Pavillion 15n-236tu: SMART Check FAILED-hp Pavilion Notebook

I have a pavillion model 236tu-15n

Hello

ID information of failure "GOUSA73-0007N9-MFPV6J-60FJ03" which indicates that the hard drive has failed and that needs to be replaced to solve the problem

This problem could be due to an Application or a driver conflict, virus issues, corruptions of files due to incompatible applications, incorrect judgments, update failures due to conflicts, mounted sudden power so portable, sudden falls etc...

HP will offer a replacement HDD if the laptop warranty is Active, otherwise you can buy a SATA hard drive in a nearby retail store

Please make sure that you get at least equal as long as the original one in order to use recovery disks. If you need you can buy a bigger, but not smaller hard drive capacity. For example, if you have a 500 GB hard drive you can improve it to 750 GB hard drive, but not 320 GB hard drive

Please try the troubleshooting below indicated once the steps:

Step 01. Remove the battery and unplug the power adapter AC.

Step 02. Press and hold the power button for more than 30 seconds

Step 03. Plug the AC power adapter / (leave the battery for now)

Step 04. Press the power button and check if the unit is operating normally

If the steps listed above is not enough, then you can try reinstalling the hard disk on your laptop

If the problem persists again please Contact HP if your HP laptop is under warranty, HP could replace the hard drive and provide recovery media to restore the operating system to factory after the replacement (if you have not yet created recovery disks/USB support)

Note: Back up any personal data on an external drive if possible. Otherwise, you can connect the HDD defective via SATA USB adapter with another PC or a PC even after replacing the HARD drive & put in place of the operating system and try to copy / retrieve files. You can also check out the link below for additional help

http://www.WikiHow.com/recover-data-from-the-hard-drive-of-a-dead-laptop

Please click on the link in order to identify, prevent, diagnose & recover against any failure to drive on HP Portable Hard Drives & Solid State Drives:

http://h10032.www1.HP.com/CTG/manual/c02876562.PDF

You can check your warranty here to check the status and click here to order a new hard drive

Tags: Notebooks

Similar Questions

  • HP NOTEBOOK: Test System quick: drive hard SMART check failed

    What should I do when my quick test of the portable system says my SMART drive check failed?

    Failure ID: 9LPBSK-7SC875-XD7WLK-608Y03
    PRODUCT ID: T0X74PA #UUF

    Replace the hard drive is all what you can do. This is a fairly new laptop, it is still under warranty?

  • Pavilion g6: disk hard smart check fail

    Hi, I think I have problem with my hard drive. its not my hard drive got something like the use of 100% hard drive many years ago. I don't know why it happened but I solved this problem for 2 months, but now, over and over again worst - can't happen to bone. I tried HP PC Hardware diagnostics UEFI. I tried lying on my HDD and there was failure. Failure ID RLP960-6KR7JU-MFPWW1-60ET03. I don't know what to do, really need help. Thanks for the reply

    Hi Savagerys,

    Your PC's hard drive has failed, you need to replace.

    Here is a nice video how do

    https://www.YouTube.com/watch?v=ot8e0LKXZMo

    Once changed, you need to reinstal operating sistem recovery CDs.

    Hapends, don't worry, after modification, it will be perfect.

    All the best!

    Dindin

    <>

    * Click on the star of CONGRATULATIONS on the left say "thank you."

    Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  • Drive hard short DST check failed, HP Pavilion 15-e072sa

    Hello

    I left my laptop (HP Pavilion 15-e072sa / ID E4Q88EA #ABU) inactive for a few hours and when I came back to it, I realized it had frozen (a very unusual behavior for my laptop). I then tried to restart manually by using the switch button, however it are just. The display shows the HP logo and screen loading 8 windows "turning points" or, Alternatively, "prepare the automatic repair" sign for about 2 minutes, then writing disappears, but nothing else happens. I followed the steps recommended in the troubleshooting HP and ran a quick test activated by pressing F2 at startup of the system. The results are as follows:

    SMART HDD control: past

    verification of DST short of hard disk: failure

    Failure ID: RQF95H-6Q676H-MFPWXG - 60T 203

    I have no idea what that means the code above, but I would like to know if it is fixable without losing the data stored on my laptop. I have a few professional important files there, that I really need to retrieve. Your suggestions will be highly appreciated.

    Kind regards

    Mingus

    This is NOT official HP customer service and I, like most other people on this forum do not work for HP. It is a forum for users of peer-to-peer supported for class for the HP consumer products. HP maintains no official presence on this forum and it is unlikely that HP will respond in an official capacity. Response of an employee of HP represents his own opinion and not that of HP.

    Sorry, that I copied a previous post, I had made and impossible to remove the party requesting the HP part model / number and also the standard error. Once again, the same information and resolution apply to your situation.

    A failure of the DST indicates usually that the hard drive has failed or is about to fail and will have to replaced. After replacing the hard drive, please use the support of HP recovery, you created earlier to return the computer to a factory State.

    If you create your HP recovery media when you first set up your computer, please contact the official support of HP in your region / country, via the HP portal to support all over the world, to see if the HP recovery support is available for your computer.

    With respect to the data on the disk failed, remove the disc and put it in the USB 2.5 enclosure "SATA and connect it to a working computer. If the drive is still accessible, you can copy your work to another computer.

    If you have any other questions, feel free to ask.

    Please click the 'Thumbs Up' white LAURELS to show your appreciation

  • Drive hard Smart check FAILED 1. It does not boot to windows. Do I need another HD?

    Hello

    (Sorry for my English Italian..) I started windows, but strangely it went very slow, he continued to work, but very very slowly (no internet, it seems that I had 30 MB of RAM!) So I started "HDD regenerator" and he found bad sectors.

    When I finally interrupts him (too much time, 4% in 24 hours) the laptop (HP PAVILION 15 n006sl) can't find windows, it asks for me to start a startup (like a USB stick or a cd) disk.

    INTELLIGENT CONTROL: FAILURE

    FAILURE ID: GQF1VK-709794-MFPWXF-60BE03

    HARD DRIVE 1

    ---------------------------

    For more information, please visit: www.hp.com/go/techcenter/PCDiags

    What should I do?

    There is nothing I can do without having to buy a new HD?

    Thank you

    Ernesto

    Hello

    Error code 24 characters for the SmartTest failure would indicate that hard is defective and must be replaced.

    If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

    If you live in the United States, contact HP here.

    If you are in another part of the world, begin here.

    If you are out of warranty and would like a guide to replacing the hard drive yourself, please let me know - includes the complete model number and Nr laptop - see here for an explanation.

    Kind regards

    DP - K

  • Laptop HP 650: smart check:failed.failure id = PLMBK-00087F-MFKSWJ-60E603

    error ID = PLMBK-00087F-MFKSWJ-60E603

    Hello

    It is necessary to replace the hard drive with a new one (SATA 2.5 "), check the page 46 to 48

    http://h20628.www2.HP.com/km-ext/kmcsdirect/emr_na-c03310281-1.PDF

    750 GB, 5400 RPM, 9.5 mm 634250-001

    640 GB, 5400 RPM, 9.5 mm 669300-001

    500 GB, 5400 RPM, 9.5 mm 669299-001

    320 GB, 5400 RPM, 9.5 mm 622643-001

  • BioHD-8 error code a smart test failed on the drive

    I am running vista Home premium that came pre-installed (so I don't have a disc) on a hp pavilion slimline S3500f

    I had a problem when windows wouldn't load, just kept freezing and restarting a couple of times before it load.

    I was recommended to change my graphics card, which I did and windows starts to load and then arrested again.

    Then I got a blue screen Uni, when I ran a diagnostic test, I got an error code BioHD-8 a smart test failed on the drive

    I have Norton anti-virus installed on the pc

    I would really appreciate your help on this, thanks in advance

    Hello
    I would suggest to run Startup Repair and check if it helps:
    http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

    Otherwise, I suggest you post the question in the hp forum and check if that helps:
    http://h30434.www3.HP.com/T5/desktop-hardware/BD-p/HardwareDPC

    It will be useful.

  • Smart check for hard disk

    My computer is a Pavilion dv7 - 6123cl.  My operating system is windows 7.  I get an error message indicating intelligently check that my hard drive is about to fail.  When I use the tests diagnostic to check HP short and long check, it says that my drive is check.  It seems to be something in Windows 7 that is running the Smart check that produces the error message.  When I try to use the windows diagnostics program, it says failed.  When I try to any control using windows check, it says failed.

    Heck, Toshiba is one of the few that does not offer its own hard drive diagnostic tool.

    You can download, run CrystalDiskInfo, see what is the smart data shows, this is a portable version that does not install anything on your PC, just past in the folder you unzip it to.

    http://sourceforge.jp/projects/CrystalDiskInfo/downloads/56196/CrystalDiskInfo5_0_2.zip/

  • HDD SMART Check: FAILURE

    I have a HP Envy 15 JL - 073 cL (Win8.1) and I had not used for a few days, and when I turn it on it says hard drive failure and I should back up. Here's what he said:

    "Processor Check: PAST.
    HDD SMART Check: FAILURE

    FAILURE ID: GK5L3D-74E767-RXGJWK-609903
    PRODUCT ID: E0M39UAR #ABA

    Hard drive 1

    ————————————————————

    "The comprehensive system test: FAILED.

    I have already restored it once due to an error, why twice? Is there another way?

    Hello

    Error code 24 characters of the disk failure short Self Test would indicate that hard is defective and must be replaced.

    If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

    If you live in the United States, contact HP here.

    If you are in another part of the world, begin here.

    If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

    Kind regards

    DP - K

  • Satellite C660 - update BIOS stops on: project ID check failed

    Update 1.4 stops on: project ID check failed. I have the Satellite C660, BIOS 1.0 version.

    Thahx for help.

    Can you post more information please?

    What model of laptop you have exactly (C6660-xxx)?
    Are you using the original operating system preinstalled that you got with your laptop?

  • check failed. There was an error connecting to server Apple ID.

    check failed. There was an error connecting to server Apple ID.

    What do you do when you receive this alert?

  • Mini 110-1125NR: password for the mini 110-1125nr GB check failed

    Password check failed
    Fatal error... system halted.
    CNU946BSVX

    @Tr_wm09

    Enter: e9lovgpn64 (in both cases, the 4 rd character is a lowercase L)

    or
    e9lovgpn6r

    Kind regards

    DP - K

  • HAB check failed for start / could not validate the boot image

    Hello

    I have neglected my E bike for a few weeks and when I loaded and it fed today, it shows a menu and:

    HAB check failed to start

    could not validate the boot image

    Tried all the menu items and none of them worked. For me, it's very odd behavior, because BONE is not affected since the last Android 5 update, several months ago.

    Are there opportunities for the device?

    If you can't make an external reset via hardware buttons, then your phone will have to service.

  • HP Mini 110: The password check failed. FATAL ERRORRRRRRRR

    Hello I have the same problem with my computer hp mini 110. I've not used in about a year because I lost the charger, after stumbling on my mini in my car again, I decided to buy a charger for that as I give it to my MOM to use, so that she can get better computers and technology duration.  Now when it turns on it will ask for a current password.

    It says the password check failed

    Fatal error... System stopped

    CNU9363C22

    Can anyone of you guys please help me?

  • [Spectrum XT] Encountered issue SMART Check

    I just got this new ultrabook, for two weeks in and just yesterday, I started getting lockups and BSODS.

    I checked the observer of events 7 and began to notice the newspapers mentioning:

    The device, \Device\Ide\iaStor0, did not in the expiration time.

    Fine, then I googled and found that it is related to intel rapid storage manager. I downloaded the utility of the website of intel (HPSF.exe stopped working, reinstalled and it has not found the related updates for my intel rapid Storage Manager).

    Now after the update, the error log is gone, and he has been replaced by something more sinister:

    The device, \Device\Harddisk0\DR0, has a bad block.

     

    This article has appeared many times in the event window and fills constantly that I operate my ultrabook. Well, I reinstalled HP Support Assistant from the Web site and when I run the diagnostic tool, he told me that I had a SMART check the issue, and the player will die soon.

    SIGH. It's been only two weeks and I came across THIS? I didn't sign up for this when I paid a thousand dollars for a superior product!

    To add salt to the wound my recovery USB media I created did not work and I am doing a service center work recovery media.

    I've already opened a ticket with chat online support and advice needed to run the diagnostic level BIOS, same result. Micron SSD is going to die soon.

    What could have caused this? I selectively chose a ultrabook with SSD for its robustness, but it ends up being the first media who died on me! I'm certainly NOT happy about it.

    I ran a number of other tests of another utility, namely one of them HDDtune and it signals more than 5000 bad sectors. I clicked on stop before he finished. I've seen enough of trying to know the reality of the situation.

    The thing starts always quick and the BSOD stopped, but I get freezes from time to time, it started past yesterday.  Everything worked perfectly since I bought it so far! (with the exception of the creation of media USB bad recovery)

    FYI, the ultrabook is running more hot that I'm comfortable with (sometimes), especially near the speaker grille. Is this normal? It is quite localized in the grid only.

    The problem you are having is very rare. Disc SSD is very sturdy, but like any other electronic component, can go wrong. You have the SSD enlarge as the only storage, or drive combo of the WSSD Accelerator, then on a mechanical hard drive? In the first case, it wouldn't be difficult to detach the acclerator reader in the console of the IRS then replace with a new one and then reconnect this one. If you have an SSD enlarge it will mean replacement.

Maybe you are looking for