PIX log specific IP or Protocol

Similar Questions

• Need recommendation for PIX logging software

  Hello

  I need a recommendation for a PIX software logging so that I can better manage my PIX 525 and 515 firewall. I am currently using Cisco Syslog and I want something that I can set up specific, priority alerts, send email or page... etc. Your help would be most appreciated.

  Thank you

  You can use: KIWI Syslog

  http://www.kiwisyslog.com/software_downloads.htm#download%20Now

  Commercial products:

  Cisco VMS = http://www.cisco.com/go/vms

  Sawmill = http://www.sawmill.net/

  IQR = http://www.eiqnetworks.com/products/products.shtml

  sincerely

  Patrick

• PIX log messages

  Can someone direct me to a document that explains what that 'type' and 'code' values average associated log PIX messages?

  You can search for codes on google and icmp types.

  ICMP type 3 is Destination Unreachable 1 Host Unreachable code

  See link below http://livenudefrogs.com/~anubis/icmp/

• How Pix manages the rare IP protocol packets

  Does anyone know of a document explaining how the Pix handles, regarding the State, rare IP protocol packages such as ESP, AH, OSPF, GRE, etc. ? I'm concred with traffic flowing through the pix is not intended.

  I understand how TCP, UDP, and ICMP packets are handled, but I can't find anything on all others.

  Thank you.

  In General, the Pix must inspect any protocol passes through it accepts for TCP and UDP. The exception is a protocol which is managed by a '' correction '' like PPTP which has a correction to allow GRE (Protocol 47) traffic that results.

  If you want a different protocol than UDP/TCP to be allowed to get THROUGH, you almost create an ACL entry for her.

  The other exception is the traffic to the Pix itself as host. ACL have absolutely no effect on the traffic to the Pix as the host. For example, the packets OSPF intended for the Pix when running OSPF. Or packages ESP for the Pix for a VPN tunnel, it stops. Or ICMP traffic to the Pix itself (controlled using the command [icmp]). ACL don't apply to transit traffic.

• How to see the pix log information

  environment like this:

  PIX 7.0 are configed for logserver.

  PFS install on Windows XP.

  How can I see the information of the newspaper of pfss.did anyone have this experience.

  The log files are stored in the \Program Files\Cisco\PIX Syslog server to default firewall or any other directory you have installed PFS in. Search for files with the .log extension.

• in pix 6.3 ios routing protocols (3)

  6.3 (3) support also TEAR apart from ospf, otherwise how is among the warnings is RIPv2 mcast updates are sent through an interface that does not have any rip has helped this topic.

  Hello

  PIX 6.3 code supports the two RIP (v1 and v2) and OSPF. The disadvantage is that you cannot configure the RIP and OSPF on the same PIX. You must choose the one that you want to use. I hope this helps.

  Scott

• Download connection for VPN log

  Logging and diagnostics of the VPN connection are a total waste of time - even after clearing logs and the connection that once, there are tens of thousands of lines of newspapers. Diagnose insists, of course, that everything is fine. By clicking Help, takes you as usual, a totally independent place - I got 30 results for "troubleshooting." What has to do with VPN, I guess Microsoft could say.

  Can I get a simple log that shows the protocols and parameters that were considered along with the results? As the old modem component logs?

  Seems they were too advanced a feature for the Member States to implement in a bare back and compact OS like Win 7... / sarcasm

  PS That is him go with not being able to open the settings window? Or connect to two connections at the same time? Or check the status of the underlying network when connecting? Fever of the modal dialog again?

  If you watched to where newspapers to find errors?

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  You or the VPN server admins looked at the logs from the server using VPN?

  If it is a PPTP VPN connection?

  Don't forget you must forward/open the TCP 1723 Port through the firewall or the router, the server behind. The firewall or the router also need to be able to pass traffic GRE protocol 47. This is sometimes called PPTP pass through or VPN Pass Through or is configured automatically when the TCP 1723 Port is open on the firewall or the router.

  Test the VPN path using the PPTP Ping and VPN traffic sections on this page...

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  http://Windows.Microsoft.com/en-us/Windows7/why-am-I-having-problems-with-my-VPN-connection

  Troubleshooting VPN connections...

  http://blogs.technet.com/b/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx

  Troubleshooting Vista VPN page that may be of little help...

  http://blogs.technet.com/b/rrasblog/archive/2007/04/08/troubleshooting-Vista-VPN-problems.aspx

  Additional help in TechNet Windows 7 Pro forums...

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

  .. .or the appropriate instance of Windows Server...

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• site2site distance-VPN and access-PIX - no way?

  I have,

  I have a problem wrt site2site & VPN remote access on a PIX:

  My setup is as follows: PIX (6.3) puts an end to two a site2-site VPN and also should the remote access service clients using the client VPN Cisco (4.0.x).

  The problem is with remote access VPN clients, obtain an IP address on their VPN interface, but customers cannot reach anything. (Please note that the site2site VPN runs without problem)

  To be precise (see config-excerpts below):

  The customer, who has 212.138.109.20 as its IP address gets an IP 10.0.100.1 on his card-VPN which comes from the "vpnpool of the pool.

  configured on the PIX. This customer relationships to reach servers on interface 'inside' of the PIX as 10.0.1.28.

  However, the client cannot achieve * nothing *-a server on the inside or anything like that (e.g. Internet) outside!

  Using Ethereal traces, I discovered that the packets arrive inside interface coming 10.0.100.1 (IP address of the)

  VPN - client). I also see the response from the server (10.0.1.28) to 10.0.100.1. However for some reason any package does not thanks to

  the PIX to the customer. PIX-newspapers also show packets to and from the VPN client to the inside interface - and * no. * drops. So to my knowledge the packets from server to the VPN client really should be done through the PIX.

  I have attached the following as separate files:

  (o) the parts of the PIX config

  (o) packets showing PIX-log between the VPN client and the server (s) on the interface inside

  (o) ethereal-trace done inside the watch interface also packets between VPN client and server (s)

  I have really scratched my head for a while on this one, tested a lot of things, but I really don't know what could be a problem with my

  config.

  After all, it really should be possible to run site2site - and on the same PIX VPN remote access, shouldn't it?

  Thank you very much in advance for your help,.

  -ewald

  I think that your problem is in your ACL and your crypto card:

  access-list 101 permit ip 10.0.1.0 255.255.255.0 10.0.2.0 255.255.255.0

  access-list 101 permit ip 10.0.0.0 255.255.255.0 10.0.2.0 255.255.255.0

  access-list 101 permit ip 10.0.3.0 255.255.255.0 10.0.2.0 255.255.255.0

  access-list 101 permit ip 10.0.1.0 255.255.255.0 10.0.100.0 255.255.255.0

  correspondence address 1 card crypto loc2rem 101

  This means that this map correspond to these addresses. But your dynamic map is one that must match 10.0.100.0, 10.0.1.0 traffic because your pool local ip is 10.0.100.x. I think what is happening is that the return traffic from the lan to vpn clients trying to get out of the static tunnel, which probably does not exist (for the netblocks - you probably have a security association for each pair of netblocks, but not for vpn clients) and so do not.

  I would recommend adding these lines:

  access-list 105 allow ip 10.0.1.0 255.255.255.0 10.0.2.0 255.255.255.0

  access-list 105 allow ip 10.0.0.0 255.255.255.0 10.0.2.0 255.255.255.0

  access-list 105 permit 10.0.3.0 ip 255.255.255.0 10.0.2.0 255.255.255.0

  no correspondence address 1 card crypto loc2rem 101

  correspondence address 1 card crypto loc2rem 105

  Then reapply:

  loc2rem interface card crypto outside

• VPN concentrator + PIX on LAN-> customers can not reach local servers

  Hello

  I have a problem wrt. remote access clients coming via a VPN3000 concentrator and trying to access local servers.

  For the topology:

  The internal network is 10.0.1.0/24. It connects with the outside world, as well as via a PIX DMZ; the PIX has 10.0.1.1 in the internal network.

  On the same LAN (internal), I have the VPN concentrator for the inside address 10.0.1.5. It assigns addresses in the 10.0.100.0/24 range to the

  VPN client-PCs.

  I can sucessfully connect using the VPN client SW to the hub, i.e. remote access clients out addresses

  the 10.0.100.0/24 range.

  The problem: access from VPN clients to internal network is * not * possible; for example, a customer with 10.0.100.1 cannot connect to

  internal to the 10.0.1.28 server.

  To my knowledge, this is a routing problem because the server (10.0.1.28) has no idea on how to reach customers in

  10.0.100.0/24. The only thing that the server is a default static route pointing to the PIX, i.e. 10.0.1.1.

  So I set up a static route on the PIX for 10.0.100.0 pointing to the hub-VPN, that is

  Mylan route 10.0.100.0 255.255.255.0 10.0.1.5 1

  This does not solve my problem though.

  In the PIX logs, I see the entries as follows:

  % 3 PIX-106011: deny entering (no xlate) tcp src trainee: 10.0.1.28 (atlas) / 445 intern dst: 10.0.100.1 (pending) 1064

  The PIX seems to abandon return packages, i.e. traffic from the server back to the client

  To my knowledge, the problem seems to be:

  Short traffic VPN - client-> Concentrator VPN-> Server-> PIX - where it gets moved.

  My reasoning: the PIX only sees the package back, i.e. the package back from the server to the client - and therefore decreasing the

  package because he has not seen the package from the client to the server.

  So here are my questions:

  (o) how do I configure the PIX that I be connectivity between my remote VPN clients (10.0.100.0/24) and

  computers servers on the local network (10.0.1.0/24)?

  (o) someone else you have something like this going?

  PS: Please note that the first obvious idea, installation of static routes on all machines on the local network is not an option here.

  Thank you very much in advance for your help,.

  -ewald

  Hello, PIX the because can not route traffic on the same interface (prior to version 7.0 anyway), I suggest you two places your hub to the outside with the inside of the legs on a zone demilitarized or (if you can not do a makeover of the network) you remove your pool with 10.0.100.0 - addresses and create a pool with 10.0.1.0 - addresses which is a part of the address space. No, NOT all. A little book that it is not used inside.

  Best regards

  Robert Maras

• Pix 515E, VERY basic question

  I just pulled the thing out of the box and he turned on.

  I put it on our internal network plugged a laptop inside interface and went through the Setup Wizard.

  I gave the external interface a static address, said pat for internal systems (just the laptop listed above), and all seemed well.

  He already seems to be an access rule that allows all outbound traffic, but I can see something beyond the inside interface (192.168.1.1) on the laptop.

  I ping around the world since the pix, but the poor internal system sees nothing.

  I am very new to Cisco and am sure I'm missing something basic.

  Anyone want to help our a beginner?

  Thank you!

  Hello

  You can watch the traffic on any interface by applying

  the folloving command

  capture (capture name) int (interface name)

  through the show (name of capture) capt command you

  See the packets captured on this interface

  Example: I want to watch the traffic on the inside of the interface

  In capture tony type mode interface privileged (#) inside the

  then see tony snapshot

  In this case, you should see incoming ICMP echo packets to the laptop. (I don't think they come, I guess you don't have the road to the 192.168.0.0 network (or just default to 192.168.1.1 - and only road!) in your laptop). Try the road print on laptop computer command to check.

  ICMP commands in your configuration are not ACL commands, they control only ICMP join the PIX

  interfaces, no ICMP by PIX.

  So I don't think that you can successfully ping

  192.168.0.111 ICMP echo packets, but should leave

  the PIX outside interface and the response to the ICMP echo

  192.168.0.111 packets would be arrested to that

  return ping interface. This could be seen in

  PIX log (see the logg). You must start logging in configuration by

  conf t

  LOGG on

  LOGG buff 7

  You can also apply the capture on the external interface.

  To get the return of packages 192.168.0.111 ping, you must apply a list of access on the external interface of the PIX. As written in the previous post.

  HTH

  Zdenek

• NetBIOS (UDP 137) causing the 'noise' in Syslog PIX

  Our PIX logs are loaded to deny reports about udp port 137 vehicles coming from our servers to Win, it makes it difficult sometimes to see the other messages to refuse, we must investigate.

  Disabling NetBIOS over TCP/IP on servers is unfortunately not an option for us in this VLAN individual. The infrastructure underlying is a Catalyst 6500 switch and we wonder if there is a way, using its feature set, to filter traffic entering the port of the PIX. We want to block the port UDP/137 so drop packets unwanted before the PIX are same.

  We have looked into VACL but aren't aware of their ability, ACL, MAC address, traffic at a lower level. In this interface PIX and servers are in the same VLAN Layer2, we do not have a Layer 3 interface we can use to apply an ACL.

  Everybody deals with this issue, any suggestions?

  Hello

  to make the operation forest op NetBIOS disappear, you have the option to create a list entry access that matches the netbios traffic and disables logging for this entry. At the end of the access list entry simply add "disable the log."

  This feature requires OS PIX v6.3.

  Kind regards

  Tom

• FTP PASV - Pix or 1605R?

  I need support a client connection to our FTP server that uses a PASV connection. We have currently a 1605 with the IP option router base, and it does support the dynamic ACL.

  It seems that my option is either to replace by a PIX 501 and implement "fixup protocol ftp" or upgrade our router in 1605 in support of CBAC, in which, according to me, I need IP/FW. The router has flash 4 MB, 16 MB of DRAM, but I think I have a 8MB flash range.

  There is no other traffic through this connection with the exception of this FTP transfer. What is the best option? Upgrade our 1605 or buy a PIX?

  Thanks in advance.

  Two things-

  1. you don't need to "permit tcp host (outside IP address) host (local ftp server ip) eq ftp - data '. The reason is that CBAC is inpecting ftp traffic and it will open the appropriate ftp-data port.

  2 passive ftp does not use port 20. Active FTP does.

  See this link for a better explanation.

  FTP active vs. passive FTP, a definitive explanation

  http://SlackSite.com/other/FTP.html

  Hope that helps! If Yes, please rate.

  Thank you

• Reset network protocol Bind order

  Hello

  It is said:

  If more than one protocol must be installed on the server, you can give the Protocol most frequently used by the highest priority of Oracle database by resetting the binding order of network protocol.

  
  

  Is TCP protocol used by Oracle?
  

  Win 2008 Server How can I do this?

  
  

  Thank you.
  

  Reference?

  And with the Protocol, in that layer, as defined by RFC 1122 - Requirements for Internet Hosts - Communication Layers, are you?

  And usually, we installed an IP (Internet Protocol) stack. This contains a number of protocols. See InternetProtocolFamily - the Wireshark Wiki.

  What and where is this "magicks" you speak of are thus binding priority? Especially since one SPECIFICALLY select the Protocol when creating a raw IPv4 socket. or an IPv4 socket interface?

• This protocol uses Agent to communicate with the Service

  Hello everyone, this is my first post in this forum and I want to shoot a question if someone could help me.
  
  I guessed that the communication between the api and the server at the time where the user will put api HQAPi = new HQApi (...) is with the http or https protocol, depends on the value introduced in the conf file.
  
  I would like to know what protocol uses agent to communicate with the service. I would like your ideas.
  
  Thanks in advance.

  Hello

  Welcome to the forums!

  Could you clarify your question a bit more? Looking for agent-> server HQ communication or agent-> communication monitored service?

  If this is an agent-> HQ server then they communicate with each other using foam which is a specific HQ communication protocol.

  If he's an agent-> monitored service it depends on the service.