photoelements installation stuck at 87% returning back 13

Similar Questions

• Satellite C850-A958 - BT Stack installation stucks & utilities BT are not available

  Model: * Toshiba Satellite C850-A958 *.
  Purchase date: January 13, 2013
  Warranty status: still under warranty until January 13, 2014

  * Issue 1: * "Bluetooth Stack" utility is blocking and not to complete the installation procedure.

  * Problem 2: * there is no utility 'Bluetooth' work due to the installation of stuck.
  Operating system: Windows 7 64-bit

  Address the situation/address Description
  My laptop SSD (Solid State Disk) had a manufacturing defect represents in the form of bad sectors & because of the guarantee, he was in a process of change for the defective part by the center of service allowed in my country.

  When she came back to me, I started to install the operating system and drivers (my computer portable edition does not include operating system drivers).

  I faced a serious problem and it was not existing before, when installing "Toshiba Bluetooth Stack for Windows" the installation process is not completed successfully and it's freezes to an important point.

  This process blocked the program of "Bluetooth Stack" menu is already created and if I try to run any utility of it I get an error message saying: + "the program can't start because TosBtAPI.dll is missing on your computer. Try reinstalling the program to fix this problem. » +

  Installation stucked treat freezes - for more than two hours in fact - and the only solution cancels the right low "Setup Bluetooth Drive_r" installation process by pressing "Cancel".

  After windows restarts, I found the menu of the program seems like a properly installed (complete the menu & highlight of the elements on the inside), but if I run one of the utilities include a message required to reinstall the Bluetooth driver and when to start it stops at the same point of freezing again as endless and repeated behavior.

  I tried to install a new copy of Windows several times - also re - download the source file for the Web from Toshiba site several times with the same result every time.

  Currently, I can't use any uility driver bluetooth more!

  I want to know:

  What is the solution to this situation?
  Is it possible that the bluetooth hardware is damaged during the process of evolution of the SDA in the service center?

  Thank you

  Hello

  I think I know what you did wrong the laptop supports the Realtek Wlan / BT combo card.

  This means that a single module shares the feature WLan and BT.
  To ensure that the two would work correctly, a [Bluetooth Filter Driver Package | http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 2 & selSeries = 312 & selProduct = 7499 selSh 3439 = ortMod & language = 13 & selOS = 30 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 1 & ID = 81895 & OSI D = 30 & driverLanguage = 42] must be installed.
  After that, you could install the battery Toshiba BT.

  Next to the installation of this software, you must also install VAP (value added package) which is an essential part in the Windows 7 environment.

  Once again:
  First install: VAP
  Then Realtek Wlan driver, after this suite Bluetooth Filter Driver Package by Toshiba BT stack

• I chose to open files by default .exe for internet explore. Now I can't open microsoft word2007, Notepad, mozilla, chrome, etc etc as iexplorer opens when I click on any program. How to return back?

  I chose to open files by default .exe for internet explore. Now, I can't open chrome, mozilla, Notepad, microsoft, etc., etc. like iexplorer opens when I click on any program. How to return back?

  I tried this solution

  "When you run an .exe on a Windows XP, Windows Vista or Windows 7 computer file, the file can start another program."

  microsoft community.
  The problem I encounter is that I can't even open Notepad or command prompt window window download internet explore opens and I'm stuck there. Please help me get out of this quagmire.

  Hi Wiillam,

  This problem occurs because the icon cache is not updated correctly.

  Refer to:

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  (http://windows.microsoft.com/en-US/windows7/Back-up-the-registry ) How to back up and restore the registry in Windows.

  Icons change incorrectly in Windows

• E.M.P. Installation stuck at installing weblogic

  Hello

  We're reinstall on the computer after the complete uninstall.  By the way same OBIEE installation has also been glued on the same way on the same server.

  OBIEE 11.1.1.7.1 Installation stuck at 97%

  We have workaround for this problem on SR. He has been to install weblogic separately, then install OBIEE.

  Concerning

  G1

  11.1.2.4 product version

  Windows Server 2008 64 bit

  Screenshot

  

  Journal

  2015-12-23 22:32:04, 498 INFO [readSilentXML] com.bea.plateng.wizard.installer.common.parsers.TemplateParser - Silent xml file successfully treated...

  2015-12-23 22:32:06, 307 WARN [home] com.bea.cie.gpr.internal.model.JvmTargetManagerImpl - value of the property for win32_jdk160_29b11.zip not found...

  2015-12-23 22:32:06, 307 WARN [home] com.bea.cie.gpr.internal.model.JvmTargetManagerImpl - value of the windows_ia32_jrockit_160_29_D1.2.0 property - 10_jdk.zip not found...

  2015-12-23 22:32:06, 479 WARN [home] com.bea.cie.gpr.internal.model.JvmTargetManagerImpl - value of the property for win32_jdk160_29b11.zip not found...

  2015-12-23 22:32:06, 479 WARN [home] com.bea.cie.gpr.internal.model.JvmTargetManagerImpl - value of the windows_ia32_jrockit_160_29_D1.2.0 property - 10_jdk.zip not found...

  2015-12-23 22:32:06,495 [House] WARN com.bea.plateng.wizard.installer.silent.tasks.SilentBEAHomeTask - D:\Middleware\EPMSystem11R1\... Directory is not empty. Proceed with the installation?

  Hello

  Found this remark 2099095.1 published recently.

  Cause

  The installation process attempts to access the Oracle lb site - ccr.oracle.com.  The current security settings of firewall allow connection to the site, but they are blocking content being returned by Oracle.

  To verify that this is the issue, while the WebLogic installation is underway:

  1. open a command prompt window.
  2. type: netstat
  3 check the flow rate for a connection to lb - ccr.oracle.com, listed in STANDBY mode

  Solution

  In the configuration of your firewall, enable "Download content" for lb - ccr.oracle.com.  Or completely block the lb - ccr.oracle.com.

  Although I am confronted with exactly same error on newspapers, this side is not in standby mode. Always wanted to check how can I block this link?

  Concerning

  G1

• My T540p turns off an AC to work on drums and never returns back

  Since the last device of management power Lenovo update (somewhere 6-13 Oct 2015), my T540p jumps out of his power and never returns back, until I have turn it off and disconnect the battery.

  When I start Windows 10 after the battery is disconnected, it loads for a few minutes and then to the battery. Whatever I do after that - Plug and unplug the power adapter, change to another adapter (I have a spare), extinction, reboot, poweroff connect AC - nothing works. When I disconnect the battery and plug back - normal behavior is restored.

  I have dual boot on my T540p with linux (Gentoo, kernel 4.2.3). Linux works OK. The problem appears only when I boot Windows 10.

  It turned out that Windows has jumped to a special power - autonomous mode. Once I turn it back into balance, the battery took over. I couldn't understand what Windows switch to the mode of independent power supply.

  It's very sad that CE supports standalone through reboots and poweroffs. It is not logical to disable the battery charge when the machine is turned off completely.

• My computer keeps trying to install 14 updates, but when it gets to the point where the computer restarts returned back without installing them. Error 80070020

  windows update

  My computer keeps trying to install 14 updates, but when it gets to the point where the computer restarts returned back without installing them. Get an Error 80070020, I am unable to find out exactly what to do. Every day for a few weeks he tries to install the updates and then stops to install but always ends up coming back. Can you help me please?

  Hello

  read thisL

  Windows Update Error 80070020

  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-Error-80070020

  and also see if this helps to fix:

  How to reset the Windows Update components?

  There is also an automatic 'fix - it' here

  http://support.Microsoft.com/kb/971058

  Also, try to put the KB numbers in the search on the link below and then manually download the

  http://www.Microsoft.com/downloads/en/default.aspx

  or please repost your question in the correct windows update forum

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

• service pack 2 installs but returns back tried nseven times

  I installed the service pack 7 times and he said: he has successfully installed you attempt a restart and he says he has not installed and comes back in return what I am doing, I am told by telus ineed service pack 2

  Hello

  This article explains how to troubleshoot problems when you install a service pack for Windows Vista or Windows Server 2008.

  http://support.Microsoft.com/kb/947366

  Use this forum link for all questions related to Windows Vista SP1, Windows Vista SP2 and Windows Server 2008 SP2 below.

  http://social.technet.Microsoft.com/forums/en/itprovistasp/threads

  or repost in the Windows Update forum link below

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

• Captain El installation stuck

  installed at El Captain on my iMac. After reboot, I have a white screen. I read online to restart. This did not help. Help!

  Please take each of these steps that you have not already tried it. Some of them are not applicable to your model or your situation. Stop when the problem is resolved.

  To restart a computer is not responding, press and hold the power button for a few seconds until the unit turns off, then release, wait a few seconds and press again briefly.

  Step 1

  The first step to respond to a startup failure is to secure data. If you want to keep the contents of the boot drive and you have not already at least a current backup, you should try to back up now, before we do anything else. It may or may not be possible. If you don't care the data changed since the last backup, you can skip this step.

  There are several ways to back up a Mac that is unable to boot. You need an external hard drive to store backup data.

  a. starting the partition recovery or an hour Local Machine backup volume (button option key at startup). When the OS X Utilities appears, launch disk utility and follow the instructions in this support articleto the title of the "Instructions for the backup on an external hard drive via disk utility". The article refers to the start of a DVD, but the recovery mode procedure is the same. You don't need a DVD if you use OS X 10.7 or higher.

  (b) If step 1 fails due to disk errors, and no other Mac is available, then you may be able to save some of your files by copying them in the Finder. If you already have an external hard drive with OS X installed, the start of it. Otherwise, if you have access to the Internet, follow the instructions on this page to prepare the external hard drive and install OS X on it. You will use the installation program of recovery, rather than download it from the App Store.

  c. If you have access to a Mac, and it work and have both the non-working Mac FireWire ports or stroke, start the Mac non-working in target disk mode. Work Mac to copy the data to another drive. This technique will not work with USB, Ethernet, Wi - Fi or Bluetooth.

  d. If the internal drive of the non-working Mac is replaceable by the user, remove it and climb into a docking station that is pregnant or an external drive. Use another Mac to copy the data.

  Step 2

  If you have booted from an external drive, make sure that the internal boot volume is selected in the pane of the system preferences Startup disk.

  Start in safe mode. Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. If you do not see the words "Safe Boot" in the start screen, you did not start in safe mode. Ask for additional instructions.

  Safe mode is much slower to boot and run as normal, and some things don't work at all, including the networks without wire on some Macs.

  The login screen is displayed even if you normally connect automatically. You must know the password for the connection to connect. If you have forgotten the password, you will have to reset it before you begin.

  If the startup progress bar gets stuck for more than a few minutes, or the system stops automatically when the progress bar appears, the boot volume is corrupted and the player is probably defective. In this case, go to step 9. If you have another problem with the player, replace it immediately.

  If you can start and log in in safe mode, empty the trash and then open the window of info on the boot volume ("Macintosh HD", unless you have given it a different name.) Make sure you have at least 9 GB of space available, as shown in the window. If you do not, copy as many files as necessary on another volume (not another folder on the same volume) and delete the originals. Deletion is not complete until you empty the trash again. This, until the space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)

  If the boot process hangs again, the problem is probably caused by third-party software you have installed. Ask for additional instructions.

  Step 3

  If the startup process stops at a gray screen together with a mobile cursor, then the logon dialog box may be active but not visible because of a bug. You may be able to connect by using the arrow keys or the cursor to select the password field and type your password as usual.

  Step 4

  Case of failure of step 3, the boot volume can be complete. If you saw previously implemented guard space drive is low, it is certainly the case. You might be able to start in safe mode , even if you cannot boot normally. Otherwise, boot from an external hard drive, or well technology for step 1b, 1 c or 1 d allows to mount the internal drive and delete some files. According to the documentation from Apple, you need at least 9 GB of free space on the boot (as shown in the Infolog) for normal operation volume.

  Step 5

  If a Mac desktop (without the built-in keyboard) crashes on a gray screen together with a mobile cursor, the keyboard may not be recognized. Hold down the button on the side of a wireless Apple keyboard to make it discoverable. If need be, replace or recharge the batteries. If you use a USB keyboard connected to a hub, connect it to a built-in port.

  Step 6

  Sometimes, a startup failure can be solved by resetting the NVRAM.

  Step 7

  If there is an integrated optical drive, a disk may be stuck in there. Follow these instructions to remove it.

  Step 8

  Press and hold the power button until the unit turns off. Disconnect all devices wired except those needed to start and remove all aftermarket expansion cards. Use another keyboard and/or mouse, if these devices are wired. If you can start now, one of the devices that you disconnected, or a combination of both, the origin of the problem. Discover that it is a process of elimination.

  Step 9

  Launch the utility disk in recovery mode (see step 1). Select the boot volume, and then run the repair disk. If problems are found, repeat until that clear. If disk utility reports that the volume is not repairable, the drive is defective and must be replaced. You can choose to tolerate such malfunction in the reader's life. In this case, delete the volume and restore it from a backup. If the same thing happens again, replace the drive immediately.

  It is one of the rare situations where you must also run repair permissions, ignoring the erroneous warnings, that it can produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.

  Step 10

  If the boot device is an aftermarket SSD, it may have an update and/or a forced "garbage collection". Instructions how to do this with a Crucial SSD of brand have been posted here. Some of these instructions may apply to other brands of SSDS, but you should check with the technical support of the provider.

  Step 11

  Reinstall the OS. If the Mac has upgraded an earlier version of Mac OS X, you need the Apple ID and password used to upgrade.

  Step 12

  Do as in step 11, but this time clear the disk utility boot volume before installing. The system should restart automatically in the installation wizard. Follow the prompts to transfer data from one Time Machine or another backup.

  Step 13

  This step applies only to models that have a battery logic-board ("PRAM"): all of the Mac Pro, MacBook with a removable main battery and a few others (models not updated). A flat battery logic-board may cause a boot failure. In general the failure will be preceded by the loss of the system and boot disk clock settings. Refer to the user manual for replacement instructions. You may need to take the machine to a provider of services to have to replace the battery.

  Step 14

  If you get this far, you probably deal a hardware failure. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• ProBook 455 L3P93ES G2 #ABZ: installation without end and return the video driver AMD R6 and R7 M260DX and stop on a black screen system

  Hello, I'm in trouble with this problem. If anyone can help me, I appreciate a lot. Thank you in advance.

  Laptop: HP ProBook 455 G2 L3P93ES #ABZ

  Problem: windows back AMD R6 and R7 video driver to the old version of windows update install. Return process the screen come black and stop here.

  Procedure, I followed:

  1. updating the bios with the latest version (M75_0141.bin)
  2. new facility created by HP Cloud recovery customer USB boot disk
  3. Install the drivers and programs of the HPSoftwareSetup.exe util
  4. Connect the network cable and upgrade the drivers and the HP Support tool programs assistant
  5. Install the software
  6. Join the Organization's domain
  7. Force Windows Update to version 1607 by the upgrade of Windows tool
  8. Windows Update

  Item 4, at random, windows update 10 and return the driver from these versions:

  • 15.201.1301.0
  • 15.201.2301.0
  • 15.300.1025.1001

  I don't have install the AMD specific video driver (Radeon Crimson Edition 16.7.3 software) or drivers from the Chipset AMD (Crimson edition 16.7.3) because when I try in a previous installation of test I had the same problems

  To restore the display I have to start windows in safe mode and disable the two R6 and R7 display cards, and then restart. After that I can reactivate the cards one time.

  This device first question first time I install Windows 10 the year in August (Yes, after a few days Windows 10 out)

  Any help that will be much appreciate because I have to reinstall on 20 laptops for the school to start the day.

  Thank you

  ScuolaCarovana

  Hello;
  
  Let me welcome you on the HP forums!
  
  From your description, it seems that, after you have installed the correct video driver for your ProBook (15.201.1301) AMD, Windows Update is then by installing a different driver on top of that, right version?

  If this is the case, you must follow these instructions to STOP Windows update update drivers: how stop Windows 10 to update automatically the device drivers - windows Windows 10-10

  Once you do this, you should not see updates to the pilot after that.

  Good luck

• Windows 7 Installation stuck after installing new graphics card

  Before that, my office is fully compatible with Windows 7, but after that I installed a new graphics (ATI Radeon HD 5450) I can't install Windows 7, when I started to install that everything seems fine, but after it restarted and end Installation it just stuck there!

  Any help?
  I tried to remove the new graphics card and the use of the onboard graphics to install Windows 7 still does not work?
  NOTE: I used Windows XP before installing the new graphics card.
  I'm using Acer Aspire M1800
  CPU: Intel Pentium E6300 processor
  Memory: 2 GB DDR2
  Help appreciated
  -Joey

  Hello Joey

  If right now you go back to Windows XP and the system is slow correct? You have the drivers installed since you went back to XP? If not then click here and select your system. This will bring up a list of available drivers for you. Also, I've included a link below to get the drivers for your new video card. My problem with the question is if your system has enough power to support the video card. Here are the specifications of your card. Check the configuration required for the map and you ensure that you have adequate food. Let me know if it helps. Thank you.

  ATI Radeon HD 5450 Windows XP Drivers

• So how can file formatting when installing printer, I return back to their original state.

  Original title: FILE FORMAT CHANGED AUTOMATICALLY AFTER the INSTALLATION of NEW SOFTWARE PRINTER HOW can I RETURN FORMAT ORIGINAL to RECORDS

  I just installed a brother p touch on my computer printer software and now all my folders automatically changed their format to account for the printer. who is a printer for adhesive labels. How can I get all my files back to their original format? I can do each an indivicually, but then, after closing the computer and re opening they come back to the new format of the thumbnail

  Thank you

  but finally managed to solve the problem

  tried to click on all the printers iconc

  except the one on the bar at the bottom of the screen

  from there I could change the default settng for printe

  new sticker fron brother printer

  to the old normal printer

  strange I couldn't do otherwise

• DC Adobe Acrobat installation stuck

  With the help of a MacPro running 10.10.3

  Creative cloud this morning told me there was an update - Adobe Acrobat DC, I clicked on update and the installation started, then stopped to ask leave me an application - do not remember the exact name, but it was something like SafariCloudHelper, I needed to quit smoking via activity monitor. I continued with the installation but its stuck at 35% (and has been for centuries now).

  Tried a restart and everything just go back to square one.

  Any ideas?

  Tri - restarted the activity monitor to leave everything that is coming to Safari (SafariCloudHelper etc.) then ran the Installer - installed very well. Rebooted and everything good.

  Should not have to do it right!

• Flash Player update continues installation stuck at 30%

  I have mac os x and I tried to install a Flash Player update. He downloaded instantly 30% and then got stuck. I tried to install several times force closing safari and ensure no antivirus or firewall blocking the update of the download. I also tried to restart my computer. Later I tried using a program to uninstall Flash Player and Flash Player then put it back in place, but the same thing happened again, stuck on 30%. I have no idea what else I could try and what is happening here. What should I do? My computer is a Macbook Air 2013 OS X Yosemite 10.10.2 version

  Here is the solution! It actually works! How to perform a "clean installation" of Flash Player in Mac OS X

• cannot return back or forward more than one page at a time, what happened to the little arrow that would allow you to go back several pages at a time.

  Some Web sites disable the back button. older versions of firefox, I could hit the little arrow to the right of the forward button and it would display several pages back, so I could choose which one to go backward or forward to. now I'm going back as much as a person with a disability page and cannot go further. It's really annoying to lose a feature that I used all the time

  There are three options to access the history: (1) click and hold the back button. Right (2) click on the back button (3) If you really want installation back, dropmarker one add-on: https://addons.mozilla.org/en-US/firefox/addon/backforward-dropmarker/.

  Hope that helps :)

• Windows 7 installation stuck on windows startup

  I have a laptop pro 64-bit of windows 8.1 and I installed windows 7 ultimate on it, and when I run the installation from the cd it happens to a screen like this and he's stuck there. My laptop is preinstalled with windows 8, then I upgraded to 8.1 pro then have windows 7 ultimate and when I install it it gets to the windows startup screen and does nothing. so, how to solve this problem?

  Decommissioning of laptop computers pre-installed with Windows 8 for Windows 7, you must disable Secure Boot.

  I would recommend that also save your installation before doing so.

  http://techingiteasy.WordPress.com/2012/10/29/how-to-backup-your-Windows-8-installation/

  How to disable Secure Boot:

  Disable secure boot - TechNet - Microsoft