Number of certificate to ACS secondary

Similar Questions

• Cannot save an ACS secondary for replication of ACS primary 5.2.

  Hello

  I hope someone can help me.  Currently, I have two devices Cisco ACS and both are classified in the PRIMARY.  The first ACS is running version 5.2.0.26 while the second ACS is running version 5.3.0.40.

  My original thought was to install the first ACS and do serve primary and have it replicate its data on the ACS SECONDARY.  Somehow, after installation, the ACS are now listed as PRIMARY.  When I go into secondary ACS under Deployment Options to try to save it in elementary school, I get the following error message:

  "This failure has occurred.  Failed to authenticate with node.  Your changes have not been saved. »

  Even if I try this GBA primary to save it for the secondary ACS, I get the same error message.  I tried all passwords including the credentials of the admin super user, my credentials for the administrator and the credentials provided to SSH in ' GBA and nothing is helping.

  Reading online, I read there was a way to remove an ACS secondary, but I don't have the ability to add this server in the primary for "bump it down" to a secondary antibody hoping to save it for the primary ACS.

  If anyone can give me some pointers, I would greatly appreciate.

  Thank you, and all have a wonderful day.

  THERE

  Yvonne,

  If the identifier is the same then definitely replication does not work, you will not be able to enroll in primary school if the license is the same. The good side is that you have the other license, you only need to install.

  However I have more bad news, the only way to re - install a license file in ACS 5.x uses the CLI command 'acs reset-config', but it will also delete all of the configuration that you have on this server, except the network configuration (IP, gateway, DNS, etc.)

  After entering this command if you are trying to access the GUI, you should not use the name of user and password acsadmin/default, then you will be asked to locate the license file.

  Here is a document with this information where you need it:

  http://www.Cisco.com/en/us/partner/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/my_wkspc.html#wp1052906

• ACS secondary server does not authenticate users through 3850 WLC

  HI - I have a question that my secondary ACS server does not authenticate users when the primary is taken offline.  My configuration is:

  3850 WLC by using the code version 03.07.00E

  ACS Version 5.6 (primary/secondary)

  The two ACS servers added to WLC (ACS-NLBP-01 (primary) / HEN-ACS-01 (secondary)), defined in the Group server (ACS_AUTH) and also the method list (ACS_AUTH).  List of the ACS_AUTH method is then applied to the SSID.

  A 'test of ACS_AUTH aaa server group' command for the two outcomes of ACS server as a result of access.  Communication IP/Radius is operational between WLC and two ACS servers.

  configuration of 3850 also attached for reference.

  Any help would be appreciated.

  Thank you

  Scott

  Please add the below listed orders and test again when you can.

  Server radius # deadtime $min$
  retransmission of radius-# 1 Server
  # Server radius-dead-criteria times 5 tent 1

  Configuring settings for all RADIUS servers

  HTH

  ~ Jousset

• FPS: Number of certificate HOST...

  Dear all,

  I have no doubt on the certificate of the host:

  I have two hosts different shows AIP - SSM module certificate value that I have installed/configured both on the same date.

  I'm not quite sure what this certificate to host... any1 could he understand me... and what is impect, if it does not...

  ASA active IPS:

  Valid certificate from the host: 12-Jan-2009 to January 13, 2011

  IPS standby ASA:

  Valid certificate from the host: 04-Jun-2009 to 5 June 2011

  Concerning

  Amar

  Amar;

  The host certificate is used to establish a secure communication between the sensor and the Manager of devices such as the IPS Manager Express, CS-MARS, etc.  It can be regenerated in the CLI by issuing:

  generate TLS keys

  It will be valid for two years from the date it was generated.

  Scott

• vROPS number of certificate trust remains Java API?

  PluRav helped me on my another discussion, but I decided to start a new discussion centered around server certificates. When I run this code:

  Customer customer = ClientConfig.builder () .serverUrl ("https://{ip} / api suite")

  .basicAuth ("user", "pass")

  . useJson()

  . Build()

  . newClient();

  
  Adapters AdapterInstancesInfoDto = client.adapterInstancesClient () .list ();

  I get two error messages:

  customer. HttpClientFactory - no verification of server certificates

  customer. RestTemplate - Get 'url' gave rise to 401 Unauthorized; citing the Manager error

  I think I should tell the code to trust the self-signed certificate, but I'm not sure how to do this.

  Any help would be appreciated.

  Try this, you now get any output?

  Public Shared Sub main (String [] args) {}

  try {}

  Customer customer = ClientConfig

  . Builder()

  .serverUrl ("https://123.45.67.89/suite-api")

  .basicAuth ("admin", "password")

  . Verify ("false")

  . useJson()

  . Build()

  . newClient();

  retrieve the list of all instances of the adapter

  AdapterInstancesInfoDto adapterInstances = client.adapterInstancesClient () .list ();

  get the real set of adapters

  Set of adapters = adapterInstances.getAdapterInstancesInfoDto ();

  Browse all

  for (AdapterInstanceInfoDto adapter: adapters) {}

  print on console

  System.out.println (ReflectionToStringBuilder.reflectionToString (adapter, ToStringStyle.MULTI_LINE_STYLE));

  }

  } catch (Exception e) {}

  e.printStackTrace ();

  }

  }

• Number of certificate when you upgrade to 2.0.1

  In our VIO environment I had to change the VC certificate earlier. To operate the VIO again, I added the new certificate to /etc/ssl/certs/ca-certificates.crt on the controller * and compute nodes. This works as expected.

  Now I would upgrade to 2.0.1 and it seems that, through this process, the installation routine replaces the etc/ssl/certs/ca-certificates.crt files, so it stops with an error. I could get around this with the addition of the VC certificate at the right time to /etc/ssl/certs/ca-certificates.crt (after that it gets replaced).

  It seems that a 'configure deployment viocli' don't even replace.

  So my question is: where on the administration server are the certificates that configuration process pushes towards the other nodes? I would set it at the root level, not that I run into this problem again.

  Thank you

  Daniel

  Hi Jun,

  Thank you for pointing me in the right direction. I could now implement the new certificate in the custom.yml:

  -convert the VC certificate: cat vc - cert.crt | Base64 w 0

  -Add this string in the file /opt/vmware/vio/custom/custom.yml: vcenter_certificate:... (see the Release Notes for VMware OpenStack integrated 2.0.1)

  -Run 'configure the deployment of viocli - v.

  Kind regards

  Dan

• I would check the number of certificate license CS5 8922688

  Dear Sir Madam,

  I'm at the end of tie after going through the licensing2.adobe.com and the chat session, but nothing helped.

  I hope you can help us. We are Global Yellow Pages Ltd.  This is regarding Adobe Design Premium CS5 that we bought the license of upsell Qty 5: IE EN Dreamweaver (65111999) and Qty 5: Flash pro/basic (65112151).

  Can confirm that we have 10 user license for the installation of the Adobe Design Premium CS5.5.5.5 MLP?

  Please come back,

  Mei

  Global Yellow Pages Limited

  Address: 1 Lorong 2 Toa Payoh Yellow Pages Building Singapore 319637

  Main line: 6356-8080. DID: 6351-1309.

  Website: www.yellowpages.com.sg

  Hello Mei,

  You should take a look at the Adobe database to see what is stored/recorded on your accounts. You will find general information on your account Adobe https://accounts.adobe.com/> see My productsView all the > these products are associated with your Adobe ID > name > serial number.

  [And to find your serial number have a look here http://helpx.adobe.com/x-productkb/global/find-serial-number.html > I've lost my serial number >] see comments.

  The last time Adobe suggests so too this activation https://helpx.adobe.com/contact.html?step=ZNA_downloading-installing-setting-up_licensing-.

  Hans-Günter

• Secondary ACS do not authenticate

  I have 2 ACS 1113 devices running 4.1 Build 24 (1). The first is the main and replica nightly on the secondary to our DR. Although in different places, they are both in the same VLAN with no. firewalls or an in-between of the lists to access them. All my devices will be authenticate with my primary ACS unless it is down, in which case they must authenticate the ACS secondary. The problem is that I have no problem with authentication on my ACS primary, but I can't get anything to authenticate to my high school (after the primary decision-making down to test). In trying to authenticate to my high school, I get no newspaper for authentication successful or failed after that my attempts fail. In addition, during my attempts fail, I try to log into devices locally and my authorization fails - again with no journal of the ACS. However, when I remove the NDG in the ACS secondary, I'm able to log on locally on the network device.

  I believe that with the device the NDG in the breast of the CSA, there is a communication omitting my attempts (although it does not connect anything) since I can take the device off that NDG and transmit local authentication. I was running code 4.0 with the same question and thought that the update should fix the problem... but obviously, I have something to do else here.

  Any comments or suggestions would be greatly appreciated.

  This on seconday acs.

  ACS---> configuration network ===> table Proxy Dis---> click default ===> if you see delivenrance 1 to the aaa Server---> drag it to 'Prior to'---> and what is there under forward to---> Drag it server aaa--> submit + apply.

  It should work now.

  If you do not see distribution proxy option then go to GBA--->---> advanced option interface configuration---> enable the distributed array.

  That should fix it.

  Kind regards

  ~ JG

  Note the useful messages

• Secondary ACS does not authenticate

  I install an ACS secondary, database replication works correctly.

  But when I try to use the ACS secondary server to authenticate the user, I can't authenticate successfully.

  In reports and activities (ACS secondary), it does not appear anything.

  In primary school, ACS, he failed attempts, I see an "unknown SIN" the ip address of the secondary ACS, it seems only secondary try to use elementary to authenticate...

  Where I'm wrong?

  Thank you

  Daniele

  Hi Daniele,

  It is because the parameter on the acs secondary proxy. On secondary acs visit acs--> configuration network--> table tell proxy---> bring your secondary acs under the front walk to the box.

  That should fix it.

  Kind regards

  ~ JG

  Note the useful messages

• Secondary ACS authenticates not to dynamic users

  Hi all

  I have two ACS server for windows with version 4.2. My problem is that, if the primary ACS server is down, dynamic users from the database windows in unable to authenticate with the ACS secondary. Please note that if a user is added to the ACS, this user can authenticate with the windows database. Only the dynamic mapping is not the case with the second ACS server.

  A quick response will be appreciated.

  What is in the database of Windows in both the points of the unknown user policy? Dynamic users are active under the unknown user policy?

  Are these servers ACS for Windows or the ACS SE with a Remote Agent installed on a member of the AD Server?

  If they are remote Agents, see the external database > Windows Configuration > selection of the Remote Agent. The same remote Agent is selected on both ACS servers?

  Please be aware that if you change the order of the RA he would remove all your group mappings.

• ACS 5.5 with EAP - TLS SHA 256 certificates

  Hi all

  Well, I just want to confirm that ACS 5.5 supports EAP - TLS with certificates SHA2.

  Thank you

  Manel

  Manel salvation,

  There was a time long deposited back enhancement to support EAP - TLS SHA 256 and obtained certificates fixed ACS 5.2 leave.

  CSCtd34175    Support for SHA2 certificates

  To answer your question, ACS 5.5 does support SHA2 certificates with eap - tls.

  ~ BR

  Jatin kone

  * Does the rate of useful messages *.

• 3.3 to 4.2 ACS server certificate

  Hi all

  We have activated the EAP - TLS authentication for wireless LAN user in our configuration of the network, and we have defined ever on our old server acs 3.3 third party CA. I want to use the same certifcate which is used in 3.3, how can I copy this certificate of 3.3 and get it installed on new CAs 4.2. what any condition must be met

  Hi Santosh,

  
  

  To export CA certificate from Windows version, do following :
  
  Goto
  [1] Start > Run > Type 'mmc' and hit enter.
  [2] Click on Console > Add/Remove Snap-in...
  [3] Click on Add > Certificate > Add > Computer Account > Next > Local Computer > Finish > Close > Ok
  [4] Expand Certificates > Expand Trusted Root Certificate Authority and select Certificates
  [5] Choose the ACS CA certificate, right click > All Tasks > Export > Next > Select 'Base-64 encoded X.509 (.CER)' > Next > Browse
  Choose the location to store, and give it a name.
  
  Press Next > Finish
  We should get a message 'export was successfull'
  Then Goto CS ACS solution engine
  System Configuration > ACS Certificate Setup > ACS Certificate Authority Setup > Click on 'Download CA certificate'
  Provide with the reuired information
  and uplaod the file by pressing 'Submit'
  Then Restart the ACS.
  And to use this certificate, goto
  System Configuration > ACS Certificate Setup > Edit Certificate Trust List,
  and check the ACS certificate being installed.
  then click Submit.
  Again Restart ACS.
  
  
  Regards,
  ~JG
  Do rate helpful posts

• ACS 5.3 join two different directories Active Directory without reply in the ad.

  Hello my name is Ivan:

  I have a question...

  Can join GBA 5.3 to two different Active Directory directories that are in two different networks for the use of eap peap mschap v 2, with 2 different certificates, to authenticate users in a wireless network?

  I have

  AD 1 in the newtork with Certification Authority 1 10.25.1.0/24

  AD 2 in the network 192.168.10.0/24 with Certification Authority 2

  There is no replicate in the 14:00 users in AD 1 are totally diferent from the AD 2.

  Both of their ad I want to join my ACS 5.3.

  How can I do?

  Thanks for your replies.

  Concerning

  Here are a few things we can think in your scenario.

  >            You cannot integrate the same ACS server directly to two different areas of AD (AD1, AD2). With ACS 5.3, all you can do, establish 2-way trust between domains (AD1, AD2). This way users of the area approved by ACS installed in the local domain can authenticate. You must add a UPN or the prefix NETBIOS suffix (e.g. [email protected] / * /-name) for the user name when is authenticating with a domain (Trusted one) that the ACS is not joined to, including child domains.

  >           However, with ACS 5.4, you can join the nodes of the same deployment GBA to different areas of the AD. However, each node can be attached to a single AD domain.

  ACS 5.4 primary - domain a.

  5.4 ACS secondary - domain B

  Release notes.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.4/release/notes/acs_54_rn.html#wp71092

  >            I'm not going to give an option to integrate ACS with LDAP as an identity database because LDAP does not support Peap Mschapv2 so any object of setting up the EAP authentication will fail.

  It will be useful.

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Re: Where could find my "Cerificate number"?

  I am trying to record my Toshiba laptop and the question is asked "Do you have a certificate No. Toshiba service? I wonder, can I find it on one of the information brochures or is this one of the numbers on the sticker under the laptop itself? If so, it is not labelled very clearly.

  It also frustrates me that the sticker indicates "Réf." but is also called a "model number" in some sections on this Web site. They should really stick to a single name to avoid confusion.

  Hello

  You use the page http://www.toshiba.eu/innovation/generic/services_warranty_reg_map_eu/ for the registration of the laptop?

  I can see on the first page, you are asked about the number of certificate. If you choose the YES option. Otherwise click NO and you won't be asked on this subject.

  When I bought my machine I didn t get it. I guess you don't have too much, but your option was YES, right?

• ACS RADIUS lost: 11051 RADIUS packet contains invalid state attribute

  Hi all

  We lack a very strange problem since a few days now. Our v5.2.0.26 ACS began to drop the connection of wired connections and wireless, with a message "RADIUS request to drop". The detailed message is: "ask RAY dropped: 11051 RADIUS packet contains invalid state attribute.

  This message is usually preceded by a ' RADIUS request dropped: 24444 Active Directory operation failed because of an error that is not specified in the ACS ' error.

  Communication with Active Directory seems to be ok, since workstations receive a valid ip address when it is connected to a non 802. 1 x switch (Cisco 4506) port.

  Any help grealty appreciated,

  Best regards and happy new year to all members,

  Laurent

  Hello Lawrence,.

  Please check the connectivity status of AD between the ACS and advertising on all of your ACS (secondary instances as appropriate) servers.

  Users and identity stores > external identity stores > Active Directory

  The connectivity status shows CONNECTED or DISCONNECTED on any of your ACS servers? If one of the servers is showing as DISCONNECTED, what could be the root cause of the problem.

  Hope that does you in the right direction.

  Kind regards.