Pavilion g6-1311eo does not start after overheating

Similar Questions

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• Pavilion dm4-1160us does not start after the failure of system recovery

  I have Windows 7 Home edition is installed. In my view, it is 64-bit.

  I get everything by initializing the error message is:

  "BOOTMGR is missing".

  Press Ctrl + Alt + Delete to restart»

  When running various tests (Tuneup, break-in, Start-up, hard drive) in I always get the same failure ID: M4PC2J-5KQ6N0-XD6V41-60VG03. The poduct ID is XH124UA #ABA.

  The case began after my computer froze and I forced the reboot.

  I guess that the hard drive is a gonner. Is this correct?

  Hi Mario,.

  Personally, I recommend to replace the hard drive yourself - it is a surprisingly simple process (and much cheaper).  A brief guide on this is detailed below.

  Your computer is listed as coming with a 500 GB hard drive, but you can also easily install a 750 GB HARD drive if you want a little more space - readers at the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  The procedure to replace the hard drive begins on Page 61 of your & Maintenance Guide.

  Once this is done, simply use your recovery media to reinstall the operating system on the new drive - this is described in the document of HP here.

  If you do not have your recovery media, let me know because there is another option, you can use it as long as you can clearly read the activation of 25-character product key on your label COST.

  Best regards

  DP - K

• Pavilion DM4-1265dx does not start after the restoration, the new hard drive

  Hello:

  I have a laptop of clients that a hard drive has been giving an iminent failure message.  I was able to create a disc of recovery and replaced the original HD (640 GB) with a 500 GB HD.  I can't do the factory recovery because the hard drive is smaller, but it allows me to perform a recovery of the operating system.  The question that I am running is after he read the DVD 6, the system wants to re-start and then it crashes just in the HP splash screen.  If I turn it works, I get could not find a boot device.

  How can I get around that, before the establishment with a win 7 CD?  Is this process of recovery to a waste of time, as I did on the previous model HP computers and it has always worked.

  Thanks in advance for any ideas.

  Mike

  Hi cloud:

  To be more precise, of memory, there are two options, reset and factory restore.  Factory restore won't do it because the disk is slightly smaller.  Factory reset will allow me to put the recovery disk hard, but when he re - start, it crashes just in the hp splash screen.  When I do the three fingers of salvation, then I get cannot find the boot device.  I made the internal test and everything passes with flying colors.

  I finished download an iso image and install from scratch, but I can tell you that it is the system more screwed up that I never ran into 30 years of working with these toys.  I tired to do a repair, but that creates just again the same symptom.

  I have an Acer Tablet that I've been able to use the computers acer recovery disk that was not intended (but had the same version of the operating system) and at least was able to get the operating system and software and finished to the top with the right drivers, size of the hard drive has been ignored in their case.

  Thanks for help you, it is appreciated, but I doubt I can recommend HP to one of my clients in the future based on what I've run here.  This is inconsistent with a solution of recovery as far as I'm concerned, that MS requires manufacturers.  Lets get real, hardware fails for various reasons, and you may not necessarily the same size hard drives with the rate of change occurring in the industry.  Personally, I prefer a game of installation for the operating system and drivers disks.  Dell is one of the only ones I know who did this, and as much as their material is so so, they do at least that right of the party.

  Once again thank you.

  Mike

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng

  

• Pavilion Media Center does not restart after the full system recovery. get the error code 0 x 4001100200001005

  Pavilion Media Center does not restart after the full system recovery. created recovery disks when purchased new. get the error code 0 x 4001100200001005

  Original title: recovery problem

  Hello

  According to the HP Support Forums, this error may be to do with the hard or for other reasons.

  You never have it replaced with a no HP bought in car?

  Read these threads HP on your error code:

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/recovery-disk-error-0x400110020000-1005/TD-p/22936

  http://h30434.www3.HP.com/T5/desktop-recovery-reply-only/trying-to-recover-an-old-PC-error-code/TD-p/964509

  If the original hard drive, press F11 at startup to start the process of recovery partition HP, did you recovery disks of.

  See you soon...

• Does not start after the upgrade to 1.5.

  Does not start after the upgrade to 1.5.  "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »

  All ideas

  No problems in the past with edge since September 2012.

  =============

  Laptop HP Pavilion dv7-2185dx

  Dv7-2185dx product name

  #ABA product number NV023UA

  Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology

  The microprocessor Cache L2 6 MB Cache memory

  6144 MB of memory

  Memory Max 8192MB

  Graphic ATI Mobility Radeon HD 4650 (M96)

  Video memory up to 2815 MB (1024 MB dedicated)

  500 GB (5400 RPM) hard drive

  Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer

  17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)

  Fax/Modem high speed 56 k modem

  Network integrated 10/100/1000 Gigabit Ethernet LAN adapter

  Wireless Connectivity Intel WiFi Link 5100AGN

  The Altec Lansing SRS Premium Sound technology with subwoofer

  101 keyboard compatible with the keyboard keys full size numeric keypad with integrated

  Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad

  PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)

  External ports

  5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card

  4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA

  2 headphone

  1 microphone input

  HDMI

  1 VGA (15-pin)

  eSATA + USB 2.0

  1 RJ-11 (modem)

  1 RJ - 45 (LAN)

  expansion port for computer 1 cell 3

  1 IEEE 1394

  irewire (4 pin)

  1 consumer IR (remote receiver)

  Other devices HP Webcam with integrated digital microphone

  Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)

  Weight lbs 7,74

  Housing for Kensington MicroSaver Security lock

  Turn on the password

  Accepts 3rd party locking safety devices

  Software

  Operating system:

  Genuine Windows Vista Home Premium 64-bit with Service Pack 1

  
  

  Hi, people.

  I was able to reproduce the problem here, so the good news is that you're not imagining things.  We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top.  This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform.  We will do the best we can and we will keep you guys, update as to what status is.

  Thank you

  -Elaine

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• The browser does not start after you have turned off and turned on the computer

  The browser does not start after you have turned off and turned on the computer. I tried to remove the program entirely (as well as personal preferences), to create a new account, install a different browser versions. All this has not helped. (I have Windows 7). Help, please! Every day I have to reinstall Firefox!

  Hello Nastena, try a clean reinstall, some Firefox issues can be resolved by performing a clean reinstall. This means that you Remove Firefox program files and then reinstall Firefox. Please follow these steps:

  Note: You can print these steps or consult them in another browser.

  1. Download the latest version of Firefox from http://www.mozilla.org office and save the installer to your computer.
  2. Once the download is complete, close all Firefox Windows (click on quit in the file menu or Firefox).
  3. Remove the Firefox installation folder, which is located in one of these locations, by default:
     • Windows:
       • C:\Program Files\Mozilla Firefox
       • C:\Program Files (x 86) \Mozilla Firefox
     • Mac: Delete Firefox in the Applications folder.
     • Linux: If you have installed Firefox with the distribution-based package manager, you must use the same way to uninstall: see Install Firefox on Linux. If you have downloaded and installed the binary package from the Firefox download page, simply remove the folder firefox in your home directory.
  4. Now, go ahead and reinstall Firefox:
     1. Double-click on the downloaded Setup file and go through the steps in the installation wizard.
     2. Once the wizard is completed, click to open Firefox directly after clicking the Finish button.

  Please report back to see if this helped you!

  • Also check if your antivirus or other access security software (firewall, antispyware etc.) blocks firefox.

  Thank you

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.