Portege R500 - neoprene

Similar Questions

• Password BIOS in Portege R500

  Hello!
  I found my old laptop, but cannot start - forgotten BIOS password. Disconnect CMOS battery did not help.
  Local support asked me to service offline, but they want too much money to unlock - this laptop is now less expensive itself.
  Support of the USA asked me write here
  May be someone can help generate answers unlock code?
  Model is Portege R500 PPR50E-06W012RU

  Protection of the BIOS is a very important feature for protection, so it cannot be discussed in the public forum.
  If someone writes here how you can remove the password BIOS all stolen Portege R500 can be unlocked.

  I know that it costs a bit, but this should be done by the authorized service provider.

• Portege R500 - RAM and disk SSD upgrade

  Hello

  I have a PORTEGE R500 bought in 2007, SERIES NO.48025469H.

  I have obvious problems with VISTA and WINDOWS 7. The two do not work well, because he seems to have a memory. I wonder if I can increase the memory and replace the drive with an SSD. I want to keep this laptop because it is perfect for all my needs.

  Thank you

  Message was edited: assignment has been translated

  Hello

  According to the specifications of the laptop your laptop can handle with GB of RAM, but has been bundled with 2 GB memory is not possible.
  http://www.Toshiba.it/discontinued-p...Tege-R500-11z/

  What about SSD? SSD upgrade is possible and you can use 256GB SSD for upgrade. After this system will be much faster, and you will certainly more performance and speed.

• Portege R500 - network Constant interruptions

  I have a Portege R500 with Windows XP (SP3 now, but same problem with SP2 and same problem before and after all reinstall them), and the network continues to interrupt. It's desperately irritating, because I work a lot of ssh connections, and almost every time the connection breaks I lose some work. The best of cases, it's that I have to log in again and continue where I was.

  This happens regardless of whether I use WIFI or wired network, and sometimes little matter where I am - home, office, coffee internet, that, is not my connection. The network is interrupted every 15-30 minutes, and sometimes as I type or loading a page, while other times it seems just to occur. It is usually easy to tell when it happens, because all the ssh connections instantly hang, all my messenger connections are broken and Outlook complains that he has lost the connection to the Exchange Server. The connections Outlook and messenger do not realize anything is wrong before the connection started actually working again, which has probably something to do with TCP or ICMP messages finally get through, but it's really strange that TCP is not only address the problem transparently - the physical connection is never interrupted for long.

  I guess that it probably has something to do with energy saving, but I have been unable to resolve in setting energy saving settings. Also, I have the same problem, regardless of the question of whether the laptop is powered.

  (Probably?) it is not a hardware failure, because I don't have the same problem in Ubuntu Linux and memtest does not report the errors of memory. (Speaking of which, is there a memory testing tool or self test tool integrated with this laptop?).

  Any suggestion would be appreciated. I tried calling the number of local support twice, but it didn't help much to get there.

  Thanks a lot for this great info

• Portege R500: Pwdbank starts consuming 50% of CPU

  Hello

  I have a Portege R500 (it's great!), running Vista with SP1.
  However from time to time pwdbank.exe, the banking password part of TrueSuite, starts consuming 50% of CPU.

  I downloaded the last update, but it has not solved the problem.

  Has anyone seen this problem?

  Thanks in advance

  Why do you think that it s a problem?
  Maybe this application needs of these material resources from time to time

• Portege R500: Cannot restore Vista using Toshiba recovery disks

  I downgraded Vista to XP loaded factory.
  However, I would now like to restore back to Vista.

  I have disc 1 & 2 ' product Recovery DVD-Rom; Portege R500 disks.
  They are also marked "Windows Vista Business (SSD/PATA)" has been provided by Toshiba.

  I don't know how to use these discs to restore my operating system to Windows Vista. When I insert disc 1 and after loading some files, a message "cannot read the file source or disk - Preinst2.SWM" and I can not go any further.

  An instruction step by step would be greatly appreciated

  I wonder why you receive two recovery disks. As far as I know Toshiba Vista Recovery image is stored on a DVD.
  Perhaps you have received two CD

  In any case, have you tried to boot from the second disk? I mean the second recovery CD?

  Usually, recovery is not very sensitive. You must boot from the disc and should follow the instructions on the screen.

  The error cannot read from the source file or disk - Preinst2.SWM looks like a little to the Conference on disarmament would not readable or the CD/DVD drive would not read the disc properly.

• Portege R500 - low volume with Win 7 and Realtek driver

  Hello

  I have now installed Windows 7 on my R500 to prepare for the end of Windows XP to life.
  I've experienced this now with Windows 7 sound does not really work.

  Build-in speaker does not work and a speaker connected to the outside with amplifier can get just a little sound in the maximum amplification I googled and saw many people having similar problems.

  Does anyone know if Toshiba has a solution for this?

  Other people with laptop computers Portege have the same problem?

  Thank you
  Markus

  AFAIK the Portege R500 supports Realtek ALC262
  I googled and found some people having problems with low sound volume on other laptops from other manufacturers using the piece ALC262

  But I found the solutions :)
  Download the utility of small noise turn Mute Off after upgrade to Vista
  [Its utility to turn Mute Off | http://support.toshiba.com/support/viewContentDetail?contentId=1671893&pf=true] and unzip it with WinRAR or WinZip
  You will find a small file called "MuteOff". Run this file as an administrator and check if your sound would work.

  Note: All drivers should be installed as well as the Realtek audio driver.

  Your comments would be appreciated

• Portege R500: Card reader SD and ODD do not work - drivers needed

  I have laptop portege R500, product number: PPR50E-04X04WCE.

  last year, I changed the operating system and installed windows 7.
  Since then, I can't use the dvd drive or the sd card reader.
  And the control panel it apears two unknown devices, but I can´t find the controllers for these.

  What can I do to fix this?

  I assume you found unknown devices in Device Manager.
  Check it please http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78
  Here you can find instructions how to identify the unknown devices.

  I checked the Toshiba download under http://www.toshiba.eu/innovation/download_drivers_bios.jsp page and your Portege is listed there, but under the option ARCHIVE. It is supported for Win7 so there is no problem to install all the drivers available.

  Check it out please and let us know if you still have the same problem.

• Portege R500 - replacement of the keyboard - success

  After buying a new keyboard for the R500 on EBay about a year ago, I finally blew the courage to replace a badly scratched by a new keyboard. The reason I've waited? I was worried about how to get out the old keyboard (it is locked down to the chassis, and it was obvious that I have would hurt one during the withdrawal.

  There is a nice write-up general on how to disassemble a R500 here:
  http://www.irisvista.com/tech/laptops/Toshiba-Portege-R500/disassemble-laptop-remove-hard-drive.htm

  The description above is not to discuss the keyboard however, so here's some additional information and tips:

  * Read this whole procedure before you start - it's simple, but not for the faint of heart.

  * Shut down, unplug the power, remove the battery.

  * Make sure that you have the correct keyboard for your model. The US keyboard is p/n G83C000903US for example. One I removed was a Rev 1 and a new one, I had a Rev 2 (don't know the difference - they look identical). They can get as low as $40-mais check the part number before you buy.

  * The keyboard connector is located under the computer, and so you will have to take off from the bottom, carefully following the instructions in the link above.

  A couple of notes: (a) the cable Ribbon PCMCIA connector must be opened to disconnect the cable, as this is the only thing that prevents you from removing the bottom of the computer. You can easily do so through access memory on the back door, but BE careful not to damage the cable lock. It works by switch to the top the little plastic lever that is held in place by small pieces of plastic on the sides of the connector that flex * a little *. Be gentle with this connector. When you put it back later-connector, if you placed the cable all the way into the connector, you can lock with only slight pressure down on the connector, and it will snap into place.

  (b) there are other types of cable Ribbon connectors use too. For example, to unlock the keyboard connector, now visible also on the bottom of the deck, slide both ends of the connector in the direction where the cable plugs in. They are snug and will only move about 1/4 ", be gentle but firm.

  (c) the two tiny connectors blocks free access to the water of the keyboard do not have locks on them. We're a band with only a few drivers, and one is a red and white power connector. Just pull out them. All the other connectors, you will probably miss through requires unlocking, so be careful!

  _Now back to the keyboard: _

  Once you have managed to disconnect his cable on the bottom, turn the laptop and start to remove the keyboard on the edges. It is supported by many small pieces of sticky tape, 2 faces, and that's it. As the base of the keyboard is made of aluminum, it is likely that you will distort the keyboard a bit as release you it, even though it may be downplayed maybe using a tool like a rule or something plastic and pry with it. Take care of not to damage the connector of the Ribbon and try to ignore these scary cracking sounds that identify each section!

  Once you have turned it off, you must remove any excess tape before starting point and again put a bunch of small pieces of new, good quality 2-sided tape (such as 3 m). No need to use anything stronger or thicker - just put a bunch of parts everywhere on the base, especially near the edges and the space key.

  Now, finally, turn the keyboard in position, making sure that you screw the connector back Ribbon through to the correct place. Turn the laptop over and re - insert and lock the Ribbon connector (make sure that it is directly and fully forward lock connector). All other connectors back in too. Then come back and push down hard on all sections.

  Re-assembling, taking care to put the 4 mm and 6 mm screws in the right places and a tiny on the side.

  Cross your fingers and turn it on!

  Good luck!

  Thank mate for this review.
  Generally the replacement of keyboard is not really complicated and someone with small technician skills should be able to replace it

• Portege R500-S5001X will not start

  My Portege R500 arrested last night when displaying "my pictures" and I was not able to do restart upward.

  I removed the battery and turn the direct power, but when I power on I get the Toshiba with "Intel" page in the lower right and five icons feature lower downtown.

  It will not boot to Windows, I know I should know, but I "think" it works under XP.

  I have no recovery disks, he passed to us my father in law a few years ago and no supported drives has come that I can find.

  Can someone help please!

  Thank you
  Tim

  Hey,.

  Can you please verify certain things?

  You can start in safe mode? After you have powered on the notebook press key F8 to access the Windows Advanced Boot menu and select mode.

  If you cannot access the t Windows Advanced Boot menu, you must check the BIOS if the HARD drive is recognized correctly.

• Portege R500 - PPR50E replacement of the HDD or SSD

  Hello

  The hard drive in my beloved Portege R500 is dead.

  The model is a Toshiba MK1237GSX and am looking for a compatible hard drive to replace it with conclusion that this exact model turns out to be difficult. You can also and my first choice would be to replace the HDD with a ssd drive - is this possible and any recommendation on model?

  Any help is very appreciated

  Thanks in advance

  Agree with Akuma.
  You need an SSD that supports the SATA interface.
  You need disc SSD SATA 2.5

• Portege R500 - Bad optical drive delays the start - how to fix?

  The Portege R500 has recently begun does not start. Initially there not some time later, frequently. By chance, I discovered that if I left alone for a minute or two, he will continue to start. That and the noise coming from the optical driver, made me suspect the problem was not with the HARD drive, as I feared at first, but with the optical driver.

  I read in the thread below that other people had this problem. MrBear mentions * I pulled it out again and pushed on the Ribbon connecting the CD-ROM to make sure they were safe. Turned on again and he pulled up without problem! *

  Link: [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=43300&tstart=0]

  Could someone clarify in what ribbons must be treated? Only those who are visible by opening the drive? Or it is necessary to open the notebook?

  Furthermore, if I booted into Windows, it stopped again, for a minute or two, while Windows is loading. With Ubuntu, there is no such problem. Perhaps Windows tries to communicate with the optical driver for some reason any.

  Tnaks for any help!
  Leonardo

  Hello!

  Is your laptop still under warranty? If so I put t understand why you try to solve the problem by yourself. Go to the nearest EPA and ask a technician for help. These guys are very useful and they have the most experience on laptop repairs.

  On the Toshiba site, you can search the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  And the problem with Windows, it is difficult to tell why Windows stops for a minute. Maybe it s a software problem so disable all programs that you start n t need in msconfig.

  Good bye

• Portege R500 - maximum external screen resolution is only 1280 x 1024

  Hi all

  I just ordered R500 (WinVista), and a 20 "external monitor (connected via a VGA cable) BENQ G2020HDA (1600 x 900 native). However, the maximum resolution for external panels (installed correct driver) alloved by Vista (parameters > monitor) is 1280 X 1024 :-(((.))

  Do anyone have some tips, how to increase the resolution of the external monitor with this ntb Portege R500 (BIOS 1.6)?

  Thx for your help!

  Have you tried to update the display driver? You can find it on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Remove the old display driver in Add/Remove programs and then restart the computer and install the new driver to display on the Toshiba site.

  If it doesn't work you should try to update the BIOS. You can also find it on the Toshiba site.

  Good luck!

• What is the difference between Portege R500-121 and R500-11z

  Hello

  What difference is between model Portege R500-121 3 G and R500-11z?

  Thank you

  The two supports of laptops:

  PROCESSOR - INTEL CORE 2 DUO U7700 (1.33 GHZ) PROCESSOR
  GPU - INTEL 945GMS
  DISK HARD - 160 GB (5400 RPM) SATA
  FINGERPRINTSENSOR
  11 a/G/N INTEL wireless network card

  And the only difference is that R500-11Z does not support the * module * 3 g!

• Portege R500 Toshiba 19AV505D TV LCD connection

  I want to connect my Portege R500 laptop to a Toshiba 19AV505D LCD TV.

  I tried to use a HDMI VGA cable and change the screen resolution of 800 x 600 and 16-bit color, but it does not recognize the tv.
  Any ideas?

  Device manual says use a DVI cable to HDMI and I tried this first with a VGA Converter (as there is no socket DVI on the R500) but that didn't work either.
  Would be a SCART to VGA cable work?

  What VGA-> HDMI adapter are you using?

  What version HDMI support?

  Maybe the TV requires HDMI v1.2 or v1.3 (see user manual)