paths, do not type on!

Similar Questions

• Cannot access the network drive or impossible to mount the network drive. Error "network path was not found.

  Original title: network path was not found

  HI, after the upgradation from windows xp sp2 to sp3 (next to the customer) I can't access the network drive or impossible to mount the network drive. ' ' It showa error "network path was not found.

  Hi gauravadavadkar,

  Thanks for posting your query in Microsoft Communities. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the full error message?

  ·         Work on a domain?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with networkand check if the problem persists.

  S tep 2: if the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the steps to configure Windows to use a Normal startup state section of the article to start the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Startand then click run.

  (b) type msconfigand click OK.
  The System Configuration utility dialog box appears.

  (c) click on the general tab, click Normal Startup - load all device drivers and services, and then click OK.

  (d) when you are prompted, click restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  In Windows network connection issues

  You can read this article for more information:

  Windows wireless and wired network connection problems

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• Error 1314. The %appdata%\Autocad\ specified path is not unavailable

  Hi name is Kenya Caldwell and I am trying to install a program called Autocad, but whenever I do, I get the message following error 1314. The %appdata%\Autocad specified path is not unavailable.  I received a response from Autocad, but I do not understand, or not if it is correct.  Could someone help me with this problem?  Below is the message of Autocad.

  By specifying an installation location using a Windows environment variable

  Question

  When you have created a deployment or performing a stand-alone installation, you tried to specify the installation location using an environment variable, such as %ProgramFiles%, but you receive one of the following error messages:

  Please provide the path name where the customers go to install AutoCAD 2007 on their local computers.

  Error 1314. The path '% PROGRAMFILES%\..' is not available.

  Solution

  It is not possible to specify a variable of environment such as installation or the installation of customer location in a stand-alone installation or network deployment. If you install to different locations on different machines, it is strongly recommended that you use the deployment wizard to create several configurations of deployment for each location.

  To use a variable of environment as the installation location, you must run the installation of the product from the command line. This can be done by entering the following in the command line Windows or via a batch/script file.

  Note: This installation method is not tested or supported by Autodesk.

  Stand-alone installation

  MsiExec.exe /i "\Bin\AcadFEUI\acad.msi ' INSTALLDIR=%PROGRAMFILES%\

  Note: Replace the drive letter containing product for disk. Replace the rest of your installation for location. It is strongly recommended to use paths without spaces for this type of installation.

  Kenya Caldwell

  Salute to the Kenya,

  Try the steps mentioned by me in my first post and verify if the problem persists.
  See cannot install AutoCAD

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error when printing from a memory card: "year error occurred while reconnecting to \\epson 8af524\memory z card Microsoft windows network .the network path is not found connection .This has not been restored"

  Original title: there is an error occurred while reconnecting to \\epson 8af524\memory z card Microsoft windows network .the network path is not found .this connection has not been restored

  error message for a memory card has it printed

  Hello

  ·        Have you been able to print from memory card sooner?

  ·        How are you connected to the computer from which you are trying to print?

  This occurs when a computer uses the network map to connect to another computer to share files.

  To fix this problem, do one or more of the following methods.

   

  Method 1: Control equipment

  (a) ensure that the computer with file sharing turned on.

  (b) ensure that a hub network or router is powered.

  (c) ensure that the cables are well connected.

  If this does not resolve the problem, go to method 2: ensure that network resources are properly shared.

  Method 2: Ensure that network resources are properly shared

  Share a folder on a drive, then connect to the shared drive, follow these steps.

  Step 1:

  To make a folder that is located on the accessible hard drive on another computer, follow these steps.

  (a) right click onStart and then click Explorer .

  (b) right click on the folder you want to share, clickshare , and then click share this folder .

  Step 2:

  To connect to the shared folder from another computer, follow the steps below.

  (a) clickStart , then click run .

  (b) in theOpen box, type \\computer\share (where computer is the name of the computer where the resource network and share is the share name of the shared folder on that computer).

  (c) clickOK .

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When I try to open a game (Chess Titans, inkball, etc.), I get the following message: "c:\Program Files\Microsoft Games\Chess\Chess.exe the specified path does not exist.

  When I try to open a game (Chess Titans, inkball, etc.), I get the following message: "c:\Program Files\Microsoft Games\Chess\Chess.exe the specified path does not exist.  Check the path and then try again. "Should I do to get my games back so I can play them?  I've tried enabling/disabling of Windows features, but it did nothing.  I also tried to go through the run, but that has not worked.  And, I tried command prompt, but it says that I am not the administrator, who I am.

  Not accessible games

  I haven't had any changes consciously, and the games do not work in any user account.  When I've done sfc/scannow (command prompt) he said that I was not the administrator.  I could learn from another source to solve this problem - in the start menu, right click on the command prompt icon, and then click Run as administrator.  Hope everybody help with this problem.  If you do not have command prompt in your Start menu, any type of command prompt in your search box and it should appear.

  Anyway, my games work now.  Thank you

• Error code: 0 x 80070035 the network path was not found.

  Hi all

  I have 2 systems. In one system, I installed Windows XP Pro SP2 and in another machine I installed Windows Vista Home Basic Edition. The two systems are networked. I am able to access and view the shared folder in Vista the XP system. But when I am trying to access folders in XP since Vista I get the below error:
  Windows cannot access \\hyd02
  Check the spelling of the name. Otherwise, there could be a problem with your network. In an attempt to identify and solve network problems, click on diagnose.
  Error code: 0 x 80070035 the network path was not found.
  
  
  I did the settings below:
  (1) file and printer sharing are enabled in both systems.
  (2) firewall is disabled in the systems.
  (3) in the center of security and network, the network is private.
  and network discovery is enabled, file sharing is enabled, public folder sharing is turned on, printer sharing are enabled and protected by password sharing is
  Off, media sharing turned OFF.
  (4) the name of the task force in both the system is the same.
  Can someone help me solve this error...
  Thank you
  Sylvie G

  Hi Sylvie G

  Thanks for posting on Microsoft Answers.

  Are the same username and password on both systems?
  What is the share name you are trying to do on the XP machine?
  Let's say that the share name is music, you would get to it by typing \\hyd02\music

  Can you do a Test PING since the Vista PC on the XP PC?
  Go to a command prompt and type ping followed by the IP address of the computer XP

  Please post back the results... Thank you Ken
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 network drive mapping error: "error code: 0 x 80070035 the network path was not found."

  I recently started getting an error when you try to access my network drive. Attempt to fix I have also disconnected the drive and tried to reconnect. I get the error: error code: 0 x 80070035 the network path was not found

  I am able to map the drive of all the other machines in the hold of the House (Mac OS X, Windows XP, Windows Vista).  However, the Windows 7 machine continues to report the error.

  I searched the internet for the microsoft Web site and answers and so far nobody seems to have an answer to the problem (and it seems to be a very common problem in Windows 7, based on the number of reports I've met in my search). I'm able to reach the reader through the IP address, but cannot connect in it (continues to re - ask for credentials and I checked the credentials I use are 100% correct).

  The only significant event was the address IP changed on the remote disk. What that tells me, is that windows is not updated the name of the drive to the new IP address and confounds seriously on how to get the player passing the correct credentials.

  I removed the protection against viruses (a suggestion said it was the cause), but it has no effect. Check my sharing permissions and so many different places that I could, but nothing has changed and all seems OK.

  The problem is in Windows 7, but I don't know where all configurations "tricks" are on the (64 bit) OS - has been used for a 32-bit system. Where can I manually fix the DNS or DHCP parameter for the name of the drive?

  SOLUTION

  It's a problem with Windows Explorer in Windows 7 do not resolve the computer name target to its IP address. It is not a problem with the firewall or antivirus.

  There is a simple workaround solution.  Use the IP address of the target computer, not the computer name.

  (1) find IP address that the computer target is.  It is desirable to give a private static IP address to the target computer, for example, 192.168.1.10, so it does not change.  Use the local windows help when you sit in front of the target computer to do this, if you don't know how.

  (2) when you are sitting in front of the Windows 7 computer, you want to access the target computer, open Windows Explorer and in the address bar type------followed\\192.168.1.10 static address of the target computer, for example, and press enter

  If the target computer uses the name of user and password sharing, after a few seconds, you will be prompted credentials.  Enter the same username and password used to log on the target computer when you're sitting in front of it.

  The target computer will be added to the list of computer network Windows 7, appearing as an IP address instead of a computer name.  You can access his actions as if it was listed by name instead of the number.

  That's all.

• create new folder, but the path does not exist.  That's why I need to create!

  I want to take their existing case files, wallpapers and move them into a new catalog LR, jpg_edits.  In the import window, I left click on the parent, my photos and get 'create a new folder '. After which a new folder creation box opens to display the ms mode my file Explorer and the parent.  But he says to Select a folder, so when I try to type the new name, they tell me the path does not exist.  Which may be the reason I'm trying to create the new folder.  Everything seems to be able to do is to slect the existing folders.  Where is the creation of a new part of catalogue record?

  If I understand the question, you want to create a new destination folder in an existing parent folder. Fix? Once you click the folder parent in the Destination panel (left side of the screen to import), expect the top of the Destination table. You will find two elements here. The first, in the subfolder, allows you to enter the name of the new subfolder to create but it must ensure that the box is checked. Select the check box and enter the name of the file in the text field. Then, select the option in a single folder drop-down organizing. With these options, you will see a new subfolder in the tree under your (grey) selected parent folder. Even once all this is done on the right side of the screen to import.

• Site search path does not have to go to the results page

  BC instructions say to edit HTML code like below - to make a path to the results page.

  I see that?  This path does not to the results page, it goes to the default template page instead.

  < div class = "box" >

  <!-Search->

  < form name = "catsearchform50358" method = "post" action = "/ Default.aspx?" SiteSearchID = 2796& amp; / search_results.html' > '.

  < div class = "search-box" > < input class = "cat_textbox_small" type = "text" name = "CAT_Search" id = "CAT_Search" / > < input class = "cat_button" type = "submit" value = "search" / > < / div >

  < / make >

  < / div >

  <!-/ Search->

  Hello

  From what I see...

  ' / Default.aspx? "SiteSearchID = 2796 & / search_results.html" >

  Should look more like this...

  ' / Default.aspx? "SiteSearchID = 2796 &ID =search_results.html" >

  Reference: http://kb.worldsecuresystems.com/200/bc_2007.html#main_Redirecting_Site_search_results

  If still in trouble please provide the URL of the page so we can test further.

  Kind regards

  -Sidney

• The shortcut error message: the specified path is not; Maybe reinstall Firefox whenever I want to use.

  When I install Firefox, it works very well. Installation does not include a shortcut on my desktop, then when I try to start it again, I go to "all programs." Next, I get the message "the specified path does not exist. I think it has something to do with the confusion between two hard disks. C: drive, a small SSD, contains the operating system and other software. D: drive is my data disc, contains other applications, photos, music, etc. The way referred to in the error message is D:\Program Files (x 86) \Mozilla Firefox\firefox.exe.

  Firefox does not have the ability to choose a disk for installation. Is it possible that it is automatically installed on the C: drive, the shortcut continues to send on the D: drive?

  If you have any ideas or suggestions, I'd like to hear them.

  Using your file browser, look for Firefox in c:\Program Files (x 86)
  After, look in other files of the program (x 86)

  Once you find it, click with the right button on Firefox.exe and create a shortcut.
  Move it to your desktop. It work?

  Note: In the creation of shortcuts, you can without spaces. Instead of use;
  c:\Program Files (x 86), you should use; "c:\Program Files (x 86)".

• Firefox 4 for Mac after upgrade I can not type in the comments of several web sites area

  I've upgraded to Firefox 4 (beta very well executed) and now I can't type in the text boxes on a number of websites and surveys etc. For example on the Gigaom site I can not type comments (the name is fine, but the comments box does not work). But this is just one example. I ran across it on three other sites. Any ideas appreciated. (OSX 10.6.7, works fine on safari)

  I had a problem like this, and it is thanks to fonts that were corrupted in Snow Leopard 10.6.7. Apple has a fix on its support page.

  http://support.Apple.com/kb/DL1377

• Satellite A200 - 1 M 4 - can not type letter h

  PC laptop Toshiba Satellite A200 - 1 M 4

  When I type on my laptop all the letters are ok but the letter h does not appear. When I restart it it will be his forte, he won't until I press the FN key, then it stops.

  Also on my space password, there will be a lot of letter h, he won't stop not type self until I press the FN key again and then it will be ok except the letter h won't work at all, and also the FN functions will not work.

  I'll be very thnkfull if you solve my problem.

  I can't tell what's exactly wrong, but I can give you some suggestions
  I think there could be something wrong with the keyboard.

  Either there is a problem with the keyboard <->the motherboard connection or the malfunctioning of the keyboard.
  I would recommend checking the laptop in ASP.

  As you know the guarantee must cover all the problems of material, so it s worth it to contact the technician of the laptop.

  Good luck

• Tecra A9 - sometimes I can not type - click using the touch pad

  There are times that I can not type - click using the touch pad or other keys (all of a sudden without any reason)

  I can move the cursor in this case but not tap - click here to be able to click once again, I have to restart (this happens on both windows and linux)

  On windows, I press alt + ctrl + del and when the Task Manager window I can tap it and after I do I can tap - Select something else and so on.
  Click on the Task Manager click on anything else until I reboot and the problem goes away just to appear suddenly unexpectadly at the same time.

  I have the newest bios and driver accupoint

  Any tips?

  This happens only with touchpad, or when you use an external USB mouse?
  For me it looks more like the Windows operating system freezes for a short period. Is this good?

• Satellite L655-1john says error "the path network not found" when starting

  I just bought the laptop above and I did all the stuff he wanted to start and now when it is in the login screen and I go to my user and press ok while I connect it gives me the above message "the network path was not found"

  I have windows 7.
  Does anyone know what I'll do?

  I m confused now.
  After the first start, you must create new account and then you can start Windows 7 preinstalled and use the preinstalled operating system. I can't even imagine that this problem occurs the first commissioning. Recovery images are tested and you can install it 100 times and it should not happen.

  Have you done some changes or anything that might be responsible for this?
  Can get you into SafeMode (F8), create a new account and try to connect with this new account? The same thing happens again?

• upgrade to windows 10, cannot open itunes, it opened the first time, and imported all my songs, but does not open a second time, get the error that the path is not correct and file not found

  upgrade to windows 10, cannot open itunes, it opened the first time, and imported all my songs, but does not open a second time, get the error that the path is not correct and file not found

  Try to repair the security permissions for iTunes for Windows and the empty/corrupted after upgrade/crash iTunes library.

  TT2