Power HP Pavilion Slimline s3000 supply problems

Similar Questions

• The HP Pavilion Slimline s3000 is not able to be disconnected from the monitor?

  I have a HP pavilion slimline S3000 and I don't know how to disconnect the HP monitor. I don't know how to disconnect the power cord of a something blue wide at each end, which does not seem to get out of each end. Is it possible to disconnect so I just the screen and if so, how?

  Thank you.

  Hello

  Looks like you have the VGA cable that is connected to the port #12

    

  Figure 9: Rear i/o panel

  

  Very simple, it is fitted with two screws, you can turn by hand or use a screwdriver to remove

  Kind regards.

• HP pavilion slimline 400: a problem about the upgrade card chart, power, and a new case

  I have a hp pavilion slimline 400 and I want to upgrade the graphics card of it. However, the food is not enough for my new graphics card. The image is too large for this case. SO I decide to buy a new case and PS! Move all the thing inside the hp pavilion slimline 400 to a new case. But I heard someone say that this kind of PC can match the case that we can buy in the store and the cable of the PIN from those of food on the market do not correspond with the motherboard. CAN I really do that?

  You will still need a case that supports the Μatx layout.  I/O back plate must be modded or replaced to adapt.  Most cases have both Μatx and ATX layout (dead end of pines).  For some time that this question of stitching was done.  These help?

  

• can I upgrade power 220w Pavilion slimline

  I can replace the power supply 220W in a Pavilion Slimline 400-034 with one that has the most power.

  Hello seyabt,
  
  
  
  To be able to know if you are able to replace the power of a higher power, I would need to know the full of your computer model number. I've included the document 'Guide to finding your product number'.
  
  
  
  Thank you.

• Pavilion Slimline 400: Installation problem

  I tried in vain to install my old Bejeweled game on my brand new HP Pavilion Slimline 400 office.  No matter how many times I clicked on the Install of the game on my screen button, nothing happened.  Oddly, I had no problem installing the same game on my laptop.  The computer is running Windows 7, while the desktop is running Windows 8.1 (I don't know if it's 32-bit or 64-bit).  The version of Windows would have something to do with it?  Is there something I can do?

  If you can read the whole page, you will notice that the OS is Win7.  No mention of Win8. You can find new versions for WIN8 on the web.

• Pavilion Slimline s3400f: HP slimline s3400f desktop bluetooth

  HP Pavilion Slimline s3400f desktop PC - this computer has Bluetooth devices listed on the control panel.  I have a set of 2 wireless speakers UEBoom I want to use with the computer.  I lit one of the speakers and proceeded to Bluetooth devices on the control panel of my PC and clicked on add a device.  There is nothing listed in the window "pair with a wireless device.  I tried to move the wireless speaker more far, I have had it too close to the thought and still nothing.  What should I do to use these speakers with this computer?

  Hello:

  According to the page of product specifications for your PC on the link below, it comes with Wi - Fi networks and without bluetooth.

  http://support.HP.com/us-en/product/HP-Pavilion-slimline-S3000-desktop-PC-series/3688715/model/3688723/document/c01374065/

  Windows has settings for adding bluetooth devices, but you also need the material.

  Think that buy you an external usb bluetooth adapter.

  I use this one...

  http://www.Amazon.com/Kinivo-BTD-400-Bluetooth-4-0-USB/DP/B007Q45EF4

• Pavilion Slimline s3100n: BIOS PW help

  My HD crashed after a complete upgrade to Win10 by a Win8 OSvpurchase. I'm coming back. I reformatted a hard drive and CD recovery, but when I start and go to the BIOS it requires a PW. Don't know who. How do I move forward again? Thank you.

  Hello:

  Please see the last section on the link below... Clearing BIOS settings > remove BIOS password...

  http://support.HP.com/us-en/product/HP-Pavilion-slimline-S3000-desktop-PC-series/3440811/model/3440346/document/c00910076/

• Can I put the Pavilion Slimline 180 Watt power supply to a 300 Watt PSU

  Of course, you can!

  Here is an informational videoabout the possibilities of upgrading your slimline WHAT PSU found on YouTube.  A comparison of three power supplies, including the owner HP PSU and a (two video and CPU) stress test and comparison of noise is shown during the video.

  Be aware that some, but not all, of the PSU, upgrades require a simple and light your PSU slimline support change. Change depends on the power supply model chosen for the upgrade.

  Purchase an adaptor molex as HP UPE is necessary for the Slimlines using a power supply with the format owners microfit ATX 24 pin, as well as the standard for the HTPC power supply ATX 20 pin format.

  Upgrade your power supply at a higher power will not damage your motherboard. A power supply will provide only so much power that is required of him by the mother and peripheral card up to the nominal power of the installed PSU.

  It is for those who wondered how to work around the limitation of the low power 180 Watt power supply that most Pavilion Slimline PCs come with the Assembly. With a power SUPPLY improved, more memory and a graphics card discrete, including support (it is a requirement) your Slimline can be your gaming PC.

  Selecting a graphics card is another topic. Not all graphics cards can hold in the case of a slimline. It takes a low profile video card. They are available for purchase online.

  Kind regards
  ERICO
  Published by erico on 15/11/2009 13:17

  Bravo for Erico 1,000,000,000. Great post. Debunks many myths and the hearsay rule.

• Pavilion a6655f: hard drive or power supply problem?

  A few days ago, I was trying to low loading part of the steam.  My download speed is 30 kbs, obviously not good.

  I did some basic checks, malware, viruses, etc., but did not find any problem.  I did a diagnostic check and got a BIOHD-8 error code, which indicates a hard drive problem.  I decided to try to reset the computer back to the factory setting before changing the hard drive and once that I made and updated windows Vista for several hours, I restarted the diagnosis and he came clean.  Then I updated my software, including steam and a few games.  Downloads were fast and had no problems.  Later that night the computer started to shut down randomly, and I was unable to run any games.  Thinking it's maybe a power supply problem, I have replaced my graphics card with an elder who needs less energy.  I am able to run without any problems so far.  So, I'm looking for help in identifying my problem.  HDD problem, power supply, something else?  Any thoughts are appreciated.

  Pavilion a6655f

  Windows Vista

  PS 500 watts

  WD hard drive provided with the computer

  Thank you.

  Ken

  Hard to say without proper trials.

  You can use a hardware monitor HW Monitor to monitor tensions it is: http://www.cpuid.com/softwares/hwmonitor.html
  But there is no software that can test a power supply.

  You can get a tester of hardware like this too: http://www.newegg.com/Product/Produc...82E16899887005

  But there is really no of it will predict fails if the power supply, if you overloaded it, if its duration in time high, or if the power supply is a device of poor quality that can be subject to failure.

  You can also check that your power cable is comfortably installed on the computer and not frayed.  Try a different wall jack where there are fluctuations in power.

• HP Pavilion Slimline s5-1200z improvement of power supply

  Hello

  I need to replace a power supply broken for the HP Pavilion Slimline s5-1200z Office I bought in June 2012. As I improved the memory of 8 GB 3 months ago, I would like to take this opportunity to improve to 400w 300w 220w power, if possible.

  Unfortunately, I can't find any power supply suitable for the Pavilion Slimline s5 series, in-store or online. The only one I can find is the replacement of the part #633195-001 of HP on HP website. Any recommendations?

  It is sold on eBay, and says it's an upgrade of 330w PSU for your model:

  http://www.eBay.com/ITM/like/271337685300?lpid=82

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP pavilion slimline s3632me graphic card problem

  It's my computer: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c01552288 & lang = to & cc = us & conte...

  my graphics card has a fan that is not working, and I don't get any signal on my monitor after 20 minutes of start... so I decided to get a new graphics card which is better.

  so I want to know what is the max graphics card that I can put in this computer and should I go for the same type (AC express graphics card) or get any type that can work with the computer?

  Here are the specifications of your HP Pavilion Slimline s3632me desktop computer and its card mother M2N61-AR (Acacia). Based on the specifications, this model has a power of 160 watts, a graphics card NVIDIA GeForce 9500 GS PCIe x 16 HDMI and DVI - I outputs and integrated nVidia GeForce 6150SE graphics with a VGA output. Note that the discreet graphics card and the built-in graphics card is not usable at the same time.

  You need to replace the graphics card NVIDIA GeForce 9500 GS PCIe x 16 with a x 16 low profile PCIe graphics card (the card must have a power system recommend assessment of 160 watts or less). All purchased card that has a higher recommended system power supply requirement will require the purchase of a new power supply, follow the recommendations in cards. Your computer's power supply is not a standard ATX power supply and can be difficult to find.

  Please send Bravo

• Pavilion Slimline lock up in sleep mode-fan works high not lights up unless I pull the power cord 1

  New HP Pavilion Slimline desktop 400-314 - mode 'sleep' sometimes cause to lock the computer, the power light is on, the fan runs at the top.  Only way to unlock the computer is to hold the power button for 5 seconds.  I wait 15-20 seconds, then press the power button to wake it up.  Immediately the computer restarts to the top with solid power light and the fan turns at the top.  The only way to break this vicious circle must first pull the power cord to the rear, wait 30 seconds and plug it in again.  This time, when I turn on the computer it goes off just fine.

  Is this a BIOS problem?  Please help as I don't have that much hair left.

  * Solved * Finally!  After 8 grueling days of pain staking agony and incessant attempts to fix this thing, I finally solved my problem.  I spent countless hours on the phone with HP support and nothing resolved.  That is: the problem with this computer locking up and sending the fan at high spin was due only with external speakers. When you reset the power system disconnected to boot the system, he would normally go for at least half a day before locking up.  I discovered that the speakers are older than 15 years. It's funny, these speakers worked fine on a desktop HP 2004 previous Pavilion running on Windows XP.  Now, it's static build-up that caused my death or something else?  As far as I know, it's that I'm a happy camper using headphones with a new system of HP that finally works.  Thank you to everyone who made suggestions.

• HP Pavilion Slimline s5298d had blue screen problem. Error: IRQL_NOT_LESS_OR_EQUAL (a).

  Hello!

  Can someone solve the blue screen of my PC problems?

  My PC always appear blue error screen especially whenever I stop PC.

  Error message: IRQL_NOT_LESS_OR_EQUAL (a).

  Arguments:
  Arg1: ffffffe5, memory referenced
  Arg2: 00000002, IRQL
  Arg3: 00000000, bit field:
  bit 0: value 0 = read operation, 1 = write operation
  bit 3: value 0 = not an enforcement operation, 1 = performance operation (only on chips that support this level of State)
  Arg4: 820d3a6a, address memory
  The blue screen issue can be caused by ntkrpamp.exe (nt! ExpScanGeneralLookasideList + 22)
  PC model: HP Pavilion Slimline s5298d
  Operating system: Windows 7 Home Premium 32-bit

  Hi once the device is powered keep tapping F2 button then start the hard drive & test control memory if a test fails, you will need to replace the part if test passes following the steps below. Then you can try the F8 key when the power is on and try the last known good configuration. If this does not work try start repair and try to repair the unit. If these options above does not work you can try to do a system recovery restore or F11 before this please back up your data as it will be lost.

• HP Pavilion Slimline s5-1414 connection LCD monitor & projector problem

  I bought a HP Pavilion Slimline s5-1414 with Windows 8, for my church, which came standard with 2 DVI ports. I attach a LCD monitor to 1 Port and a projector to another. Start the computer and both screens remained blank. I disconnect me the projector, restart the computer and the monitor running normally. I then connect the projector in the other port and it works as expected. However, when I restart the poster blank rest until I have do as above. I also reset the BIOS to the default settings, and both screen and projector came fine. Yet once, when I restarted, same problem. I manually set the resolution for both devices. Problem remains - every time that I reboot, displays may not run until I disconnect the projector, reboot, and after successful reboot, reconnect the projector. Any suggestions?

  Thank you for running these tests and getting back to me. I think that it is prudent to exclude at this stage of material. I have two options for you to try.

  I would like you to reinstall the graphics driver.

  Press the Windows key + Q to bring up the search

  Type 'unit'

  Click on Device Manager

  Expand graphics cards

  Double-click Intel

  Click the driver tab and click the uninstall

  Restart the computer

  Windows will automatically detect the missing driver and reinstall it on reboot. Once you are in the start screen of Windows, shutdown, connect two screens (a screen and a projector or two monitors, anyway) the computer turn on and I would like to know what the results are.

  I would also try both screens set before to turn on/off mode safe. You may need to press and hold the ESC key lighting to get the option come up, instead of SHIFT F8 as set out in section. Take a look at this article to get the procedure start mode safe. Let me know what you find

• How to remove power on password on hp pavilion slimline s5-1114

  How to remove power on password on hp pavilion slimline s5-1114

  Hello

  See the subheading "Compensation password settings", on the following link.

  http://support.HP.com/us-en/document/c02980014

  Kind regards

  DP - K