Office sync with two Macs leads to duplicate the files/folders

Similar Questions

• VMware device with 2 network cards claiming the same IP address with two MAC addresses

  Hello.

  I see messages intermittent my gateway network two MAC addresses associated with a virtual machine running on a 5.5 ESXi host for the same IP address.

  The virtual machine is a MiTel 3300 controller for a VOIP system. the system is configured with two IP addresses, one on the local network and another with a public IP address in the DMZ. In the network configuration of the 3300, I assigned the address LAN IP at 00: 0C: 29:30:B2:B2 and the DMZ IP at 00: 0C: 29:30:B2:BC (Mac for network devices presented by the ESXi host virtual machine).

  On the host, I configured a vSwitch with exclusive access to two physical network adapters on the host machine. The vSwitch is configured with two machine virtual port groups, LAN and DMZ, with access to the physical network interface cards. Tab grouping of groups vSwitch port NIC, I replaced the order of failover of the switch to activate an active NETWORK card only for the Group of LAN ports and the other card NETWORK only for the DMZ port group. (I don't know how the content of the column of networks is determined. Neither is correct for the traffic on the physical switch. If these are configurable, please advise and I'll change the settings). The relevant parameters of vSwitch, groups of ports and VM are distinguished below.

  On the virtual machine itself, through the VMWare host, I assigned 00: 0C: 29:30:B2:B2 for the Group of LAN ports and 00: 0C: 29:30:B2:BC to the DMZ group port (best I can tell, anyway, since the MAC address field annoyingly obscures the last two digits of the MAC address - break if I invert the mapping) (, but all seems OK).

  The goal here is to make sure that MACs of ports vSwitch the 3300 is listening and sending always correspond to the physical ports that are VLAN Tag by the physical switch to ensure the routing. Generally speaking, it seems that what is happening but, intermittently, we cross one-way calls that suggests a problem of routing between us and our SIP trunk provider; coinciding with these incidents, I get an email along the lines of "the security in the network device has detected a conflict of IP address with two or more devices. The period of INVESTIGATION "DMZ. DMZ. DMZ. DMZ' is claimed by the following clients with MAC addresses: ' 00: 0C: 29:30:B2:B2' ' 00: 0C: 29:30:B2:BC'. »

  I did something in the configuration that would lead to this kind of collision intermittent? Have a hacked together a way to do something that could be accomplished in a way that is simpler and more reliable?

  Thanks for any idea that you can offer.

  Kind regards

  J.

  

  

  

  I probably don't fully understand your configuration, but it seems that you are not interested in using the collection of NETWORK adapters in the virtual switch of the VM MiTel 3300.

  If it is correct, why not create two virtual switches, each with a group of port (LAN and DMZ) unique and with a separate connection of (vmnic2 and vmnic1)?

  In general, collection of NETWORK adapters may be used to share traffic between uplinks and ensure that if one of the uplinks connect fails, a virtual machine still has access to the network.

• Adding a lock to a Note iCloud disables its ability to sync with a Mac

  My Mac is upgraded to El Capitan. Synchronization for notes has been works well between my iPhone and my Mac until today when I've upgraded to iOS 9.3. Creating a new note will sync perfectly, however, once the locking function is activated (locked or not), the note refuses to sync with my Mac. Does anyone else have this problem? Is there a quick fix or is this a bug with blocking of the Notes application?

  I thought about it. There was a new update that came out for OS X (10.11.4) at the same time that 9.3 is released for iOS (I didn't know this earlier). OS X 10.11.4 is necessary to properly synchronize with the 9.3 lock feature, if not disappears all note active locking.

  I would remove this issue, because it is no longer active, but I have no idea how to do...

• When my iPhone 5 syncs with my MacBook Air, it duplicates

  When my iPhone 5 syncs with my MacBook Air, it duplicates & 3 x photos that are already in the Photo app.  How to prevent this?

  You have the active library iCloud or photo stream my license?

  

• How I find myself with two passwords to iCloud for the same account?

  How I find myself with two passwords to iCloud for the same account?

  For security reasons, I only use iCloud for Contacts and "find my iPhone".

  Several months ago Apple forced me to change my password to iCloud.  So I did this.   In the last months, I used successfully the new password to 10 or 12 times when asked without problem.

  However, I received a notification of a software update for my Apple Watch. I did the update without problem. However, after completing the update my iPhone asked me to connect to my iCloud account. When I did this, she rejected my password. I made 4 attempts typing very slowly and with care for you sure I did it right.

  Then, operating under a hunch, I decided to enter my old password to iCloud. It worked?  I'm confused about this, any ideas would be appreciated.

  I had a similar problem last year. I had to call Apple. Contact is a bottom of this page.

• I want to move a large number of photos but don't want to unique, click each photo. I know there is a simple control function that allows to select groups of files with ' two'clicks ', as opposed to the selection of each file. Suggestions?

  I want to spend a lot of photos (they are in order) but and do not want to have to click to move each photo. I know there is a simple control function that allows to select groups of files with ' two'clicks ', as opposed to the selection of each file. Suggestions? I know it's apple 101, but I don't remember what order to press the button command, or shift, or other. Thank you

  Select the first file, then hold down the SHIFT key, and then click the last file. Or, select any file in the folder and then press command + A

• I have windows vista and when I click on a shortcut on the desktop I have a pop up asking what file to open it with. In order to open the file I find the actuall file.

  Original title: registry exe problem

  I have windows vista and when I click on a shortcut on the desktop I have a pop up asking what file to open it with. In order to open the file I find the actuall file. This also occurs when you download the software, which makes it difficult, because the file is not on the pc yet. All solutions?

  Looks like you may have a virus or other malware. Get your updated antivirus program and boot into Safe Mode. Note that some viruses can hide from your normal antivirus program, so you really need to scan in Safe Mode. To enter in Safe Mode when you turn on first, press F8 on every seconds until you get the menu, and then select Safe Mode. Then run a complete system scan.

  Microsoft has suggestions and offerings to

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-remove-a-computer-virus

  Moderator Forum Keith has a few suggestions along this line to

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-Explorer-has-stopped-working/6ab02526-5071-4DCC-895F-d90202bad8b3

  If that suits him fine. If this is not the case, use system restore to go back to an earlier date at the beginning of the problem. To run system restore, click Start-> programs-> Accessories-> System Tools-> system restore. Click on the box that says show more restore points.

  You can check the corrupted system files. Open an administrator command prompt and run SFC if the above does not help. Click START, and then type sfc in the search box, right-click to SFC. EXE and click run as administrator. Then, from the command prompt type sfc/scannow.

  Finally if all else fails, you can look at the rather cryptic system event log. To make, click Start-> Control Panel-> administration-> event viewer tools. Once in Event Viewer system log-click and scroll entries looking for these "error" with indicator see if you can find guidance on where the problem may be.

  I hope this helps. Good luck.

• When I try to install v.6, CD or as copied photoshop folder on the desktop, the installation stops with "Error1310-error to write to the file. Make sure you have access to this directory.

  When I try to install v.6, CD or as copied photoshop folder on the desktop, the installation stops with "Error1310-error to write to the file. Make sure you have access to this directory.

  Please see:

  Error "1310: error writing to the file: C:Config.Msi...» » | CS4 products

  I hope this helps.

  Greetings

  Megha Rawat

• problem with my mac pro book and the appstore

  I have a problem with my Mac Book Pro (2.53 ghz processor intel core duo / 0sx 10.6.8) and the app store:

  My apps no longer works after upgrade on the app store... Help :-(

  Restart in safe mode

  Try safe mode if your Mac does not end commissioning - Apple Support

  Once logged in go to the Terminal

  type

  Open $TMPDIR... me.

  Delete the folder

  com AppStore.Apple

  Close the terminal

  Open the App Store

• Sync/update of the files/folders

  I have some similar files are stored in two or more places different. Any suggestion, idea or script/code/batch to have similar as files:

  C:\Directory_A\File1.xlsx

  C:\Directory_B\File2.xlsx

  C:\Directory_C\File3.xlsx

  either the same be closed, given the other two compared to 'Change' and replace the other two with the updated version.

  Please note the different names of the files as well.

  Thanks in advance.

  Best regards, Faraz A Qureshi

  could try sync toy microsoft db·´¯'·.. ¸ >-))) º > ·´¯'·... ¸ >-))) º > share nirvana mann

• Guest VM Mac - IP address and the file copy host

  Hi all

  I'm involved with the automatic configuration of the guest virtual machines in Mac. In this context, I want to start and stop the virtual machine automatically. Also, I want to copy files between the host and the guest and launch programs automatically in the comments.

  -

  ---

  System details:

  VMware Fusion: Version 3.1.1 (282344)

  Host of Office Mac: OS X 10.5.8

  Comments to VMware Mac: OS X 10.6.2 Server 64-bit

  VMware Tools installed

  -

  ---

  1. I am able to use the vmrun as 'start', 'stop' commands, etc. But I'm unable to use the controls of the operating system called as 'runProgramInGuest' and 'copyFileFromHostToGuest '. I understand an exhaustive search, Mac Guest VM does support all the vmrun commands. Please specify if this isn't the case.

  2. because the vmrun commands do not work, and I always want to copy files to the guest, I try to get the IP of the host Mac address to connect to the FTP host - essentially treat them as 2 different machines on the network. Please specify whether it is possible to get the IP address of the Mac Guest VM and copy the files in the manner described.

  Thanks in advance,

  Hema

  Hi Hema,

  Welcome to the forums.

  I have no experience with the Fusion, but I had to work on the same problem with VMware Player. If your guest is using NAT network connection, you should be able to find its dynamic IP address in the DHCP leases file placed at:

  -/var/db/VMware/vmnet-dhcpd-vmnet8.leases

  As long as you know its mac address, you should find its IP address.

  It may be useful

  Concerning

  Franck

• dialog box "Choose the program you want to open this file" is displayed when I start (after shutdown or restart) with my windows username listed in the file to open

  As I mentioned, the dialog box appears after every restart.  It occurs after I entered my credentials to logon and proceeded to windows.  It seems to be pretty late in the boot process that things like the chat programs and widgets are fully charged at the time wherever the dialog box is displayed.

  The dialog box appears to be the 'Open with' dialog box in Windows 7 standard.

  Specifically the dialogue reads as follows:

  Choose the program you want to open this file:
   
  File: Mathew [it's my user id and he showed not extension)

  If I open the file into something like Notepad, then the information below is presented (the # s are real numbers, but these looked like mac addresses, so I left)

  ===========================================================================
  List of the interface
  ##...## ## ## ## ## ## ...... Dell Wireless 1510 Wireless-N WLAN Mini Card
  ##...## ## ## ## ## ## ...... NVIDIA nForce Networking Controller
  #........................... Software Loopback Interface 1
  #... # # # # # # # # Card Microsoft ISATAP
  #... # # # # # # # # Teredo Tunneling Pseudo-Interface
  #... # # # # # # # # Card Microsoft ISATAP #2
  ===========================================================================

  IPv4 routing table
  ===========================================================================
  Active routes:
  None
  Persistent routes:
  None

  IPv6 routing table
  ===========================================================================
  Active routes:
  None
  Persistent routes:
  None

  Startup in MSCONFIG includes:
  ArcoTray - request for assistance Adobe Acrobat Distiller
  Adobe Reader and Acrobat Manager
  AVG Internet Security
  CyberLink PowerDVD
  Dell Support Center updates
  Reference Dell Webcam Central
  Dell Wireless card wireless network tray Applet WLAND
  Google update
  GoogleTalk
  GrooveMonitor Utility
  Digital Imaging HP - hp all-in-one serious
  HpqSRmon Application
  hpwuSchd Application
  IDT Audio of PC
  iTunes
  Java platform
  Logitech SetPoint
  Microsoft Windows operating system
  Microsoft Windows operating system (Yes, it is listed twice)
  NVIDIA Compatible Windows7 Display driver
  Quicket
  QuickTime
  Synaptics Pointing Device Driver
  TranscodingService

  Samhrutha,

  I solved the problem.

  I found that when creating a new user, no longer had the open with dialog box.

  I started the process of resolution of a corrupted user profile (which seems little more than creating a new and copy and paste a few old values), when I decided to try one last thing.

  I logged on my account corrupted again and when the 'Open with' dialog that I open the file with Notepad.  I tried to "save under" to locate the file and found that it was located in C:\Users.  Something in recent weeks seems to have put a file without an extension, called "Mathew" (my log in name) in this folder, and it began when I started windows.

  I have since deleted the file and am no longer get the "Open with" dialog

  Thanks for your support!
  Carpet

• NEED TO MERGE TWO ADMINISTRATIVE ACCOUNTS AND ALL THE FILES IN XP - NO WINDOWS 7! CANNOT FIND TRANSFER IFTO ANYWHERE.

  I desperately need to merge two administrative accounts on my laptop - using XP and NOT windows 7 (so there is no transfer Assistant). I need to transfer all of the OLD admin. account in the NEW Admin account.

  For the full backup used Carbonite - due erase hard drive and reinstall XP - carbonite cust. veeeeery slooooow service and I had to use the laptop for the preparatory work.  When the backup has been restored, he implemented the administrative account of origin, besides I have created a new.  Now, most of the files are under the old administrative account, and I need to move the OLD files in the NEW Admin account.

  Would sincerely appreciate your very specific instructions? ... step by step, if possible? Not quite a prolific technician, but no slouch, not more.

  Thank you very much!

  You can't really merge two accounts. You can copy data from one account to the other. Folder options > view tab > check "Show hidden files". Then go to:

  c:\Documents and Settings\name of the old account and copy the files to My Documents, desktop, Favorites in folders in your new user account. When you have all your stuff, you can delete the old user account from the control panel > user accounts. MS - MVP - Elephant Boy computers - don't panic!

• Leader (?) "Not specified" and the files/folders missing

  I have a strange problem.  I had a folder with files and folders one couple with backups of these files.  Suddenly, everything that is found in this folder is titled 'No' icon and all other files and folders disappeared.  When I try to copy my files into this folder, it says the files already exist, but I showed you the hidden files and system.  When you click the icon not specified, it shows all files, including those located in the subfolders.  I can't move or copy this file (?) not specified.  What is this thing not specified and how to do things the way they were?

  Looks like you may have a virus or other malware. Get your updated antivirus program and boot into Safe Mode. Note that some viruses can hide from your normal antivirus program, so you really need to scan in Safe Mode. To enter in Safe Mode when you turn on first, press F8 on every seconds until you get the menu, and then select Safe Mode. Then run a complete system scan.

  Microsoft has suggestions and offerings to

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-remove-a-computer-virus

  Moderator Forum Keith has a few suggestions along this line to

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-Explorer-has-stopped-working/6ab02526-5071-4DCC-895F-d90202bad8b3

  If that suits him fine. If this is not the case, use system restore to go back to an earlier date at the beginning of the problem. To run system restore, click Start-> programs-> Accessories-> System Tools-> system restore. Click on the box that says show more restore points.

  You can check the corrupted system files. Open an administrator command prompt and run SFC if the above does not help. Click START, and then type sfc in the search box, right-click to SFC. EXE and click run as administrator. Then, from the command prompt type sfc/scannow.

  Finally if all else fails, you can look at the rather cryptic system event log. To make, click Start-> Control Panel-> administration-> event viewer tools. Once in Event Viewer system log-click and scroll entries looking for these "error" with indicator see if you can find guidance on where the problem may be.

  I hope this helps. Good luck.

• How know default ACM in my PC put in correspondence with another Podcast software for saving the file

  Hello

  I have a problem with the Windows ACM codecs as follows:

  I had bought a podcasting software and used perfectly for 1 year.  Now I can't use it to save the recorded files. I reported the error to this company for help. They asked me to download a tester and submit a report of my information system. Then, they advised me to download a LAME encoder file to add in the current software, but it does not help that the problem persists.  I found that when saving the file, the codecs of Windows ACM Deault I used to save before recorded files is not available.

  So please advise something wrong in my Windows Media Player and that I need to do to fix?

  Very much appreciated.

  Phan Phuong

  Phan chk this

  http://www.Microsoft.com/WinME/0506/24231/technet_fy06.XML

  or bing it

  http://www.bing.com/search?q=podcast+software+for+TechNet&form=IE8SRC