Photoshop quick morning and then slows down

Hey everybody.  I hope someone can help me with this, because I have not found anything on Google.  At least, nothing that works.  When I first go to work every morning, files of large banner I will open very quickly.  However, after about an hour passes, Photoshop is slowing down and everything takes so long to open.  Any ideas on what could be the cause and how can I solve this problem?  Help would be greatly appreciated!

Well Yes, certainly looks like a problem of memory, but if send you information about your system, 32/64-bit, OS, version of Photoshop etc, someone may be able to give you more detailed assistance.

I guess MikeJones11x was talking a SSD (Solid State Drive) in his answer above, and he's right, adding an SSD in a system with you give a boost huge performance, but you have to be careful.

Never use a SSD OS/Apps like your Scratch disk. If you want your Scratch disk on an SSD, install a second, which is what I did in my own system. Another thing to watch out is the controller in an SSD, depending on whether it is used for applications, operating system, or as a Scratch disk.

This is a complicated topic and I will not go into any more detail in this reply, but if you want to study this further please either post a reply here or send me an e-mail, I'll be happy to help if I can.

Good luck

Paul

Tags: Photoshop

Similar Questions

  • Computer gives an error on IPCap.exe two or three times and then shuts down my computer

    Original title : ipcap.exe

    I get an error message on IPCap.exe and it will close. He would make 2 or three times and then shut down my computer.

    Any suggestions?

    Hello

    • What is the exact error message that you receive?
    • What were book them before the problem started?

    You can view these methods:

    Method 1:

    I suggest you make a system full scan just to be sure.
    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

    Method 2:
    I also suggest you to verify the issue in the State of clean boot and check.
    How to configure Windows XP to start in a "clean boot" State

    Note:

    How to configure Windows to use a Normal startup state After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

    1. Click Start and then click Run.
    2. Type msconfig and click OK.
      The System Configuration Utility dialog box appears.
    3. Click the general tab, click Normal Startup - load all services and device drivers and then click OK.
    4. When you are prompted, click on restart to restart the computer.
  • Ping.exe takes a lot of computer RAM and everything slows down

    Original title: ping.exe

    Ping.exe takes a lot of computer RAM and everything slows down. I stop the process, but it comes back. How can I remove it permanently?

    Hello
    I suggest that you try to run the computer analysis online and check if this may help:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Also, try to perform the clean boot and check if it helps:

    http://support.Microsoft.com/kb/310353

    NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

    It will be useful.

  • My Vista crashed and I've switched back to XP. Now I have 1mil more old files compressed that I can't get rid of and it slows down the computer. How can I get rid of these files

    My Vista crashed and I've switched back to XP. Now I have 1mil more old files compressed that I can't get rid of and it slows down the computer. How can I get rid of these files.

    Hello

    1 are. what type of files?
    2. when they are stored?

    3. What is the size of these compressed files?

    Try to perform the clean boot on the computer and check if that helps.

    Reference:
    How to configure Windows XP to start in a "clean boot" State
    http://support.Microsoft.com/kb/310353

    See the bottom of the articles that might help you resolve this problem.
    How to make a computer faster: 6 ways to speed up your PC
    http://www.Microsoft.com/atwork/maintenance/speed.aspx
    Slow PC? Optimize your computer for peak performance
    http://www.Microsoft.com/athome/Setup/optimize.aspx

  • I allowed to install Shockwave Flash in my computer this morning, and then malfunction of the application.

    1. I allowed to install Shockwave Flash in my computer this morning, and then malfunction of the application.  However, I reset my computer and connected only on yahoo.com but I couldn't sign in to other sites like google, wellsfargo and.  I tried to disable this add-on 'Shockwave Flash' managing by module.  Help, please.  Thank you.
    2. Remember - this is a public forum so never post private information such as numbers of mail or telephone!

    Ideas:

    • You have problems with programs
    • Error messages
    • Recent changes to your computer
    • What you have already tried to solve the problem

    Shockwave Flash should not do that. However, if you want to delete it go to programs and features in Control Panel. Click once on Adobe Shockwave Player and click on uninstall in the menu at the top. I suggest you do a comprehensive analysis here, a free service offered by Microsoft. http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  • End of Cup Video Clip off the power when send you first Pro CC 2014 to effects after 2014 CC and I slowed down with Timewarp?

    When I send a clip from Premiere Pro CC 2014 to after effects CC 2014 and I slowed down with Time warp the clip cut of 75% at the end of the video and display only the first 25% slow.  How can I fix this and how I round it travels in first pro to play the FULL slow motion video clip?

    Try adding effect temporal Deformation on an adjustment layer in AFX, rather than on the video it self.

  • How do I remove backup files and they slow down my computer

    I was wondering if the backup of files that are loading down are slowing down my computer how to stop the process and remove

    Hello

    If you think your computer's performance is slow, then it is best to perform a Disk Cleanup. Or see the following Microsoft article and check if that helps.

    Backup and restore: frequently asked questions:

    http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

    Note: If there are several backup files, you can delete files with leaving the last.

    For more information, see the following Microsoft article.

    Optimize Windows Vista for better performance:

    http://Windows.Microsoft.com/en-us/Windows-Vista/optimize-Windows-Vista-for-better-performance

    Hope the information is useful.

  • Process of charms, AppNOS and AppEH slow down my computer.

    The computer of my daughter (a Macbook Pro, processor 2.4 GB, 4 GB RAM, OS x 10.7.5) is so slow. I'm afraid, it was malware. She clicked in some fake malware scan and now it's very slow. The activity monitor shows three processes that eat up memory: AppEH, charms, and AppNOS. If I kill the computer is accelerating. I've already removed some adware that I found, but it is still slow until I have kill these processes. What is? Thanks in advance.

    Pili78

    Download, install, and then run etrecheck. Display the results here so that we can assess which contributes to the slow.

  • "display driver has stoped working, but was recovered" and then shuts down the system. "

    I have a problem with the opening of my yahoo email because my computer just Bonnac outside and flashes once or twice and says "display driver has stoped working, but was recovered" then shuts down the system. " Itsriving crazy me :(     (I have windows vista & pentium bicoeur.)

    This means that there is a problem with your graphics card. I suggest that to update your Windows and check of course latest service pack installed. Also check Windows problem and Solution Center and see if everything suggested installation listed there. It can make it appear to update your graphic card.

    If this isn't the case, try looking in the card of your gaphic provider or your PC support Web site to update its driver.

  • Logitech mouse problems on internet-making a break and to slow down, disconnect some time.

    Problems with internet - take a break and slow down, disconnect some time.  EU here - through diagnostics, connections and modem, Charter signal all very strong.  However, when the Logitech mouse move not, internet does not, it is to say stop connection.  When the mouse moves the internet stream.  Also, during the games if online mouse move not breaks/game stalls.  Someone else, problems with a wireless mouse causing the Internet stopping, jerky?

    Discussions were merged.

    Deleted duplicate.

    Hi Bonnie,.

    Thanks for posting the request in Microsoft Community Forums.

    1. it worked before?

    2. the problem occurs when the wireless mouse is not connected?

    3. using a wireless connection? If so, follow the steps here.

    The issue may be caused by a weak wireless connection or wireless interference. Here are a few troubleshooting steps that you can try to solve:

    -Try to install fresh batteries.

    S ' ensure that the receiver is plugged directly to the USB port on the computer. Avoid using a USB hub.

    -Try different USB ports.

    -Check wireless interference. Check if there is no other wireless devices near the keyboard or receiver.

    -Logitech Wireless Mouse mouse power drain.

    -Remove the batteries.

    -Keep him idle for 10-15 sec.

    -Replace the batteries in.

    I suggest you run the FIXIT from the link below and. If you have already run the fixit, ignore him.

    Hardware devices do not work or are not detected in Windows

    http://support.Microsoft.com/mats/hardware_device_problems/

    If the problem persists, I suggest you to disconnect the wireless mouse and check the results. Also try plugging the same machine to another computer. If you still experience the problem, you may need to contact the Logitech support to repair or replace the unit.

    I also suggest to display the query in Logitech forums for more support information.

    http://forums.Logitech.com/

    Hope this information helps. Response with status so that we can help you.

  • Satellite 1110 series only works for 12 seconds and then powers down

    We have several series of 1110 (Z14 and Z20) laptops and one of them fails to start correctly. Everything works perfectly for 12 seconds, and then it turns off. Each time at exactly 12 seconds.

    Does anyone have any suggestions where I should start looking?

    I've already replaced everything stands (up to the CPU), but without result. There seems to be something inside the motherboard BTK20.

    Thank you

    > There seems to be something inside the motherboard BTK20.

    Seems so if you replaced the common areas like RAM, HARD drive and the processor then the last part would be the motherboard

    But what do you think an overheating problem?
    I mean that the laptop could close because of the higher temperature
    I recommend to check this maybe the thermal grease should be renewed, clean the fans and check again

  • YouTube makes Firefox stutter and it slows down

    In recent weeks, Youtube freezes Firefox (FF) and makes it slow. And even when you leave Youtube, FF keep given the slow and stuttering. Close FF and it again solved the problem. So somehow FF keeps something from Youtube in its system so the entire application is performed.
    I tried to disable add ons, active and have hardware acceleration disabled, active, and disabled the Youtube HTML5. All have no effect.
    In Internet Explorer it works fine, no problems with Youtube at all.

    Hello

    The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.

    Note: This will make you lose all the Extensions, open Web sites and preferences.

    To reset Firefox, perform the following steps:

    1. Go to Firefox > help > troubleshooting information.
    2. Click on the button 'Reset Firefox'.
    3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
    4. Firefox opens with all the default settings applied.

    Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

    This solve your problems? Please report to us!

    Thank you.

  • Why accident to explore Windows vista and mouse slow down when the Panel is open?

    My computer works fine except when I try to open the control panel.  Then windows explore crashes, my mouse is useless and impossible to close the control panel by using the menu of the task.  Everything disappears when I managed to select restart windows Explorer and the closed control panel.  I have seen a lot of messages from people having the same problem but I still see a response that it heals.  Microsoft want money to repair their fault and I'm not ready to feed their greed. If anyone else can help?

    Hello

    What antivirus/antispyware/security products you have on your machine? Include everything you
    ever had including those that you uninstalled. (These can leave leftovers that can cause strange)
    questions.)

    Search all .cpl files most will be in "C:\Windows\System32" However, you can have
    others. Click on each of them at a time and see if it does not start - if so right click on it and
    Rename it using cpZ as the extension is easy to find. Try Control Panel - if no Dungeon of joy
    try all the .cpl files. (Note that other people find other subfolders under C:\Windows should
    not be judged because they are not active.)

    Some of them are appwiz.cpl firewall.cpl, desk.cpl, powercfg.cpl, inetcpl.cpl, timedate.cpl and others.

    Try these in case the General corruption has a role to play:

    Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
    generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    ---------------------------------------

    Icons do not appear in the Control Panel, or you cannot start Control Panel, Windows Welcome, or
    Games in Windows Vista
    http://support.Microsoft.com/kb/936686/en-us

    The Control Panel window will not open in Windows Vista
    http://www.tips4pc.com/articles/Windows%20Vista/control_panel_window_will_not_op.htm

    It was reported a updated driver it has blocked, so have you updated drivers
    lately? Also check the driver updates in Windows Updates.

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • CC of Photoshop crashes regularly and is slow by glaciers at best. When is this corrected? Why I pay for it?

    Since the update in November, both my iMac was rendered almost useless. Photoshop CC 2015 now barely works. When is this corrected? And what is the answer to Adobe? I know I'm not the only complaint to CC.

    Hi mcjohnso,

    Please update your Photoshop in the last update and check if it works.

    Photoshop CC 2015.1.2 update now available

    Kind regards

    Mohit

  • try to load images from sd memory card and it happens errror try again, them I try again and it disappears and then nothing down?

    I put the sd card in the computer when the screen just comes up, I click on open and download. an error comes and says can not find the path. its worked before he leaves me sownpic of computer

    Create a new folder, when AutoPlay appears near

    The letter and drag your sd card is inserted into the drive letter to the new folder.

    Drive letter right-click and select eject.

Maybe you are looking for

  • mail will not send or receive any

    Mail suddenly stopped, send/receive. Updated to 9.3. has worked for a little while then stopped send/receive. I changed nothing. connections to state that they are very well. I can't post to work. Got an exclamation mark in the triangle, clicked on i

  • Sort channels

    Hello I now have the names of channel group: Max Freq offset FREQ Drift FREQ drift rate Offset1 Max Freq FREQ Drift1 FREQ naturel2 drift And when I use the script sort Channel: C:\Program FILES (X 86) \NATIONAL INSTRUMENTS\DIADEM 2014\Examples\docume

  • WindowsUpdate fails to install

    error 8e5e03fa

  • Is Jabber Video for iPad EoL´d?

    I didn t has seen the announcement about the Jabber video for iPad has retired, but the app is more on the Apple Store. I can only find the new 10.5 Jabber, but this one Don t allows to register for the VCS + TMS. A tip how can we download the latest

  • Premiere Pro - out Bit Max depth

    I export from time to time of FADS that have capacities of 12 bits, and I do it through intermediaries that I tend to export through first and Media Encoder. I found this article online on the export capabilities of first and it is said that the firs