PCI-MIO-16-4 error 200329 after running a while

Similar Questions

• 200170 with PCI-MIO-16XE-10 error

  Hello

  I work in a lab and one of our machines had to be updated in Labview 8.5 in 2011 to implement a new box to tools.  I changed any code and have not yet implemented any changes for the new box to tools.  In addition, the program worked before the upgrade. Now, when I run the program I can not run a test because some parameters that indicate that everything is ready are not fulfilled, these parameters are read by the PCI-MIO-16XE-10 (Dev3).  Then, when I stop the program I get the following error:

  

  I use the DAQ assistant to read a Digital-In.

  After you have upgraded, I assume this problem is either bettween compatibility 2011 (probably DAQmx) and the card PCI, or that the driver for the PCI card does not work right (even if it says that the device works properly on the 'Self Test' max).

  While the above issues likely causing the problem?  The PCI-MIO-16XE is only compatible with traditional and not DAQmx?  How can I check to see if it is set up right if it is compatible with DAQmx?

  Thank you

  Link

  The problem is exactly what this message says. The device has only port0. He could never have worked with port1.

• Windows 7 troubleshooting error 0x8E5E0247 after running sfc/scannow

  I'm having this problem of solving the problems of network connection. I ran sfc/scannow, and the results are that Windows Resource Protection finds corrupted files but was unable to fix. What should I do now?

  Hello

  Don't forget to run checkdisk so

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  =====================================================

  The errors may not have something to do with the problem you are experiencing:

  Check the Option 2 here:

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Many files that SFC cannot resolve are not important.

  Start - type in the search box-> find CMD in top - click right on - RUN AS ADMIN

  put the command from below (copy and paste) in this box and her and then press ENTER.

  findstr/c: "[SR]" %windir%\logs\cbs\cbs.log > sfcdetails.txt

  who creates the sfcdetails.txt file in the folder that you are in when you run it.

  So if you're in C:\Windows\System32 > then you will need to look in that folder for the file.

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228 and http://support.microsoft.com/kb/929833

  This creates sfcdetails.txt in C:\Windows\System32 find and you can post the errors in a message
  here. NOTE: there are probably duplicates so please only post once each section error.

  You can read that the journal/txt files easier if you right click on Notepad or Wordpad and then RUN AS ADMIN-
  then you can navigate to sfcdetails.txt (in C:\Windows\System32) or cbs.log (in C:\Windows\Logs)
  According to the needs. (You may need to search sfcdetails.txt if it is not created in the default folders.)

  I hope this helps.

• BIOME-1 error when you run the diagnostic material for RAM test

  In recent months I've known several blue screen errors during startup. Initailly, initially, I thought that maybe it's a hardware error, but after running Diagnostics of material (press F9 to start) and have all the tests passed so I assumed it was a software problem, I focused my attention on that. However, today, I started to run hardware diagnostics and I discovered that I had a RAM issue with the BIOME-1 error code. Is it possible that the hardware diagnostics can not full capture errors and that a RAM issue was first the cause of blue screen errors?

  I called HP support and they sent an engineer to the bottom. After you open the computer case, the cause of the problem has been established as a RAM module that was not properly secured. After getting the RAM module, the blue screen errors did not reappear again. The engineer also ran some tests and confirmed that everything was fine.

• Can't run a PCI-MIO-16-1 (6070E) more quickly than half speed

  I'm new to all this, so please be understanding. I have a PCI-MIO-16-1 running CentOS 5 with NIDAQBase 3.3.0 and NATION 1.1.0. This card should be able to do 1.25Ms / s I need 2 channels running at half that speed, which is perfect. I was nothing to do, but play with the contAcquireNChan.c sample that comes with the battery. My first problem is that I discovered that I could not run the map faster than 20Ks/sec. After you play with it for a few days, I upgraded my software stack of 3.2.0 and, and I suddenly could spear the map faster! I had not changed my code. I was getting 1-channel 625Ks/s really well. Then I changed my code to capture two channels, and I found nothing that I can receive the card run faster than half the speed. And I mean just, say, 650Ks/s. I can run a channel to 625, or 2 to 310, and I suppose that 4 to 155, etc.

  If I'm right on the edge, my program will crash after a few seconds with the following error:

  DAQmxBase error: RLP invoke node it is not enough data in the DMA buffer to complete reading of the VI buffer.  Request less data, or wait until there is more data in the DMA buffer.

  If I'm 'more' the little 'edge' sampling rate, the program will crash immediately with:

  DAQmxBase error: DAQmx Base Read.vi
  Some or all of the requested samples are not yet acquired.

  So my questions are: I'm just misunderstanding how this card? 625Ks/s is necessary limit it? Or am I not call functions properly to get the full flow? Or, perhaps, given my experience with the upgrade to 3.3, is there still something wrong with the drivers? Should I look for a newer version of the software? Can I get a preliminary copy of the next beta to try? Finally, should I go by using correct DAQmx (not the "base"), even if it has not been updated since 2005 (I need to downgrade my OS)?

  I'll fix my example (modified). It really is, I'm doing here of things really simple. Maybe someone with more experience can spot an obvious error.

  Thank you very much!

  DK

  Hi David,

  I'm in Group DAQmx Base, and the AI limit you encounter is a defect in the DMA code. Because you use a PCI on Linux, the best route for you to take use DAQmx 8.0.1 [1]. It is true that the driver is old, but your material is plu ;-)

  Although we have not done internal testing to know for sure, CentOS 5 will most likely run DAQmx 8.0.1. Since you already have OR-KAL 1.10 configured and running, DAQmx 8.0.1 should install quite easily. From there, you will have a better pilot as well as more hardware features supported.

  However, if the kernel uses CentOS 4 k stack (as new versions of RedHat), you may experience a kernel panic. If you are in this situation, let me know and you and I can't for alternatives.

  [1] DAQmx 8.0.1 for Linux
  http://Joule.NI.com/nidu/CDs/view/p/ID/1194/lang/en

• Errors in the event log after running hp support assistant

  Model: M6-1045-dx

  Product number: B5S08UA #ABA

  OS: Windows 7

  I recently discovered and ran hp support assistant.  I have installed all the updates proposed, which were:

  Update BIOS to F25AP1

  HP simple pass upgrade to 6.0.100.257

  HP 3.00AP4 Security Assistant

  After doing so I see WMI event 10 errors

  «Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.»» Events cannot be delivered through this filter until the problem is corrected. »

  and the mistakes ISCT agent 1003 error code

   

  
  They appear on the reboot of the system.  See in the event viewer on the windows applications.  a little confused these has started after running updates of HP.  Could someone enlighten me as to what tell me these errors and if I need to worry.  Thank you!

  If any other care, upgrade to the latest version of the driver isct removes most of the errors to product isct.  Remains more than a warning, "ISCT - CAgentService::AgentServiceInit BIOS iSCT 3.0 implementation has not been detected - fallback to take in charge the 2.x feature", which seems innocuous.

• Desperate: What is the speed of a simultaneous acquisition of data NO? (PCI-MIO-16-1 (6070E))

  I am struggling to understand how fast, I should be able to run my PCI-MIO-16-1 (6070E). The card is valued at 1.25MS / s. I understood that run several channels divided it. I'm perfectly fine with that. Specifically, I need 2 channels clocked at 625KHz, each, this card should be perfect. However, in practice (using MAX or SignalExpress), can't the card to run faster than about half that speed. In other words, I can take 2 channels at 315KHz. If I go on that, I get a 'strange' behavior, including a machine so overloaded and lazy that I have a hard time to kill the process. If I go directly to the maximum speed, I just get an error about the ADC does not complete on time.

  I've been more present here: http://forums.ni.com/ni/board/message?board.id=250&thread.id=52447, but I had marked this thread as resolved. Indeed, this Council has me full speed running on a single channel, and it's a thing of beauty. However, I hit a different limit, so I'm trying a new thread.

  This seems to be a very simple question: what should be the theoretical maximum speed be on this map, once I have start trying to take more than one channel? Am I restricted to less than a total of 1.25MS / s due to the action of switching of the CDA that she questions the channels? I can't get 1.25MS / s single channel? I'd be able to do 2 625KS/s channels, or that I'm wasting time because the card does not have a simultaneous sampling? If I can't spin the full flow I think I should get, I must have a different card and move. I don't know if I'm wrong, or hit a hardware limitation that I don't know.

  Thanks for reading!

  DK

  
  

• Realtek RTL8101 PCI Ethernet is in error during startup

  Hi all
  I have EDT recently bought by Satellite A200-1CN notebook PC series. I'm having a problem at the start of the system that has Windows Vista installed.
  The Realtek RTL8101 PCI Ethernet v 1.02 (060510) gives error during startup. The error is to run is as follows

  PXE - E61 Media Test failed
  MOF: Left PXE ROM

  Can any help with this problem

  Concerning

  Hello

  Hmm you ve you have a problem with the Vista boot! :|

  Usually, this message appears because the BIOS can not find a source of start-up as ODD or HARD drive and then try to boot from LAN.

  Perhaps the BIOS can not find HARD drive due to a hardware problem.

  Hmmm. First of all, you should try to change the boot order in the BIOS. Put the HARD drive as first boot device.
  Save the settings and try to restart the laptop. If it is not possible to start the Windows Vista I guess that HARD drive is dead!

  Have you tried to reinstall Windows Vista using the Toshiba Recovery CD? Check this box!

  If all this procedures don't help I recommend you contact the ASP in your country.
  The technician must check the laptop and if necessary, it should replace the HARD drive.
  Your warranty is valid so that everything should be done for free.

  Good luck

• Meter very low frequency using PCI-MIO-16-4

  Hello

  I am trying to use a card PCI-MIO-16-4 with BNC-2090 to CI FREQ. Because the sometimes less than 1 Hz frequency of our leaders, or even no time measurement taken, the vi program always shows "Error-200527" and tells me that the min frequency must be greater than 1,192 Hz. If this card cannot measure very low (even zero) frequency in time measurement taken? If it is possible, how? Could you show me some examples? Thank you very much.

  Damien

  What method of measure do you use to measure your rate?  You are able to assign at least 0 (default) to 2 that would be the rounded version of 1,192.  Alternatively, you can try to use one of the other methods to measure and see if that helps.  All these values can be set with the channel to create VI.

• My slowsdown LV after running for several hours program

  Hello

  Could you please help me in my problem explained below.

  My experiences require to run the program from LV for 2-3 days in a stretch of collecting data to 10 Hz speed using a release configuration. But after running for a few hours, the program slows down, not buying the data with the same speed. If I restart the program again, it works very well with the required speed.

  I have LV v4.0.1 running in my Windows 2000 operating system. I have the card PCI-GPIB connected to Lecroy 8901 GPIB interface for data acquisition. I also LAB - PC + to control some engines.

  I have NEITHER-DAQ 6.6, NI-VISA for windows 95 / NT installed in my system.

  I thought that the problem could be my low end computer and recently updated with motherboard relatavely high speed and RAM. But the problem is still there.

  I have attached my program with this message file.

  valueble suggestions are greatly apprecited.

  Thank you.

  You generate data for display and it makes your system slow.

  Keep your smaller screen and write data on the disk.

• I received this error message after you remove the address something about Cloud.app

  I received this error message after you remove the address something Cloud.app.   Can you tell me how to fix this error message. "  '/'  "  ?

  Hello Phyllis,

  When you receive this error now?

  Let's run boot minimum troubleshooting to find the cause.

  Windows XP:

  http://support.Microsoft.com/kb/310353

  http://support.Microsoft.com/kb/316434

  Windows Vista and Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Please note that after refine us the cause, it is important that we return to a normal startup and manually delete the startup program.

  Best regards

  Matthew_Ha

• error 1 when running standalone executable

  Hey everybody,

  I'm having some trouble with an app that I'm building in an executable file. Now, it seems that everything is build without errors, but when I go to run the executable file I get a weird 1 error from one of LabVIEW built in libraries. I tried to do remote debugging, but I do not see the error pop up in my code anywhere, so I'm a bit confused as to what is happening.

  The error does not collect until after I click on a button that loads a VI in a secondary school (high school even load the correct VI). Also, I don't get any errors when I run the VI in the development environment.

  I have attached a picture of what the error said.

  Thanks in advance for the help.

  Ryan

  Your error message indicates that the error is from the VI who writes in a configuration file and has nothing to do with the sub-panels or the reset of values. You're probably update a configuration file with certain values or something. You show your real code makes it, but if I had hazad a guess I would ask are you aware of this: why my executable not working when using the VI Constant current path?

  As for your question on the application path: http://zone.ni.com/reference/en-XX/help/371361H-01/lvprop/app_appdir_path/

• DAQMx NI PCI-MIO-16-1 for BPSK/QPSK Laser Comms test

  Hello

  I am completely new to LabView and trying to write a program that will create a BPSK/QPSK or QAM signal for me to create my Department (NI PCI-MIO-16-1) using DAQMx Board. I do not have the toolkit modulation and thus need to make from scratch (I guess).

  My main question is whether it would be possible for me to create my signal desired in MATLAB - because I am really uncomfortable with this programming language - and move my LabView signal for her to be expelled as a sign of real tension using the DAQ boar.

  Whatever it is, what would be the best way for me to create these signals if I do not have the Modulation Toolkit, I see the entire Web site of NOR?

  As things are, I already managed out of some built-in waveforms (sine, triangle, etc.) using features available in LabView. However, if I try to do a sinusoidal signal using MATLAB code

  (for example, x = 0: pi / 24:2 * pi;)    y = Sin (x); ) where I take only out of my box of The Mathworks and plug it into the block to "Build the waveform" whose production goes to the DAQ assistant, I get errors on my don't not execution of MATLAB code.

  Ultimately, what I want to do, is create the signal to drive a PCB I to modulate a laser diode and then capture it again at the exit of a photodiode.

  Thanks for your help!

  Spyros

  Hello Imtiaz,

  Fortunately, I managed to resolve it in the last days. Thanks for your help!

  Spyros

• Error message after extraction of sp3 for XP Pro: System cannot find the path specified.

  XP Professional installation error message after extraction of sp3 on hard disk, message: System cannot find the path specified.
  Whenever I try to install, I get the same message. How can I fix it? I can't use the "fix" without sp3 installed.
  Any help would be greatly appreciated!

  "system cannot find the path specified".

  A google search revealed this can help...
  http://aumha.NET/viewtopic.php?f=62&t=33406

  Also, what is your level of service current pack (start-run then type Winver, and then press enter)? If you have no current service pack level, you must first install SP2. Unfortunately, the link for that

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=28

  doesn't seem to work today. If all goes well he'll be reinstated soon.

  Tricky

• I am not able to connect on all sites with my system XP displays a 404 error code after a Trojan horse (trojan. ADH.2) was found and quarantined by norton.

  Hello, I'm not able to get online at all sites with my system XP displays a 404 error code after a Trojan horse (trojan. ADH.2) was found and quarantined by norton. The system is slow or bottleneck at all, but I think that the registry has taken hostage by this Trojan horse. I tried to run Add ons, reset IE8, reinstall IE8 offline, I tried different users, tried to run a different browser (firefox). I can ping all the sites in the cmd prompt, but have no luck connection in the browser. A ran mohamed, superspyware, spybot. Is that what I can do without having to re install? I don't have the OS XP Media.

  original title: error 404 on all sites

  I wouldn't worry IPSec.

  I think the most important things to address are:
  1 search for rootkits.
  2 empty the DNS.
  3 reset the proxy settings.
  4 reset the TCP/IP and Winsock settings.
  Good luck!