OfficeJet 4620 will not stay

Similar Questions

• OfficeJet 4620 will not print even though HP print and Scan doctor said that everything is Ok

  I just installed an OficeJet 4620.  I'm under Win 8.

  I printed out the status of the HP printer wizard pages.  They work very well.

  I ran printing HP and Scan Doctor v3.1 and all past.  However, when I try to print the test page, I get an error message saying cannot communicate with the printer.

  When I try to print from a different application, I get the same error.

  According to the Assistant of HP printer, the quality of the signal is a 4 (out of 5)

  Help

  Hi CallMeD,

  I suggest that you reset your network.  Click here to get instructions on resetting your network.

  Once you do this, I would set a static IP address for the printer.  Click here for more information on how to set a static IP address.  This link will be also other suggestions that may be useful.  Let me know how it goes.

  Good luck!

• Windows Vista SP2 fails to install and Windows Firewall will not stay

  Hello, I have problems with Vista 64-bit, it will not install service pack 2 and Windows Firewall will not stay. I tried to manually enable ICF manually and it won't turn. It gave me error 6x9D. I ran several antivirus scans malware byte and pc cleaner pro 2012 and the issue has not been resolved. If I could get help would be much appreciated. Thank you

  Hello

  What do you use for security?

  If you are using an Internet Security Suite, it will have its own firewall and disables the default Windows Firewall.

  And you should have only one firewall to avoid problems related to the operating system.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  You have not installed SP1?

  If so, try a direct download of SP2.

  Vista SP2 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=17669

  And if you have any problems:

  There is a Forum that Microsoft has put in place for problems with Vista Service Packs. If repost you the Forum they will definitely try to help you here...

  http://social.technet.Microsoft.com/forums/en/itprovistasp/threads

  See you soon.

• FreeCell card will not stay up

  When I play freecell, that my card will not stay up in the third blockit falls in can help you

  Hello

  -What version of Windows is installed on your computer?

  If you use Windows 7, follow the steps mentioned below and get back to us with the results.

  Uninstall and reinstall the game.

  a. Click Start, in the start search box type "appwiz.cpl" and press ENTER.

  b. click on turn Windows features on or off.

  c. clear the check mark before the games.

  d. click OK.

  e. restart the computer.

  f. re - turn on the device by placing a check mark before the games.

  g. restart the computer and check if the games to launch successfully.

  Reference:

  Turn on or off Windows features

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-features-on-or-off

  I hope that helps!

• My screen saver is set on various photos & first, they light up but they will not stay running

  Original title: screen saver

  My screen saver is set on various photos & first, they light up but they will not stay running, the screen goes black & I do not turn off my computer. I want pictures to be constinltly running.

  Hi mel merrill,.

  1 when was the last time it was working fine?

  2. did you of recent changes on the computer?

  3. you receive an error message?

  4. do the computer in sleep mode?

  Method 1

  See the link below and run them the fixit tool available, check if it works.

  Windows Photo and slideshow problems

  http://support.Microsoft.com/mats/windows_photo_and_slideshow_diag/

  Method 2

  If the previous step fails, then you need download and install the updated drivers for the graphics card on the computer by visiting the manufacturer's Web site.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Black vista Windows 2009! system will not stay running...

  my windows system will not stay running and shuts down my computer after maybe running for 10-15 minutes... says also download 3 of 3, but instead of blocking it loads windows and then I have no sound what either.  also used windows open sometimes it always ask if I want to run windows normally know, my computer was repaired and when I came back started all this junk, please if someone can help me send me an email to * address email is removed from the privacy *. and thank you for your help.  Oh yes, it keeps asking me for my windows vista black 2009 key that I do not have...

  Black of Vista is NOT supported by Microsoft.

  Go to where you downloaded from / got fix for support.

  Mick Murphy - Microsoft partner

• Removable shelf guard reset itself! Will not stay! Help!

  Hello

  I have a HP eStation 510a and the detachable tablet will not stay long enough to do something with it. As soon as it turns on it immediately turns off and then turns back on. I followed the steps to do a factory reset on it and successfully completed, but it still does the same thing. The printer itself works fine, it's just the tablet which is defective.

  Thanks for any help you can give me. It's driving me crazy!

  Hi mrsjermain,

  Welcome to the HP Support forums.  I understand that your the C510a zineb will not hold a charge long enough to turn on the Zeen.

  I have included a document troubleshooting when you have problems with the Zeen.

  The eStation, HP Zeen is Unresponsive, Blank or does not turn on

• My HP officejet 6500 will not print in colour without black. I tried to run the diagnostic, turning / of

  My HP officejet 6500 will not print in colour without black.  I tried to run diagnostics, turning on/off, changing the cartridge, mop up the cart - ink, withdrawal and the cartridges, printing a test page.  All to nothing does not.

  I continued to deepen the forum and found what was a soluntion for me.  I went to the configuration selected, then went to tools, it chose and then select printhead cleaning.  The first time that he clean the printhead, I only got six rectangles colored at the bottom of the test page printed.  My screen then asked if I wanted to get another clean process and I said YES.  Low and behold, the test print page not only the FCMA out with 6 colored rectangles but also tons of alphabets in black.  Hooray! His works again.  Hope this works for you.

• date and time clock will not stay set gose back to 1999

  time, back gose to 1999 after I have so far for 2012 will not stay this is why?

  I posted when there is no answer here, so I don't think mine is a double post.

• My Officejet 7410 will not longer accept WPA2 network access

  My Officejet 7410 will not longer accept WPA2 network access. He's always worked with WPA2, but after using the temporary printer with USB attached the printer wouldn't connect more after unplugging the USB. The only way to connect wirelessly is using WPA. What is the cause of this problem who can and how can it be resolved?

  Well, since you can't access your router to make changes, the only thing I can say now is take the device to a friends house and attempt to connect to access to the router for the tests.

• my logo will not stay in the corner

  In the Loo Loo model will not stay my logo in the upper left corner.  When it is in the design phase, it is there, but when I saw it, he puts it as close to the middle in the middle of my background image.  Any advice?

  Hello

  Please make sure that logo is pinned at the top of the page to the left as shown in the screenshot below.

  

  Concerning

  Vivek

• OfficeJet 4620 - will be not printed black - HELP!

  I have an Officejet 4620 and the printer doesn't print black ink.  Other colors print fine.  After spending $ 65, I've replaced the ink cartridges, and it would not print!

  I found the link to ""printer prints a blank Page or print no black or color ink for HP Officejet 4610, 4620, Deskjet Ink Advantage 4610 and 4620 e - all-in - One Printer Series " and followed all the instructions, TWICE, if not three times! "

  I also cleaned the printhead several times, two rounds each, and again, it will not be printed.  What to do is print the calibration reports that continue to eat my ink!   Printing reports colored pieces, but nothing in BLACK!

  This seems to be a very common problem with these printers because I have read several forums that describes the same thing, and HP does not seem a good solution or offer of difficulty or the problem.  I noticed most positions with this question end up making a private offline message.

  Before I wonder, the printer is no longer under warranty and I live in the United States.  PLEASE HELP ME!

  Hi @VetteGuy,

  Welcome to the HP Forums!

  As you have provided all the relevant information, I need to give a hand, I'll go and send you a private message to discuss the next step from here. If you are unsure how to check your messages on the forum this post, has instructions

• My Officejet 4620 do not print black ink

  I replaced the black cartridge on my Officejet 4620 with a new high-capacity HP cartridge and it won't print black ink on the test page, any application or function of Copier.  I have reset the printer nothing helps.  The ink level indicates that it recognizes the new cartridge and says it's full.  Black ink out of the cartridge when I put my finger against the exit hole.  I cleaned and aligned the print heads, but still no go.

  just in case someone else has this problem, heres whats really past and heres how to fix this annoying problem. its relatively easy to do and more efficient than wasting money on a new printer or have that he repaired as most people eventually do.

  going on what? the ink has clogged print heads and solidifies closed. the function of "clean print heads" the printer comes with doesn't have the ability to solve this problem. This feature is to clean the heads Sales, not clogged heads. Why hp decided to make this model without a simple to remove the cradle is beyond me, but fortunately the cradle out and can be cleaned with hot water.

  theres a few items, you will need to get there easily, or you could just burst the branch loppers, like I did and vent your frustrations.

  you will need: a pair of slender beak pliers, a screwdriver torx T9 (selling auto parts stores them for a few dollars), paper towels and a space for work (its easier to do this in a corner of a room, on a small table or floor).  Keep in mind that you are dealing with ink, then change your clothes right just in case and also catch a paper plate or a few sheets of paper to print to set ink cartridges while you work.

  (1) ok. lets start. !!! FIRST UNPLUG THE PRINTER RIGHT NOW, IF YOU DO NOT ACCIDENTALLY DIE BY ELECTROCUTION!  I forgot and when I started unscrewing the first 6 screws, kept chime jump and im like * beep *? I was impressed by the security measures hp took as model engineering.

  (2) the printer is now disconnected and then go to your corner your work surface and place the printer, so there is a wall or a barrier on the left, and also, a wall or a fence behind it. This just in front of her as if you were about to use it.

  (3) now, what you have to do, is to open the printer as you will change the ink and on the right side, there is a plastic guide that prevents opening all the way to the top. Look on the side and you'll notice that he could jump off with fingers. pop off and open it completely open, so you can get to the screws of the cover you would have prevented access to.

  (4) press the scanner part and the upper part against the back wall.

  (5) all the screws you will be remove are the size T9H torx screws. There are ten total. There are 2 black screws in the top of the forehead and then 4 black screws in the top of the back. Remove them and put them on your paper plate.

  (6) following is 1 screw silver short located under the Control Panel, use your finger and feel under the * button. Unscrew, place it on the paper plate.

  (7) depending on whether you want to remove the face/Control Panel to get in the last 3 screws so locate the illustrations on the top of the printer, there are 2 on the lower left and 5 at the bottom right (1 and 2 on the left explain removals of paper jam and 1-5 on the right then explain change in ink cartridges). then about half an inch South of the illustration of the number 5 on the lip, is a plastic stand. six inches to the left is an another then 6 inches to the left, under the number of the illustration 2 (remove the paper jam) is a third support. Unscrew using your nails. Flip it up just like the hood of the car, and eten on the main top of the printer, keep the flat wire which is connected to the frame of the control panel (if the flat wire jumped because you got too loud, then simply insert it in when you go back).

  (8) then unscrew the 3 long silver screws that are located under the Panel you just popped off the coast. There is 1 on the left and 2 on the side rightish. mix 'em on the paper plate.

  (9) now that all the screws are removed, take the Panel front and partially pop it back together.

  (10) then take all over (the part with the small illustrations and lift like a hood of car, ONLY THIS TIME OPEN IT LEFT and he balanced on the edge of the printer, to lean over towards the wall or an obstacle on your left.) MAKE SURE NOT TO PULL ON THE STRIP OF COLORFUL SON FRUITS LEFT AND ALSO THE FLAT BLACK WIRE CONNECTING PART SCANNING FOR THE MAIN OF THE PRINTER PART.

  (11) then take the pliers to tapered spout and remove the 2 silver tension springs located behind the printer cartridges. Pay attention to where they were attached so you remember where they go during the Assembly. take a picture with your phone if you have to, or simply re - understand it like I did. mix 'em on the paper plate.

  (12) then disconnect the 2 large flat wire and 1 small flatwire attached to the back of the ink cart. take a picture or can remember like I did. I guess bad things can happen if you reverse the on re-Assembly. Pick up the phone and take a picture of quik to be sure.

  (13) now remove the cart ink, cartridges and all, by lifting the front first.  Be careful of the transparent tape little there that moves the carriage from left to right and vice versa. you don't want to damage this little guy. now take the transport to your paper plate. not some ink or accidentally get it on your fingers without knowing or will make a mess.

  (14) remove the ink cartridges and put them on the paper plate, side ink to avoid a mess, these things sometimes drip. put the plate side. its time to clean the print heads.

  (15) then go to the sink, to the distribution of empty ink and turn on the hot water and then let the transport of empty ink sitting there with the water mainly through the clogged color screen (inspect and make you is not a small rubber seal surrounding the small screen, if there is do not waste it. I didn't look too closely and I don't think that hp has them but I have a few other printers). It will stain the sink but water ink he comes out to be sure. notice there is also a small circuit attached to it. don't bang it upward but getting wet does not matter.

  (16) continue to do this until the water is clear.

  (17) then use your finger and rub the screen gently with your finger and then rinse it, taking ink until the water is clear. This continues until there is no more ink and screens are clean. do it for all the colors just for good measures. the color of problem that would not print, you'll notice takes longer to clean than the other colors.

  (18) now look on the lower side of the transport. these strange looking things are the leaders. Rinse in hot water and dry them with paper towels. then flip it over and the breath on the side of the screen again. also between the screenside and heads (on the side of the transport) is an opening which is also probably gunked up. It blows with water too. Then, turn it over and wipe the head again. Repeat this step until no fades or until you are sick and tired.

  (19) shake, then use paper towels to dry the entire unit. Make sure that the device is dry.  especially inside the female plugs. blow inside or out dry hair and dry gently. do not stand there and melt the but with the blow dryer. but the sooner it dries less your ink cartridges, sitting on the paper plate will dry out. the custom of the ink dry quickly just do not take a NAP or go on a date until you're back with part of the ink.

  (20) now you have finished cleaning the heads and probably don't need to do it again for the length of time, it was because you bought the printer. and just as a roadtrip you used a map to navigate, you will use these instructions in reverse for reassembly. but keep in mind when re - insert the 3 flatwires that you disconnected from the back of the ink cart, make sure you that have small metal contact on the flatwires points (side male) inserted so they affect small metal contact points on the caps of transport (feminine) side. ALSO BE VERY CAREFUL NOT TO DAMAGE BLACK FLATWIRE CONNECTING THE SCANNER PART PART HAND PRINTER. THERE IS A SMALL GROOVE IN THE PLASTIC WHERE IT CAN SIT TO GUARANTEE NO CRIMPAGE. USE IT. also make sure that the 2 hinges to the scanner portion/cover are placed correctly before the fixing of the top with the 6 black screws.

  now raise the printer and reinstall the ink cartridges. then plug in the appliance and turn it on.  If you get notifications on the control panel telling the custom of transport move, then open the trunk and remove the ink cartridges, hustles and ensure that transport is installed and that the tensioner springs are in place correctly. Repeat the operation if necessary until notifications go away or just do a test print and do not take into account the notification if you messed with it a few times already. That's what happened to me and the notification went his own. Once its online, open the hp utility and press the button "clean the heads. do 2 x in a row and you will be in style, with colors extremely rich and "BOLD" and Yes, printed black raven.

  p. s.

  You can always take your aggression out with tree limb loppers or Tin shears like I did and cut the plastic Center keeps you to transport directly outside. Completely eliminates the disassembly and reassembly. Make sure you DO NOT CUT THE TRANSPARENT TAPE THAT MOVES BACK AND FORTH TRANSPORT. This way the next time it happens it takes you only 10 minutes before you are upward and printing.

  Enjoy!  -Porf

• iPhone will not stay connected to the internet?

  * Posted on MacRumors forums but no answers *.

  So basically since a few days my phone sometimes don't remain not connected to the internet network of BT-Hub3. I connect to it and then sometimes, it will stay connected for a minute for a few seconds and then disconnect. When I go to the wifi thing it seems available to connect to. After a couple of times that to happen, it will say wrong password (this is the password) and disconnect me and then I have to type the password. Repeat to infinity. It's honestly so frustrating.

  Sometimes it will stay and be fine but his is happened twice in the last few days and never happened before with any phone I've had.

  I try my phone with my BT-Hub4 internet network and it will stay connected. The only problem with this is that the internet is further (bottom), so has a low connection that does not charge anything unless I lean on my bed.

  Initially, I assumed my internet pick, but I'm typing this I am connected to the network BT-Hub3 without disconnect him, even once.

  I had the phone for a year and 2 months (previous owner had since October/November/December in the year of release) and recently got a replacement of the unofficial battery if this of any help. I also still have my phone on the low power mode. The phone always properly connect to the BT-Hub3 network even with unofficial battery and low power however mode.

  I had several other problems with the phone (camera, apps download not heat no reason apparent, random battery drains despite the new battery in just 3 months and has the same problem with the battery, slow Touch ID that apparently is not normal), which most recently happened.

  I had all the settings to reset a week or two ago but surely if who messed with my settings internet I would have had the internet issue earlier? Not sure if I should try to reset the network settings. I hate this and only do if I need to.

  One last note, I have the latest version of iOS so ignore saying his 9.3.2 on

  Hi pinkdolphins0400,

  Thanks for posting in the communities of Support from Apple! I understand that you are having problems with your iPhone does not stay connected to your internet connection at home. I use my home Wi - Fi network to stay connected, so I use all the cell data, if I can understand wanting to make sure that you are able to stay in touch. I am pleased to provide you with a few suggestions for you.

  The first thing I recommend you do is follow the steps described in the following article. It seems that you have already experienced some of these steps, but I want to be sure that you have covered everything.

  If your iPhone, iPad or iPod touch connects to a Wi - Fi network

  Since you mentioned that your iPhone will stay connected to your network to another, you can take a look at the network settings for the one that you are having problems staying connected to. Article below provides information about network configurations suggested for Apple devices. You can also check with the manufacturer for your BT 3 - Hub see if there are updates that must be performed. This can cause problems with disconnects.

  Recommended settings for the WiFi routers and access points

  For other problems you mentioned (apps do not download, camera, battery draining, contact ID, etc.) reset settings was a big step in troubleshooting to try. If these things are always happening, I recommend making a backup of your iPhone and then restore it via iTunes. The backup will ensure that your data is saved. When you perform the restore via iTunes, you'll want to set up as a new device (temporarily), and then test it. Once you test, you can try to restore your backup. You can find all of the information below, you will need.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Restore your iPhone, iPad or iPod touch from a backup

  See you soon!

• OfficeJet 6600: officejet 6600 will not analyze several pages to 1 pdf file

  Anyone got a fix for this pathetic...?

  Why HP would release a product that will not scan multiple pages into one file?  Pretty basic functionality.

  Hello

  Which can be configured from the HP scanning software.

  Software HP Officejet 6600 press on scan a document or Photo.

  Select the PDF shortcut, and then click the advanced settings link.

  On the file tab, make sure the check mark next to the analysis a separate file for each scanned page is UNCHECKED, and then press OK and proceed with the scan.

  Kind regards

  Shlomi