Pins of the connector (72) spread over 4 white lined sheets of diagram

Similar Questions

• What type of connections I do for the acquisition of data PCI 619 card pins? What I have to give it to the ground and the CCV on the pins of the connector myself? What should be the value of the SCR I need to give to the PIN?

  I have a PCI 6519 data acquisition card. I want to install it on the PC and use it outputs to control a robot. I have problems with the connections to the terminal block which is attached to the cable.

  What type of connections I do for the acquisition of data PCI 619 card pins? What I have to give it to the ground and the CCV on the pins of the connector myself? What should be the value of the SCR I need to give to the PIN?

  
  

• PIN of the connector broken but the charger works always, safe to use?

  On food, to the end that connects to the computer, the connector is cylindrical with a thin metal rod in the middle. This rod is broken, but taken light goes even when the connector is connected. I can still continue to use the charger or the computer may be damaged? If this isn't the case, I'd appreciate an explanation because I am familiar with electronics. What is the function of the centering pin? The other end has a third PIN to ground. Thanks in advance

  
  

• Concatenate the XY graphs spread over several iterations

  Is it possible to transmit a XY Chart (via a shift register) which generated each iteration to the next iteration and its values is added a graph which lies on the front?

  Yes a waveform graoph. Set x 0 = 0, dx = 0.1.

• How can I check each pin of the connector VHDCI SMU-6548?

  I need to use the VHDCI interface on the slot 3 i.e. NI SMU-6548 NI SMU-1062 q for testing purposes. I need raise or lower the individual lines of the 68 lines available. I use the VISA to do?

  If no VISA, how are NI - HSDIO which are available with the help of LabView 2009 to do? MAX test Panel specifies the channel 0-15 and 16-31. How these channels is linked to 68 lines?

  
  

• Pavilion Notebook 15-ab044sa: load the Pin and the power connector broken

  The computer store where I bought my laptop in August advised that the pin of the connector in my charger is broken and this also broke the load pin in the side of the laptop. The laptop works when it is plugged in but does not load. It is certainly a terrible design of the HP charger fault. Can anyone advice if it's fixable by HP?

  Thanks a lot for your help.

• How the value vias of the connector a specific NET?

  Hi all

  I placed the SMK8R5MIL_B fitting on the top layer of the CCP, which is like 8 slider to pins. The connector is basically will be used in order to connect various energy sources. I can't find a way to assign individual vias of the connector to a specific network. Any help would be greatly appreciated.

  Thank you.

  Hello

  The best way to add a connector is to do in Multisim and then before annotate by selecting transfer > annotate with impatience to Ultiboard.  The PCB design, you are working on that will remain the same, but you will have the connector added in the schema available with all nets installation.  By adding the connector in Multisim synchronize its average will remain your schematic and PCB, adding pieces in PCB design is only bad design practice and in many cases, you will have a lot of problems in the future if you need to make changes to your design.

  If you have not created a schema that you want to assign pins to nets in Ultiboard, select Tools > Netlist Editor, under 'Net', click the menu drop down and select a net, click on the button with an arrow in the picture and then click directly on the axis you want to add to this net, it will be apear on the "Pin" tab.  If the PIN is part of the other net, Ultiobard will not let you select again.

  Yet once, do it in Multisim if you have a diagram.

• Where can I find list of pins for connectors 68 pins on the SMU-8430/8 and the SMU-8431/8

  We need to build new cables for the SMU-8430/8 and 8431/8 interface cards series.

  I can't find pinout information or other connectors 68-pin on the front of these cards.

  Can someone point me in the right direction to find this information.  Thank you.

  The design of the system requires new cables we don't need a list of the pins.

  After a few more watching on the web site of NOR, I found the information I need here:

  http://digital.NI.com/manuals.nsf/WebSearch/F5A76AD1B0C3B1FE86257B59006A9EAD

  Thanks for the reply.

• What is the connector 100 OEM part number used on the PCI-DIO-96 map pins?

  I have a PCI-DIO-96 card and I want to make my own custom cable to connect to the connector of the OID 100 i/o pins.  However, I can't find any reference to the reference OEM of the connector used on the PCI-DIO-96 Board so I can order his companion.

  If anyone knows of any information about the connector part number 100 pins used on the PCI-DIO-96 Board, I would be very happy to know this information.

  Thank you.

  Well, I found earlier the information I was looking for...  Page 1-3 of the PCI-DIO-96 manual (section "Custom wiring").  FYI, I have the March 2009 edition of the manual.  (it helps to actually read the manual, huh?)

  In this section, two OEM mating connectors are suggested:

  Company AMP (P/N 749879-9)

  Honda Corporation (Ref. PCS-XE100LFD-HS)

  I went to the website of the GPA.  There are actually two AMP parts active that do the trick... the P/N given in the PCI-DIO-96 manual map is the non-RoHS connector version.  The compliant version RoHS/ELV of this connector is AMP P / N 5-749879-9.  (Note than the previous one "5" in the part number)

  For the purposes of referral, the connector is a series of 0.050 "SCSI cable insulation Dispalcement Connector [CID] (100 pins to 0.050" Ribbon).

  In the United States, Heilind Electronics (http://estore.heilind.com) carries the AMP part.  Minimum purchase is six parts.  At the time of this announcement, they have a few hundred in stock.

  If all goes well, that helps other readers.

  -Mike

• XFX Radeon 7850 in an XPS 8500 - issue on the connectors 6 pin

  I want to install a Radeon XFX 7850 in a Dell XPS 8500.  I have a question for the two 6-pin connectors.  I need two 6 connectors for this card.  I have two connectors six pins - but both seem to be on the same cable.  Is this right?  I think it is, but I wanted to make sure.  My previous XPS systems have connectors 6 pins on the different power cables... I guess they changed the wiring on these new systems...

  

  Hi oogieboogie_321,

  Yes, you can connect the 6 pins on the card connectors even if they are of the same cable.

• Is there a cable that has a configuration of PIN for the printer and a USB for PC connector?

  I recently bought a HP Pavilion p6620f desktop PC to replace my HP Media Center PC m1270n desktop computer, which has stopped working.  I have a HP OfficeJet K60xi all in one printer fax scanner copier that has been the cable connected to the old PC.  The end of the cable does not match any of the places to go on the new PC.  Can you please tell me how to connect the printer to the new PC?   Is there a cable that has a configuration of PIN for the printer and a USB for PC connector?

  Please see: installation of the product with the USB cable and using the driver from Windows Update or the driver located in the Windows 7 operating system and HP USB 2.0 cable to the printer.

• xw9400: xw9400. Pinout of the need for the connectors of the case (no psu connectors, only those in the case)

  I need the list of pins for various connectors case-Strip pin, especially J24 but other multispindle those too.

  Manual of Tyan S2915 Board for is a different version than that of poor quality that they OEM would be at HP for the 9400 and HP Tech Ref for the 9400 only provides pinouts for connectors well defined including pinout lie anywhere.

  The connector of the Panel before xw9400 J34 (there is no J24) pinout, the mother, is map:

  

  There are 2 key positions (lack of spindle) on pins 10 and 15.  Use these empty pins to help identify the signals.

  The pinout is very similar to other former workstations HP.  A few tips:

  -Pins 1 and 3 are for the harddrive activity led.

  -Terminals 2 and 4 are for the power light.  HP systems have back to back LED connected between these pins.  A green is on and functioning normal and red lights (and flashes error codes) when there are errors.

  -Connect a momentary between pins 5 and 6 switch will turn on the computer and off.

  -Connection of a momemtary between pins 7 and 8 switch will force a system reset.

  -PIN 9 is designated as + 5V, but it is powered by a 100 ohm pullup resistor to + 5V, so it will not provide a lot of power.  FOR INFO.

  -SPKR + and SPKR - are for the internal speaker.

  Most of the other connectors xw9400 follow standards of industry, i.e. the IDE drive and floppy connectors.

  Is there anything else you want to know?

• Z400: Z400 firewire pinout of the connector?

  I noticed that the connector on the front panel 1394 connector 12 pin rather than the standard 10 pin. Does anyone know the pinout? It is not in the maintenance manual. Thank you!

  Here is the pinout of the Z400 J13 1394 header.  Keep in mind that it is looking at the head of the motherboard, and not the connector at the end of the connector to the front panel, which could be a reflection, depending on how you look at the connector.

  The best way to determine the pinout is to use the keyed/missing pins as a refrence.

  

• A question on the single page 'spreads '.

  Hi all. I have a question about indesign that professional designers, could well be very simple.

  I create a menu that will be the A4 (kind of like the letter to the United States)

  However, this menu will be folded in half on the short side to create a thin top menu. The menu will run over two pages.

  Confusion starts now because I need to view the menu in order to know which page goes to the rear from the front. It is because I do have a gap of two pages on one A4 sheet.

  I hope that makes a bit of sense. In essence, I wonder if there is a way to make a document with gaps, which then prints on a sheet of A4, or indeed how printers etc treats it this or if it is not done?

  How could manage the creation of NGO al thin multi menu page that will be printed on A4 (as I need to print)

  Thanks for all tips, I don't know yet what to look for!

  Depends on. On windows, if you have the virtual printer Adobe PDF installed, you can print that. On Snow Leopard, you can print to file, and then distill.

  You can also use a script to impose the pages, then spreads to the export to PDF...

• Having all the icons app pinned to the docking station

  It affect the performance or memory available to other programs if you pin all the application icons in your dock (just for the look)?

  I'm not sure about the memory, but keeping all applications in the dock reduces the execution stack, so it is wise to keep apps in launchpad (you can keep finder and trash in the dock) and also to reduce the size of the icons.

  Thank you!