Port-channel problem: SP-5-CANNOT_BUNDLE_LACP

Similar Questions

• Port-channel problem between fabric Interconnect and vPC N7K

  Hi all

  I have a problem with the Port Uplink channel between fabric interconnect with N7K using vPC

  It's my network for the UCS deployment topology

  

  N7K I configured vPC for red link and green linkto the fabric Interconnect A I has configured the Port-Channel with Member is Port 1 and Port 2, uplink is red link. Interconnection fabric B, I have configured the Port-Channel with Member's Port 1 and Port 2, uplink's green link.

  The interface port-channel on N7K show is good, each port-channel upwards and have all members. But the fabric Interconnnect, when I see in the UCS Manager, the status of the Port-Channel on Fabic A and fabric B dysfunction not more info: no operational Member. Although all the link is a link to the top and I've got the status of the Port Channel is enabled in the UCS Manager. When I see the properties Port 1, Port to Port-Channel 2, I see the number of members status is: individual. This means channel port is not up and no member in this configuration. I want to using the port-channel load balance and more bandwidth for the uplink of 20Gig. I don't understand why?

  Please help me solve this problem, I have to send the screenshot of UCS Manager when I show the status of the Port-Channel and Port-member in port-channel to reach items.

  Can someone help me solve this problem, thanks a lot. References, please include elements for more details on the fault.

  Thank you

  Trung.

  Hello Nguyen,

  Since the two N7k please collect:

  SH cdp nei

  SH run membership in. X int

  SH sum port-chan

  Thank you

  Matthew

• PORT-CHANNEL PROBLEM

  I have configured ports-2ch (in18 PO19) linking (CAT6) and 8 interfaces of HP Blade to Catalyst 6509. When configuring noted that the catalyst 6500 created "subinterfaces' as shown below:

  SWCRJ-CORE #show etherchannel summary
  Charge for five seconds: 3% / 10%. a minute: 5%; five minutes: 5%
  Time source is NTP, 14:35:31.640 BRV Tuesday, December 21, 2010

  Flags: - Low P - D bundled in port-channel
  I have - autonomous s - suspended
  H Eve (LACP only)
  R - Layer 3 S - Layer2
  U - N running - is not in service, no aggregation
  f cannot allocate an aggregator

  M not in use, no aggregation due to minimum links has not met
  m don't use, port do not associate due to not meeting minimum links
  u - unfit to tied selling
  d default port

  w waiting to be aggregated
  Number of channels: 33
  Number of aggregators: 39

  Protocol for the Port-Channel port group
  ------+-------------+-----------+-----------------------------------------------
  1 Po1 (SD)-
  2 Po2 (SU) - Gi1/3/14 (P) Gi2/3/14 (D)
  3 Po3 (SU) - Te1/1/1 (P) Te2/1/1 (P)
  4 (SU) Po4 - Te1/1/2 (P) Te2/1/2 (P) Te2/2/3 (D)
  Po5 (SU) 5 - Gi1/3/9 (P) Gi2/3/9 (P)
  Po6 (SU) 6 - Gi1/3/7 (P) Gi2/3/7 (P)
  7 in7 (SU) - Gi1/3/5 (P) Gi2/3/5 (P)
  8 in8 (SU) - Gi1/3/10 (P) Gi2/3/10 (P)
  9 Po9 (SU) - Te1/1/3 (P) Te2/1/3 (P)
  10 Po10 (SU) - Te1/1/4 (P) Te2/1/4 (P) Te2/2/4 (D)
  11 Po11 (SU) - Gi1/3/8 (P) Gi2/3/8 (P)
  12 in12 (SU) - Gi1/3/6 (P) Gi2/3/6 (P)
  13 Po13 (SU) - Gi1/3/11 (P) Gi2/3/11 (P)
  14 Po14 (SU) - Gi1/3/12 (P) Gi2/3/12 (P)
  15 in15 (SU) - Gi1/3/13 (P) Gi2/3/13 (P)
  Po16 (SD) - 16
  Po17 (SD) - 17
  18 in18 (SU) LACP Gi1/9/25 (P)
  18 Po18C (SU) LACP Gi1/9/28 (P)
  18 Po18A (SU) LACP Gi1/9/26 (P)
  18 Po18B (SU) LACP Gi1/9/27 (P)
  Po19 (SU) 19 LACP Te1/1/8 (D) Te2/1/8 (D) Gi2/9/25 (P)
  Po19B (SU) 19 LACP Gi2/9/27 (P)
  Po19C (SU) 19 LACP Gi2/9/28 (P)
  Po19D (SU) 19 LACP Gi2/9/26 (P)
  20 Po20 (SU) - Gi1/3/15 (P) Gi2/3/15 (P)
  50 Po50 (SU) - Te1-2-1 (P) Te1/2/2 (P)
  51 Po51 (SU) - Te2/2/1 (P) Te2/2/2 (P)
  52 Po52 (SU) - Gi1/9/11 (P) Gi2/9/11 (P)
  53 Po53 (SU) - Gi1/9/12 (P) Gi2/9/12 (P)
  54 Po54 (SU) - Gi1/9/13 (P) Gi2/9/13 (P)
  55 in55 (SU) - Gi1/9/14 (P) Gi2/9/14 (P)
  In60 (SU) 60 LACP Gi1/7/31 (P) Gi1/7/33 (P) Gi1/7/34 (P)
  Gi1/7/35 (P)
  Po61 (SU) 61 LACP Gi2/7/31 (P) Gi2/7/32 (P) Gi2/7/33 (P)
  Gi2/7/34 (P)
  62 Po62 (SU) - Gi1/3/16 (P) Gi2/3/16 (P)
  63 Po63 (SU) - Gi1/3/17 (P) Gi2/3/17 (P)
  64 in64 (SU) - Gi1/3/18 (P) Gi2/3/18 (P)
  100 Po100 (RU) - Te1/5/4 (P) Te1/5/5 (P)
  101 Po101 (RU) - Te2/5/4 (P) Te2/5/5 (P)

  I tried a lot of combination but no joy. Currently, it is the configuration of interfaces:

  Interface Port-channel18
  Description blade 3 Modulo1
  switchport
  switchport access vlan 666
  switchport trunk encapsulation dot1q
  switchport trunk vlan native 987
  switchport trunk allowed vlan 505,506,1100-1109,1170
  switchport mode trunk
  switchport nonegotiate
  events-the link status logging
  MLS qos trust cos
  end
  ==============

  interface GigabitEthernet1/9/25
  Description blade 3 Modulo 1 Porta 21
  switchport
  switchport access vlan 666
  switchport trunk encapsulation dot1q
  switchport trunk vlan native 987
  switchport trunk allowed vlan 505,506,1100-1109,1170
  switchport mode trunk
  switchport nonegotiate
  events-the link status logging
  MLS qos trust cos
  passive mode of channel-group 18< already="" tried="">

  spanning tree portfast edge

  ====================

  Interface Port-channel19
  Description blade 3 Modulo2
  switchport
  switchport access vlan 666
  switchport trunk encapsulation dot1q
  switchport trunk vlan native 987
  switchport trunk allowed vlan 505,506,1100-1109,1170
  switchport mode trunk
  switchport nonegotiate
  events-the link status logging
  MLS qos trust cos
  end
  ========================

  Description blade 3 Modulo 2 Porta 21
  switchport
  switchport access vlan 666
  switchport trunk encapsulation dot1q
  switchport trunk vlan native 987
  switchport trunk allowed vlan 505,506,1100-1109,1170
  switchport mode trunk
  switchport nonegotiate
  events-the link status logging
  MLS qos trust cos
  passive mode of channel-group 19< already="" tried="">
  spanning tree portfast edge

  The blade only configured LACP and priority 100 on all interfaces.

  No one knows no measures to remedy this situation?

  Kind regards

  Raphael

  Hello Raphael,.

  When using LACP and you see a port-channelA, B, C, etc., those are called secondary aggregators and this means that LACP is enabled on the remote port, but something is causing it is impossible to combine with the main channel.  This is usually caused by receiving ID system is different from the other side by having the interface cable between multiple devices.

  First thing I would do, is to ensure that all wiring is correct and that all the ports in in18 and po19 go just a switch for each port-channel.

  -Matt

• Configuration port-channel, DTP, disabling

  Hi all

  I had a problem on the day where I wanted to attach a pile of 3750 x 2 to the network, the core is a 6500.

  There was a link configured for the core of the 3750 he had the configuration necessary trunk with BPDUFILTER active

  at the end of the base he had the standard configuration of trunk. The link is on the rise and work.

  Went to get a second battery for the heart link. Decided that DTC must be turned off at the end of the SWITCHPORT NONEGOTIATE battery

  the normal chest on the port configuration on the port channel port joined. Then suddenly the newspapers went crazy and right now, I need

  Spanning tree went crazy and started blocking areas of the network to avoid loops. There is STDS running in the network

  I had similar errors to this % SW_MATM-4-MACFLAP_NOTIF

  I pulled the battery cables and all services affected later came back.

  I know that enable the BPDUFILTER option stops at the port to participate in STP.

  Please could someone confirm due to the incompatibility of the config on these ports it has this problem or is there something I missed here

  Thank you mnay

  The BPDU filter is the root of the problem.

  You can't have two active rising running without creating a loop, unless they run into a PaGP/LACP-EtherChannel configuration. By having one or two links running with a filter BPDU, spanning Protocol tree on the 6500 didn't know that a link had to be in a deadlock state and he was panicked when MAC addresses on the stack of 3750 began to stir between interfaces.

  3750 cross media - stack EtherChannel using LACP, so if you want the resilience of two connections without having to factor in the covering tree branches, it is a good idea to combine the two in a group of channels and have both the 3750 and 6500 treat them as a single logical connection.

  If you want to keep them separated, you will need to remove the filters BPDU these ports and leave spanning tree figure things out properly.

• Setting port channel between UCS - FI and MDS 9124 (Mode F)

  Dear team,

  We tried to create the channel of port between UCS FI and MDS 9124

  But the port channel do not take action in mode F on MDS 9124

  FI is in host FC end Mode

  We have allowed FC uplink on FI trunking

  We have activated NPIV on MDS

  We have activated the MDS trunk

  FI and MDS in default VSAN

  To check that we have changed the way FI FC channels mode and switch port became active, but in E mode

  When we enabled CF trunking of uplink on the port mode FI channels and FC Switching became active in mode TE

  but in both cases above, showflogi database shows WWPN of SAN alone does not have the any fi.

  How to achieve this?

  Have read that no need to change the mode switching mode of CF swicthing and keep FC Endhost way

  SO how to channel ports with mode F MDS and FI (Display Mode as NProxy)

  What is it has nothing to do with the MDS NX - OS version? (https://supportforums.cisco.com/thread/2179129)

  If yes how to put as license for ports came with the camera and we don't have any CAP/PAK or license file as she came

  with license

  Also, we saw 2 files available for download (m9100-s2ek9-kickstart - mz.5.2.8 .bin and m9100-s2ek9 - mz.5.2.8 .bin b b) to use

  Thanks and greetings

  Jose

  Hi Jo Bo.

  What version of the software if your MDS race?

  On your UCS do connect nxos and show ficelleStringString ficelleT inteface and find the mac address.

  It is possible that you could be hitting the bug below. If this is the case, you may need to update the firmware on your MDS.

  Add MAC YES '002a6a', '8c604f', '00defb' for 5 k/UCS-FI

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCty04686

  Symptom:

  Link change cannot connect any other Nexus or other Cisco Switch in mode VAN with a port channel F.   Question can be viewed in older versions of 5.1

  5.1.3.N1.1a

  but not later

  5.1.3.N2.1c

  Release. Question is also found in

  5.2 (1) N1 (1)

  and

  6.0 (2) N1 (1)

  and later versions.

  Conditions:

  Nexus configured for the link SAN PortChannels or NPIV Nexus mode connected to the UCS via regular F port channel where UCS VAN VAN edge mode switch: YES switch manufactured FI or another Cisco UCS Port WWN: xx:xx:00:2 has: 6a: xx:xx:xx or xx:xx:8 c: 60:4f:xx:xx:xx

  Workaround solution:

  Turn-off on Nexus 5 k TF-port question link mode does not happen with standard F-PORT SAN to remove Portchannel config

  Other Description of the problem:

  To check question collect please see the flogi-event history internal errors whenever the port is attempted OLS, AMENDMENTS, PBA counters will increment. This can be determined via the following output, view port internal info to see all the internal-historic port of error events

• SH cdp neighbors port-channel command

  Hello

  I have a strange problem with the command sh cdp neighbors port-channel on my 3750 and 4500switches.

  When I execute the command ' sh cdp neighbors port-channel. I don't see my say on this interface.

  The command 'sh cdp nei' with the port-channel works very well and shows all my neighbors.

  switch #sh cdp neighbors port-channel 1

  Ability code: R - router, T - bridge Trans, B - road Source bridge
  S switch, H - host, I - IGMP, r - Repeater, P - phone.
  D / remote, C - AEVC, M - two port Mac relay

  Device ID Local Intrfce Holdtme Port platform capability ID
  

  switch #sh ether summary
  Flags: - Low P - D bundled in port-channel
  I have - autonomous s - suspended
  H Eve (LACP only)
  R - Layer 3 S - Layer2
  U - running f - cannot allocate an aggregator

  M - don't use, minimum contacts not satisfied
  u - unfit to tied selling
  w waiting to be aggregated
  d default port

  Number of channels: 1

  Number of aggregators: 2

  Protocol for the Port-Channel port group
  ------+-------------+-----------+-----------------------------------------------
  1 Po1 (SU) LACP Gi1/0/1 (P) article gi1/0/2 P)
  

  I tried the command on multiple versions of IOS, but always the same question. When I try the command on a 6506-E, it works fine...

  This ordering platform is connected?

  SWITCH2 # sh etherchannel summary
  Flags: - Low P - D bundled in port-channel
  I have - autonomous s - suspended
  H Eve (LACP only)
  R - Layer 3 S - Layer2
  U - N running - is not in service, no aggregation
  f cannot allocate an aggregator

  M not in use, no aggregation due to minimum links has not met
  m don't use, port do not associate due to not meeting minimum links
  u - unfit to tied selling
  d default port

  w waiting to be aggregated
  Number of channels: 7
  Number of aggregators: 7

  Protocol for the Port-Channel port group
  ------+-------------+-----------+-----------------------------------------------
  1 Po1 (SU) LACP Gi1/1 (P) Gi1/2 (P)
  ...

  SWITCH2 #sh cdp nei port-channel 1
  Ability code: R - router, T - bridge Trans, B - road Source bridge
  S switch, H - host, I - IGMP, r - Repeater, P - phone

  Device ID Local Intrfce Holdtme Port platform capability ID
  switch to Gig 1 / 2 123 S I Gig 1/0/1
  switch to Gig 1 / 1 123 S I Gig 1/0/2
  

  Thank you

  Best regards

  Joris

  Hi Joris,

  It is a known problem and is documented as a cosmetic bug internal. Logically speaking, CDP is not supported on etherchannel interfaces and 'sh cdp port-channel' command should not be available.

  The platform of 6500, although the "port channel show cdp neighbor" returns the result, it's just for convenience and does not mean that the CDP is supported on the port channels. In fact, if you try to enable CDP on port-channel on 6500, it generates an error:

  PO1 #int 6500 (config)

  6500(Config-if) #cdp en

  % CDP is not supported on this interface, or for this encapsulation

  If you run "debug cdp events", you can see the packets exchanged on the physical interface rather than on the port-channel. Correct way is to check the neighborship of the cdp on the physical interfaces.

  See you soon,.

  Shashank

  Please rate if you find the content useful

• prolific usb-to-serial com port driver problem. I can't load the driver from propper for her. What should I do?

  prolific usb-to-serial com port driver problem. I can't load the driver appropriate for that. What should I do?

  Hello edmcski,

  This thread has been created in the Feedback forum. the Microsoft moderation team has moved this thread on the forums of hardware and drivers.

• See the bandwidth for the Port-Channel on Powerconnect &amp; Force10

  Reference Dell dear community,

  Y at - it a command CLI or GUI to see how much bandwidth result after having done a port channel in some port Powerconnect and Force10? Suppose we have 4 port 1 Gb and do 4 ports with 1 port-channel. So actually in this channel port have a bandwidth of 4 GB.

  In Cisco, with the command show interface port-channel 1, we get the result

  switch #sh po int 1
  Port-channel 1 is up, line protocol is up (connected)
  Material is EtherChannel, address is 0064.4026.739a (bia 0064.4026.739a)
  MTU 1500 bytes, BW 4000000 Kbit, DLY 10 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  KeepAlive set (10 sec)
  Full duplex, 1000 Mbps, link type is auto, media type is unknown
  input stream control is turned off, output flow control is not supported
  Members in this channel: Gi0/1 Gi0/2
  Type of the ARP: ARPA, ARP Timeout 04:00
  Last entry of 00:00:00, 00:04:48 output, output hang never
  Final cleaning of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0
  Strategy of queues: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 2000 bps, 3 packets/s
  5 minute output rate 2000 bps, 3 packets/s

  But if we do this command on Powerconnect, the just result inform port that starts from the port-channel.

  Reference Dell #show interfaces port-channel 1 short

  Ch-Type Hash Type Min-links Channel ports local FRP
  -------   ----------------------------- -------- --------- --------- ---------
  PO1 Active: Static disabled people article gi1/0/1, gi1/0/2 7 1 article
  Item in gi1/0/3, item in gi1/0/4

  Type of hashing algorithm
  1 - the source MAC, VLAN, EtherType, source module and port Id
  2 - destination MAC, VLAN, EtherType, module source and port Id
  3 - source IP and TCP/UDP source port
  4 - destination IP and destination TCP/UDP port
  5 source/Destination MAC, VLAN, EtherType, MODID/source port
  6 source/Destination IP and port TCP/UDP source / destination
  7 - improved hash mode

  Can you help us find the answer?

  Thank you

  Kind regards

  Aziz

  The PowerConnect switches do not have the ability to show as much detail as the Force10 can. The RMON tables have an interface use %, what may be the closest we can do on the PowerConnect switch.

  #show rmon statistics

  I've seen some monitoring software which was able to question the switch via SNMP and get some information of bandwidth. However, this can be a bit inconsistent, according to which switch and what software is used.

  The MIBs/OID can be downloaded with the software switch.

  http://www.Dell.com/support/home/us/en/rc959303/products/ser_stor_net/networking/net_fxd_prt_swtchs

• FC Port-Channel does not

  Hello

  I need help, I'm setup CF port-channel between 9148 MDS and Cisco fabric Interconnect 6248 and the port-channel does not work. He said no operational members.

  For the MDS, see configuration below:

  NPIV #feature SW (config)

  SW (config) #feature fport-channel-trunk

  SW (config) #interface fc1/17-18

  SW(config-f) force Group-channel mode # 63

  SW(Config-if) F #switchport mode

  SW(Config-if) #switchport trunk-allowed vsan 1-2 (I have only vsan 1 and 2)

  SW (config) #no close

  SW (config) #interface 63 port channel

  SW(Config-if) F #switchport mode

  SW(config-f) #switchport trunk-allowed vsan 1-2

  SW (config) - #no close

  Note: the ports are assigned to vsan 2

  See the attached screenshots for interconnection fabric config

  On the fabric of interconnections switchport mode are defined E. What I have to change to F. If yes where can I change since the option is not there in the UCS Manager?

  have you added the VSANS on the UCSM as well?

  What Code are you runnig on the San Norhbound selector?

  You can be hitting

  https://Tools.Cisco.com/bugsearch/bug/ CSCty04686

• Total for the port-channel when speed config speed 1000-nexus5548?

  Hello world.

  now I connect cisco 6509 and nexus 5548up using two link of 1000M and I want the two link port-Channel binding.

  5548up port 10GE port cisco 6509 is 1GE, I config speed 1000 in nexus5548 ethernet port, and I find

  the speed 1000 order auto config interface port-channel, so I would like to know the total speed in this channel port

  is 1000M and 2000M when port-channel speed config 1000? I appreciate your help!

  the topology like this:

  1000M

  --------------------------------------------

  6509 port-channel speed 1000M nexus5548UP

  ----------------------------------------------

  1000M

  Hi again

  The speed of the links and portchannel is 1000M but the bandwidth of the portchannel is 2000M

• MDS configuration for port channel

  I tried to put in place the new download FC port channel to a pair of 9124 s MDS, but as I don't know enough on the side MDS, I can't the link to come. Are there references available anywhere say you blow by blow exactly how to set up the side MDS of the channel of the port? Or maybe an example of configuration work?

  Thank you

  I don't think it's possible to configure the fabric of interconnections, FC switch mode that only VAN is based on those. The only mode of switch that is taken in charge and possible to configure is the local network Ethernet switching mode.

  I have configured the week last on a pair of 9124 s MDS and needed to activate the F port trunking and channeling Protocol feature by using this command

  "feature fport-channel-trunk.

  After that, I had to run SAN Port Channeling. Here's a snipit of my configuration:

  npiv functionality
  fport-channel-trunk feature

  interface port-channel 11
  active channel mode
  rate switchport dedicated mode

  interface fc1/1
  port-license purchase
  Channel-Group 11
  no downtime

  interface fc1/2
  port-license purchase
  Channel-Group 11
  no downtime

• Fabric Port Channel

  Hello

  Once in production, when the addition of cables in a PortChannel from fabric between the IOM and a FI, first had to be re - ack frame? (so that we will have the chassis package downtime). Or rather, as is a Port-Channel cables are detected automatically, so that it is not necessary to re - ack, and so there is no downtime in all... one that is the correct statement?

  Thank you

  Hello

  Yes, it is possible to have cloth by fabric port channel (A / B) by within an instance of the UCS chassis.

  Option is available under

  Equipment > chassis > chassis X > connectivity strategy

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/GUI/config/Guide/2.0/b_UCSM_GUI_Configuration_Guide_2_0_chapter_01100.html#d106201e585a1635

  HTH

  Padma

• UCS - san-port-channel on vpc

  Hello

  I hope someone can help with this,

  I have a Setup with 2 Nexus of 5548 connected via a link of vpc peers and a keepalive, these two nexus switch have a link of standard VPC to a 6500 upstream. It works fine,

  Then, there are several native FC connections of the 5548 to of 6248. I know that there is the possibility to configure the channel port of CF on the UCS 2.0 but it is possible to link 5548 CF interfaces in a port channel san through a vpc between the nexus of 5548.

  so, for example, I can port-channel which follows through a vpc or is a channel of port san, limited to the same nexus only switch ports.

  Fc1/31 & fc1/32 fabric sent to-> NX5K - 1 Port fc1/31 & NX5K - 2 Port fc1/32 (san port-channel 10 on a VPC)

  Fabric B fc1/31 & fc1/32 passed to-> NX5K - 1 Port fc1/32 & NXFK - 2 Port fc1/31 (san port-channel 11 on a VPC)

  Thank you

  Ray.

  It is not possible. VPC is the only Layer 2 ethernet port channel. Port channel San cannot be built through vpc

  Sent by Cisco Support technique iPhone App

• IPS Inline Mode Interface - you can use a port channel?

  Hello

  I am trying to determine if you have a 2-gig Layer 3 Port channel through a 4260 IPS appliance. See the attached diagram. Is this possible?

  The customer, I work with would prefer not to enter this cost equal to Port-Channel 1 gig of links (I don't think that there is a difference in performance...) However, I think that if they want the device inline, as the diagram shows - they will have to break the port-channel. Is this a correct assumption?

  Thank you

  Brad

  Asymmetric traffic will prevent the sensor works best, he is capable. There is a configuration that can be done to allow the detector deployed in an asymmetrical environment, BUT it can affect the ability of the sensor to detect attacks, allows through evasions which would have been prevented and will not affect general performance of the sensor.

  If running in unbalanced mode should be avoided if possible. BT in cases where it cannot then the sensor always allows with degraded functionality.

  Traffic spikes above what the sensor can manipulate at will cause ignored packets. There is no help for too much traffic.

  The relief you talk I guess is the bypass function. The bypass feature does not affect during the subscription of the sensor. The bypass feature will only kick if the analytical engine crashes due to a bug.

• port channels

  I'm looking on the port channels configured on the FI. And that's all. port channel 21 is (eth 1/27-20) which is connected to the nexus 7000

  so, what are the others?

  (nxos) # sh port-channel summary

  Flags: D - low P - Up in the port-channel (members)

  I - individual H - standby (LACP only)

  s suspended r - Module-removal

  S - Dial R - routed

  U - up (port-channel)

  --------------------------------------------------------------------------------

  Group-Type Port Protocol Ports members

  Channel

  --------------------------------------------------------------------------------

  21 Po21 (SU) Eth LACP Eth1/17 (P) Eth1/18 (P) Eth1/19 (P)

  Eth1/20 (P)

  1286 Po1286 (SU) Eth NO Eth2/1/9 (P) Eth2/1/10 (P) Eth2/1/11 (P)

  Eth2/1/12 (P)

  1293 Po1293 (SU) Eth NO Eth1/1/9 (P) Eth1/1/10 (P) Eth1/1/11 (P)

  Eth1/1/12 (P)

  1298 Po1298 (SU) Eth NO Eth1/1/5 (P) Eth1/1/6 (P) Eth1/1/7 (P)

  Eth1/1/8 (P)

  1300 Po1300 (SU) Eth NO Eth2/1/5 (P) Eth2/1/6 (P) Eth2/1/7 (P)

  Eth2/1/8 (P)

  1306 Po1306 (SU) Eth NO Eth1/1/17 (P) Eth1/1/18 (P) Eth1/1/19 (P)

  Eth1/1/20 (P)

  1308 Po1308 (SU) Eth NO Eth2/1/17 (P) Eth2/1/18 (P) Eth2/1/19 (P)

  Eth2/1/20 (P)

  1311 Po1311 (SU) Eth NO Eth2/1/13 (P) Eth2-1-14 (P) Eth2/1/15 (P)

  Eth2/1/16 (P)

  1312 Po1312 (SU) Eth NO Eth1/1/13 (P) 1/Eth1/14 (P) 1/Eth1/15 (P)

  Eth1/1/16 (P)

  1315 Po1315 (SU) Eth NO Eth2/1/21 (P) Eth2/1/23 (P)

  1317 Po1317 (SU) Eth NO Eth1/1/21 (P) Eth1/1/23 (P)

  Tony,

  Port channels is those created implicitly by having the material of generation 2 (220 x, VIC 1240/80 and 62xx)

  These PC cannot be destroyed and cannot be seen through NXOS (UCSM-GUI will not display the)< thanks="" to="" my="" colleague="" jeff="">

  There is another discussion in this same forum this morning:

  https://supportforums.Cisco.com/message/4013409#4013409

  I hope this helps

  -Kenny