunnel

  vpngroup idle 1800 SRVCVPN01-time

  vpngroup password SRVCVPN01

  permit 192.168.1.0 ip access list DYNAsplit 255.255.255.0 192.168.0.0 255.255.25

  5.0

  permit access ip 192.168.0.0 list DYNAsplit 255.255.255.0 192.168.1.0 255.255.25

  5.0

  DYNAsplit list of allowed access host ip 209.42.50.82 192.168.1.0 255.255.255.0

  DYNAsplit ip access list allow any 192.168.0.0 255.255.255.0

  access-list DYNAacl 60 allowed ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0

  Permitted connection ipsec sysopt

  Answer sheet crypto ipsec transform-set esp-3des esp-md5-hmac Dynamics

  Crypto ipsec transform-set esp-3des esp-sha-hmac To_NHP

  Crypto-map dynamic DYNAmap 30 game of transformation-dynaset

  card crypto VPNtunnels 30-isakmp dynamic ipsec DYNAmap

  map VPNtunnels 40 ipsec-isakmp crypto

  crypto VPNtunnels 40 card matches the address 150

  card crypto VPNtunnels 40 set peer 70.151.5.114

  card crypto VPNtunnels 40 the transform-set To_NHP value

  card crypto vpntunnels 40 the duration value of security-association seconds 3600 KB

  s 4608000

  VPNtunnels interface card crypto outside

  partner-30 map ipsec-isakmp crypto

  ! Incomplete

  ISAKMP allows outside

  ISAKMP key address

  subnet mask 255.255.255.255

  ISAKMP nat-traversal 20

  part of pre authentication ISAKMP policy 30

  ISAKMP policy 30 3des encryption

  ISAKMP policy 30 md5 hash

  30 2 ISAKMP policy group

  ISAKMP duration strategy of life 30 86400

  part of pre authentication ISAKMP policy 40

  ISAKMP policy 40 3des encryption

  ISAKMP policy 40 sha hash

  40 2 ISAKMP policy group

  ISAKMP duration strategy of life 40 86400

  Hello

  It is good to hear that the problem has been resolved. Please note do you have for the job?

• DNS problems when VPN Client connection is Active

  Using the latest version of the Cisco VPN client. Support remote clients... when I VPN on client sites I lose connectivity to my local exchange server. The DNS client appears to become primary on a VPN connection, where he bring himself to the public address of our exchange server. In the Transport settings, I have "allow LAN access. Any help would be appreciated. Thank you.

  Whether or not the local lan access is allowed is a setting on the device remote, not only to your customer. To see if you get local lan access, look under the tab Details of statistics and the road.

• VPN disconnects when you switch users

  I use Windows 8 64-bit with two users. If I establish a PPTP VPN connection with a single user and then switch to another user (keeping the original logged-in user), the VPN is disconnected automatically.

  Is it possible to keep the VPN constantly connected? The computer is shared between employees who have their own office environments and disconnect the VPN cause all sorts of problems.

  Hello

  I suggest you to ask your question at the following link.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro

  I hope this helps.