PIX 520 meters
SNMP is used to collect counters, if yes, where can I get the MIB information on this? If SNMP is not so used to how the counters are collected?
Specific counter: controlling T-1
Please refer to the SNMP: frequently asked Questions about counters
http://www.Cisco.com/en/us/Tech/tk648/tk362/technologies_tech_note09186a00800b69ac.shtml
To see a list supported (by version), MIB versions see http://www.cisco.com/warp/public/110/pixsnmp.html#mibsupportbyversion
Tags: Cisco Security
Similar Questions
-
Configuration of the PIX 520 with two links to Internet
Hello.
I have a pix 520 with four interfaces ethernet firewall, in fact I am with
just two interfaces,
Ethernet 0 outdoors
Ethernet 1 inside
ethernet2 closed intf2
ethernet3 closed intf3
Thus, in the interface to the outside, I have access to the internet, but now I
access to the internet and I want to configure the two, I mean,.
a single network inside and two internet access,
is it posible?
the perhaps configuration.
Ethernet 0 (access 1) outdoors
1 Ethernet (ip 10.1.1.1) inside
ethernet2 outside2 (access to internet 2)
ethernet3 inside2? (ip 10.1.1.2)?
Thanks for the help,
You can plug it in like that, but there is no way to route traffic by default. PIX does not support this type of connections that you can only configure a default route on the pix. This link should help describe what you can do: http://www.cisco.com/warp/public/110/pixfaq.shtml#Q18
I hope this helps.
Kurtis Durrett
-
PIX 520 running 6.2 (1); SSH session limited exceeded; cannot reconnect
Twice now, one of my PIX 520 s did not allow new ssh or telnet sessions and displays the following message on the syslog server:
PIX-4-315005% SSH session limit exceeded %. Connection request of #. #. #. # on the _interfacename_ interface
I think I understand the basics of what is going on, but I am confused about how to get it for free, and why it has suddenly become a problem.
Both times I went to a physical console (via the nice blue cable) session and used the ssh session disconnect # command. There are 5 numbered 0-4 connections.
Both times that do not release the firewall to serve ssh again.
Help! Anyone have any ideas?
It is a known issue (CSCdy05681 and other I think), must be laid down in the code of 6.2 (2).
-
statements of nat on my PIX 520
I have the following two statements on the config of my PIX 520:
NAT (inside) - 0 100 access list
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
I understand that my predecessor built our Access-list 100 as tunnels for our VPN to our customers. But I don't know what is the purpose of the 2nd NAT.
Pls help...
Education of a nat 0 specifies addresses that will not be translated.
The nat statement 1 by 0 all indicates that any address will lead to a global address. (with the exception of nat 0)
Access-list 100 should be your networking source and destination for the vpn.
-
Gentlemen
Last night I was reading my release notes for my 16 MG ISA Flash card before installing in my PIX 520. The release notes indicate that I have to check if I have a 520 PIX "CO" or "MAKE". A worm show command does not reveal this? I have a small white sticker on the box that says "PIX 520" with no further details.
How can I determine if I have one of these models 'CO' or 'DOING '. It is safe to assume that if she does not, I can go ahead with the upgrade?
Also, I have 2 of these cards to 16 mg. I can put the two or is 16 Cape on Flash... I ask because I want to code ver 6.2.2. In addition to install PDM version 2...
Thank you
Kevin
It usuallt you indicates on the label, but you can tell by the serial number as well.
A0 PIX are between 18005000-18013334
B0 PIX are between 18013335-18015503
C0 PIX are between 18015504-18025676
D0 and E0 are 18025677 and more
Note that there may be a 44 in front of these numbers on your serial number label.
Also note that the installation instructions say the 16Meg card is not compatible with the PIX of C0 (or at least he used to say that), it won't and you can install this card without problem.
Make sure that you first remove the existing 2Meg card, otherwise the PIX will not work. The card is one without the external connectors on it at the back.
You can only put one of these cards in, no need for both. You will be able to load 6.2 (2) and PDM with no problems.
-
I have a PIX-520 and I can't say what type of license is about it. Can someone tell me how to find out? Here's the worm HS:
pixfirewall # SH VER
Cisco Secure PIX Firewall Version 5.0 (3)
Updated Tuesday January 23 00 21:59 by pixbuild
BIOS of finesse V3.3
pixfirewall up to 7 min 42 sec
Material: SE440BX2, 128 MB RAM, Pentium II 349 MHz processor
Flash AT29C040A @ 0 x 300
BIOS Flash AM28F256 @ 0xfffd8000
0: ethernet0: the address is 0090.27a7.2e5f, irq 11
1: ethernet1: the address is 0090.27a7.2d88, irq 10
Licensed connections: 65536
Serial number: 18021002 (0x112fa8a)
pixfirewall #.
Hello
I remember, Pix 520 came in 3 licenses of connection, 128, 1024 and 65536. 65536 is a unrestricted license option. Since your worms Sh shows connections that are allowed as 65536, your Inbox is unrestricted.
-
3DES throughput of PIX 520?
Hello
Anyone know what is the PIX 520 3DES throughput? (No VPN accelerator card)
Thank you
Hi Oneill,
As PIX520 EOL, it took me a bit of searching to find it, so I hope this helps you...
http://www.Cisco.com/warp/public/cc/PD/FW/sqfw500/prodlit/963_pp.htm
Software and hardware encryption
Version 5.0 (1), with the addition of the appropriate encryption key, provides encryption based on the software for THE (56-bit) and 3DES (168-bit), as support for the acceleration OF only using the PL2 existing (PrivateLink) map. Users can expect to see a minimum of 10 to 20 Mbps of throughput for 3DES connections and 30 to 40 Mbps of throughput for using encryption based on PIX software. Customers who use the card PL2 can expect to double their throughput OF. NOTE: The PL2 card does NOT support 3DES encryption. In addition, the low number for above mentioned 3DES throughput is for the 515 PIX with a 200 MHz processor, and the high number is for 520 PIX with a 350 MHz processor.
Kind regards
Abdelouahed
-=-=-
-
PIX 520 &; 6.3 (5) worm.
We have some Cisco PIX 520 firewall
And, we want to update its version for more later... 6.3 (5), is it possible?.
Thank you.
No problem for version 6.3 (5) don't forget but version 7.0.
Release notes:
PIX 520 requirements: 16 MB (Some PIX 520 units possibly an upgrade of memory because the older models had 2 MB, although newer units have 16 MB)
http://www.Cisco.com/en/us/products/sw/secursw/ps2120/prod_release_note09186a00804e6d6d.html#wp31988
http://www.Cisco.com/en/us/products/sw/secursw/ps2120/prod_release_notes_list.html
sincerely
Patrick
-
Unable to BREAK/ESC to switch to Monitor Mode on the PIX 520
Hi all
I'm moving to PIX704.bin... I tried Copy TFTP FLASH and it fails with a space. So when I try to recharge, I'm never invited to the command BREAK/ESC. Here is the result:
Reset...
Cisco Secure PIX Firewall BIOS (3.6)
Startup disk
Flash = @ 0 x 300 i28F640J5
Read 1962496 bytes of the image of the flash.
################################################################################
384 MB OF RAM
mcwa i82559 Ethernet to irq 11 MAC: 00d0.b78f.2ee8
mcwa i82559 Ethernet on irq 10 MAC: 00d0.b78f.2b56
Flash = @ 0 x 300 i28F640J5
Flash BIOS = AT29C257 @ 0xfffd8000
Is it possible that the BIOS is too old? Any help would be greatly appreciated...
Glad it helps. On the 520, you use a boot disk not the break sequence. Normally, you would use the tftp command to load the most recent versions of the firewall operating system anyway. You can see the following link for more information.
I hope this helps.
Steve
-
Fleeing from a host on the PIX 520 but alerts that are still coming to the IDS
Last week I saw allot of traffic from a particular host that triggers alerts IDS. After investigating the source, I added a statement SHUN to the pix. When I do a 'sho shun stat' of the NTC for this host is quite high (352) and rises. I still get alerts of the IDS on this particular host (Fragment IP and host sweeps). I guess if I was fleeing from an IP address, I don't receive alerts of IDS on that. Can someone explain what I am doing wrong? Thanks in advance.
Seems obvious, but can't hurt to ask - where the sniff of your sensor interface? Of course, if your sniffing interface is located outside the pix, then junk traffic will always reach the pix - it just won't be through it.
In addition, are fleeing this host for these alarms? Doing a show 'show shun' that host being blocked FOR the time you see alerts for this particular host?
Jeff
-
Can I allow outside users to connect to an IP address on the inside with the help of NAT I need to establish a connection with a DCOM application and apparently it does ' t work with NAT.
Thank you
To establish a connection between the external and internal interface interface, you need a static and an ACL. The static method CAN map the IP address of the host to himself, effectively bypassing NAT, but this means that the internal host must have valid Internet a routable IP address.
For example, assume that your internal host has a 209.1.2.3 Internet address, your config might look like:
> static (inside, outside) 209.1.2.3 209.1.2.3 netmask 255.255.255.255 0 0
> list of allowed inbound ip access any host 209.1.2.3
> interface incoming group-access outside
Of course, you should make sure that 209.1.2.3 is routed to your PIX.
-
PIX 520 IP Addressing question.
My 520 has 2 Ethernet ports. I can ip outside interface (E0) 170.1.111.1 255.255.255.255 and IP inside (E1) 170.1.111.2 255.255.255.0. If this is not the case, how can there be two interfaces on the same subnet. I want to use the 520 as a firewall in an enterprise WAN packet filtering. Inside boxes will have an ip address in the range of 170.1.111.0.
These are not my real IP addresses *.
Its called multinetting, if I'm not mistaken, and no, you can not multinet, i.e. having same subnet on different interfaces on the same device.
-
Error during removal of command in pix 520
rtpmap 1 ipsec-isakmp crypto map
! Incomplete
If you want to remove this command, use the command "no card crypto rtpmap 1"
Kind regards
Arul
* Please note all useful messages *.
-
That means Type 3, Code 1?
Type 3 (host unreachable)
Code 1 (?)
Hello
'type 3' (inaccessible) is a kind of ICMP¨packet. ' Code 1 means 'host unreachable '. Take a look at this URL for more information:
http://www.Cisco.com/en/us/products/SW/iosswrel/ps1831/products_tech_note09186a00800a6057.shtml
Kind regards
Tom
-
I am facing convert statements leads on our PIX 520 access lists. Is there a better way to do this will be as little as possible traffic interruption? For example, to create access lists and then remove the conduit, or vice versa?
Second, is there a priority recommended in order to access list?
Hello
This is a very good paper on the conversion of lines to the ACL, also when writing ACL always have your most important ACL on top of the ACL work from the top down. When you make changes to the ACL or static lines always issue the command clear xlate and save with RAM command.
http://www.giac.org/practical/GSEC/Bill_Donaldson_GSEC.pdf - by Bill Donaldson, GSEC.
If you want more information/inf, then let me know.
Thank you / Jay.
Maybe you are looking for
-
Re: Satellite L300 - screen turn off when it will be moved
I have a problem with my screen stopping when I move my laptop or move the screen slightly. The computer does not turn off just the screen becomes black. I have to then hold the power button to turn off the computer. Does anyone has any ideas or had
-
ENVY 14-j013tx: HP, laptop ENVY 14-j013tx DIMM and memory Max Support
Hello Nobody knows how many Slot DIMM and Max Memory Support for this portable version (ENVY 14-j013tx)? Thanks for your advice.
-
Hello any ideas when powershell for vWorkspace 8 will be available? Or are there other features of the API? We need automate the creation of group, creating Application, user assignment etc. Thank you jeje
-
Foglight dashboard access to colleagues
It's on dashboard foglight sharing with colleagues. I myself remember during training Foglight tutor provided a way to change the below url so that everyone can access and No need to connect to the foglight requests access to the dashboard. http://>
-
When entering passwords a pop up keeps appearing.
Whenever I go to enter a password a pop up appears (Please enter the master password for the software security device) it affect me not login to any site I'm on, but it is very irritating. Any ideas on the origin, or particularly how get rid of it,