PIX501 customer VPN - cannot access inside the network with VPN Session

Similar Questions

• ASA 5505 VPN established, cannot access inside the network

  Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.

  After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.

  Here is my config:

  ASA Version 8.2 (5)
  !
  hostname asa01
  domain kevinasa01.net
  activate 8Ry2YjIyt7RRXU24 encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  switchport access vlan 5
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan5
  No nameif
  security-level 50
  IP 172.16.1.1 255.255.255.0
  !
  passive FTP mode
  DNS server-group DefaultDNS
  domain kevinasa01.net
  permit same-security-traffic intra-interface
  Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
  inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
  inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
  sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
  access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
  access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
  pager lines 24
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (outside) 1 192.168.254.0 255.255.255.0
  NAT (inside) 0 access-list sheep - in
  NAT (inside) 1 192.168.1.0 255.255.255.0
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.5 - 192.168.1.36 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  WebVPN
  internal Remote_Kevin group strategy
  attributes of Group Policy Remote_Kevin
  value of server DNS 192.168.1.12 192.168.1.13
  VPN - connections 3
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
  kevinasa01.NET value by default-field
  username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
  username kevin attributes
  VPN-group-policy Remote_Kevin
  type tunnel-group Remote_Kevin remote access
  attributes global-tunnel-group Remote_Kevin
  address-pool
  Group Policy - by default-Remote_Kevin
  IPSec-attributes tunnel-group Remote_Kevin
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  inspect the icmp error
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
  : end

  Thank you

  Hello

  I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.

  I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.

  The acl must be:

  sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0

  For nat (inside), you have 2 lines:

  NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
  NAT (inside) 1 0.0.0.0 0.0.0.0

  Why are you doing this nat (outside)?

  NAT (outside) 1 192.168.254.0 255.255.255.0

  Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)

  Thank you.

  PS: Please do not forget to rate and score as good response if this solves your problem.

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James

• Control access to the network with ACS device

  Hi all!

  I currently have in place an Appliance, Cisco Secure ACS using Windows as main server authentication. Cisco Secure acts as a GANYMEDE server +. I have two groups defined in Cisco Secure: Netadmins and security ITD. Users of the Netadmins group need access to all switches and routers on the network. ITD security must only access async line 53 on a router 2611 for a band of a firewall and no other access to all network devices offline. How can I limit access to the Cisco Secure security ITD group to line 53 only?

  My current config on this router is:

  AAA new-model

  AAA authentication login netadmins group Ganymede + line

  connection ITDSEC authentication group Ganymede + line of AAA.

  RADIUS-server host 10.30.X.X

  RADIUS-server host 10.18.X.X

  key radius-server XXXXXXX

  line 53

  No exec

  authentication of the connection ITDSEC

  transport of entry all

  StopBits 1

  Speed 115200

  line vty 0 4

  exec-timeout 30 0

  login timeout 120 response

  login authentication netadmins

  but users in the ITD security can still access by vty and then reverse telnet to any asynchronous line on the router. In addition, security ITD always access any switch or router using telnet: what should be my setup on these devices? I do an ACS configuration?

  All other devices:

  AAA new-model

  AAA authentication login netadmins group Ganymede + line

  RADIUS-server host 10.30.X.X

  RADIUS-server host 10.18.X.X

  key radius-server XXXXXXX

  Line con 0

  password 7 141C015C5806

  login authentication netadmins

  line vty 0 4

  password 7 11020A 524310

  login authentication netadmins

  line vty 5 15

  password 7 11020A 524310

  login authentication netadmins

  Any help will be greatly appreciated.

  Hello

  In the security group, I would create a Restriction of access to IP network with an entry permit. Essentially to allow access to the single port on 2611 only.

  The AAA Client field is the name that you gave to the 2611 in the network config. Address will be * unless you want to restrict access to the ip or address. Port... never quite sure with async if the port value must be "async 53" or "line 53".

  If you look in the pass/fail for the nas-port attribute, you'll see what that T + sends to the ACS. This should help you know what to put in the NAR.

  Mounira

• ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x

  Hello

  I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside.

  If anyone can share some light... There's got to be something escapes me...

  Here's my sh run

  Thank you

  Raul

  -------------------------------------------------------------------------------

  DLSYD - ASA # sh run

  : Saved
  :
  ASA 9.1 Version 2
  !
  hostname DLSYD - ASA
  domain delo.local
  activate the encrypted password of UszxwHyGcg.e6o4z
  names of
  mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
  !
  interface GigabitEthernet0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/1
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/2
  Post description
  10 speed
  full duplex
  nameif Ext
  security-level 0
  IP 125.255.160.54 255.255.255.252
  !
  interface GigabitEthernet0/3
  Description Int
  10 speed
  full duplex
  nameif Int
  security-level 100
  IP 192.168.255.2 255.255.255.252
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  clock timezone IS 10
  clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
  DNS lookup field inside
  DNS domain-lookup Int
  DNS server-group DefaultDNS
  192.168.1.90 server name
  192.168.1.202 server name
  domain delo.local
  permit same-security-traffic intra-interface
  network dlau40 object
  Home 192.168.1.209
  network dlausyd02 object
  host 192.168.1.202
  network of the object 192.168.1.42
  host 192.168.1.42
  dlau-utm network object
  host 192.168.1.50
  network dlauxa6 object
  Home 192.168.1.62
  network of the 192.168.1.93 object
  host 192.168.1.93
  network dlau-ftp01 object
  Home 192.168.1.112
  dlau-dlau-ftp01 network object
  network dlvpn_network object
  subnet 172.16.1.0 255.255.255.0
  the object-group Good-ICMP ICMP-type
  echo ICMP-object
  response to echo ICMP-object
  ICMP-object has exceeded the time
  Object-ICMP traceroute
  ICMP-unreachable object
  DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
  Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
  DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
  Ext_access_in access list extended icmp permitted any object-group Good-ICMP
  Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
  Ext_access_in list extended access permit tcp any object dlausyd02 eq https
  Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
  Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
  Ext_access_in access-list extended permitted ip object annete-home everything
  pager lines 24
  Enable logging
  asdm of logging of information
  MTU 1500 Ext
  MTU 1500 Int
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 713.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
  !
  network dlausyd02 object
  NAT (Int, Ext) interface static tcp https https service
  dlau-utm network object
  NAT (Int, Ext) interface static tcp smtp smtp service
  network dlauxa6 object
  NAT (Int, Ext) interface static tcp 444 444 service
  network dlau-ftp01 object
  NAT (Int, Ext) interface static tcp ftp ftp service
  Access-group Ext_access_in in Ext interface
  Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
  Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  AAA authentication enable LOCAL console
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  LOCAL AAA authentication serial console
  the ssh LOCAL console AAA authentication
  http server enable 44310
  http server idle-timeout 30
  http 192.168.0.0 255.255.0.0 Int
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec pmtu aging infinite - the security association
  trustpool crypto ca policy
  Telnet 192.168.1.0 255.255.255.0 management
  Telnet timeout 30
  SSH 192.168.0.0 255.255.0.0 Int
  SSH timeout 30
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  No ipv6-vpn-addr-assign aaa
  no local ipv6-vpn-addr-assign
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 61.8.0.89 prefer external source
  SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
  WebVPN
  port 44320
  allow outside
  Select Ext
  AnyConnect essentials
  AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_DLVPN group strategy
  attributes of Group Policy GroupPolicy_DLVPN
  WINS server no
  value of server DNS 192.168.1.90 192.168.1.202
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DLVPN_STAcl
  delonghi.local value by default-field
  WebVPN
  AnyConnect Dungeon-Installer installed
  time to generate a new key 30 AnyConnect ssl
  AnyConnect ssl generate a new method ssl key
  AnyConnect ask flawless anyconnect
  encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
  vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
  username admin password encrypted tFU2y7Uo15ahFyt4
  type tunnel-group DLVPN remote access
  attributes global-tunnel-group DLVPN
  address pool DLVPN_Pool
  Group Policy - by default-GroupPolicy_DLVPN
  tunnel-group DLVPN webvpn-attributes
  enable DLVPN group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the netbios
  Review the ip options
  inspect the ftp
  inspect the tftp
  !
  global service-policy global_policy
  SMTPS
  Server 192.168.1.50
  Group Policy - by default-DfltGrpPolicy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:67aa840d5cfff989bc045172b2d06212
  : end
  DLSYD - ASA #.

  Hello

  Add just to be sure, the following configurations related to ICMP traffic

  Policy-map global_policy
  class inspection_default
  inspect the icmp
  inspect the icmp error

  Your NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other.

  I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured?

  Can you same ICMP the directly behind the ASA which is the gateway to LANs?

  If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA

  Int Management-access

  As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN.

  -Jouni

• ASA 5505 VPN cannot access inside the host

  I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.

  framework for configuration below

  interface Vlan1

  nameif inside

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Crypto-map dynamic inside_dyn_map 20 set pfs

  Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map

  inside crypto map inside_map interface

  crypto ISAKMP allow inside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  global service-policy global_policy

  XXXXXXX strategy of Group internal

  attributes of the strategy group xxxxxxx

  banner value xxxxx Site Recovery

  WINS server no

  24.xxx.xxx.xx value of DNS server

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  by default no

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout no

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  the address value xxxxxx pools

  enable Smartcard-Removal-disconnect

  the firewall client no

  WebVPN

  url-entry functions

  Free VPN of CNA no

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  tunnel-group xxxx type ipsec-ra

  tunnel-group xxxx general attributes

  xxxx address pool

  Group Policy - by default-xxxx

  blountdr group of tunnel ipsec-attributes

  pre-shared-key *.

  Missing nat exemption for vpn clients. Add the following and you should be good to go.

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

• Client VPN cannot get inside the network

  The VPN client connects to the 2600 on the serial interface, should be able to get to the 10.10.0.0 network beyond 192.168.1.14. The customer ping responds failure of external serial interface address.

  If you still have problems... can you check that there is a static route BOF 192.168.100.0/24 on router 192.168.1.14 and initiate a tracert to a host on the network of 10.10.x.x at 192.168.100.7 and see where it goes... your tests show that the VPN client knows how to get to this subnet, but it seems that there is a problem of routing between 10.X.X.X going 192.168.100.0

  I hope that helps!

• Cannot access inside the ASDM on PIX

  Hi all:

  I can't access the ASDM on the PIX when I type in

  Any advice would be appreciated.

  Hold on, I'm reading a release on bail of ADMS, which may have a fix for this problem.

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsv12681

  [edit]

  CSCsv12681 Details of bug

  Symptom:

  During the loading of ASDM, a dialog box appears that says:

  "Failed to load ASDM. Click OK to exit ASDM.

  Sockets without link not implemented. "

  This happens when you use Java 6 Update 10 or later.

  Conditions:

  ASDM version 5.0 or later running on ASA, PIX or FWSM and using Java 6

  Update 10 or later.

  Workaround solution:

  Use Java 6 Update 7.

  1 found-In

  5.0 (8)

  5.1 (2)

  5.2 (4)

  6.1 (5)

  4,0000 F

  1.0000 F

  Fixed in

  6.2 (0.70)

  6.2 (0.71)

  6.1 (1.55) F

  5.2 (4.51)

  6.1 (5.51)

  You can use this version based on report above.

  ASDM - 61551.bin

• Comments Win XP cannot connect to the network when Cisco VPN works on Mac

  Guest OS (Win XP) on the merger connects to the network, no problem. However, when I start a Cisco VPN on my Mac (not in the guest operating system) and then start Fusion/guest OS, the guest cannot connect to the network.

  I was able to use this configuration for a year on an old MacBook Pro (unibody). Last month, I got a new MacBook Pro and flying over my virtual machine image. I don't check for a few weeks. I'm sure I fly over the image correctly because everything else seems OK or if the IT guys doing something to block my traffic over the VPN.

  Config

  -Fusion - Version 3.1.0 (261 058)

  -Mac - 10.6.4

  So far, I have tried the following

  -started to merge and XP without VPN on Mac - OK (bridge autodetect)

  -launched VPN to work, and then launched Fusion - no network

  -tried ipconfig/release, ipconfig / renew - not always no network

  -tried NAT - do always no network

  Thanks in advance. For any help or suggestion will be greatly appreciated.

  Bernie

  The NAT value and then restart the virtual machine.  Works for me with the VPN client built into a cisco router.

  Do not work the real on 10.6.4 cisco software unless you really need to.

• ASA 5540 - cannot ping inside the interface

  Hi all. We have recently upgraded PIX to ASA5540 and we saw a strange thing going. In a Word, we can ping the inside interface of the ASA from any beach on our 6500 network (which is connected directly behind the ASA on the inside), but one where our monitoring tools are placed. Inside there is an ACL that allows all of our core networks, but it does not help that the interface is really strange.

  In the ASDM, I see messages like this:

  ID ICMP echo request: 2004 x.x.x.x y.y.y.y on the inside interface to. I don't think that's the problem, but I could be wrong.

  This is also the configuration of the interface VLAN VIRTUAL local area network from which we cannot ping inside the interface we can ping to and since this VLAN and machines without problem. The only problem is ping the inside interface of the ASA.

  interface Vlanx

  IP x.x.x.x 255.255.255.0

  IP broadcast directed to 199

  IP accounting output-packets

  IP pim sparse - dense mode

  route IP cache flow

  load-interval 30

  Has anyone experiences the problem like this before? Thanks in advance for any help.

  Can you post the output of the following on the ASA:-

  display the route

  And the output of your base layer diverter: -.

  show ip route<>

  HTH >

• vSwitch ESXi 5.1 workaround to virtual machines (direct access to the network)

  Hello world!

  I have a server running properly the 5.1 ESXi hypervisor and got inside the physical grid active router with DHCP. How can I configure the vSwitch on ESXi 5.1 work not managed on the network, without VLAN and have direct access to the network?

  Just to clarify, I would like to first of all virtual machines VMware Workstation works - if it is possible to run several virtual machines and define all NICS (Network Interface Card) as connected by a bridge, that is to say. Each VM gets the specific configurations of IP to the external router.

  Since now, thank you very much for the help!

  Best regards

  Eduardo

  With ESXi the vSwitches work comparable to Bridged networking, so there is really nothing special to do.

  André

• From Firefox blocks all access to the network

  When I start Firefox (41.0.1), all access to the network is completely blocked. Before you start the FF, I can access the Internet (with Chrome or IE), other computers, but as soon as I launch Firefox, all access to the network (including the connection to other computers) is blocked. In addition, my computer will turn off more.

  As far as I KNOW, I have not installed lately extensions or add-ins.

  Thank you for your resolution. Today, when I mentioned to work, I was told to update Firefox. This seems to do the trick (so far, fingers crossed!).

  (https://support.mozilla.org/en-US/kb/refresh-firefox-reset-add-ons-and-settings) so very probably an extension is causing harm.

  When this isn't ' t the resolution, I will surely return to your resolutions.

• Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail.

  Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail. I tried to clear the cache and restart Firefox, but I still cannot use Hotmail.

  Not this problem when I go to Internet Explorer.

  Hello, it was noted that the foxit pdf plugin is causing this issue. You can disable this plugin in firefox > addons > plugin until what foxit offers a patch/update for the plugin.

• HP Pavilion with Win 10 - cannot connect to the network

  Hello

  I have a HP Pavilion (M2N68 - THE motherbaord) the computer has been upgraded to windows 10 and working fine but something happened and I have no access to the network. Under control panel / network connection, I have a grayed on "Boardband Connection" icon and a "connection to the Local network' who says"network cable unplugged. " Player in an eathernet cable has no effect.

  I also checked in the Device Manager and there is no warning or errors.

  Normally I would check and updated the motherbaord drivers but the original drivers for this PC model are supported only up to Windows 7.

  I don't know that that then check. Please help me ill take what I have to do to re - connect my desktop to my network.

  Thank you

  _Asher

  Hi there @AsherE,

  I hope you find your experience of positive Support Forum!  I understand that you are having problems with any type of network connection to your computer. I'm happy to help you with this.

  Please report the number of complete product for your computer. Check out the following, if you need assistance with this information. HP desktop PC - how can I find my model number, serial number or product?

  When you plug an Ethernet cable, is there a clear link on the LAN adapter and/or the activity light flashing?

  Have you tried another port on the router?

  Are able to connect to your router using another device cable connection or WiFi connection?

  Have you tried another Ethernet cable?

  A power cycle you the router?

  Please let me know when you can.

• Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  Dear Sir

  Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  I am in a field & I'll migrate with a domain name.

  EX: now I'm in the field of the AAA tomorrow my domain name will change to BBB. User accounts are created in two AAA & BBB and the two domain user IDs are different.

  data servers are also migrating with the new domain.

  is it possible to access share with the old user id folder in new field or both to share the files again with the new user ID Active directory.

  Kind regards

  Chauvet J.

  Hello

  The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/