Ports usb 3.0 HP M6-1045dx for right side do not work
I just changed the motherboard and the hard disk cable in my m6-1045dx and it seems to work without accident for now.
Now, I can not USB 3.0 ports right to work. I plug anything on them and they don't work at all.
Here's what I've tried so far:
I tried to uninstall the drivers and reboot. The laptop and reinstalled the drivers but they did not
I tried to install a driver wifi intel and who did not
I tried to install the usb 3.0 intel chipset driver and who did not
Help, please. I don't know where else to go. Thanks in advance
Here's what I did.
I took out the battery.
I removed the large bottom panel.
I removed the small panel for the wireless card see if I could see the two screws that connect the usb 3.0 ports and fortunately I did.
I have check the tightness and the screws were really tight.
I decided to unscrew the two screws and lifted the backend of the usb 3.0 a little Board. I then sprayed some CRC QD electronic filter on the contact areas.
I put the two screws back in and tightened their top as much as possible without stripping or breaking the jury.
I put the panels back on and put the battery back in.
He started upward and to my surprise, the USB 3.0 ports worked perfectly.
Until the problem of USB 3.0 port, the motherboard has been changed then maybe contacts to be cleaned. That's my guess.
Pepe999, thanks for the replies. I appreciate it.
Tags: Notebooks
Similar Questions
-
Satellite P850 - 12Z USB 3.0 Ports right side do not work USB 3.0 speed
Hi all
I bought a portable Satellite P850-12Z with * 4 * USB 3.0 ports. Two ports on the left side and two ports on the right side with sleep functions and fresh.
If I connect an external drive Verbatim USB 3.0 ports on the left side, everything works fine. Transfer rate is about 70-90 MB/s, but if I connect the * same drive * USB ports on the right side I see the pop up message "this device can perform faster if you connect it to a Super Speed USB 3.0 port" and the transfer rate is about 20-30 MB/s. These ports operate as USB 2.0 ports.
I repeat that all the available ports on the laptop are USB 3.0.
Anyone know what is happening with ports USB 3.0 on the right side?
I don't have another USB 3.0 drive to do more tests.
Thank you
Carlos
> I repeat that all the available ports on the laptop are USB 3.0.
You are absolutely right.
I ve checked specification s notebook, and all ports are USB 3.0 ports.It is not easy to say what the problem is here.
What you can do is to contact the nearest Toshiba service provider and ask for explanations.
They know what the problem is here.Maybe a few update driver or BIOS update offered in the future will solve this problem. In my opinion, you should continue to use the ports on the left side for data transfer.
-
Add-on for Print Edit does not work
I just got my iMac cleaned for adware and now my add-on for print edit does not work. There is an error 2 - XPF to the catalog. I don't know the email address of support for developers?
Hello
Did you mean this extension:
The contact details are on the right side of the page, next to the section 'on this add-on.
-
original title: Halo 2 for windows vista
Halo 2 for windows vista does not work on my windows 7. Saiys it cannot start the direct customer. It will not work in single user either...
Hello
Plase make sure you have the latest version of the GFWL Client installed:
http://www.Microsoft.com/games/en-us/live/pages/livemarketplace.aspx
-
short cuts on the desktop for the URL will not work. Try to connect the browser when rises the address has not been transposed, it's all just white
There may be some problems that repair tools are not picking up. It may be preferable to a repair facility. This can help with any corruption of the registry, which could happen by the deletion of these programs. http://support.Microsoft.com/kb/917964
Keep in mind when running all that modifies the system it is always a good idea to have your data and backup programs (it's general advice for any system its always good to have a backup in case of possible failure of material/virus)
-
STOP: 0x0000007e (0xc000001d, ox8537008 0xba4c3508 0xba4c3204) and the system would not come to the top.
Error blue screen STOP: 0x0000007e. I powercycled the sys, unable to choose for sure (keys do not work when you try to select a mode) sys is trying just to go back to the blue screen. Help, please
Symptoms: Booted computer, loaded the raid drivers and showed at the start screen XP for half a second then to BSOD with a Stop error Code 0x0000007E - see also a lot of users (0xC0000001D, 0 x-, etc.) as well.
Solution:
1 boot from your Windows XP CD and start the recovery console. You may need to press F6 while RC loads in order to load the SATA drivers. you will have a prompt c:\WINDOWS to the console.
2. type: CD $NtUninstallKB977165$ \spuninst (it's the update, I had to uninstall to get out of the boot loop, other updates can be uninstalled by changing the name of the directory to $NtUninstallKBCODE$, where KBCODE is the code KB)
3. type: BATCH spuninst.txt
4. type: exit
Don't forget to configure your system to boot from the HD before resuming. I hope this helps. Saved me a lot of hassle today.
-Tom Steele
http://www.hawkandtom.com Tom Steele -
Ringtones for my contacts do not work if the (Torch 9800) handset is locked; the default / everyone of another ring is used instead. When the handset is not locked, it works well. Someone knows how to fix this?
[Title edited to reflect the new subject.]
@ City
Maybe you have enabled a content protection?[Title edited to reflect the new subject.]
-
. FN/F5 and F6/Fn keys for brightness adjustment, do not work
Hello Gloria
I installed Windows 7 on my computer sony vaio ns notebook series. FN/F5 and F6/Fn keys for brightness adjustment, do not work. In the previous installation of Vista, they worked without problem.
adjusting keys for his work, but not show the cursor on the desktop.
can help you with some advice.
Thank you... :-)Run Windows Update. It is good for the installation of device drivers that have not been found during the installation of Windows 7.
If that doesn't fix it, you may download and install the device drivers for your computer from Sony model.
-
HY, I used to use your adobe photoshop cs6 I have my laptop. some of the reasons for my laptop was not working, so I've restored my laptop. I have tried to reinstalled photoshop with old license No, but his does not work. what I would do.
Please return to the message sent to you.
-
Is there a 32 bits 4 lightroom to download for 64-bit does not work on my pc
Is there a 32 bits 4 lightroom to download for 64-bit does not work on my pc. 64-bit pshop CS6 won't work either, but 32 bit only!
I can't speak for the version of Windows. It comes in a zip file, and when it is decompressed it creates an Adobe file. Inside of this file is the installer and another folder. If you open the second folder, you can see the installation of 32-bit and 64-bit programs. This is the 32-bit appropriate in your case, and you should be good to go.
-
help that my usb ports on the left side do not work
I have a hp pavilion dv6-6117dx. the usb ports on the left side are stoped working. I need help please...
A factory restore can't hurt, and it can fix it. First of all, I think I'll try re-installing the AMD graphics driver which usually includes the motherboard drivers.
-
Ports USB of W520 left side do not work.
Hi everyone, I'm running a problem. I am using usb ports located on the left side, but they do not work. I plug my mouse to one of the USB ports and when I start my computer, I can see the mouse works because it turns on, but then once the windows screen it shuts down and I can't use it. Someone at - it indexes? I tried to connect it to a USB flash drive, just in case it was just the mouse and it does not work either.
I went into Device Manager and looked at the USB, but there were few of them. I uninstalled and reinstalled the following: usb generic, generic usb host USB 3.0 of renesas. There was a message that says: "bluetooth device not found."
I checked the BIOS and everything is enabled.
NEVEMIND. workaround. "" I looked under the "other devices" option and I saw that there was an unknown device which has not installed correctly. I went under 'Properties', then went to the tab "driver". I got the update and he gave me a warning about an unknown device installation, but I went to come some way and everything works now.
Incase anyone has the same problem, here is how things should look like once the left side usb working and installed.
-
USB connection for speakers/conrtols do not work?
Hello.
My daughter has a bed that connects to an MP3 player via a USB connection and speakers and play controls on it. SanDisk Sansa clip plus is not working, looks like he's trying to connect to a computer to receive information. Is there something I should do differrently or if this feature is not supported with this MP3 player?
A bed that connects to an Mp3 player? Cool!. The Clip + has two modes, the MTP and MSC mode (settings > system settings > USB). If you transfer files under the PSG, the songs will not appear on the computer when you connect in MSC mode and vice versa. Most likely your bed does not recognize MTP peripheral devices. That being said, try transferring music on both msc and mtp and do a test. Try to connect the Sansa to your bed under MSC and MTP.
-
Search iPhone settings for "Auto-Lock" does not work
Hello
Does anyone know why the Auto-Lock setting is not to be found when you use the search at the top of the main settings page.
From time to time, when I'm on a conference call, I like to set the auto-lock on 'Never', so I can leave the visible main phone screen to mute/one-mute the call without having to unlock the phone. I have the memory of a goldfish, so I do not remember that it is in the section "Viewing and brightness" and that is why I use the search at the top of the main settings page field. I would normally enter 'Auto', and it would be "Auto-Lock" for me.
Since the release of iOS10, the la recherche search can't find this definition more although it still is in the section "viewing and brightness.
The search for other settings seems to work, but it seems that it is just this one, but I have not actually tried too.
Any ideas on what is happening and how I could get to find the Auto-Lock in the future?
Thank you
B1GPappaSmurf wrote:
Any ideas on what is happening and how I could get to find the Auto-Lock in the future?
Seems to be a bug, so nothing you can do but remember where the parameter is and report the bug:
-
IOS10 email for signature markup does not work now. Help, please!
I used much markup of the email for signing off e-docs. However, I found that it does not work now after the upgrade to iOS10. After set up my signature recorded and distributed, the beneficiaries, said the e-docs they received was not my signature signed on them (which was in previous iOS).
That it would be much appreciated if someone could help solve this problem. Thank you.
It might be a bug in iOS 10. It might be helpful to reach out to the Apple support for him noting if this is a bug.
Maybe you are looking for
-
HP Slimline S5 - 1120D: how to use VGA internal?
Hello I am currently using Windows Update to 10 anniversary and my screen turns off after a few minutes I have to play the game. It says "VGA: No Signal. How to use the other port VGA on my PC? Currently, they are covered with plastic and has "do not
-
iPhone battery 6 dies in the cold
Battery died on my iPhone 6 cold weather. Phone is about 15 months and died of battery in good condition 50% to 30% down to nothing and automatic switch off. THE normal time the battery is still very good and doesn't show signs of weakening on any no
-
How can I update my system registry for Flipshare software?
I tried to download the flipshare software and have had problems. The site of camera Flip told me I need to update my Windows registry database.
-
I recently downloaded Secure browser review for a test in Spanish for a class. I uninstalled the program successfully, however I still can't access my Manager tasks, Shut Down, restart, sleep and Hibernate options went on the Start Menu. Finally, b
-
Hi friends, In blackberry so many screen resolutions are there. 320 x 240 (curve 8520), 360 x 480 (bb 9550), 480 x 360 (bold 9700) For my project, I need to design this 3 resolution separately. Based on the screen size resolution images will be diff