PIX 515E Version 6.1 (4) a fall port scans

Similar Questions

• Clearing its IPSec on a PIX 515E

  Hello

  Is it possible to delete a particular IPSec security association to a PIX 515E Version 6.3 (1)?

  Concerning

  Lisbeth

  Clear [crypto] ipsec his destination-address spi protocol entry

  is what you are looking for.

• Re: Pix 515E

  Hello

  Pix 515E can configure in some point the port will be opened, after this full time will be automatically closed.

  THX

  concerning

  Gilbert

  Hello

  Please indicate the position, if it has helped you in some way.

  -VK

• PIX 515E for VPN remote site

  Hello

  7.0 (1) version pix

  ASDM version 5.0 (1)

  I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site

  who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success

  The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.

  where can I see the vpn pix for error log?

  is there a manual for the solution of site to site VPN using the wizard

  Help, please.

  Thanks in advance

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a00804acfea.shtml#ASDM

  the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm

  Newspaper to go to the section "check".

• PIX 515E and remote access VPN

  I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.

  I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.

  Any help is appreciated,

  Hello

  Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7

  Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18

  There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue

• PIX 515E-> URL filtering: enabled

  Hello

  When I start my Cisco PIX 515E, I can see this output:

  Cisco PIX Firewall Version 6.3 (3)

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: disabled

  The maximum physical Interfaces: 3

  Maximum Interfaces: 5

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  I understand everything except "URL filtering: enabled".

  I looked in the documentation, but I can't find an explanation: is the PIX can filter requests for URL?

  Thank you in advance for the answer.

  Paolo

  Hi Paolo,.

  6.3 IOS PIX supports filtering of HTTPS and FTP sites to websense filtering servers, this option is enabled by default.

  More information can be found here:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/prod_release_note09186a00801a6d21.html

  and here:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_configuration_guide_chapter09186a008017278e.html#1120209

  Hope this helps-

  Jay

• Question of PIX 515E

  Hi all

  We just bought a PIX 515E and try to use it, but got a number of questions. Here's the NVA of show:

  PIX-151st #show version

  Cisco PIX Firewall Version 6.3 (1)

  Cisco PIX Device Manager Version 3.0 (1)

  Updated Thursday 19 March 03 11:49 by Manu

  PIX-515E up to 5 hours and 15 minutes

  Material: PIX-515E, 64 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0 x 300, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 000f.2457.4b12, irq 10

  1: ethernet1: the address is 000f.2457.4b13, irq 11

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Maximum Interfaces: 6

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Flow: IKE peers unlimited: unlimited

  This PIX has a failover license only (FO).

  Problem is that we cannot ping inner harbor, if we do not switch light, but this is a unique machine. Here's another message once we turn on the switch:

  PIX-515E # config t

  WARNING *.

  Configuration of replication is NOT performed the unit from standby to Active unit.

  Configurations are no longer synchronized.

  PIX-515e (config) #.

  Please help solve this problem. I wonder if we buy the wrong license? Thank you very much.

  you have in your possession a PIX failover. That's why says in the "sh run".

  This device is intended to be used only as a failover for a live device. It will work as a live PIX, but behave badly. It is cheaper than a PIX with an unrestricted license, as it is not intended to be used as a standalone device. Check with the one that you bought to get the situation sorted.

  Good luck

  Steve

• PIX 515E - VPN connections

  Hello

  I have pix 515E and I configured a VPN on it. My users connect to my network from the internet via the Cisco VPN client.

  I have problem, only their LAN machine can do VPN from Cisco VPN client to my network at once.

  Users are connected to the internet via an ADSL router and the LAN switch.

  --------------------------------------------------

  PIX Config:

  6.3 (4) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable encrypted password xxxxxxxxxxxxxxx

  xxxxxxxxxxxxxxxx encrypted passwd

  hostname ABCDEFGH

  ABCD.com domain name

  clock timezone IS - 5

  clock to summer time EDT recurring

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  inside_out to the list of allowed access nat0_acl ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.1.0 255.255.255.0

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside xxx.xxx.xxx.xxx 255.255.255.0

  IP address inside 192.168.1.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool vpnpool 192.168.2.1 - 192.168.2.254

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  Global interface 10 (external)

  NAT (inside) 0-list of access inside_out-nat0_acl

  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server RADIUS (inside) host ABCDE timeout 10

  AAA-server local LOCAL Protocol

  RADIUS protocol radius AAA-server

  Radius max-failed-attempts 3 AAA-server

  AAA-radius deadtime 10 Server

  RADIUS protocol AAA-server partnerauth

  AAA-server partnerauth max-failed-attempts 3

  AAA-server deadtime 10 partnerauth

  partnerauth AAA-server (host ABCDEFG myvpn1 timeout 10 Interior)

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  card crypto client outside_map of authentication partnerauth

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0

  ISAKMP identity address

  part of pre authentication ISAKMP policy 8

  ISAKMP strategy 8 3des encryption

  ISAKMP strategy 8 md5 hash

  8 2 ISAKMP policy group

  ISAKMP life duration strategy 8 the 86400

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 sha hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup myvpn address vpnpool pool

  vpngroup myvpn ABCDE dns server

  vpngroup myvpn by default-field ABCD.com

  splitting myvpn vpngroup split tunnel

  vpngroup idle 1800 myvpn-time

  vpngroup myvpn password *.

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd address 192.168.1.200 - 192.168.1.254 inside

  dhcpd dns ABCDE

  dhcpd lease 3600

  dhcpd ping_timeout 750

  field of dhcpd ABCD.com

  dhcpd outside auto_config

  dhcpd allow inside

  Terminal width 80

  --------------------------------------------------

  Thanks in advance.

  -Amit

  Try to add the "isakmp nat-traversal" command to your PIX. I suspect what happens is that Remote LAN users is translated to a single IP address as they pass through the DSL connection. I also assume that the machine doing the translation has a capacity of IPSec passthrough. Linksys routers would be a good example of this type of NAT device that allows IPSec pull-out.

  If that's the case, that a single VPN connection will be able to operate both. The above command will turn PIX detect clients that are located behind a NAT device, and then try to configure the VPN sessions in UDP packets and so to work around the limitation of NAT and IPSec passthrough device.

• ASDM 5.02 on PIX-515E

  When I use ASDM to administer my PIX-515E (v7.0), I get messages from 2 following error if I update the screen after being inactive in the session for about 2-3 minutes about:

  Error message 1

  ASDM is temporarily unable to communicate with the firewall.

  Error message 2

  ASDM is unable to reach the PIX. Please check the configuration and your connection and try again by clicking the Refresh button.

  These messages were recently and I don't know why. Is there an ASDM idle session time-out setting? I could not found.

  Thank you

  Bill Fanning

  Hello

  What version of Java are you using. If you have Java 1.6, can you go back to 1.5 and see if the problem goes away.

  Also, here is the URL indicating the operating system for client PC and browser requirements

  http://www.Cisco.com/en/us/partner/docs/security/ASA/asa70/asdm50/release/notes/RN505.html#wp231810

  I hope it helps.

  Kind regards

  Arul

  * Please note all useful messages *.

• PIX 515e Install

  I am installing a PIX 515e with an ADSL router. I have all the IP addresses for the router etc. I'm trying to connect to a network on the interface internal of the PIX. (Please bare with me as I am new on the firewall!)

  I ping the network firewall, but I can not access to the internet. The initial configuration for the PIX documentation implies that by default, it has access form the firewall but no! I'm obviously missing something here, i.e. of Thompson the network to route requests through the firewall interent! ???

  Sorry to be so simplistic but I'm learning all the time!

  Thanks for any help.

  Robin

  After you enter the acl to allow ping, can you ping now?

  Watch newspaper reveal something?

  For DNS and testing, create a static on the PIX for your DNS server. For example "x.x.x.x (indoor, outdoor) static 192.168.0.x netmask 255.255.255.255" where x.x.x.x is a public IP address and 192.168.0.x is your dns server. Then let the outside to your DNS server dns - "access-list 101 permit host udp/tcp host x.x.x.x eq 53 z.z.z.z ' where z.z.z.z is a public dns server (or use one for testing) and x.x.x.x IP NAT'ed to your dns server. See what is happening, look in your journal.

  What version of PIX you run.

  Let know use.

  Steve

• Using PIX 515E configuration require

  Dear all,

  Hi.Actually I need help for PIX 515E.Pls. check out the scenario, design & suggest?

  Pls. find the details following and configuration of VLAN attached router.

  # I want to put as

  «Spend my LAN on CISCO 2900 (range 172.16.29.X IP...» (25 PCs) - VLAN router - CISCO PIX - ISP public IP.

  # Now it's

  "My LAN on CISCO 2900 - VLAN (external) router - ISP.

  Details of router & PIX:

  #Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)

  Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)

  #PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)

  #PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)

  Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN

  #I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services

  VLAN router Config:

  Current configuration: 1028 bytes

  !

  version 12.3

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  hostname VLANRouter

  !

  boot-start-marker

  boot-end-marker

  !

  activate the gcsroot password

  !

  No aaa new-model

  IP subnet zero

  !

  !

  no record of conflict ip dhcp

  DHCP excluded-address IP 172.16.29.1 172.16.29.240

  DHCP excluded-address IP 172.16.29.250 172.16.29.254

  !

  IP dhcp pool dhcppool

  network 172.16.29.0 255.255.255.0

  DNS-server 208.144.230.1 208.144.230.2

  router by default - 172.16.29.1

  !

  !

  !

  !

  controller E1 0/0

  !

  controller E1 0/1

  !

  !

  interface FastEthernet0/0

  IP 208.144.230.197 255.255.255.224

  NAT outside IP

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1

  IP 172.16.29.1 255.255.255.0

  IP nat inside

  automatic duplex

  automatic speed

  !

  IP nat inside source list 7 interface FastEthernet0/0 overload

  IP http server

  IP classless

  IP route 0.0.0.0 0.0.0.0 208.144.230.200

  !

  !

  access-list 7 permit 172.16.29.0 0.0.0.255

  !

  Line con 0

  line to 0

  line vty 0 4

  opening of session

  !

  !

  !

  end

  All advice is appreciated.

  Kind regards

  Hiren s Mehta.

  ORG Informatics Ltd.

  Bamako, MALI

  AFRICA

  Hi hiren,.

  See the answers below:

  #Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)

  When you upgrade the PIX router inbetween and your switch, you must put the PIX inside IP like 172.16.29.1 and change the router within the subnet to someother pool. Do the PAT on the PIX, rather than the router.

  Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)

  Router outside the property intellectual property will be that given by the ISP... The ISP would have given a public IP address for the WAN link. This cannot be changed.

  #PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)

  PIX outside IP must be comprehensive. ISP would have given you a LAN subnet. Use it. In this case, inside the interface of the router has an IP address from that subnet even...

  #PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)

  PIX inside must be 172.16.29.1, which will be the default gateway for all PCs. If you change this subnet, then the PC should have an IP address on the same subnet that has decided.

  Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN

  didn't get it... is that on the internet router or switch?

  #I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services

  If all these must be permitted from inside to outside, you have not open anything... by default, all traffic to the inside outside is allowed (except if you put a list of access denied)...

• VPN with ASA 5500 VPN with PIX 515E vs

  I wonder what are the differences between the use of an exisitng PIX 515E for VPN remote users as appossed to acquire an ASA 5500 VPN remote users? Information or advice are appreciated to help me lean toward one or the other.

  Craig

  According to the version of the code that you run on the PIX on the PIX or ASA VPN features must be the same. So if the choice is not based on differences in features, what else would help guide the choice? You can consider if the existing PIX has sufficient resources to add the extra processing VPN load or if you should put that on another box. You might consider that the PIX is an older product range, and his end is near, while the ASA is the product that is the strategic replacement for the PIX. Given a choice I probably prefer to use a technology newer than the old technology. I also believe that the ASA will give you more choice of technology to go forward (a way of better growth) while the PIX provides current capacity but no path of growth.

  On the other hand, there is the aspect of consider that using the existing PIX does not need not to buy something new and ASA would be an expense you have to cover in the budget. And for some people the budget constraint is an important consideration.

  HTH

  Rick

• PIX 515E with 7.1 SMTP banner (2) changed to 220 * how to disable the fix?

  We have a PIX 515E firewall and the SMTP banner is changed to 220 *.

  I need to disable this and I can't use the command "no fixup protocol SMTP" as it is not present in 7.1.

  Any suggestions?

  Kind regards

  Keyvan

  This is done under the map class 'class-map inspection_default' in this version of the PIX OS.

  pls rate if useful!

• License - PIX 515E, restricted or unrestricted?

  How can I know what license I have on a PIX515E? I need to know if it is limited or unlimited. Here is the output of sh worm but nothing jumps on me and said: that which.

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 1.1 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  ABC-FW01 up to 3 hours and 24 minutes

  Material: PIX-515E, 32 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0 x 300, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 000a.b7bc.4b30, irq 10

  1: ethernet1: the address is 000a.b7bc.4b31, irq 11

  2: ethernet2: the address is 0002.b3ad.8176, irq 11

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES: disabled

  Maximum Interfaces: 6

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 806343913 (0x300fd4e9)

  Activation key running: xxxx

  Modified configuration of enable_15 to 10:26:27.064 UTC Tuesday, February 7, 2006

  It is an unrestricted license. The number of maximum interfaces is a way of saying. Restricted is only 3 where UR is 6. You can use this page to see other differences.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_data_sheet09186a00800b0d85.html

  You could also paste your show in output interpreter tool version, if you are a registered user.

  Steve

• Question of BandNew PIX 515E

  I got some new PIX 515E security infra-red and I had sex 2 questions about everything I tried. I installed a 5 port switch inside and cannot ping anything from the console. I have a computer on the switch, and he is able to ping other devices on the switch, but not the PIX.

  What I find strange is that when I try to ping from the inside interface on the PIX of one inside computers, PIX displays the MAC address of the computer inside in the arp table.

  My goal is to upgrade the PIX to ver7.0 but I can't do so until I can solve this problem.

  Here are some information among the PIX.

  #sh worm

  Cisco PIX Firewall Version 6.3 (4)

  Cisco PIX Device Manager Version 3.0 (2)

  Updated Saturday 2 July 04 00:07 by Manu

  pixfirewall up to 29 minutes 33 seconds

  Material: PIX-515E, 128 MB RAM, Pentium II 433 MHz processor

  Flash E28F128J3 @ 0 x 300, 16 MB

  BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

  Hardware encryption device: VAC + (Crypto5823 revision 0 x 1)

  0: ethernet0: the address is 0015.625a.f7da, irq 10

  1: ethernet1: the address is 0015.625a.f7db, irq 11

  2: ethernet2: the address is 000d.8810.902c, irq 11

  3: ethernet3: the address is 000d.8810.902d, irq 10

  4: ethernet4: the address is 000d.8810.902e, irq 9

  5: ethernet5: the address is 000d.8810.902f, irq 5

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES-AES: disabled

  The maximum physical Interfaces: 6

  Maximum Interfaces: 10

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  This PIX has a failover license only (FO).

  #sh run

  interface ethernet1 100full

  nameif ethernet1 inside the security100

  pixfirewall hostname

  domain testlan

  access-list acl_out permit icmp any one

  No external ip address

  IP address inside 192.168.1.222 255.255.255.0

  No IP failover outdoors

  No IP failover inside

  #sh int e1

  interface ethernet1 'inside' is up, line protocol is up

  The material is i82559 ethernet, the address is 0015.625a.f7db

  IP 192.168.1.222, subnet mask 255.255.255.0

  MTU 1500 bytes, BW 100000 Kbit full duplex

  Hi M8,

  Your firewall has a license of FO, you must enable this device to be able to see it.

  Run the command:

  active failover

  With this command, the device turns into the 'Active' from a perspective of failover state. It will work after that.

  See you soon.

  Salem.